Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Design Guide
for Canada
Supplement to the
Hilti North American
Product Technical Guide
2013 Edition
Mechanical Anchoring Systems
Hilti has it! – Proven and Approved Anchoring Solutions for CSA A23.3-04 Annex D
Best in class.
HSL-3 expansion anchor
This heavy-duty expansion anchor offers high
reliability and superior installation safety.
UÊ }
Ê>`ÊV>«>VÌÞ
UÊ Û>>LiÊÊÎÊ
i>`ÊVw}ÕÀ>ÌÃ\Ê
iÝÊ
i>`]
torque cap or stud
UÊ ,i>LiÊV>«}ÊvÊ«>ÀÌÊv>ÃÌii`ÊÌ
overcome gaps
UÊ iiÀ>ÞÊÃÕÌ>LiÊvÀÊ`Þ>VÊ>`}ÊÊ Ê
Ê VÕ`}ÊÃiÃV]Êv>Ì}ÕiÊ>`ÊÃ
V
Table of Contents
*À`ÕVÌÊiÃVÀ«ÌÊÊÊÊÊÊÊ2
Material Specifications - 2
Technical Data - 3
HDA Design Information for CSA A23 Annex D - 4
Sample Calculation - 6
Notes for Design Tables - 8
>VÌÀi`Ê,iÃÃÌ>ViÊ/>LiÃÊÊ/iÃÊÊÊÊÊÊ9
>VÌÀi`Ê,iÃÃÌ>ViÊ/>LiÃÊÊ-
i>ÀÊÊÊÊÊÊ£3
Installation Instructions - 23
Ordering Information - 25
*À`ÕVÌÊiÃVÀ«ÌÊÊÊÊÊÊÓ7
Material Specifications - 27
Technical Data - 28
HSL-3 Design Information for CSA A23.3 Annex D - 29
Sample Calculation - 30
Notes for Design Tables - 31
>VÌÀi`Ê,iÃÃÌ>ViÊ/>LiÃÊÊ/iÃÊÊÊÊÊÊÎ2
>VÌÀi`Ê,iÃÃÌ>ViÊ/>LiÃÊÊ-
i>ÀÊÊÊÊÊÊÎ6
Installation Instructions - 49
Ordering Information - 49
*À`ÕVÌÊiÃVÀ«ÌÊÊÊÊÊÊx0
Material Specifications - 51
Technical Data - 52
KB-TZ Design Information for CSA A23.3 Annex D - 53
,/<ÊiÃ}ÊvÀ>ÌÊvÀÊ
-ÊÓΰÎÊiÝÊÊÊÊÊÊÊx4
Notes for Design Tables (Carbon Steel KB-TZ) - 57
>VÌÀi`Ê,iÃÃÌ>ViÊ/>LiÃÊÊ/iÃÊ
>ÀLÊ-Ìii®ÊÊÊÊÊÊx8
>VÌÀi`Ê,iÃÃÌ>ViÊ/>LiÃÊÊ-
i>ÀÊ
>ÀLÊ-Ìii®ÊÊÊÊÊÊÈ5
ÌiÃÊvÀÊiÃ}Ê/>LiÃÊ-Ì>iÃÃÊ-ÌiiÊ ,/<®ÊÊÊÊÊÊn8
>VÌÀi`Ê,iÃÃÌ>ViÊ/>LiÃÊÊ/iÃÊ-Ì>iÃÃÊ-Ìii®ÊÊÊÊÊÊn9
>VÌÀi`Ê,iÃÃÌ>ViÊ/>LiÃÊÊ-
i>ÀÊ-Ì>iÃÃÊ-Ìii®ÊÊÊÊÊÊ3
Installation Instructions - 115
Ordering Information - 116
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 1
Mechanical Anchoring Systems
Mechanical Properties
1.2 Material Specifications fy min. fu
MPa MPa
HDA-P HDA-T HDA-T/-TF/-P/-PF carbon steel cone bolt; M10, M12, M16 and M20
Heavy-Duty Heavy-Duty
Undercut Anchor Undercut Anchor meets strength requirements of ISO 898, class 8.8 640 800
(Pre-Set Type) (Through-Set Type)
HDA-T/-TF/-P/-PF carbon steel sleeve; M10 & M12
conforms to European Standard No. 25CrMoS4 – 850
HDA-T/-TF/-P/-PF carbon steel sleeve; M16
conforms to European Standard No. 25CrMoS4 – 700
HDA-T/-TF/-P/-PF carbon steel sleeve; M20
conforms to European Standard No. 25CrMoS4 – 550
HDA-TR/-PR stainless steel cone bolt; M10, M12 and M16
conforms to AISI 316 or 316 Ti 600 800
HDA-TR/-PR stainless steel sleeve; M10 and M12
conforms to AISI 316 or 316 Ti – 850
Components
HDA-TR/-PR stainless steel sleeve; M16 conforms to AISI 316 or 316 Ti – 700
UÊ-Ì«ÊÀÊ Ì HDA-T/-TF/-P/-PF nut conforms to DIN 934, grade 8
HDA-TR/-PR nut conforms to DIN 934, grade A4-80
UÊ-iÌÌ}Ê/
HDA-T/-TF/-TR/-P/-PF/-PR washer conforms to DIN 6796
UÊ,Ì>ÀÞ HDA-T/-P components are electroplated min. 5 μm zinc
Hammer Drill HDA-TF/-PF sherardized components have average 53 μm zinc
2 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
t fix
do baseplate
dh
t fix
dh
Blank-carbon steel zinc plated
F-carbon steel sherardized
R-R-316 stainless steel
Drill bit diameter (mm)
h ef
h ef
ho
ho
Metric
h
h
Thread diameter (mm)
HDA-PF 22 M 12 x 125 / 50
Minimum embedment of undercut
Maximum fastening thickness
HDA-T d bit HDA-P d bit
Table 1 - HDA Specifications
Anchor Size HDA-T/HDA-P M10 x 100/20 M12 x 125/30 M12 x 125/50 M16 x 190/40 M16 x 190/60 M20 x 250/50 M20 x 250/100
h Thickness of base
material, min.1 mm (in.) 170 (6-3/4) 190 (7-1/2) 190 (7-1/2) 270 (10-5/8) 270 (10-5/8) 350 (13-3/4) 350 (13-3/4)
Total anchor length mm (in.) 150 (5.90) 190 (7.48) 210 (8.27) 275 (10.83) 295 (11.61) 360 (14.17) 410 (16.14)
length I.D. code2 letter I L N R S V W
tfix Fastening thickness
HDA-T, min.3 mm (in.) 10 (0.39) 10 (0.39) 10 (0.39) 15 (0.59) 15 (0.59) 20 (0.79) 20 (0.79)
HDA-T, max. mm (in.) 20 (0.79) 30 (1.18) 50 (1.97) 40 (1.58) 60 (2.36) 50 (1.97) 100 (3.94)
HDA-P, max. mm (in.) 20 (0.79) 30 (1.18) 50 (1.97) 40 (1.58) 60 (2.36) 50 (1.97) 100 (3.94)
d bit Nom. dia. of drill bit4 mm 20 22 22 30 30 37 37
ho Min. depth of drill hole mm (in.) 107 (4.21) 134.5 (5.30) 134.5 (5.30) 203 (7.99) 203 (7.99) 266 (10.47) 266 (10.47)
h ef Effective anchoring depth mm (in.) 100 (3.94) 125 (4.92) 125 (4.92) 190 (7.48) 190 (7.48) 250 (9.84) 250 (9.847)
dh Recommended clearance
hole (min.) HDA-T mm (in.) 21 (7/8) 23 (15/16) 23 (15/16) 32 (1-1/4) 32 (1-1/4) 40 (1-9/16) 40 (1-9/16)
HDA-P mm (in.) 12 (1/2) 14 (9/16) 14 (9/16) 18 (3/4) 18 (3/4) 22 (7/8) 22 (7/8)
do Anchor Diameter, HDA-T mm (in.) 19 (0.748) 21 (0.827) 21 (0.827) 29 (1.142) 29 (1.142) 36 (1.42) 36 (1.42)
HDA-P mm (in.) 10 (0.394) 12 (0.472) 12 (0.472) 16 (0.630) 16 (0.630) 20 (0.78) 20 (0.78)
dw Washer diameter mm (in.) 27.5 (1.08) 33.5 (1.32) 33.5 (1.32) 45.5 (1.79) 45.5 (1.79) 50 (1.97) 50 (1.97)
Sw Width across flats mm (in.) 17 19 19 24 24 30 30
Tmax. Max. tightening torque5 Nm (ft-lb) 50 (37) 80 (59) 80 (59) 120 (88) 120 (88) 300 (221) 300 (221)
Sleeve properties
A sl Cross sectional area mm2 (in2) 196 (0.304) 223 (0.346) 223 (0.346) 445 (0.690) 445 (0.690) 675.6 (1.047) 675.6 (1.047)
S sl Elastic section modulus mm3 (in3) 596 (0.0364) 779 (0.0475) 779 (0.0475) 2110 (0.1288) 2110 (0.1288) 3950 (0.241) 3950 (0.241)
Bolt properties
Ab Bolt nominal area mm2 (in2) 78.5 (0.122) 113 (0.175) 113 (0.175) 201 (0.312) 201 (0.312) 314.16 (0.487) 314.16 (0.487)
At Bolt tension area mm2 (in2) 58 (0.090) 84.3 (0.131) 84.3 (0.131) 157 (0.243) 157 (0.243) 245 (0.380) 245 (0.380)
Sb Elastic section modulus mm3 (in3) 67 (0.0041) 117 (0.0071) 117 (0.0071) 293 (0.0179) 293 (0.0179) 541.3 (0.033) 541.3 (0.033)
A brg Undercut bearing area6 mm2 (in2) 260 (0.403) 354 (0.549) 354 (0.549) 624 (0.967) 624 (0.967) 707.1 (1.096) 707.1 (1.096)
1 Base material thickness as required to minimize split- 3 Minimum thickness of fastened part as required to 5 Torque tightening of the anchor is not required for
ting as per CSA A23.3-04 Annex D. ensure engagement of full sleeve cross section in proper set. Torque tightening may reduce initial slip
2 Length code in accordance with ICC-ES Acceptance shear. under load and can improve fatigue performance.
Criteria AC193. 4 Metric stop drill bit must be used. See Section 1.4 for 6 Recommended area for calculating maximum bearing
use of matched tolerance diamond core bits. stress in accordance with the CSA A23.3-04 Annex D.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 3
Mechanical Anchoring Systems
4 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 5
Mechanical Anchoring Systems
Given: AN
2 HDA-T M10 anchors under static tension and 1.5h ef
shear loads as shown.
N f = 25 k N
Vf ÊrÊ£ÎÊ
h = 300 mm
h ef
s = 300 mm
h
Slab on grade, f'cÊrÊÓäÊ*>°
ÃÃÕiÊVÀ>Vi`ÊVVÀiÌi°
Condition B per CSA A23.3 D.5.4 c)
Calculate the factored tensile and shear resistance 1.5h ef
1.5h ef c = 200 mm
for this configuration.
A -A
6 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Tension and Shear Interaction Calculations per CSA A23.3-04 Annex D. Code Ref.
-Ìi«Ê£°Ê
iVÊVf ≤ 0.2 Vr
D.8.2.
VfÊÊä°Ó{ΰx®ÊrÊn°ÇÊ ÊÊVf not less than or equal to 0.2 Vr)
-Ìi«ÊÓ°Ê
iVÊNf ≤ 0.2 Nr
D.8.3.
NfÊÊä°Óxx°n®ÊrÊ££°ÓÊ ÊÊNf not less than or equal to 0.2 Nr)
-Ìi«ÊΰÊ
iVÊNfÊÉÊNr + VfÊÉÊVr ≤ 1.2
D.8.4.
ÓxÊÉÊxx°n®Ê³Ê£ÎÊÉÊ{ΰx®ÊrÊä°{{nʳÊä°ÓÊrÊä°Ç{ÇÊÊ£°ÓÊ→ OK
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 7
Mechanical Anchoring Systems
£ÊÀÊÌ
iÀÊVVÀiÌiÊÃÌÀi}Ì
Ã]ÊÕÌ«ÞÊNcbr and Npr by 1 Design strengths in table are for anchors near one edge
corresponding influence of concrete strength factor, fb. only. The values do not apply where the distance to an
edge, measured perpendicular to c1, is less than 1.5c1.
2 The ultimate strength of the anchor steel, futÊrÊnääÊ*>°ÊÀÊ
Shear force is assumed to act perpendicular, towards the
Stainless Steel, multiply Nsr by 0.875.
edge with no eccentricity.
3 Design strengths in the table are based on resistance
ÓÊÀÊÌ
iÀÊVVÀiÌiÊÃÌÀi}Ì
Ã]ÊÕÌ«ÞÊVcbr by corresponding
`vV>ÌÊv>VÌÀÊ,]ÊvÊ-iVÌÊ°x°{°Ê>VÌÀi`ÊÌiÃiÊ
influence of concrete strength factor, fb.
load Nf must be computed from the load combinations
referenced in Clause 8.3.2. Design strengths for concrete ÎÊÀÊÌ
iÊÃ
i>ÀÊÃÌÀi}Ì
ÊÛ>ÕiÃÊvÀÊÌ
iÊ/]ÊÃiiÊ/>LiÊÈ°
LÀi>ÕÌ]ÊNbr, pullout, Npr, and sideface blowout, Nsbr
4 Design strengths in the table are based on resistance
are based on Condition B. Where supplementary
`vV>ÌÊv>VÌÀÊ,]ÊvÊ-iVÌÊ°x°{°Ê>VÌÀi`ÊÃ
i>ÀÊ
reinforcement is provided to satisfy Condition A, design
load Vf must be computed from the load combinations
strengths for Nbr and Nsbr may be increased by the ratio
referenced in Clause 8.3.2. Design strengths for
vÊ, condition A ÊÉÊ, condition B . This increase does not apply to
VVÀiÌiÊLÀi>ÕÌ]ÊVbr, are based on Condition B. Where
pullout strength, Npr.
supplementary reinforcement is provided to satisfy
{Ê7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ Condition A, this design may be increased by the ratio
service load levels (ft < fr) in the region of the anchor, the vÊ, condition AÊÉÊ, condition B . This increase does not apply to
`iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌÊÊÌiÃ]ÊNbr, may pryout capacities, for which condition B is always assumed.
be increased by #c,N (#c,N = 1.25). See Section D.6.2.6.
xÊ7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ
xÊ7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ service load levels (ft < fr) in the region of the anchor, the
service load levels (ft < fr) in the region of the anchor, the `iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌÊÊÃ
i>À]ÊVbr, may be
design strengths for concrete pullout in tension, Npr, may be increased by 40%. See Section D.7.2.7.
increased by 40%. See Section D.6.3.6.
ÈÊ/
iÊ`iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌ]ÊVbr, are based
on the shear load being applied perpendicular towards
the edge. If the load is applied parallel to the edge, the
strengths may be increased 100%. See Section D.7.2.1c.
8 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Minimum
Min. Nsr - Tension
Embedment Edge 1,3,4 Npr - Nsbr - Sideface
Size Concrete Strength of Ncbr - Tension Breakout (kN)
Depth, hef Distance Pullout1,5 Blowout
Thickness, h
cmin Anchor2
M10 100 170 80 31.6 19.2 21.8 29.1 29.1 29.1 29.1 29.1 29.1 29.1 27.9 N/A
M12 125 190 100 46.0 26.8 34.4 40.6 40.6 40.6 40.6 40.6 40.6 34.9 N/A
M16 190 270 150 85.3 X 49.8 59.0 68.8 76.1 76.1 76.1 76.1 69.8 N/A
M20 250 350 200 133.4 X X 75.8 86.2 97.2 108.9 114.9 114.9 104.7 N/A
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22
35 1.32
40 1.41
45 1.50
50 1.58
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 9
Mechanical Anchoring Systems
Nsr - Tension
Spacing, 1,3,4 Npr - Pullout of Nsbgr - Sideface Blowout
Size hef hmin Strength of Ncbgr - Tension Breakout of Group (kN)
s Group1,5 of Group
Anchor Group2
mm mm kN mm c1 - edge distance (mm) kN kN
cmin
80 100 150 200 250 300 350 400 450
100 25.6 29.1 38.8 38.8 38.8 38.8 38.8 38.8 38.8
150 28.7 32.7 43.6 43.6 43.6 43.6 43.6 43.6 43.6
200 31.9 36.3 48.4 48.4 48.4 48.4 48.4 48.4 48.4
250 35.1 40.0 53.3 53.3 53.3 53.3 53.3 53.3 53.3
M10 100 170 63.2 300 38.3 43.6 58.1 58.1 58.1 58.1 58.1 58.1 58.1 55.9 N/A
350 38.3 43.6 58.1 58.1 58.1 58.1 58.1 58.1 58.1
400 38.3 43.6 58.1 58.1 58.1 58.1 58.1 58.1 58.1
450 38.3 43.6 58.1 58.1 58.1 58.1 58.1 58.1 58.1
500 38.3 43.6 58.1 58.1 58.1 58.1 58.1 58.1 58.1
cmin
100 150 200 250 300 350 400 450
100 X X X X X X X X
150 37.5 48.1 56.9 56.9 56.9 56.9 56.9 56.9
200 41.1 52.7 62.3 62.3 62.3 62.3 62.3 62.3
250 44.6 57.3 67.7 67.7 67.7 67.7 67.7 67.7
M12 125 190 92.0 300 48.2 61.9 73.1 73.1 73.1 73.1 73.1 73.1 69.8 N/A
350 51.8 66.4 78.5 78.5 78.5 78.5 78.5 78.5
400 53.6 68.7 81.3 81.3 81.3 81.3 81.3 81.3
450 53.6 68.7 81.3 81.3 81.3 81.3 81.3 81.3
500 53.6 68.7 81.3 81.3 81.3 81.3 81.3 81.3
cmin
150 200 250 300 350 400 450
100 X X X X X X X
150 X X X X X X X
200 67.3 79.7 93.0 102.8 102.8 102.8 102.8
250 71.7 84.9 99.0 109.5 109.5 109.5 109.5
M16 190 270 170.6 300 76.1 90.0 105.0 116.2 116.2 116.2 116.2 139.7 N/A
350 80.4 95.2 111.1 122.9 122.9 122.9 122.9
400 84.8 100.4 117.1 129.6 129.6 129.6 129.6
450 89.2 105.5 123.2 136.2 136.2 136.2 136.2
500 93.6 110.7 129.2 142.9 142.9 142.9 142.9
cmin
200 250 300 350 400 450
100 X X X X X X
150 X X X X X X
200 X X X X X X
250 101.0 114.9 129.6 145.1 153.2 153.2
M20 250 350 266.8 300 106.1 120.7 136.1 152.4 160.9 160.9 209.5 N/A
350 111.1 126.4 142.6 159.7 168.5 168.5
400 116.2 132.1 149.1 166.9 176.2 176.2
450 121.2 137.9 155.5 174.2 183.8 183.8
500 126.3 143.6 162.0 181.4 191.5 191.5
Notes:
A. For eccentric loading, multiply Ncbr by the modification factor for eccentrically loaded anchor groups, ec,N as per Section D.6.2.4.
B. If anchors are affected by more than one edge distance use formulas to calculate Concrete Resistance
f 'c (MPa) fb
20 1.00
25 1.12 s
30 1.22
35 1.32
40 1.41
45 1.50
c1
50 1.58
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
10 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Nsr - Tension
Spacing, 1,3,4 Npr - Pullout of Nsbgr - Sideface Blowout
Size hef hmin Strength of Ncbgr - Tension Breakout of Group (kN)
s Group1,5 of Group
Anchor Group2
mm mm kN mm c1 - edge distance (mm) kN kN
cmin
80 100 150 200 250 300 350 400 450
100 36.7 40.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7
150 47.5 52.3 65.4 65.4 65.4 65.4 65.4 65.4 65.4
200 59.7 65.4 80.7 80.7 80.7 80.7 80.7 80.7 80.7
250 73.3 79.9 97.7 97.7 97.7 97.7 97.7 97.7 97.7
M10 100 170 126.4 300 88.3 95.9 116.3 116.3 116.3 116.3 116.3 116.3 116.3 111.7 N/A
350 88.3 95.9 116.3 116.3 116.3 116.3 116.3 116.3 116.3
400 88.3 95.9 116.3 116.3 116.3 116.3 116.3 116.3 116.3
450 88.3 95.9 116.3 116.3 116.3 116.3 116.3 116.3 116.3
500 88.3 95.9 116.3 116.3 116.3 116.3 116.3 116.3 116.3
cmin
100 150 200 250 300 350 400 450
100 X X X X X X X X
150 57.1 69.5 79.6 79.6 79.6 79.6 79.6 79.6
200 69.6 83.9 95.5 95.5 95.5 95.5 95.5 95.5
250 83.5 99.7 112.8 112.8 112.8 112.8 112.8 112.8
M12 125 190 184.0 300 98.5 116.9 131.6 131.6 131.6 131.6 131.6 131.6 139.7 N/A
350 114.8 135.4 151.8 151.8 151.8 151.8 151.8 151.8
400 123.4 145.1 162.5 162.5 162.5 162.5 162.5 162.5
450 123.4 145.1 162.5 162.5 162.5 162.5 162.5 162.5
500 123.4 145.1 162.5 162.5 162.5 162.5 162.5 162.5
cmin
150 200 250 300 350 400 450
100 X X X X X X X
150 X X X X X X X
200 98.3 112.5 127.7 138.9 138.9 138.9 138.9
250 112.9 128.6 145.3 157.6 157.6 157.6 157.6
M16 190 270 341.2 300 128.5 145.7 164.0 177.4 177.4 177.4 177.4 279.3 N/A
350 145.2 163.9 183.8 198.3 198.3 198.3 198.3
400 162.8 183.2 204.7 220.5 220.5 220.5 220.5
450 181.5 203.5 226.7 243.8 243.8 243.8 243.8
500 201.1 224.9 249.9 268.3 268.3 268.3 268.3
cmin
200 250 300 350 400 450
100 X X X X X X
150 X X X X X X
200 X X X X X X
250 144.9 160.9 177.6 195.2 204.3 204.3
M20 250 350 533.6 300 161.4 178.6 196.6 215.5 225.2 225.2 419.0 N/A
350 178.8 197.2 216.5 236.7 247.2 247.2
400 197.0 216.7 237.4 259.0 270.2 270.2
450 216.1 237.2 259.2 282.3 294.2 294.2
500 236.1 258.5 282.0 306.5 319.2 319.2
Notes:
A. For eccentric loading, multiply Ncbr by the modification factor for eccentrically loaded anchor groups, ec,N as per Section D.6.2.4.
B. If anchors are affected by more than one edge distance use formulas to calculate Concrete Resistance
f 'c (MPa) fb
20 1.00
25 1.12 s
30 1.22
35 1.32
40 1.41
45 1.50
c1 s
50 1.58
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 11
Mechanical Anchoring Systems
Nsr - Tension
Spacing, 1,3,4 Npr - Pullout of Nsbgr - Sideface Blowout
Size hef hmin Strength of Ncbgr - Tension Breakout of Group (kN)
s Group1,5 of Group
Anchor Group2
mm mm kN mm c1 - edge distance (mm) kN kN
cmin
80 100 150 200 250 300 350 400 450
100 45.8 50.9 64.6 64.6 64.6 64.6 64.6 64.6 64.6
150 63.3 69.8 87.2 87.2 87.2 87.2 87.2 87.2 87.2
200 83.6 91.6 113.0 113.0 113.0 113.0 113.0 113.0 113.0
250 106.7 116.3 142.1 142.1 142.1 142.1 142.1 142.1 142.1
M10 100 170 189.6 300 132.5 143.9 174.4 174.4 174.4 174.4 174.4 174.4 174.4 167.6 N/A
350 139.9 151.9 174.4 174.4 174.4 174.4 174.4 174.4 174.4
400 147.2 157.0 174.4 174.4 174.4 174.4 174.4 174.4 174.4
450 150.0 157.0 174.4 174.4 174.4 174.4 174.4 174.4 174.4
500 150.0 157.0 174.4 174.4 174.4 174.4 174.4 174.4 174.4
cmin
100 150 200 250 300 350 400 450
100 X X X X X X X X
150 73.4 89.4 102.4 102.4 102.4 102.4 102.4 102.4
200 93.9 113.1 128.7 128.7 128.7 128.7 128.7 128.7
250 116.8 139.6 158.0 158.0 158.0 158.0 158.0 158.0
M12 125 190 276.0 300 142.3 168.8 190.1 190.1 190.1 190.1 190.1 190.1 209.5 N/A
350 170.3 200.7 225.2 225.2 225.2 225.2 225.2 225.2
400 189.3 222.5 243.8 243.8 243.8 243.8 243.8 243.8
450 197.5 229.1 243.8 243.8 243.8 243.8 243.8 243.8
500 205.7 229.1 243.8 243.8 243.8 243.8 243.8 243.8
cmin
150 200 250 300 350 400 450
100 X X X X X X X
150 X X X X X X X
200 123.8 141.8 160.9 175.0 175.0 175.0 175.0
250 147.3 167.8 189.6 205.6 205.6 205.6 205.6
M16 190 270 511.8 300 172.9 196.0 220.5 238.5 238.5 238.5 238.5 419.0 N/A
350 200.4 226.3 253.7 273.8 273.8 273.8 273.8
400 230.0 258.7 289.1 311.4 311.4 311.4 311.4
450 261.5 293.2 326.8 351.3 351.3 351.3 351.3
500 295.1 329.9 366.7 393.6 393.6 393.6 393.6
cmin
200 250 300 350 400 450
100 X X X X X X
150 X X X X X X
200 X X X X X X
250 181.2 201.1 222.0 244.0 255.3 255.3
M20 250 350 800.4 300 207.5 229.6 252.7 277.0 289.6 289.6 628.4 N/A
350 235.6 259.9 285.4 312.0 325.8 325.8
400 265.5 292.1 320.0 349.1 364.1 364.1
450 297.1 326.1 356.4 388.1 404.5 404.5
500 330.5 362.0 394.8 429.2 446.9 446.9
Notes:
A. For eccentric loading, multiply Ncbr by the modification factor for eccentrically loaded anchor groups, ec,N as per Section D.6.2.4.
B. If anchors are affected by more than one edge distance use formulas to calculate Concrete Resistance
f 'c (MPa) fb
20 1.00
s
25 1.12
30 1.22
35 1.32
40 1.41
s
45 1.50
50 1.58
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn° c1 s
12 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12 V
30 1.22
35 1.32
40 1.41
45 1.50 c1
50 1.58
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 13
Mechanical Anchoring Systems
Steel
Steel
Strength in
Strength in
Anchor Designation Thickness of fastened part(s) Shear,
Shear,
Seismic
Static (kN)b a,b
(kN)
Carbon Steel Anchors mm in. Vsr Vsr, seismic
10 ≤ t < 15 3/8 ≤ t < 5/8 39.5 35.7
HDA-T 20-M10x100
15 ≤ t < 20 5/8 ≤ t < 13/16 44.6 40.2
10 ≤ t < 15 3/8 ≤ t < 5/8 47.2 42.7
HDA-T 22-M12x125
15 ≤ t < 50 5/8 ≤ t < 2 52.9 47.2
15 ≤ t < 20 5/8 ≤ t < 13/16 86.7 77.8
20 ≤ t < 25 13/16 ≤ t < 1 98.2 88.6
HDA-T 30-M16x190
25 ≤ t < 30 1 ≤ t < 1-3/16 108.4 97.5
30 ≤ t < 60 1-3/16 ≤ t < 2-3/8 117.3 105.2
20 ≤ t < 35 13/16 ≤ t < 1-3/8 128.1 115.4
HDA-T 37-M20x250 35 ≤ t < 50 1-3/8 ≤ t < 2 144.1 129.4
50 ≤ t < 100 2≤t<4 154.9 139.6
a. The nominal steel strength Vsr, seismic for the HDA-P shall be taken from the HDA Design Information Table
b. For groups of anchors, multiply value by number of anchors, n
14 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 15
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
16 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 17
Mechanical Anchoring Systems
18 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s s
35 1.32
40 1.41 V V
45 1.50
50 1.58 s s
55 1.66
c1 c1 s
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 19
Mechanical Anchoring Systems
Vsgr - Shear Strength of Vsgr - Shear Strength of Concrete 1,2,4,5,6,7 Vcpgr - Pryout
Size hef 3 Spacing, s Vcbgr - Shear Breakout (kN)
Anchor (kN) Anchor (kN)3 Thickness, h Resistance
c1 c1 s
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
20 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
c1 c1 s
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 21
Mechanical Anchoring Systems
Table 14 - Factored resistance for 3 or 6 HDA anchors subject to Shear Loads in Cracked Concrete (f'c = 20 MPa)
f'c (MPa) fb
20 1.00
25 1.12 s
30 1.22 s
35 1.32
40 1.41
V V
45 1.50 s s
50 1.58
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊn°
22 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
1. Drill a hole to the required depth using a stop drill bit 2. Clean hole with compressed air or a hand air pump 3. Insert the anchor into the hole by hand, so that the
matched to the anchor, (refer to specification table such that drilling debris is evacuated. cone sits on the bottom of the drilled hole. Do not
and ordering info.). If rebar is encountered, use a Hilti remove the plastic cap which protects the threaded
metric matched tolerance diamond core bit to drill rod. Using the assigned setting tool and Hilti hammer
through the rebar. Remove the concrete core and drill, the setting tool is guided over the anchor rod
finish drilling the hole with the stop drill bit. Always and engages the grooves in the sleeve. It is critical
consult with the Engineer of Record before cutting to use the specified Hilti hammer drills.
rebar.
4. The anchor is set with the specified 5. The anchor is correctly set and the 6. Remove the plastic thread protector cap. Secure the
Hilti hammer drill in hammer drill mode undercut is fully formed when the red part to be fastened by using the conical spring wash-
and in the specified gear. During the setting mark on the anchor bolt is visible above the er and nut provided. Apply a torque not to exceed
procedure, both drilling and impact energy are top edge of the sleeve. The top edge of the the maximum values given in the Specification Table.
transferred to the sleeve by the setting tool, causing anchor sleeve must be positioned approx. 3mm Torque is not required to set the anchor.
the sleeve to slide over the conical end of the anchor below the concrete surface. If the anchor setting time
bolt while forming the undercut in the base material. exceeds 60 seconds for M10, M12 or M16 anchors
On the setting tool, the red ring indicates the progress or 120 seconds for M20 anchors the installation
of the setting operation. When this marking is flush failed and the anchors must not be loaded.
with the concrete surface, check the anchor for
proper setting (refer to step 5).
1. Drill a hole to the required depth using a stop drill bit 2. Clean hole with compressed air or a hand air pump 3. Insert the anchor into the hole by hand, so that the
matched to the anchor, (refer to specification table such that drilling debris is evacuated. cone sits on the bottom of the drilled hole. Do not
and ordering info.). If rebar is encountered, use a Hilti remove the plastic cap which protects the threaded
metric matched tolerance diamond core bit to drill rod. Using the assigned setting tool and Hilti hammer
through the rebar. Remove the concrete core and fin- drill, the setting tool is guided over the anchor rod
ish drilling the hole with the stop drill bit. Always con- and engages the grooves in the sleeve. It is critical
sult with the Engineer of Record before cutting rebar. to use the specified Hilti hammer drills.
4. The anchor is set with the specified 5. The anchor is set and the 6. Remove the plastic thread protector cap. Secure the
Hiltli hammer drill in hammer drill undercut is fully formed when the part to be fastened by using the conical spring wash-
mode and in the specified gear. During red marking on the anchor bolt is visible er and nut provided. Apply a torque not to exceed
the setting procedure, both drilling and above the top edge of the sleeve. The top the maximum values given in the Specification Table.
impact energy are transferred to the sleeve by edge of the anchor sleeve must be positioned Torque is not required to set the anchor.
the setting tool, causing the sleeve to slide over approx. 3mm below the surface of the fixture. If
the conical end of the anchor bolt while forming the anchor setting time exceeds 60 seconds for M10,
undercut in the base material. On the setting tool, M12 or M16 anchors or 120 seconds for M20
the red ring indicates the progress of the setting anchors the installation failed and the anchor
operation. When this marking is flush with the con- must not be loaded.
nected part, check the anchor for proper setting (refer
to step 5).
The HDA Undercut Anchor, designed to carry significant, safety-relevant loads, must be installed correctly with the prescribed tools
to function properly. Carefully follow all instructions located inside the box. Installer training is also available upon request.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 23
Mechanical Anchoring Systems
24 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
HDA-T Anchor
HDA-T HDA-T F HDA-T R HDA HDA-T Anchor Stop Drill Bit Diamond Core Bit Setting Tool
Anchor (mm)
Item No. Item No. Item No. Box dia x min.emb/max. Description (mm)
Galvanized Sherardised 316 Stainless Qty thickness fastened Item No. dia. x drill depth Diameter Item No. Description
332090 TE-C-B20x120 331843 TE-C-ST-M10
331545 339361 339351 12 HDA-T M10x100/20 20mm (25/32”)
237450 TE-Y-B20x120 287133 TE-Y-ST-M10
332092 TE-C-B22x155 331844 TE-C-ST-M13
331548 339362 339352 8 HDA-T M12x125/30 22mm (7/8”)
237452 TE-Y-B22x155 287134 TE-Y-ST-M12
331549 339363 339353 8 HDA-T M12x125/50 332093 TE-C-B22x175 22mm (7/8”) 331844 TE-C-ST-M12
331552 339364 339354 4 HDA-T M16x190/40 332098 TE-Y-B30x230 30mm (1-1/8”) 331846 TE-Y-ST-M16
331553 339365 339355 4 HDA-T M16x190/60 332099 TE-Y-B30x250 30mm (1-1/8”) 331846 TE-Y-ST-M16
339267 – – 2 HDA-T M20x250/50 339271 TE-Y-B37x300 37mm (1-3/8”) 339269 TE-Y-ST-M20
339268 – – 2 HDA-T M20x250/100 339272 TE-Y-B37x350 37mm (1-3/8”) 339269 TE-Y-ST-M20
HDA-P Anchor
HDA-P HDA-P F HDA-P R HDA HDA-P Anchor Stop Drill Bit Diamond Core Bit Setting Tool
Anchor (mm)
Item No. Item No. Item No. Box dia x min.emb/max. Description (mm)
Galvanized Sherardised 316 Stainless Qty thickness fastened Item No. dia. x drill depth Diameter Item No. Description
332089 TE-C-B20x100 331843 TE-C-ST-M10
331544 339356 339346 12 HDA-P M10x100/20 20mm (25/32”)
237449 TE-Y-B20x100 287133 TE-Y-ST-M10
331091 TE-C-B22x125 331844 TE-C-ST-M13
331546 339357 339347 8 HDA-P M12x125/30 22mm (7/8”)
237451 TE-Y-B22x125 287134 TE-Y-ST-M13
331547 339358 339348 8 HDA-P M12x125/50 332091 TE-C-B22x125 22mm (7/8”) 331844 TE-C-ST-M12
331550 339359 339349 4 HDA-P M16x190/40 332097 TE-Y-B30x190 30mm (1-1/8”) 331846 TE-Y-ST-M16
331551 339360 339350 4 HDA-P M16x190/60 332097 TE-Y-B30x190 30mm (1-1/8”) 331846 TE-Y-ST-M16
339265 – – 2 HDA-P M20x250/50 339270 TE-Y-B37x250 37mm (1-3/8”) 339269 TE-Y-ST-M20
339266 – – 2 HDA-P M20x250/100 339270 TE-Y-B37x250 37mm (1-3/8”) 339269 TE-Y-ST-M20
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 25
Mechanical Anchoring Systems
Removal Instructions
TE-C
HDA-P HDA-T
1. Remove the nut and washer 2. Push back the grip (against 4. Insert the adapter (drive) into 5. Put adapter (drive) onto 8. To return the tool to its start-
from the threaded rod, (also this spring pressure). the drill chuck and lock the threaded spindle of the ing position, put the adapter
remove fastening part for 3. Allow the two drive lugs to (TE 25 recommended). removal tool and switch (drive) on the other end of
HDA-P applications). engage the groove in the Important: on the drill. the threaded spindle.
anchor sleeve using a slight s Switch off the hammer- 6. The anchor sleeve will be 9. Switch on the hammer
twisting movement of the ing action (the removal extracted. drill until the adapter stop
grip. Release the grip. tool will be permanently 7. Disengage the drive lugs reaches the removal tool.
damaged if this step from the groove by lifting
is neglected.). up and twisting the grip.
s Use low speed
(setting 1 for the TE 25).
Applicable
26 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
HSL-3 Heavy Duty Anchor HSL-3-B Heavy Duty Anchor 2.4 Installation Instructions
with Torque Cap
2.5 Ordering Information
Red Setting Indicator
/
ÀiiÊ>VVÕÀ>ÌiÞÊÃâi`Ê
-ÎÊi>ÛÞÊÕÌÞÊV
ÀÊ shear pins are provided in
ÜÌ
Ê/
Ài>`i`Ê,` the red indicator cap. As
the required installation
Maximum fastened torque (Tinst) is reached the
Metric Ì
ViÃÃÊ® red indicator cap shears off. A green seal on
the bolt head appears which indicates that
HSL-3-G M 12/25 the anchor has been set properly.
Heavy duty L>LÌ Metric thread Example: HSL-3-G M12/25 Bolt
Sleeve ÊÃÌÕ` ÃâiÊ®ÆÊÌÊ /
ÃÊÃÊ>Ê-ÎÊÃÌÕ`Ê>V
À°Ê/
iÊÌ
Ài>`ÊÃâiÊ
(Expansion) B torque cap hole diameter is 12 mm and this anchor can attach up to a Washer
Anchor ÓxÊÊÌ
VÊ«>Ìi
UÊ }
Ê>`ÊV>«>VÌÞ
Expansion
UÊ ÀViVÌÀi`ÊiÝ«>ÃÊÜ
V
Ê Sleeve
allows for follow-up expansion
UÊ ,i>LiÊV>«}ÊvÊ«>ÀÌÊv>ÃÌii`Ê Cone
to overcome gaps
>ÀLÊ-ÌiiÊ7>Ã
iÀÊVvÀÃÊÌÊ Ê£x{{]ÊÀ>`iÊ-ÌÎÇ]ÊvuÊÊ£ääÊÃ
Carbon Steel Expansion Cone conforms to DIN 1654-4, fuÊÊnäÊÃ
Carbon Steel Expansion Sleeve (M8-M16) conforms to DIN 10139 and (M20-M24)
conforms to DIN 2393-2
Carbon Steel Spacing Sleeve conforms to DIN 2393 T1, fuÊÊ£ääÊÃ
>«ÃLiÊ-iiÛiÊÃÊ>`iÊvÀÊ>ViÌ>Ê«ÞÝÞiÌ ÞiiÊ*"®ÊÀiÃ
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 27
Mechanical Anchoring Systems
dw
dh t
h nom
ho
h
d bit
28 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 29
Mechanical Anchoring Systems
Given: AN
(2) HSL-3 M10 anchors under static tension load as shown. t
1.5h ef
h e f = 70 mm
Slab on grade, f ' cÊrÊÓäÊ*>°
No supplementary reinforcing.
ÃÃÕiÊÕVÀ>Vi`ÊVVÀiÌi° h ef
Condition B per CSA A23.3 D.5.4 c h s = 150 mm
Calculate the factored tensile resistance for this configuration.
1.5h ef
1.5h ef c = 100 mm
Calculation per CSA A23.3 Annex D and this report. Code Ref.
Step 1. Calculate factored steel resistance of anchor in tension
N sr = nA se F s f u t ,ÊrÊÓÊÝÊxn°£ÊÝÊä°nxÊÝÊnääÊÝÊä°nÊrÊÈΰÓÊ Ê °È°£°Ó
-Ìi«ÊÓ°Ê
>VÕ>ÌiÊv>VÌÀi`ÊVVÀiÌiÊLÀi>ÕÌÊÃÌÀi}Ì
ÊvÊ>V
ÀÊÊÌiÃÊ
N cbgr = (ANÉNo) #ec,N #ed,N #c,N #cp,N Nbr D.6.2.1
-Ìi«ÊΰÊ6iÀvÞÊÕÊVVÀiÌiÊÌ
ViÃÃ]ÊÕÊë>V}Ê>`Êi`}iÊ`ÃÌ>Vi\
hminÊrÊ£{äÊÊÊ£xäÊÆÊ
sminÊrÊÇäÊÊÊ£xäÊÆÊ
cminÊrÊÇäÊÊÊ£ääÊÆÊ
sdesign > 456 – (3.09 x c design) or s minÆÊÊÃViÊÃ design = 150 mm ≥ 147 mm or 70 mm D.9
Step 3a. Calculate ANo and ANÊvÀÊÌ
iÊ>V
À>}i\Ê
ANO = 9 h e f 2 = 9 x (70)2 = 44,100 mm2
AN = (1.5h e f + c)(3h e f + s) = [1.5 x (70) + 100][3 x (70) + 150] = 73,800 mm2 < 2 ANOÆÊÊ °È°Ó°£
Step 3b. Calculate modification factor for eccentrically loaded anchors groups #ec,N' = 1; no eccentricity D.6.2.4
Step 3c. Calculate N br \
N b r = k F c (f' c ) 0. 5 h e f 1. 5 R = 10 x 0.65 x 200.5 x 701.5ÊÝÊ£°ääÊrʣǰäÓÊ Ê °È°Ó°Ó
-Ìi«ÊÎ`°Ê
>VÕ>ÌiÊ`wV>ÌÊv>VÌÀÊvÀÊi`}iÊivviVÌÃ\Ê#ed,N = 0.7 + 0.3(c m i n ÉÊ£°xh e f ) = 0.986 D.6.2.5
Step 3e. #c,N = 1.0 D.6.2.6
-Ìi«ÊÎv°Ê
>VÕ>ÌiÊ`wV>ÌÊv>VÌÀÊvÀÊëÌÌ}\Ê
#cp,N = max [c a ,m i n ÊÉÊV ac ; 1.5h ef ÊÉÊV ac RÊrÊ>ÝÊQ£ääÉ££äÊÆÊ£°xÊÇä®ÊÉÊ££äRÊrÊä°xxÊ °È°Ó°Ç
Step 3g. Calculate N cbg r\ÊÊN cbg r ÊrÊÇÎnääÊÉÊ{{£ää®ÊÝÊ£ÊÝÊä°nÈÊÝÊ£ÊÝÊä°xxÊÝʣǰäÓÊrÊÓÈ°nÊ Ê °È°Ó°£
-Ìi«Ê{°Ê
iVÊv>VÌÀi`Ê«ÕÕÌÊÀiÃÃÌ>Vi\ÊÃiiÊ-ÎÊiÃ}ÊvÀ>ÌÊ/>Li]ÊN p ,unc r does not govern. D.6.3.1
-Ìi«Êx°Ê
ÌÀ}Êv>VÌÀi`ÊÌiÃiÊÀiÃÃÌ>Vi\ÊN cbg r ÊrÊÓÈ°nÊ Ê
30 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
£ÊÀÊÌ
iÀÊVVÀiÌiÊÃÌÀi}Ì
Ã]ÊÕÌ«ÞÊNcbr and Npr by 1 Design strengths in table are for anchors near one edge
corresponding influence of concrete strength factor, fb. only. The values do not apply where the distance to an
edge, measured perpendicular to c1, is less than 1.5c1.
2 The ultimate strength of the anchor steel, futÊrÊnääÊ*>°
Shear force is assumed to act perpendicular, towards the
3 Design strengths in the table are based on resistance edge with no eccentricity.
`vV>ÌÊv>VÌÀÊ,]ÊvÊ-iVÌÊ°x°{°Ê>VÌÀi`ÊÌiÃiÊ
ÓÊÀÊÌ
iÀÊVVÀiÌiÊÃÌÀi}Ì
Ã]ÊÕÌ«ÞÊVcbr by corresponding
load Nf must be computed from the load combinations
influence of concrete strength factor, fb.
referenced in Clause 8.3.2. Design strengths for concrete
LÀi>ÕÌ]ÊNbr, pullout, Npr, and sideface blowout, Nsbr 3 The ultimate strength of the anchor steel, futÊrÊnääÊ*>°
are based on Condition B. Where supplementary
4 Design strengths in the table are based on resistance
reinforcement is provided to satisfy Condition A, design
`vV>ÌÊv>VÌÀÊ,]ÊvÊ-iVÌÊ°x°{°Ê>VÌÀi`ÊÃ
i>ÀÊ
strengths for Nbr and Nsbr may be increased by the ratio
load Vf must be computed from the load combinations
vÊ, condition A ÊÉÊ, condition B . This increase does not apply to
referenced in Clause 8.3.2. Design strengths for
pullout strength, Npr.
VVÀiÌiÊLÀi>ÕÌ]ÊVbr, are based on Condition B. Where
{Ê7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ supplementary reinforcement is provided to satisfy
service load levels (ft < fr) in the region of the anchor, the Condition A, this design may be increased by the ratio of
`iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌÊÊÌiÃ]ÊNbr, may ,condition AÊÉÊ,condition B. This increase does not apply to pryout
be increased by #c,N (#c,N = 1.4 for M8 and 1.0 for all other capacities, for which condition B is always assumed.
Ãâiî°Ê-iiÊ-iVÌÊ°È°Ó°È°
xÊ7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ
xÊ7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ service load levels (ft < fr) in the region of the anchor, the
service load levels (ft < fr) in the region of the anchor, the `iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌÊÊÃ
i>À]ÊVbr, may
design strengths for concrete pullout in tension, Npr, may be be increased by 40%. See Section D.7.2.7.
increased by 40%. See Section D.6.3.6.
ÈÊ/
iÊ`iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌ]ÊVbr, are based
6 Stainless steel HSL anchors are not applicable to the on the shear load being applied perpendicular towards
-ÊÓΰÎä{ÊiÝÊÊ`iÃ}ÊiÌ
`°ÊÊÀÊ>««V>ÌÃÊ the edge. If the load is applied parallel to the edge, the
ÀiµÕÀ}ÊÃÌ>iÃÃÊÃÌiiÊ>V
ÀÃ]ÊVÃ`iÀÊ*,]Ê strengths may be increased 100%. See Section D.7.2.1c.
/,ÊÀÊ ,/<ÊÊÌ
ÃÊÃÕ««iiÌ°
7 Linear interpolation for intermediate values of edge
distance, c1 is permissible.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 31
Mechanical Anchoring Systems
Minimum
Min. Nsr - Tension
Embedment Edge 1,3,4 Npr - Nsbr - Sideface
Size Concrete Strength of Ncbr - Tension Breakout (kN)
Depth, hef Distance Pullout1,5 Blowout
Thickness, h
cmin Anchor2
M8 60 120 60 20.0 7.1 9.5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 8.7 N/A
M10 70 140 70 31.6 12.8 16.4 17.0 17.0 17.0 17.0 17.0 17.0 17.0 1 4.0 N/A
M12 80 160 90 46.0 16.8 18.1 20.8 20.8 20.8 20.8 20.8 20.8 20.8 N/A N/A
M16 100 200 120 85.3 24.6 X 29.1 29.1 29.1 29.1 29.1 29.1 29.1 N/ A N/A
M20 125 250 125 133.3 30.5 X 34.4 40.6 40.6 40.6 40.6 40.6 40.6 N /A N/A
M24 150 300 150 191.9 40.1 X 40.1 48.8 53.4 53.4 53.4 53.4 53.4 N /A N/A
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22
35 1.32
40 1.41
45 1.50
50 1.58 c1
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
32 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 33
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
34 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ° c1 s
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 35
Mechanical Anchoring Systems
f'c (MPa) fb
20 1.00
25 1.12 V
30 1.22
35 1.32
40 1.41
45 1.50
50 1.58 c1
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
36 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Vsgr - Shear Strength of Vsgr - Shear Strength of Concrete 1,2,4,5,6,7 Vcpgr - Pryout
Size hef Spacing, s Vcbgr - Shear Breakout (kN)
Anchor (kN)3 Anchor (kN)
3
Thickness, h Resistance
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 37
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
38 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Vsgr - Shear Strength of Vsgr - Shear Strength of Concrete 1,2,4,5,6,7 Vcpgr - Pryout
Size hef Spacing, s Vcbgr - Shear Breakout (kN)
Anchor (kN)3 Anchor (kN)3 Thickness, h Resistance
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 39
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
40 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 41
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
42 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
c1 c1 s
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 43
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
c1 c1 s
44 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
c1 c1 s
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 45
Mechanical Anchoring Systems
Vsgr - Shear Strength of Vsgr - Shear Strength of Concrete 1,2,4,5,6,7 Vcpgr - Pryout
Size hef Spacing, s Vcbgr - Shear Breakout (kN)
Anchor (kN)3 Anchor (kN)
3
Thickness, h Resistance
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
c1 c1 s
46 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Vsgr - Shear Strength of Vsgr - Shear Strength of Concrete 1,2,4,5,6,7 Vcpgr - Pryout
Size hef Spacing, s Vcbgr - Shear Breakout (kN)
Anchor (kN)3 Anchor (kN)
3
Thickness, h Resistance
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
c1 c1 s
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 47
Mechanical Anchoring Systems
Vsgr - Shear Strength of Vsgr - Shear Strength of Concrete 1,2,4,5,6,7 Vcpgr - Pryout
Size hef Spacing, s Vcbgr - Shear Breakout (kN)
Anchor (kN)3 Anchor (kN)
3
Thickness, h Resistance
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊΣ°
c1 c1 s
48 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
3. Using a hammer, tap the anchor through 4. Using a torque wrench, apply the speci-
the part being fastened into the drilled fied installation torque. HSL-3-B does not
hole until the washer is in contact with require use of a torque wrench. Tighten
the fastened part. Do not expand anchor until torque cap shears off.
by hand prior to installation.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 49
Mechanical Anchoring Systems
Expansion Cone
Listings/Approvals
ICC-ES (International Code Council)
-,££ÇÊ
FM (Factory Mutual)
*«iÊ>}iÀÊ
«iÌÃÊvÀÊÕÌ>ÌVÊ
-«ÀiÀÊ-ÞÃÌiÃÊÎÉn»ÊÊÎÉ{»®
UL (Underwriters Laboratories)
*«iÊ>}iÀÊ
µÕ«iÌÊvÀÊÀiÊ
*ÀÌiVÌÊ-iÀÛViÃÊÎÉn»ÊÊÎÉ{»®
50 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Ê ÎÉnÊÊ Ê ÈÇ{{
Ê £ÉÓÊ Ç{£Ê ££Ó{ä
Ê xÉnÊ ££{ÈxÊ £ÇxÎx
Ê ÎÉ{Ê £ÇxÎxÊ ÓxnxÎ
UÊ
>ÀLÊÃÌiiÊ>V
ÀÊV«iÌÃÊ«>Ìi`ÊÊ>VVÀ`>ViÊÜÌ
Ê-/Ê ÊÈÎÎÊÌÊ>ÊÕÊÌ
ViÃÃÊvÊx°
UÊ ÕÌÃÊVvÀÊÌÊÌ
iÊÀiµÕÀiiÌÃÊvÊ-/ÊÊxÈÎ]ÊÀ>`iÊ]ÊiÝ°Ê
UÊ 7>Ã
iÀÃÊiiÌÊÌ
iÊÀiµÕÀiiÌÃÊvÊ-/ÊÊn{{°Ê
UÊ
Ý«>ÃÊÃiiÛiÃÊÜi`}iîÊ>ÀiÊ>Õv>VÌÕÀi`ÊvÀÊ-ÊΣÈÊÃÌ>iÃÃÊÃÌii°Ê
Stainless steel
1
UÊ -Ì>iÃÃÊÃÌiiÊ /<Ê>V
ÀÃÊ>ÀiÊ>`iÊvÊ-ÊÎä{Ê>ÌiÀ>Ê>`Ê
>ÛiÊÌ
iÊvÜ}ÊÕÊLÌÊvÀ>VÌÕÀiÊ>`Ã
UÊ ÕÌÃÊiiÌÊÌ
iÊ`iÃ>ÊÀiµÕÀiiÌÃÊvÊ-/ÊÊx{°
UÊ 7>Ã
iÀÃÊiiÌÊÌ
iÊ`iÃ>ÊÀiµÕÀiiÌÃÊvÊ -Ê £n°ÓÓ°£]Ê/Þ«iÊ]Ê«>°
UÊ
Ý«>ÃÊ-iiÛiÊ>ÀiÊ>`iÊvÀÊ-ÊΣȰ
UÊ ÊÕÌÃÊ>`ÊÜ>Ã
iÀÃÊ>ÀiÊ>`iÊvÀÊ-ÊÎä{ÊÃÌ>iÃÃÊÃÌii°Ê
1 Bolt fracture loads are determined by testing in jig as part of product QC. These loads are not intended for design purposes. See Tables 2 and 3.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 51
Mechanical Anchoring Systems
52 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 53
Mechanical Anchoring Systems
54 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
h min
c a, min at s ≥
s design
s min at c ≥
h ≥ h min
c design
edge distance c
Table 4 — Mean Axial Stiffness Values (1000 lb/in.) for Kwik Bolt TZ Carbon
and Stainless Steel Anchors in Normal-Weight Concrete1
Concrete condition carbon steel KB-TZ, all diameters stainless steel KB-TZ, all diameters
Ê ÕVÀ>Vi`ÊVVÀiÌiÊ ÇääÊ £Óä
Ê VÀ>Vi`ÊVVÀiÌiÊ xääÊ ä
1 Mean values shown. Actual stiffness may vary considerably depending on concrete strength, loading and geometry of application.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 55
Mechanical Anchoring Systems
Length ID marking Ê Ê
Ê Ê
Ê Ê Ê Ê Ê Ê Ê Ê Ê Ê "Ê *Ê +Ê ,Ê -Ê /Ê 1Ê 6Ê 7
on bolt head
Length of From 11⁄2 2 21⁄2 3 31⁄2 4 41⁄2 5 51⁄2 6 61⁄2 7 71⁄2 8 81⁄2 9 91⁄2 10 11 12 13 14 15
anchor, Up to but
anch (in.) not 2 21⁄2 3 31⁄2 4 41⁄2 5 51⁄2 6 61⁄2 7 71⁄2 8 81⁄2 9 91⁄2 10 11 12 13 14 15 16
including
Figure 4 — Bolt Head with Length Identification Mark and Kwik Bolt TZ Head Notch Embossment
56 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
£ÊÀÊÌ
iÀÊVVÀiÌiÊÃÌÀi}Ì
Ã]ÊÕÌ«ÞÊNcbr and Npr by 1 Design strengths in table are for anchors near one edge
corresponding influence of concrete strength factor, fb. only. The values do not apply where the distance to an
edge, measured perpendicular to c1, is less than 1.5c1.
ÓÊÀÊ-Ì>iÃÃÊ-Ìii]ÊÕÃiÊ ,/<ÊÌ>Lið
Shear force is assumed to act perpendicular, towards the
3 Design strengths in the table are based on resistance edge with no eccentricity.
`vV>ÌÊv>VÌÀÊ,]ÊvÊ-iVÌÊ°x°{°Ê>VÌÀi`ÊÌiÃiÊ
ÓÊÀÊÌ
iÀÊVVÀiÌiÊÃÌÀi}Ì
Ã]ÊÕÌ«ÞÊVcbr by corresponding
load Nf must be computed from the load combinations
influence of concrete strength factor, fb.
referenced in Clause 8.3.2. Design strengths for concrete
LÀi>ÕÌ]ÊNbr, pullout, Npr, and sideface blowout, Nsbr ÎÊÀÊ-Ì>iÃÃÊ-Ìii]ÊÕÃiÊ ,/<ÊÌ>Lið
are based on Condition B. Where supplementary
4 Design strengths in the table are based on resistance
reinforcement is provided to satisfy Condition A, design
`vV>ÌÊv>VÌÀÊ,]ÊvÊ-iVÌÊ°x°{°Ê>VÌÀi`ÊÃ
i>ÀÊ
strengths for Nbr and Nsbr may be increased by the ratio
load Vf must be computed from the load combinations
vÊ, condition A ÊÉÊ, condition B . This increase does not apply to
referenced in Clause 8.3.2. Design strengths for
pullout strength, Npr.
VVÀiÌiÊLÀi>ÕÌ]ÊVbr, are based on Condition B. Where
{Ê7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ supplementary reinforcement is provided to satisfy
service load levels (ft < fr) in the region of the anchor, the Condition A, this design may be increased by the ratio
`iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌÊÊÌiÃ]ÊNbr, may vÊ, condition AÊÉÊ, condition B . This increase does not apply to
be increased by #c,N. See Section D.6.2.6. pryout capacities, for which condition B is always assumed.
xÊ7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ xÊ7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ
service load levels (ft < fr) in the region of the anchor, the service load levels (ft < fr) in the region of the anchor, the
design strengths for concrete pullout in tension, Npr, may be `iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌÊÊÃ
i>À]ÊVbr, may be
increased by 40%. See Section D.6.3.6. increased by 40%. See Section D.7.2.7.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 57
Mechanical Anchoring Systems
Minimum
Min. Nsr - Tension
Embedment Edge 1,3,4 Npr - Nsbr - Sideface
Size Concrete Strength of Ncbr - Tension Breakout (kN)
Depth, hef Distance Pullout1,5 Blowout
Thickness, h
cmin Anchor2
3/8 (2) 51 127 64 19.7 6.5 7.4 7.4 7.4 7.4 7.4 7.4 7.4 7.4 7.1 N/A
1/2 (2) 51 152 70 32.3 6.9 7.4 7.4 7.4 7.4 7.4 7.4 7.4 7.4 N/A N/A
1/2 (3-1/4) 83 203 60 32.3 9.6 13.1 15.4 15.4 15.4 15.4 15.4 15.4 15.4 15.3 N/A
5/8 (3-1/8) 79 127 92 52.0 11.8 12.6 14.3 14.3 14.3 14.3 14.3 14.3 14.3 N/A N/A
5/8 (4) 102 203 83 52.0 13.9 15.5 20.6 21.0 21.0 21.0 21.0 21.0 21.0 N/A N/A
3/4 (3-3/4) 95 203 121 76.0 16.6 X 18.8 18.8 18.8 18.8 18.8 18.8 18.8 N/A N/A
3/4 (4-3/4) 121 203 105 76.0 18.7 X 23.4 27.1 27.1 27.1 27.1 27.1 27.1 N/A N/A
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22
35 1.32
40 1.41
45 1.50
50 1.58 c1
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
58 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Nsr - Tension
Spacing, Npr - Pullout of Nsbgr - Sideface Blowout
Size hef hmin Strength of Anchor Ncbgr - Tension Breakout of Group1,3,4 (kN)
s Group1,5 of Group
Group2
mm mm kN mm c1 - edge distance (mm) kN kN
cmin
64 100 150 200 250 300 350 400 450
100 X 12.3 12.3 12.3 12.3 12.3 12.3 12.3 12.3
150 12.8 14.7 14.7 14.7 14.7 14.7 14.7 14.7 14.7
200 12.9 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
250 12.9 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
3/8 (2) 51 127 39.4 300 12.9 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.2 N/A
350 12.9 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
400 12.9 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
450 12.9 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
500 12.9 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
cmin
70 100 150 200 250 300 350 400 450
100 X 12.3 12.3 12.3 12.3 12.3 12.3 12.3 12.3
150 13.7 14.7 14.7 14.7 14.7 14.7 14.7 14.7 14.7
200 13.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
250 13.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
1/2 (2) 51 152 64.6 300 13.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8 N/A N/A
350 13.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
400 13.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
450 13.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
500 13.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8 14.8
cmin
60 100 150 200 250 300 350 400 450
100 X 18.3 21.6 21.6 21.6 21.6 21.6 21.6 21.6
150 15.4 20.9 24.7 24.7 24.7 24.7 24.7 24.7 24.7
200 17.4 23.5 27.7 27.7 27.7 27.7 27.7 27.7 27.7
250 19.3 26.1 30.8 30.8 30.8 30.8 30.8 30.8 30.8
1/2 (3-1/4) 83 203 64.6 300 19.3 26.1 30.8 30.8 30.8 30.8 30.8 30.8 30.8 30.6 N/A
350 19.3 26.1 30.8 30.8 30.8 30.8 30.8 30.8 30.8
400 19.3 26.1 30.8 30.8 30.8 30.8 30.8 30.8 30.8
450 19.3 26.1 30.8 30.8 30.8 30.8 30.8 30.8 30.8
500 19.3 26.1 30.8 30.8 30.8 30.8 30.8 30.8 30.8
cmin
92 100 150 200 250 300 350 400 450
100 X X 20.3 20.3 20.3 20.3 20.3 20.3 20.3
150 X 20.5 23.3 23.3 23.3 23.3 23.3 23.3 23.3
200 21.8 23.2 26.3 26.3 26.3 26.3 26.3 26.3 26.3
250 23.7 25.1 28.6 28.6 28.6 28.6 28.6 28.6 28.6
5/8 (3-1/8) 79 127 104.0 300 23.7 25.1 28.6 28.6 28.6 28.6 28.6 28.6 28.6 N/A N/A
350 23.7 25.1 28.6 28.6 28.6 28.6 28.6 28.6 28.6
400 23.7 25.1 28.6 28.6 28.6 28.6 28.6 28.6 28.6
450 23.7 25.1 28.6 28.6 28.6 28.6 28.6 28.6 28.6
500 23.7 25.1 28.6 28.6 28.6 28.6 28.6 28.6 28.6
cmin
83 100 150 200 250 300 350 400 450
100 X 20.6 27.4 27.8 27.8 27.8 27.8 27.8 27.8
150 20.8 23.1 30.7 31.2 31.2 31.2 31.2 31.2 31.2
200 23.1 25.7 34.1 34.7 34.7 34.7 34.7 34.7 34.7
250 25.3 28.2 37.5 38.1 38.1 38.1 38.1 38.1 38.1
5/8 (4) 102 203 104.0 300 27.6 30.8 40.9 41.5 41.5 41.5 41.5 41.5 41.5 N/A N/A
350 27.9 31.1 41.3 41.9 41.9 41.9 41.9 41.9 41.9
400 27.9 31.1 41.3 41.9 41.9 41.9 41.9 41.9 41.9
450 27.9 31.1 41.3 41.9 41.9 41.9 41.9 41.9 41.9
500 27.9 31.1 41.3 41.9 41.9 41.9 41.9 41.9 41.9
cmin
121 100 150 200 250 300 350 400 450
100 X X X X X X X X X
150 X X X X 28.8 28.8 28.8 28.8 28.8
200 X X X 32.1 32.1 32.1 32.1 32.1 32.1
250 X X 35.4 35.4 35.4 35.4 35.4 35.4 35.4
3/4 (3-3/4) 95 203 151.9 300 33.3 X 37.7 37.7 37.7 37.7 37.7 37.7 37.7 N/A N/A
350 33.3 X 37.7 37.7 37.7 37.7 37.7 37.7 37.7
400 33.3 X 37.7 37.7 37.7 37.7 37.7 37.7 37.7
450 33.3 X 37.7 37.7 37.7 37.7 37.7 37.7 37.7
500 33.3 X 37.7 37.7 37.7 37.7 37.7 37.7 37.7
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 59
Mechanical Anchoring Systems
Nsr - Tension
Spacing, Npr - Pullout of Nsbgr - Sideface Blowout
Size hef hmin Strength of Anchor Ncbgr - Tension Breakout of Group1,3,4 (kN)
s Group1,5 of Group
Group2
mm mm kN mm c1 - edge distance (mm) kN kN
cmin
125 120 150 200 250 300 350 400 450
100 X X X X X X X X X
150 X X X 38.3 38.3 38.3 38.3 38.3 38.3
200 X X 36.4 42.0 42.0 42.0 42.0 42.0 42.0
250 31.5 X 39.6 45.7 45.7 45.7 45.7 45.7 45.7
3/4 (4-3/4) 121 203 151.9 300 34.1 X 42.8 49.5 49.5 49.5 49.5 49.5 49.5 N/A N/A
350 36.7 X 46.1 53.2 53.2 53.2 53.2 53.2 53.2
400 37.3 X 46.9 54.2 54.2 54.2 54.2 54.2 54.2
450 37.3 X 46.9 54.2 54.2 54.2 54.2 54.2 54.2
500 37.3 X 46.9 54.2 54.2 54.2 54.2 54.2 54.2
Notes:
A. For eccentric loading, multiply Ncbr by the modification factor for eccentrically loaded anchor groups, ec,N as per Section D.6.2.4.
B. If anchors are affected by more than one edge distance use formulas to calculate Concrete Resistance
f'c (MPa) fb
20 1.00
25 1.12
s
30 1.22
35 1.32
40 1.41
45 1.50
50 1.58 c1
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
60 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Nsr - Tension
Spacing, Npr - Pullout of Nsbgr - Sideface Blowout
Size hef hmin Strength of Anchor Ncbgr - Tension Breakout of Group1,3,4 (kN)
s Group1,5 of Group
Group2
mm mm kN mm c1 - edge distance (mm) kN kN
cmin
64 100 150 200 250 300 350 400 450
100 X 20.3 20.3 20.3 20.3 20.3 20.3 20.3 20.3
150 26.5 29.1 29.1 29.1 29.1 29.1 29.1 29.1 29.1
200 27.0 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
250 27.0 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
3/8 (2) 51 127 78.8 300 27.0 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6 28.4 N/A
350 27.0 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
400 27.0 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
450 27.0 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
500 27.0 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
cmin
70 100 150 200 250 300 350 400 450
100 X 20.3 20.3 20.3 20.3 20.3 20.3 20.3 20.3
150 27.7 29.1 29.1 29.1 29.1 29.1 29.1 29.1 29.1
200 28.3 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
250 28.3 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
1/2 (2) 51 152 129.2 300 28.3 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6 N/A N/A
350 28.3 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
400 28.3 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
450 28.3 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
500 28.3 29.6 29.6 29.6 29.6 29.6 29.6 29.6 29.6
cmin
60 100 150 200 250 300 350 400 450
100 X 26.4 30.2 30.2 30.2 30.2 30.2 30.2 30.2
150 28.0 34.9 39.5 39.5 39.5 39.5 39.5 39.5 39.5
200 36.2 44.5 50.0 50.0 50.0 50.0 50.0 50.0 50.0
250 45.2 55.1 61.5 61.5 61.5 61.5 61.5 61.5 61.5
1/2 (3-1/4) 83 203 129.2 300 45.2 55.1 61.5 61.5 61.5 61.5 61.5 61.5 61.5 61.2 N/A
350 45.2 55.1 61.5 61.5 61.5 61.5 61.5 61.5 61.5
400 45.2 55.1 61.5 61.5 61.5 61.5 61.5 61.5 61.5
450 45.2 55.1 61.5 61.5 61.5 61.5 61.5 61.5 61.5
500 45.2 55.1 61.5 61.5 61.5 61.5 61.5 61.5 61.5
cmin
92 100 150 200 250 300 350 400 450
100 X X 28.9 28.9 28.9 28.9 28.9 28.9 28.9
150 X 34.6 38.1 38.1 38.1 38.1 38.1 38.1 38.1
200 42.6 44.3 48.6 48.6 48.6 48.6 48.6 48.6 48.6
250 50.3 52.3 57.2 57.2 57.2 57.2 57.2 57.2 57.2
5/8 (3-1/8) 79 127 208.0 300 50.3 52.3 57.2 57.2 57.2 57.2 57.2 57.2 57.2 N/A N/A
350 50.3 52.3 57.2 57.2 57.2 57.2 57.2 57.2 57.2
400 50.3 52.3 57.2 57.2 57.2 57.2 57.2 57.2 57.2
450 50.3 52.3 57.2 57.2 57.2 57.2 57.2 57.2 57.2
500 50.3 52.3 57.2 57.2 57.2 57.2 57.2 57.2 57.2
cmin
83 100 150 200 250 300 350 400 450
100 X 28.7 36.4 36.9 36.9 36.9 36.9 36.9 36.9
150 34.0 36.9 46.0 46.5 46.5 46.5 46.5 46.5 46.5
200 42.6 46.0 56.6 57.3 57.3 57.3 57.3 57.3 57.3
250 52.2 56.1 68.4 69.2 69.2 69.2 69.2 69.2 69.2
5/8 (4) 102 203 208.0 300 62.7 67.2 81.3 82.2 82.2 82.2 82.2 82.2 82.2 N/A N/A
350 64.1 68.6 82.9 83.8 83.8 83.8 83.8 83.8 83.8
400 64.1 68.6 82.9 83.8 83.8 83.8 83.8 83.8 83.8
450 64.1 68.6 82.9 83.8 83.8 83.8 83.8 83.8 83.8
500 64.1 68.6 82.9 83.8 83.8 83.8 83.8 83.8 83.8
cmin
121 100 150 200 250 300 350 400 450
100 X X X X X X X X X
150 X X X X 43.9 43.9 43.9 43.9 43.9
200 X X X 54.6 54.6 54.6 54.6 54.6 54.6
250 X X 66.4 66.4 66.4 66.4 66.4 66.4 66.4
3/4 (3-3/4) 95 203 303.8 300 69.2 X 75.4 75.4 75.4 75.4 75.4 75.4 75.4 N/A N/A
350 69.2 X 75.4 75.4 75.4 75.4 75.4 75.4 75.4
400 69.2 X 75.4 75.4 75.4 75.4 75.4 75.4 75.4
450 69.2 X 75.4 75.4 75.4 75.4 75.4 75.4 75.4
500 69.2 X 75.4 75.4 75.4 75.4 75.4 75.4 75.4
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 61
Mechanical Anchoring Systems
Nsr - Tension
Spacing, Npr - Pullout of Nsbgr - Sideface Blowout
Size hef hmin Strength of Anchor Ncbgr - Tension Breakout of Group1,3,4 (kN)
s Group1,5 of Group
Group2
mm mm kN mm c1 - edge distance (mm) kN kN
cmin
125 120 150 200 250 300 350 400 450
100 X X X X X X X X X
150 X X X 54.1 54.1 54.1 54.1 54.1 54.1
200 X X 58.3 65.1 65.1 65.1 65.1 65.1 65.1
250 59.0 X 69.5 77.2 77.2 77.2 77.2 77.2 77.2
3/4 (4-3/4) 121 203 303.8 300 69.8 X 81.6 90.3 90.3 90.3 90.3 90.3 90.3 N/A N/A
350 81.5 X 94.7 104.5 104.5 104.5 104.5 104.5 104.5
400 84.7 X 98.2 108.3 108.3 108.3 108.3 108.3 108.3
450 84.7 X 98.2 108.3 108.3 108.3 108.3 108.3 108.3
500 84.7 X 98.2 108.3 108.3 108.3 108.3 108.3 108.3
Notes:
A. For eccentric loading, multiply Ncbr by the modification factor for eccentrically loaded anchor groups, ec,N as per Section D.6.2.4.
B. If anchors are affected by more than one edge distance use formulas to calculate Concrete Resistance
f'c (MPa) fb
20 1.00
25 1.12
30 1.22 s
35 1.32
40 1.41
45 1.50
50 1.58
55 1.66 c1 s
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
62 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Nsr - Tension
Spacing, Npr - Pullout of Nsbgr - Sideface Blowout
Size hef hmin Strength of Anchor Ncbgr - Tension Breakout of Group1,3,4 (kN)
s Group1,5 of Group
Group2
mm mm kN mm c1 - edge distance (mm) kN kN
cmin
64 100 150 200 250 300 350 400 450
100 X 28.3 28.3 28.3 28.3 28.3 28.3 28.3 28.3
150 39.6 43.5 43.5 43.5 43.5 43.5 43.5 43.5 43.5
200 40.6 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
250 40.6 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
3/8 (2) 51 127 118.2 300 40.6 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5 42.6 N/A
350 40.6 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
400 40.6 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
450 40.6 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
500 40.6 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
cmin
70 100 150 200 250 300 350 400 450
100 X 28.3 28.3 28.3 28.3 28.3 28.3 28.3 28.3
150 41.4 43.5 43.5 43.5 43.5 43.5 43.5 43.5 43.5
200 42.4 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
250 42.4 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
1/2 (2) 51 152 193.9 300 42.4 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5 N/A N/A
350 42.4 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
400 42.4 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
450 42.4 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
500 42.4 44.5 44.5 44.5 44.5 44.5 44.5 44.5 44.5
cmin
60 100 150 200 250 300 350 400 450
100 X 34.0 38.9 38.9 38.9 38.9 38.9 38.9 38.9
150 38.5 48.0 54.4 54.4 54.4 54.4 54.4 54.4 54.4
200 52.3 64.3 72.3 72.3 72.3 72.3 72.3 72.3 72.3
250 67.9 82.6 92.3 92.3 92.3 92.3 92.3 92.3 92.3
1/2 (3-1/4) 83 203 193.9 300 67.9 82.6 92.3 92.3 92.3 92.3 92.3 92.3 92.3 91.8 N/A
350 67.9 82.6 92.3 92.3 92.3 92.3 92.3 92.3 92.3
400 67.9 82.6 92.3 92.3 92.3 92.3 92.3 92.3 92.3
450 67.9 82.6 92.3 92.3 92.3 92.3 92.3 92.3 92.3
500 67.9 82.6 92.3 92.3 92.3 92.3 92.3 92.3 92.3
cmin
92 100 150 200 250 300 350 400 450
100 X X 37.5 37.5 37.5 37.5 37.5 37.5 37.5
150 X 48.0 52.9 52.9 52.9 52.9 52.9 52.9 52.9
200 62.1 64.6 70.8 70.8 70.8 70.8 70.8 70.8 70.8
250 75.5 78.5 85.7 85.7 85.7 85.7 85.7 85.7 85.7
5/8 (3-1/8) 79 127 312.0 300 75.5 78.5 85.7 85.7 85.7 85.7 85.7 85.7 85.7 N/A N/A
350 75.5 78.5 85.7 85.7 85.7 85.7 85.7 85.7 85.7
400 75.5 78.5 85.7 85.7 85.7 85.7 85.7 85.7 85.7
450 75.5 78.5 85.7 85.7 85.7 85.7 85.7 85.7 85.7
500 75.5 78.5 85.7 85.7 85.7 85.7 85.7 85.7 85.7
cmin
83 100 150 200 250 300 350 400 450
100 X 35.8 45.4 46.0 46.0 46.0 46.0 46.0 46.0
150 45.2 49.0 61.1 61.9 61.9 61.9 61.9 61.9 61.9
200 59.5 64.2 79.0 80.0 80.0 80.0 80.0 80.0 80.0
250 75.7 81.3 99.2 100.3 100.3 100.3 100.3 100.3 100.3
5/8 (4) 102 203 312.0 300 93.8 100.5 121.6 122.9 122.9 122.9 122.9 122.9 122.9 N/A N/A
350 96.1 102.9 124.4 125.8 125.8 125.8 125.8 125.8 125.8
400 96.1 102.9 124.4 125.8 125.8 125.8 125.8 125.8 125.8
450 96.1 102.9 124.4 125.8 125.8 125.8 125.8 125.8 125.8
500 96.1 102.9 124.4 125.8 125.8 125.8 125.8 125.8 125.8
cmin
121 100 150 200 250 300 350 400 450
100 X X X X X X X X X
150 X X X X 59.0 59.0 59.0 59.0 59.0
200 X X X 77.1 77.1 77.1 77.1 77.1 77.1
250 X X 97.4 97.4 97.4 97.4 97.4 97.4 97.4
3/4 (3-3/4) 95 203 455.7 300 103.9 X 113.0 113.0 113.0 113.0 113.0 113.0 113.0 N/A N/A
350 103.9 X 113.0 113.0 113.0 113.0 113.0 113.0 113.0
400 103.9 X 113.0 113.0 113.0 113.0 113.0 113.0 113.0
450 103.9 X 113.0 113.0 113.0 113.0 113.0 113.0 113.0
500 103.9 X 113.0 113.0 113.0 113.0 113.0 113.0 113.0
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 63
Mechanical Anchoring Systems
Nsr - Tension
Spacing, Npr - Pullout of Nsbgr - Sideface Blowout
Size hef hmin Strength of Anchor Ncbgr - Tension Breakout of Group1,3,4 (kN)
s Group1,5 of Group
Group2
mm mm kN mm c1 - edge distance (mm) kN kN
cmin
125 120 150 200 250 300 350 400 450
100 X X X X X X X X X
150 X X X 69.9 69.9 69.9 69.9 69.9 69.9
200 X X 79.0 88.3 88.3 88.3 88.3 88.3 88.3
250 83.1 X 97.8 108.7 108.7 108.7 108.7 108.7 108.7
3/4 (4-3/4) 121 203 455.7 300 101.4 X 118.5 131.2 131.2 131.2 131.2 131.2 131.2 N/A N/A
350 121.5 X 141.1 155.8 155.8 155.8 155.8 155.8 155.8
400 127.0 X 147.4 162.5 162.5 162.5 162.5 162.5 162.5
450 127.0 X 147.4 162.5 162.5 162.5 162.5 162.5 162.5
500 127.0 X 147.4 162.5 162.5 162.5 162.5 162.5 162.5
Notes:
A. For eccentric loading, multiply Ncbr by the modification factor for eccentrically loaded anchor groups, ec,N as per Section D.6.2.4.
B. If anchors are affected by more than one edge distance use formulas to calculate Concrete Resistance
f'c (MPa) fb
20 1.00
25 1.12
30 1.22 s
35 1.32
40 1.41
45 1.50
50 1.58 s
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
c1 s
64 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Vsr - Shear
Concrete Vcpr - Pryout
Size hef Strength of Vcbr - Shear Breakout (kN)1,2,4,5,6,7
Thickness, h Resistance
Anchor3
c1 - edge distance (mm) kcp X Ncbr
mm kN mm cmin 100 150 200 250 300 350 400 450 kN
127 3.1 5.5 8.2 11.0 13.7 16.5 19.2 22.0 24.7
200 3.1 6.0 10.3 13.8 17.2 20.7 24.1 27.6 31.0
300 3.1 6.0 11.0 16.9 21.1 25.3 29.5 33.8 38.0
3/8 (2) 51 10.2 400 3.1 6.0 11.0 16.9 23.6 29.2 34.1 39.0 43.9 1.0 x Ncbr
500 3.1 6.0 11.0 16.9 23.6 31.0 38.1 43.6 49.0
600 3.1 6.0 11.0 16.9 23.6 31.0 39.1 47.8 53.7
675 3.1 6.0 11.0 16.9 23.6 31.0 39.1 47.8 57.0
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
152 4.0 6.9 10.4 13.9 17.4 20.8 24.3 27.8 31.3
200 4.0 6.9 12.0 15.9 19.9 23.9 27.9 31.9 35.9
203 4.0 6.9 12.0 16.1 20.1 24.1 28.1 32.1 36.1
300 4.0 6.9 12.7 19.5 24.4 29.3 34.2 39.0 43.9
1/2 (2) 51 18.2 1.0 x Ncbr
400 4.0 6.9 12.7 19.5 27.3 33.8 39.4 45.1 50.7
500 4.0 6.9 12.7 19.5 27.3 35.9 44.1 50.4 56.7
600 4.0 6.9 12.7 19.5 27.3 35.9 45.2 55.2 62.1
675 4.0 6.9 12.7 19.5 27.3 35.9 45.2 55.2 65.9
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
203 3.2 6.9 12.0 16.1 20.1 24.1 28.1 32.1 36.1
300 3.2 6.9 12.7 19.5 24.4 29.3 34.2 39.0 43.9
400 3.2 6.9 12.7 19.5 27.3 33.8 39.4 45.1 50.7
1/2 (3-1/4) 83 18.2 2.0 x Ncbr
500 3.2 6.9 12.7 19.5 27.3 35.9 44.1 50.4 56.7
600 3.2 6.9 12.7 19.5 27.3 35.9 45.2 55.2 62.1
675 3.2 6.9 12.7 19.5 27.3 35.9 45.2 55.2 65.9
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
127 6.5 7.1 10.7 14.2 17.8 21.3 24.9 28.4 32.0
203 6.8 7.7 13.5 18.0 22.5 27.0 31.4 35.9 40.4
300 6.8 7.7 14.2 21.8 27.3 32.8 38.2 43.7 49.1
5/8 (3-1/8) 79 29.9 400 6.8 7.7 14.2 21.8 30.5 37.8 44.1 50.4 56.7 2.0 x Ncbr
500 6.8 7.7 14.2 21.8 30.5 40.1 49.3 56.4 63.4
600 6.8 7.7 14.2 21.8 30.5 40.1 50.6 61.8 69.5
675 6.8 7.7 14.2 21.8 30.5 40.1 50.6 61.8 73.7
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
203 5.8 7.7 13.5 18.0 22.5 27.0 31.4 35.9 40.4
300 5.8 7.7 14.2 21.8 27.3 32.8 38.2 43.7 49.1
400 5.8 7.7 14.2 21.8 30.5 37.8 44.1 50.4 56.7 2.0 x Ncbr
5/8 (4) 102 29.9
500 5.8 7.7 14.2 21.8 30.5 40.1 49.3 56.4 63.4
600 5.8 7.7 14.2 21.8 30.5 40.1 50.6 61.8 69.5
675 5.8 7.7 14.2 21.8 30.5 40.1 50.6 61.8 73.7
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
203 11.3 X 14.8 19.7 24.6 29.5 34.5 39.4 44.3
300 11.3 X 15.5 23.9 29.9 35.9 41.9 47.9 53.9
400 11.3 X 15.5 23.9 33.5 41.5 48.4 55.3 62.2 2.0 x Ncbr
3/4 (3-3/4) 95 45.2
500 11.3 X 15.5 23.9 33.5 44.0 54.1 61.8 69.5
600 11.3 X 15.5 23.9 33.5 44.0 55.4 67.7 76.2
675 11.3 X 15.5 23.9 33.5 44.0 55.4 67.7 80.8
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 65
Mechanical Anchoring Systems
Vsr - Shear
Concrete 1,2,4,5,6,7 Vcpr - Pryout
Size hef Strength of Vcbr - Shear Breakout (kN)
Thickness, h Resistance
Anchor3
c1 - edge distance (mm) kcp X Ncbr
mm kN mm cmin 100 150 200 250 300 350 400 450 kN
203 9.1 X 14.8 19.7 24.6 29.5 34.5 39.4 44.3
300 9.1 X 15.5 23.9 29.9 35.9 41.9 47.9 53.9
400 9.1 X 15.5 23.9 33.5 41.5 48.4 55.3 62.2 2.0 x Ncbr
3/4 (4-3/4) 121 45.2
500 9.1 X 15.5 23.9 33.5 44.0 54.1 61.8 69.5
600 9.1 X 15.5 23.9 33.5 44.0 55.4 67.7 76.2
675 9.1 X 15.5 23.9 33.5 44.0 55.4 67.7 80.8
f 'c (MPa) fb
20 1.00
25 1.12 V
30 1.22
35 1.32
40 1.41
45 1.50
50 1.58 c1
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
66 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 67
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
68 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 69
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
70 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 71
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
72 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 73
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
74 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 75
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
76 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 77
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
78 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
c1 c1 s
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 79
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
80 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12 s s
30 1.22
35 1.32 V V
40 1.41 s s
45 1.50
50 1.58
55 1.66
c1 c1 s
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 81
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
c1 c1 s
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
82 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 83
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
c1 c1 s
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
84 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
c1 c1 s
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 85
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
c1 c1 s
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
86 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
c1 c1 s
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊxÇ°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 87
Mechanical Anchoring Systems
£ÊÀÊÌ
iÀÊVVÀiÌiÊÃÌÀi}Ì
Ã]ÊÕÌ«ÞÊNcbr and Npr by 1 Design strengths in table are for anchors near one edge
corresponding influence of concrete strength factor, fb. only. The values do not apply where the distance to an
edge, measured perpendicular to c1, is less than 1.5c1.
ÓÊÀÊ
>ÀLÊ-Ìii]ÊÕÃiÊ /<ÊÌ>Lið
Shear force is assumed to act perpendicular, towards the
3 Design strengths in the table are based on resistance edge with no eccentricity.
`vV>ÌÊv>VÌÀÊ,]ÊvÊ-iVÌÊ°x°{°Ê>VÌÀi`ÊÌiÃiÊ
ÓÊÀÊÌ
iÀÊVVÀiÌiÊÃÌÀi}Ì
Ã]ÊÕÌ«ÞÊVcbr by corresponding
load Nf must be computed from the load combinations
influence of concrete strength factor, fb.
referenced in Clause 8.3.2. Design strengths for concrete
LÀi>ÕÌ]ÊNbr, pullout, Npr, and sideface blowout, Nsbr ÎÊÀÊ
>ÀLÊ-Ìii]ÊÕÃiÊ /<ÊÌ>Lið
are based on Condition B. Where supplementary
4 Design strengths in the table are based on resistance
reinforcement is provided to satisfy Condition A, design
`vV>ÌÊv>VÌÀÊ,]ÊvÊ-iVÌÊ°x°{°Ê>VÌÀi`ÊÃ
i>ÀÊ
strengths for Nbr and Nsbr may be increased by the ratio
load Vf must be computed from the load combinations
vÊ, condition A ÊÉÊ, condition B . This increase does not apply to
referenced in Clause 8.3.2. Design strengths for
pullout strength, Npr.
VVÀiÌiÊLÀi>ÕÌ]ÊVbr, are based on Condition B. Where
{Ê7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ supplementary reinforcement is provided to satisfy
service load levels (ft < fr) in the region of the anchor, the Condition A, this design may be increased by the ratio
`iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌÊÊÌiÃ]ÊNbr, may vÊ, condition AÊÉÊ, condition B . This increase does not apply to
be increased by #c,N. See Section D.6.2.6. pryout capacities, for which condition B is always assumed.
xÊ7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ xÊ7
iÀiÊ>>ÞÃÃÊ`V>ÌiÃÊÌ
>ÌÊÌ
iÀiÊÜÊLiÊÊVÀ>V}Ê>ÌÊ
service load levels (ft < fr) in the region of the anchor, the service load levels (ft < fr) in the region of the anchor, the
design strengths for concrete pullout in tension, Npr, may be `iÃ}ÊÃÌÀi}Ì
ÃÊvÀÊVVÀiÌiÊLÀi>ÕÌÊÊÃ
i>À]ÊVbr, may be
increased by 40%. See Section D.6.3.6. increased by 40%. See Section D.7.2.7.
88 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Minimum
Min. Nsr - Tension
Embedment Edge 1,3,4 Npr - Nsbr - Sideface
Size Concrete Strength of Ncbr - Tension Breakout (kN)
Depth, hef Distance Pullout1,5 Blowout
Thickness, h
cmin Anchor2
3/8 (2) 51 127 64 18.1 6.5 7.4 7.4 7.4 7.4 7.4 7.4 7.4 7.4 7.3 N/A
1/2 (2) 51 152 73 35.1 10.2 10.6 10.6 10.6 10.6 10.6 10.6 10.6 10.6 9.9 N/A
1/2 (3-1/4) 83 203 54 35.1 9.2 13.1 15.4 15.4 15.4 15.4 15.4 15.4 15.4 N/A N/A
5/8 (3-1/8) 79 127 83 56.4 11.1 12.6 14.3 14.3 14.3 14.3 14.3 14.3 14.3 N/A N/A
5/8 (4) 102 152 60 56.4 11.9 15.5 20.6 21.0 21.0 21.0 21.0 21.0 21.0 18.1 N/A
3/4 (3-3/4) 95 152 108 72.7 21.9 X 26.9 26.9 26.9 26.9 26.9 26.9 26.9 25.2 N/A
3/4 (4-3/4) 121 203 102 72.7 18.4 X 23.4 27.1 27.1 27.1 27.1 27.1 27.1 N/A N/A
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22
35 1.32
40 1.41
45 1.50
50 1.58 c1
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 89
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
90 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 91
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
c1 s
92 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Vsr - Shear
Concrete Vcpr - Pryout
Size hef Strength of Vcbr - Shear Breakout (kN) 1,2,4,5,6,7
Thickness, h Resistance
Anchor3
c1 - edge distance (mm) kcp X Ncbr
mm kN mm cmin 100 150 200 250 300 350 400 450 kN
127 3.1 5.5 8.2 11.0 13.7 16.5 19.2 22.0 24.7
203 3.1 6.0 10.4 13.9 17.4 20.8 24.3 27.8 31.2
300 3.1 6.0 11.0 16.9 21.1 25.3 29.5 33.8 38.0
3/8 (2) 51 13.8 400 3.1 6.0 11.0 16.9 23.6 29.2 34.1 39.0 43.9 1.0 x Ncbr
500 3.1 6.0 11.0 16.9 23.6 31.0 38.1 43.6 49.0
600 3.1 6.0 11.0 16.9 23.6 31.0 39.1 47.8 53.7
675 3.1 6.0 11.0 16.9 23.6 31.0 39.1 47.8 57.0
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
152 4.3 6.9 10.4 13.9 17.4 20.8 24.3 27.8 31.3
203 4.3 6.9 12.0 16.1 20.1 24.1 28.1 32.1 36.1
300 4.3 6.9 12.7 19.5 24.4 29.3 34.2 39.0 43.9
1/2 (2) 51 19.5 400 4.3 6.9 12.7 19.5 27.3 33.8 39.4 45.1 50.7 1.0 x Ncbr
500 4.3 6.9 12.7 19.5 27.3 35.9 44.1 50.4 56.7
600 4.3 6.9 12.7 19.5 27.3 35.9 45.2 55.2 62.1
675 4.3 6.9 12.7 19.5 27.3 35.9 45.2 55.2 65.9
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
203 2.7 6.9 12.0 16.1 20.1 24.1 28.1 32.1 36.1
300 2.7 6.9 12.7 19.5 24.4 29.3 34.2 39.0 43.9
400 2.7 6.9 12.7 19.5 27.3 33.8 39.4 45.1 50.7 2.0 x Ncbr
1/2 (3-1/4) 83 19.5
500 2.7 6.9 12.7 19.5 27.3 35.9 44.1 50.4 56.7
600 2.7 6.9 12.7 19.5 27.3 35.9 45.2 55.2 62.1
675 2.7 6.9 12.7 19.5 27.3 35.9 45.2 55.2 65.9
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
127 5.8 7.1 10.7 14.2 17.8 21.3 24.9 28.4 32.0
203 5.8 7.7 13.5 18.0 22.5 27.0 31.4 35.9 40.4
300 5.8 7.7 14.2 21.8 27.3 32.8 38.2 43.7 49.1
5/8 (3-1/8) 79 33.6 400 5.8 7.7 14.2 21.8 30.5 37.8 44.1 50.4 56.7 2.0 x Ncbr
500 5.8 7.7 14.2 21.8 30.5 40.1 49.3 56.4 63.4
600 5.8 7.7 14.2 21.8 30.5 40.1 50.6 61.8 69.5
675 5.8 7.7 14.2 21.8 30.5 40.1 50.6 61.8 73.7
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
152 3.6 7.7 11.7 15.5 19.4 23.3 27.2 31.1 35.0
203 3.6 7.7 13.5 18.0 22.5 27.0 31.4 35.9 40.4
300 3.6 7.7 14.2 21.8 27.3 32.8 38.2 43.7 49.1
5/8 (4) 102 33.6 400 3.6 7.7 14.2 21.8 30.5 37.8 44.1 50.4 56.7 2.0 x Ncbr
500 3.6 7.7 14.2 21.8 30.5 40.1 49.3 56.4 63.4
600 3.6 7.7 14.2 21.8 30.5 40.1 50.6 61.8 69.5
675 3.6 7.7 14.2 21.8 30.5 40.1 50.6 61.8 73.7
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
152 9.2 X 12.8 17.0 21.3 25.6 29.8 34.1 38.3
203 9.5 X 14.8 19.7 24.6 29.5 34.5 39.4 44.3
300 9.5 X 15.5 23.9 29.9 35.9 41.9 47.9 53.9
3/4 (3-3/4) 95 41.4 400 9.5 X 15.5 23.9 33.5 41.5 48.4 55.3 62.2 2.0 x Ncbr
500 9.5 X 15.5 23.9 33.5 44.0 54.1 61.8 69.5
600 9.5 X 15.5 23.9 33.5 44.0 55.4 67.7 76.2
675 9.5 X 15.5 23.9 33.5 44.0 55.4 67.7 80.8
c1 - edge distance (mm)
cmin 100 150 200 250 300 350 400 450
127 7.9 X 11.7 15.6 19.5 23.4 27.3 31.2 35.0
203 8.7 X 14.8 19.7 24.6 29.5 34.5 39.4 44.3
300 8.7 X 15.5 23.9 29.9 35.9 41.9 47.9 53.9
3/4 (4-3/4) 121 41.4 400 8.7 X 15.5 23.9 33.5 41.5 48.4 55.3 62.2 2.0 x Ncbr
500 8.7 X 15.5 23.9 33.5 44.0 54.1 61.8 69.5
600 8.7 X 15.5 23.9 33.5 44.0 55.4 67.7 76.2
675 8.7 X 15.5 23.9 33.5 44.0 55.4 67.7 80.8
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 93
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
94 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 95
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
96 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 97
Mechanical Anchoring Systems
Table 8 - Factored resistance for 2 or 4 KB-RTZ anchors subj ect to Shear Loads in Cracked Concrete (f ' c = 20 MPa)
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
98 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 99
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
100 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 101
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
102 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 103
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12
30 1.22 s V s V
35 1.32
40 1.41
45 1.50
50 1.58 c1 s
55 1.66 c1
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
104 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 105
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
c1 c1 s
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
106 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 107
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00
25 1.12 s s
30 1.22
35 1.32 V V
40 1.41 s s
45 1.50
50 1.58
55 1.66
c1 c1 s
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
108 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
55 1.66 c1 c1 s
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 109
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
110 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
c1 c1 s
55 1.66
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 111
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
112 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 113
Mechanical Anchoring Systems
f 'c (MPa) fb
20 1.00 s s
25 1.12
30 1.22 V V
35 1.32 s s
40 1.41
45 1.50
50 1.58
55 1.66 c1 c1 s
IÊÀÊvÌÌiÃ]ÊÀiviÀÊÌÊ«>}iÊnn°
114 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 115
Mechanical Anchoring Systems
Item No. Description Length (in.) Thread Length (in.) Box Quantity
Îä{xn£Ê /<ÊÎÉnÝÎÊ ÎÊ ÇÉnÊ xä
Îä{xnÓÊ /<ÊÎÉnÝÎÎÉ{Ê ÎÎÉ{Ê £xÉnÊ xä
Îä{xnÎÊ /<ÊÎÉnÝxÊ xÊ ÓÇÉnÊ xä
Îä{xn{Ê /<Ê£ÉÓÝÎÎÉ{Ê ÎÎÉ{Ê £xÉnÊ Óx
Îä{xnxÊ /<Ê£ÉÓÝ{£ÉÓÊ {£ÉÓÊ ÓÎÉnÊ Óx
Îä{xnÈÊ /<Ê£ÉÓÝx£ÉÓÊ x£ÉÓÊ ÎÎÉnÊ Óx
Îä{xnÇÊ /<Ê£ÉÓÝÇÊ ÇÊ {ÇÉnÊ Óx
Îä{xnnÊ /<ÊxÉnÝ{ÎÉ{Ê {ÎÉ{Ê ££ÉÓÊ £x
Îä{xnÊ /<ÊxÉnÝÈÊ ÈÊ ÓÎÉ{Ê £x
Îä{xäÊ /<ÊxÉnÝn£ÉÓÊ n£ÉÓÊ x£É{Ê £x
Îä{x£Ê /<ÊxÉnÝ£äÊ £äÊ ÈÎÉ{Ê £x
ÓäÓnnäÊ /<ÊÎÉ{Ýx£ÉÓÊ xÊ£ÉÓÊ ££ÉÓÊ £ä
ÓäÓnn£Ê /<ÊÎÉ{ÝnÊ nÊ {Ê £ä
ÓäÓnnÓÊ /<ÊÎÉ{Ý£äÊ £äÊ ÈÊ £ä
116 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement
Mechanical Anchoring Systems
Notes
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement 117
Hilti. Outperform. Outlast.
Hilti (Canada) Corporation 1-800-363-4458 www.ca.hilti.com s -EADOWPINE "LVD -ISSISSAUGA /. ,. 3
Hilti, Inc. (US) 1-800-879-8000 www.us.hilti.com s 0/ "OX 4ULSA /+ s 3ERVICIO AL #LIENTE EN ESPA×OL
(ILTI IS AN EQUAL OPPORTUNITY EMPLOYER s (ILTI IS A REGISTERED TRADEMARK OF (ILTI #ORP ¥#OPYRIGHT BY (ILTI )NC s ""
The data contained in this literature was current as of the date of publication. Updates and changes may be made based on later testing. If verification is needed that the data is still current, please contact the Hilti Technical
Support Specialists at 1-800-879-8000. All published load values contained in this literature represent the results of testing by Hilti or test organizations. Local base materials were used. Because of
variations in materials, on-site testing is necessary to determine performance at any specific site. Laser beams represented by red lines in this publication. Printed in the United States *ISO 14001 US Only
118 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com | Hilti (Canada) Corp. 1-800-363-4458 | www.hilti.ca | 2013 Limit States Supplement