Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Experience In Motion
Rotating equipment upgrade specialists
Induced and forced-draft, air-cooled heat exchangers require XLC bearing upgrade benefits
radial bearing support below the fan blade hub. This bearing
Increased reliability based upon a robust design with a
environment is characterized by high temperatures and poor
self-aligning bearing. Accommodates shaft thermal expansion
accessibility, leading to safety concerns for maintenance
by allowing freedom of movement in the axial direction. No
personnel. These challenges are often the root causes of
moving parts reduces potential failure modes.
the premature failure of traditional rolling-element bearings.
Furthermore, replacement of these bearings requires complete XLC composite bearing material is extremely durable,
disassembly of the fan and the use of heavy lifting equipment, eliminating lubrication requirements and reducing
greatly increasing equipment downtime and maintenance costs. maintenance costs.
Flowserve developed the XLC extended-life, composite journal Split design enables rapid change-out, reducing exposure
bearing to address the industry’s needs for improved safety time to hazards such as working at height, in elevated
and reliability while reducing maintenance costs. The XLC temperatures and around heavy lifting equipment.
bearing’s composite surface has self-lubricating properties,
In-situ replacement minimizes process disruption.
enabling it to run without additional lubrication. Moreover, fully
split components facilitate maintenance without dismantling Compatible with condition monitoring equipment
or disturbing the equipment. The result is an increase in overall to enable planned maintenance and avoid unplanned
equipment reliability, shorter bearing change-out times and downtime. Standard ¼-28 mounting feature to accomodate
reduced risk to personnel. accelerometer.
2 Flowserve.com
The Flowserve XLC
upper radial bearing
solution increases
reliability of air-cooled
heat exchangers.
Self-aligning spherical joint gives flexibility to XLC composite material delivers long life in Maintenance-friendly, fully split design
handle parallel misalignment over twice the adverse conditions.
Split components enable installation around
allowable level for the equipment.
Self-lubricating and wear-resistant properties the shaft without disassembling the equipment.
Designed to last through multiple bearing of the carbon fiber-reinforced thermoplastic
Semi-cartridge clamshell reduces the number
change-outs, the bronze bearing carrier assembly enable XLC bearings to operate without grease
of installed components to four.
has features to provide anti-rotation and protect supply, unlike roller bearings.
against galling caused by vibration.
Available repair kits for each size provide all Prevent dropped or
components needed to quickly repair the XLC misplaced bolts
bearing in the field.
XLC Series 3
XLC standard
XLC dimensions,
standard
XLC mm
dimensions,
standard [in][in]
mm
dimensions, mm [in]
203.2 [8.00]
203.2 [8.00] 83.883.8
[3.30]
[3.30]
203.2 [8.00]
203.2 MINMIN
[8.00] 22.222.2
[.88][.88]
4X 4X
20.620.6
[.81][.81] 215.9[ 8.50] MAX
215.9[ 8.50] MAX
23.523.5
[.92][.92]
NOMINAL
NOMINAL
SHAFT
SHAFT
203.2 [8.00]
203.2 SIZE25.725.7
[8.00] SIZE [1.01]
[1.01]
1/4-28 UNF-2B
1/4-28 UNF-2B
VIBRATION PORT
VIBRATION PORT
UNLESS SPECIFIED
UNLESS OTHERWISE:
SPECIFIED OTHERWISE: ♦ MARK ♦ MARKPER MFG
PERSTD
MFG1-R-5
STD 1-R-5 REV: REV:DATE:DATE: BY: BY: CHKD:
CHKD: APPR:APPR: ECN: ECN: BALLOON NO: NO:
BALLOON SIMILAR TO: TO:
SIMILAR PART:PART:
FEATURE CONTROLS
FEATURE PER ASME
CONTROLS Y14.5M-1994
PER ASME (..) DENOTE
Y14.5M-1994 REFERENCE
(..) DENOTE ONLY.ONLY.
REFERENCE REVISION NOTE:NOTE:
REVISION SCALE:
SCALE: DRAWN:
DRAWN:
APPLIES TO TURNED
APPLIES SURFACES
TO TURNED SURFACES BREAKBREAK/ DEBURR SHARPSHARP
/ DEBURR EDGES .016 .016
EDGES DATE:DATE: SHEET:
SHEET: OF: OF:
PARALLEL
COAXIAL
SURFACES
COAXIAL DIAMETERS .002
DIAMETERS
.002
PARALLEL SURFACES .002
.002
INTERNAL
ANGLES
Nominal Shaft Size, in
CORNERS R
± 2° ± SURFACE
ANGLES
.016 MAX.
INTERNAL CORNERS R .016 MAX.125
ROUGHNESS
2° SURFACE
THIS
125
EMBODY
ROUGHNESS MAY MAY
DRAWING
THIS AND
DRAWING ANY
AND
OR REPRESENT
EMBODY
NOT NOT
BE REPRODUCED,
DESIGN,
ANY
ARE ARE
OR REPRESENT
DEVELOPMENT,
DESIGN,
THE THE
NOR NOR
BE REPRODUCED,
DEVELOPMENT,
PROPERTY
ANY SUBJECT
Shaft Size, in
INVENTION
OF FLOWSERVE
PROPERTY
MATTER
ANY SUBJECT SHOWN
MATTER
OR
INVENTION COPYRIGHT
OR
CORPORATION.
OF FLOWSERVE
HEREIN
SHOWN MAY MAY
HEREIN
WHICH
COPYRIGHT IT
WHICH
THISTHIS
CORPORATION.
MAY
DRAWING
IT MAY
DRAWING
BE MANUFACTURED,
BE MANUFACTURED,
DIMENSIONS
DIMENSIONS
IN IN
Standard Assembly Number
INV INV
JAN 16
JAN 16
CHKD:CHKD:
APPR:APPR:
DRAWING NO: NO:
DRAWING REV: REV:
PERPENDICULAR SURFACES
PERPENDICULAR .0005/INCH
SURFACES .0005/INCHX.XX=X.XX=
± .01 ± .01X.XXX= ± .005± .005
X.XXX= WITHOUT WRITTEN
WITHOUT PERMISSION
WRITTEN FROM
PERMISSION AN AUTHORIZED
FROM AGENT
AN AUTHORIZED OF FLOWSERVE
AGENT CORPORATION.
OF FLOWSERVE CORPORATION. THIRDTHIRD
ANGLEANGLE F.O. NO:
F.O. NO:
flowserve.com