Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Column
Column height: d = 268 mm
Column width bf = 450 mm
Column Flange: tf = 25.4 mm
Column web: tw = 0 mm
Base plate
Yield strength of base plate: Fy = 345 MPa Slab or pedestal
Base plate thickness: tp = 31.75 mm Pier width: PB = 600 mm
Base plate width: N = 500 mm Pier height: PN = 600 mm
Base plate height: B = 500 mm thickness pier: PH = 1000 mm
Concrete strength f´c = 28 MPa
The design Loads
Design compresion the column: Pu = 149.47 tonnef
Design Tension the column: Tu = 75.18 tonnef
‾‾‾‾
A2
Base plate area: A1 = 2500 cm 2 ―― = 1.2
A1
Area projected on pedestal: A2 = 3600 cm 2
Dist. Efect. cantilever base plate in X: m = 123 mm
Dist. Efect. cantilever base plate in Y: n = 70 mm
Maximum design bearing stress Fp = 28.1 MPa
Concrete crush resistance ϕfp = 466.1 tonnef
3b.- bending of the plate in the compression interface at the base plate end
Loads:
An anchor bolt has a factored bolt tension Nua = 14.90 tonnef
An anchor bolt has a factored bolt shear Vua = 12.60 tonnef
5c.- Breakout
Ductility for breakout will be insured by lapping the bolt with the reinforcing bars.
The modification factors: ψt = 1.3 ψe = 1.0 ψs = 1.0
λ = 1.0 ψ = 1.4
5d.- Pullout
To insure ductility for pull-out and side-face blowout, the concrete strength must be greater than
Anchor bolt expected resistance Tesp = 50 tonnef
Bearing area Abgr = 4520 mm 2
Tesp
The Pullout strength ϕNpn = 100 tonnef ――― = 0.50
ϕNpn
Tesp
Side-face blowout strength ϕNsbg = 52 tonnef ――― = 0.95
ϕNsbg
Normally, side-face blowout would not need to be checked if ties are provided in the region at the
anchor bolt nut location such that the ties would cross the failure plane.
Loads:
Resistance to friction ϕVnμ = 14.0 tonnef ACI 22.9 / NSR 10 - C.11.6
Shear Design load Vv = 61.6 tonnef
6a.- Bearing strength of concrete check: (ACI 349 Ap. D, sec. D.4.6.2)
Vv
Bearing strength of concrete fc = 67 tonnef ―― = 0.91
fc
6b.- Shear strength toward free edge check: (ACI 349 Ap. D, sec. D.11.2)
Area of the failure plane Av = 2024 cm 2
Vv
Shear strength of the concrete reinforced ϕVnat = 73 tonnef ――― = 0.85
ϕVnat
6c.- Flexural design, thickness required for shear lug (AISC 360, Cap F. D, sec F.1.1)
Moment design on the shear lug Mlug = 6156 kgf ⋅ m
Plastic module cross-shaped plate shear lug Zlug = 616 cm 3
Plastic moment cross-shaped plate shear lug MP = 19.48 tonnef ⋅ m
treqs
Thickness required cross-shaped plate treqs = 9.34 mm ――= 0.37
tlug
kgf
Forces design longitudinal unit welding fr = 6048 ――
cm
kgf fr
Welding design resistance ϕRns = 7517 ―― ―― = 0.80
cm ϕRns
Creado con PTC Mathcad Express. Consulte www.mathcad.com para obtener más información.