Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SERVICE MANUAL
UT4000F Pro
PATIENT MONITOR
B/0
SERVICE MANUAL
TABLE OF CONTENT
Chapter 1 General Introduction: Introduces the users, applications, main contents, safety and
service information of the manual.
Chapter 3 Maintenance: Includes making maintenance plan, visual inspection, cleaning, check
and test.
Chapter 4 Troubleshooting: Introduces the monitor structure and system defaults setting.
B. Safety
1. Manufacturer Responsibility
The Company shall be responsible for the safety, reliability and performances of the monitor
under the following conditions:
2. Precautions
1-1
GOLDWAY INC. UT4000F Pro Service Manual
● The user of the monitor must be qualified persons who have been trained and are capable of
using the monitor correctly.
● To protect patients’ safety, use only parts and accessories manufactured or recommended by the
Company.
● Before connect the equipment to any other equipment not recommended in the manual, please
contact the Company in advance.
Note: As the parameter configuration of the monitors can be different, there may not be some
marks on the monitor you purchased.
Fuse.
CE0123 The product is in conformity with the requirements of MDD 93/42/EEC through
certification by TUV P.S.
~ Alternating Current.
4. Classification
In accordance with IEC 60601-1 standards, UT4000F Pro monitor and its applied parts are
classified as follows:
● Classified according to type of electric shock protection: Class I, with internal power supply.
● Classified according to degree of electric shock protection: BF type applied part – NIBP, SpO2,
1-2
GOLDWAY INC. UT4000F Pro Service Manual
5. Terminology
The terminology used in the manual “ Warning”, “Caution” and “Note” indicates the hazard and
remind users of the precautions to be taken according to the degree of importance. Hazard
indicates the potential cause which may result in injury to human body.
Warning: indicates the potential hazard or unsafe action which may result in death or serious
injury if not avoided.
Caution: indicates the potential hazard or unsafe action which may result in relatively minor injury
to human body or damage to product if not avoided.
Note: provides useful information and hint reminding user to pay attention to and ensure that the
monitor may play its role to the maximum degree.
C. Service Information
1. Service Requirements
2. Equipment Identification
Each monitor manufactured by the Company has a unique serial number for equipment
identification and service.
1-3
GOLDWAY INC. UT4000F Pro Service Manual
A. Product Description
The monitor is easy to carry, advanced function, easy to use.
B. Front Panel
The front panel of the UT 4000F Pro multi-parameter patient monitor is as follows:
2-1
GOLDWAY INC. UT4000F Pro Service Manual
(1) Power LED When the patient monitor is powered on, the LED is in green.
Indicator When the patient monitor is connected to AC power supply but
not turned on, the LED is in orange, indicating that the internal
battery is being charged.
(2) Screen TFT screen for displaying waveform, menu, alarm status and
vital sign measurement results.
(3) Alarm Light Red/Yellow two-color alarm light. The light’s shine status
Indicator change with the serious level of the alarm; light is red and wink
when the level is highest; light is yellow and wink when the
level is higher; light is yellow when the level is low.
(4) Main Menu When screen does not display menu bar, press this key to display
the main menu bar. When the screen is displaying main menu
bar, press this key, then the main menu bar will disappear from
the screen.
(5) Waveform When a waveform sweep is displayed, press the key to freeze the
Freeze/Restore waveform.
When a waveform is being frozen, press this key to unfreeze the
waveform and restore waveform sweep.
(6) Start/Stop Press this key to start a blood pressure measurement. If the
NIBP Measure patient monitor is in the process of blood pressure measurement,
press this key to stop blood pressure measurement.
(8) Print Press this key to activate the recorder to print. Press this key
again to stop printing.
(9) Setup Menu Press this key to enter System Setup menu. Press it again the
menu will disappear.
(10) Trim Knob When menu is displayed, rotate the knob to select the functions
at the bottom of the screen. When mouse cursor (arrow) is
pointing to a certain function, press the knob to select the
function. Then rotate the knob to select the desired item. In the
end, press the knob again to confirm the selection.
(11) Power Button Press this button to turn on /off the patient monitor.
C. Rear Panel
The rear panel of UT 4000F Pro is as shown in Figure 3-2.
2-2
GOLDWAY INC. UT4000F Pro Service Manual
1、 Fuse 1
2、 110-230VAC, 50/60Hz, external power supply socket
3、 Fuse 2
4、 Equipotentiality
5、 Heat Exhaust
6、 RS422 Communication port
7、 External display socket
8、 Handle
2-3
GOLDWAY INC. UT4000F Pro Service Manual
D Side Panels
There are seven sockets/receptacles on the left side panel,
respectively:
IBP1/2 There are two sockets on the right side panel of the IBP measurement
module, accepting the IBP cable.
There is an optional built-in recorder on the right side panel of the patient monitor
which is used to print the monitoring waveform and data.
Loading thermal paper: Open the door of the recorder by pressing in the
direction as indicated by the arrow, place print paper inside according to the diagram
on the recorder panel. Pull the paper until a few inches of paper is showing. Close the
side cover and now the recorder is ready to print.
NOTE: The recorder in UT4000F Pro is optional. If you have not ordered the
recorder, please disregard the descriptions that refer to the recorder.
E. Technical specification
1. Safety Standards & Quality System
Designed to meet EN 60601-1:1990 + A1:1993 + A2:1995
Class I equipment, internally powered equipment, double in sulated
Type BF and CF applied parts
ISO9001 & EN46001 Certified
2-4
GOLDWAY INC. UT4000F Pro Service Manual
2. Power Requirements
3. Performance Specifications
(1) ECG
(2) Respiration
2-5
GOLDWAY INC. UT4000F Pro Service Manual
2-6
GOLDWAY INC. UT4000F Pro Service Manual
Number of channels 2
Measure range 0 ~ 50C
Probe type YSI Series 400
Scale Celsius
Accuracy 0.1C
Resolution 0.1C
Refurbish time about 1 second
Size 12.1″
Matrix 800 (H) x 600 (V) pixels
5. Recorder (Optional)
6. Environmental Specifications
2-7
GOLDWAY INC. UT4000F Pro Service Manual
F Requirements
1、 Power requirement
At least one grounded duplex wall receptable should be provided for each monitor.
2、Ventilation requirement
The monitor will produce heat while working. So the monitor should be located in an
ventilated place.
Caution:Do not locate the monitor in an enclosed area that may restrict the heat
dissipated by it.
Caution:The monitor must be located no closer than 4 inches(10 cm) from any
partition or wall. The monitor should be approximately 12 inches (30 cm) from any
overhead partition or the ceiling.
2-8
GOLDWAY INC. UT4000F Pro Service Manual
A. Maintenance Plan
To maintain the normal running of the monitor, a good maintenance plan must be made. We
recommend the following:
1. Visual inspection: Before use, operator shall first inspect the outside appearance of the
equipment. Service personnel shall first inspect the outside appearance of the equipment before
maintenance.
2. Cleaning: Operator shall first clean the equipment before use. Maintenance personnel shall
clean the equipment after maintenance.
3. Thorough inspection: When monitor is received, a qualified person must inspect the monitor
thoroughly. Service personnel shall inspect the monitor thoroughly every time when maintenance
is done or every 12 months.
4. Leakage current test: Operator shall inspect the equipment before using the monitor. Service
personnel shall inspect the equipment before maintenance.
5. NIBP calibration: Each year qualified personnel shall perform NIBP calibration for the
monitor.
B. Manufacturer’s Responsibilities
If customer has not implemented the maintenance plan, which results in inaccurate measurement
of the monitor or potential hazard to operators and patients, unless otherwise agreed by both
parties, the manufacturer shall not undertake any responsibilities. All responsibilities shall be
taken by the monitor user.
C. Visual Inspection
Before using the monitor, make sure to inspect the monitor carefully:
1. Carefully inspect the outside of the monitor, display and control parts to see if there is any
apparent physical damage. If yes, please do not use the monitor. Please contact authorized service
personnel and reflect the damage until problems are settled before connect the monitor to patients.
2. Inspect all cables, connecting wires and external connectors. If there is any damage, please do
not use the monitor. Please contact authorized service personnel and reflect he damage until the
problems are settled before connect the monitor to patients.
3. Inspect if the safety marks on the equipment is distinct.
D. Cleaning
1. Clean the display screen
3-1
GOLDWAY INC. UT4000F Pro Service Manual
Use a soft cloth soaked in glass detergent to gently wipe the screen.
Caution: Do not spry glass detergent or other detergent directly to the screen.
Use a clean cloth soaked in mild soap water to clean the surface of the equipment.
3. Manufacturer Recommendation
Multi-functional simulator
ECG cable, 5-lead, AHA
NIBP extension tube
Temperature extension cable
Digital pressure meter
SpO2 simulator
SpO2 cable
(1) Connect power cable between the wall outlet and monitor power connector and power the
monitor up.
(2) Inspect if the power indicator lights up and the indicator color.
Green: The monitor is powered on and in normal working status.
Yellow: The monitor is connected to AC power but not turned on. It is under internal battery
charging status.
(3) Press the power switch of the monitor to turn on the monitor and unplug the power cable.
Inspect if the power indicator is green and if a battery mark is in the status box on the screen
showing that the monitor is powered by battery.
(4) Conduct ECG test according to the following instructions.
(5) Reconnect the monitor to AC power and start the tests.
3-2
GOLDWAY INC. UT4000F Pro Service Manual
3. ECG test
4. Respiration test
(1) Connect ECG cable to the ECG socket properly and set the simulator as follows: respiration
baseline resistance: 500 Ohm, Respiration Delta R: 0.5 Ohm, Respiration lead: I or II.
Respiration rate: 30bpm
(2) Set monitor respiration lead to be RA-LA or LL-RL and set respiration waveform channel.
(3) Observe if respiration parameter area displays reading 30±2bpm, waveform channel displays
respiration waveform.
(4) Change monitor respiration lead and observe the above parameter and waveform.
(5) Unplug ECG cable and respiration test is complete.
5. Temperature Test
Invasive blood pressure test is applicable to monitor which is configured with invasive blood
pressure function.
3-3
GOLDWAY INC. UT4000F Pro Service Manual
(2) Connect one end of the BP cable to the BP1 socket on the simulator, the other end to the IBP1
socket on the monitor.
(3) Press Zero in the IBP menu.
(4) Select ART to be the blood pressure measurement position. Observe if the IBP parameter area
displays blood pressure reading on the screen and if the waveform channel has IBP waveform
(IBP channel shall be set in the menu in advance).
(5) Change the BP output in the simulator to be 200mmHg.
(6) Observe if the parameter display area on the screen displays 200 or 200 ±6mmHg.
(7) Unplug the cable between the simulator and the monitor. IBP test is complete.
The accuracy of the NIBP reading of the monitor is decided by: NIBP calibration and the
measurement range of the blood pressure sensor. Correct testing and calibration methods are as
follows:
(1) Unplug all cables connected to the monitor except for the power cable.
(2) Turn on the power switch of the monitor.
(3) Connect the hose of the cuff to digital pressure meter, auto inflating bladder and NIBP socket
at the side panel of the monitor through a 3-way TEE. Inflate the cuff to a certain pressure
level, compare the pressure reading on the digital pressure meter and the monitor screen to see
if their value difference are less than 3 mmHg. If not, you need to do blood pressure
calibration.
(4) Input a password and enter the system maintain menu as follows,
(5) Rotate knob to Pressure Compensation, select the value to be calibrated (-6 – 6mmHg or
Auto), then exit the system calibration menu.
(6) Repeat (3) , if digital pressure meter and monitor screen have the same pressure value, then
calibration is complete. If not, re-calibration is required. If the same results cannot be obtained
3-4
GOLDWAY INC. UT4000F Pro Service Manual
9. Speaker Test
(1) Turn on alarm sound and set Heart Rate alarm limits. Test if the monitor will make alarm
sound when heart rate is outside alarm limits.
(2) Silence alarm sound and test if the monitor will make alarm sound when heart rate is outside
the alarm limits.
(3) Turn on the alarm sound. Speaker test is complete.
After monitor is networked with the central station monitoring system, inspect if the ECG
waveform and its parameters will be correctly displayed on the central station monitoring system.
When the above tests are complete, turn off all the test devices and monitor and remove the test
devices away from the monitor.
In order to establish a systematic maintenance plan, we recommend all safety tests and records
shall be made under the following circumstances: Upon reception of the monitor, every other year,
and the monitor is opened for repair.
Caution: If hospital staff did not observe the maintenance plan, which leads to inaccurate
measurement of the monitor or potential hazards to operators or patients, unless otherwise agreed
by both parties, manufacturer shall not undertake any responsibilities. All responsibilities shall be
undertaken by the user of the monitor.
3-5
GOLDWAY INC. UT4000F Pro Service Manual
Section 4 Troubleshooting
A. Special Components
Surface mounted devices are used to aid in miniaturizing the electrical assemblies
within the monitor.
B. Power Failure
Phenomenon: When the monitor is powered up, there is no display on the screen
and LED does not light up.
Inspection method: 1) Without connecting the monitor to AC power supply, check the
battery power level.
2) When connecting the monitor to AC power supply, check the
connection between the power socket and the plug of the
monitor, the power cable, and the AC output.
Solution: Make sure all connections are reliable and connect the monitor to
AC power supply to charge the internal battery.
1 No ECG waveform
Inspection method: Check ECG electrodes contact with patient’s skin and check all
leadwire connections.
4-1
GOLDWAY INC. UT4000F Pro Service Manual
Solution: 1) Replace ECG electrodes and clean the skin surface where
electrodes are applied.
2) Resistance of 1kΩ should exist between extension wires
applied to patient body to the leads of the ECG connector. If it
is indefinitely large, it shows that the leadwire is broken and
should be replaced.
3) If ECG waveform channel shows “No signal received”, then it
shows there is some problem in the communication between
ECG module and the main system. If this message still remains
after the monitor is turned off and on again, please contact the
supplier.
Phenomenon: ECG baseline is not stable, occasionally shifts out of the display
area.
Inspection method: 1) Check if the working environment is very humid and if the
monitor has moisture inside.
2) Check if the electrode’s quality is good, and the skin surface
where the electrode is applied is clean.
Solution: 1) Turn on the monitor and let it run for 24 hours to remove
moisture inside.
2) Replace it with good electrode, clean the skin surface where the
electrode is applied.
Phenomenon: ECG waveform is too large, no entire frame of ECG waveform can
be seen.
Inspection method: Check if the ECG scale is so high that it results in the ECG
waveform overflow.
Inspection method: Check the grounding condition of the monitor and the
electrosurgical equipment.
Solution: Make sure the monitor and the electrosurgical equipment are
properly grounded.
4-2
GOLDWAY INC. UT4000F Pro Service Manual
Inspection method: Check if the ECG electrodes are located correctly and if the ECG
electrodes contact with patient’s skin is well.
Solution: 1)Apply the ECG electrodes as Fig. 4-2 in P4-5 show, clean the
skin surface where electrode is applied.
2)Select other lead.
6 No SpO2 reading
Inspection method: Check the finger probe to see if there is red light, if the arm is being
pressed, and if the room temperature is too low.
Solution: If there is no red light in the finger probe, check the extension cable
and connecting part. When room temperature is very low, do not
expose patient’s arm outside , which will affect the measurement
results. Do not measure blood pressure and SpO2 on the same arm.
Pressing the arm will affect SpO2 measurement.
Inspection method: 1) During prolonged monitoring and surgery, check if patient arm
movement results in interruption of SpO2 measurement.
2) Check the SpO2 extension cable.
Solution: Keep the patient steady. It is normal if SpO2 value is lost due to
hand movement. If SpO2 extension cable is faulty, replace it.
Inspection method: Check if the cuff leaks or the tube connector leaks.
4-3
GOLDWAY INC. UT4000F Pro Service Manual
4-4
GOLDWAY INC. UT4000F Pro Service Manual
Open
machine ………………………………………………………………….Error!
Bookmark not defined.
Separate the front and rear
endosures...………………………………………...Error! Bookmark not defined.
Remove metal frame……………………………………………………………4
Remove ECG module…………………………………………………………..5
Remove the function board …………………………………………………..6
Disassemble function board ………………………………………………….7
Re-assemble temperature socket………………………………………………..8
Function PCB assembling………………………………………………………9
Function Board installation…………………………………………………….10
Bracket installation……………………………………………………………. 11
Control board installation………………………………………………………12
Function board installation assembly…………………………………………..13
1/13
GOLDWAY INC. UT4000F Pro Service Manual
6-1
GOLDWAY INC. UT4000F PRO Service Manual
B/0 7-1
U210-P5:-20~20mV U216-P3:5.7~6.3V
KEYBOARD
GND GND
T1_1 T1_1
J301
NC NC T1_2 T1_2
POWER ON POWER ON T2_1 T2_1
+15V +15V T2_2 T2_2
+5V +5V
CODER
NC NC
GND GND
SPO2 SPO2 SET
KR0 KR0
NIBP
ENCD1 ENCD1
GND GND KR1 KR1 NC NC J2_1 J2_1
ENCD2 ENCD2 ENCD2 ENCD2 SGND SGND NC NC
ENCD1 ENCD1 KR2 KR2 SGND SGND NC NC
KR0 KR0 KL0 KL0 NC NC J2_4 J2_4
KL0 KL0 KL2 KL2 SGND SGND SGND SGND
+5V +5V KL1 KL1 +12V +12V NC NC J2_6 J2_6
J2
+12V +12V -5V -5V J2_7 J2_7
J2 J1 J102 J8 J1
JP1 GND
GND
GND
GND
SPO2R
NC
SPO2R
NC
NC
J2_9
NC
J2_9
+5V +5V +5V +5V SGND SGND
+5V +5 SGND SGND
IRXD IRXD SGND SGND
ITXD ITXD +5V +5V
LCD PC104 J1
SPO2R SPO2R SGND SGND
J403
SPO2R SPO2R
+5V
DC/DC
+5V
RXB2 RXB2
TXB2 TXB2
NET SET
+5V +5V
J401 J402
+5V +5V
ERXD ERXD TXD+ TXD+
ERXD ERXD TXD- TXD-
ETXD ETXD
J9
ETXD ETXD
+5V +5V RXD+ RXD+
J107
GND GND RXD- RXD-
GND GND
GND GND
FAN
+ SPK
J103
- GND
STXD STXD
Name UT4000F pro Type
STXD STXD
SRXD SRXD
SRXD SRXD
BACKLIGHT
R133
470
Q106
R135
10K
PC104电源5V LCDSLEEP
U105 U108 VPW
J107 LM2576-5 VPW VCC LM2576-5
4 1 2N3904 4 1
2 FBK Vin R131 FBK Vin
D 2 5 2 5 D
1 Vout ON C110 Vout ON
L101 300 L102
TO PC 100uH D110 显示器电源 100uH D111
C111 1N5822 U106 1N5822
1000u/16V J108 LM2576-ADJ VPW C115 C114 C113
LCD POWER 4 1 1000u/16V 100u/25V
FBK Vin
2 5
4 Vout ON C130
L104
3 D114 D113 1000uF/25V
100uH
2
键盘口 1
6.5V C112 1N5822
1000u/16V R137 D115
J106 20K 1N4001
KEYDATA
1
KEYCLK Vcc
2
Vbak U104
3
HT7150
4
3 2
Vo Vi
Q108
KEYBOARD C108 C109
10u/16V 扬声器
1
C125 Vcc Q111
Q109 J103
2
Vdc
C D106 1 C
SPEAK Vbak
D102 Q103 R148
100R
1
U9024
VPW
R146 Q110 U107
12V 10K
VCC
IMP809
直流12V C104 Q104 C105
RESET
3 1RESET
Q101 D101 1000uF/25V U9024 106
GND
J105 1N4001 R114
ACON R101 R102 3.3K R115
2 300
1 .33/.5W .33/.5W
C106 J104 J101 串行下载
2
DC F101 BATT ISP
FUSE Q105
16
6
5
4
3
2
1
Vbak
2
LEDCONT
R105 R117 1 2
5 11 U101 ACON
+VIN TRICKLE 47K 100K KEYTXD 3 4 VCC
9 12 13 17 KEYDATA
OVCHG CHGEN PB1(OC1) SCK/PB5 5 6
3 13 12 16
C/S+ VSENSE ICP/PB0 MISO/PB4 7 8
10 23 15
SLC ADC0/PC0 MOSI/PB3 9 10
SOURCE
Vdc 24 29 1RESET
C/SOUT
TXD/PD1 ADC5/PC5
3 LCDSLEEP 14 27
SS/PB2 ADC4/PC4
1 VCC C122 LEDCONT 25 26
ADC2/PC2 ADC3/PC3
15
14
1
8
R121 2 U103A 9
R112 160K R109 Y101 T1/PD5
LM358 7 2
470 R143 XTAL1 T0/PD4
7.3728M 1
INT1/PD3
4
A A
1 2 3 4 5 6
P+5 VCC P-5
P+5ADC P+5L P-5ADC
L601 L603 L602
BLM21B222S BLM21B222S BLM21B222S
U601 P+5ADC
15 20
ADDOUT DOUT VDD
16
SSTRB C610 C611
17
ADDIN DIN 10u 16V
18
ADCS /CS
19
ADSCLK SCLK
13
AGND
R601 47K 10u 16V
1 C609
I CH0 C608
R602 47K 2 9
II CH1 VSS
R603 47K
3 P-5ADC
III CH2
R604 47K
4 C607
U CH3
10
R605 47K /SHDN
5
RESP CH4
R606 330
6
TEMP CH5
7
CH6
11
VREF
8
C601 C602 C603 C604 C605 C606 CH7
14 12
DGND REFADJ
C614
10u 16V
VCC
File No. Page of
C430
22u 16V
Design Audit Approve
RA194 VCCECG
CA135
R132
VREFECGR
C134 P-7ECG RA157
R148 CA132 RA154
RAB R130
4
11
R102A RA153
C102 2 CA134 U112B
4
RA195 2 1 6
1 RA152 3 7 2
LAB R131 3 AD U112A 5 1
U103A 3
U113A
8
R102 P+7ECG RA150
4
R133 R149 RA151 RA158 VCCECG
8
13 CA133
14 RAB C135 CA139A CA139A
R107 R108 RAD R109 12 P+7ECG RA159
U101D
VREFECGR
R103A C103 C104 C105 U111
RL
LP101 LAB RAB R134 R136 AD 4
C S1 U113B
R103 RD 5 8
S2 DOUT
LD 6 6
LL S3 U107E U114B
9 6 CD 7 7
S4 RA160
8 7 12 6 5
LA R110 R111 R112 R135 S5
LAD 10 LLB 5 RD 11 10 11 7
U101C U103B S6 PACE
10 5
RA S7
VREFECGR 9
R104A C107 C108 C109 R137 S8
P+7ECG VCCECG
13 P-7ECG RA163 RA161
LP102 V+
LLB
R104 3
V-
J101 VCCECG
RA 6 1 2 RA162
1 PACESE1 A0 ENB
LA 7 16
2 R113 R114 R115 R138 R140 PACESE2 A1
LL LLD 5 LAB 15 14 RA164 RA165
3 U101B A2 GND CA131
C CA138
4
RL VREFECGR
5 R105A C111 C112 C113 9
6 CA130
C120 P-7ECG 8
LP103 R121 LLB R139 10 LD U107B U107A
R105 U103C
4 3 2 1
11
R141
4
R116 R117 R118 U114A
U107F
2 2
VREFECGR 1 CB 1 12 13
R106A C115 C116 C117 3 3
U101A
LP104
R106
8
P+7ECG RAB R142
R122
CA136 VCCECG C174 P-5ECG
R119 R120 RLD LAB R143
C121
11
C153
LP105 C119 LLB R144 R146
2
R174 1
I
13 3
14 R173 U110A
CB R145 12 CD C166 P-7ECG
U103D R191 R193 C175 P+5ECG
4
11
R147
2
C150 1
R170 3 C170
VREFECG VCCECG U108A
RA137 R171 R172 P+7ECG
4
R192
C151 C152
C167
VCCECG
CA117 Q101
CA115 P-7ECG RA122
RA135 RAOFF
II
RB101
11
U110B
1
C157
D101 R178 6
2 7
RA121 II
CA105 1 5
RA111 RAB RA120 3 Q105 R179
U105A
R194
CA103 P-7ECG CA110 6
4
RA113 CA116 P+7ECG C154 7
RA136 VCCECG R175 5
U108B
RA125
4
U110C
1
C161
RA101 RAB VCCECG R183 9
8
RA128 III
9 10
RA102 LLOFF R184
LAB 8
LLB RA126 10
U105C RB103 R195
9
RA103 RAB CA112 C158 8
R180 10
RA127 U108C
RA104 LLB Q107
R181 R182 C172
RA133 Q104
Q109
1
DVCC P+5
L505
P-12 DP-12
L504
BLM41A800S
BLM41A800S
C523 C551
47u 16V C533 C534
U506
DP+12
3 1 R509
VIN ADJ
P+12 5.36K DP-12
VOUT
L503
BLM41A800S
R517
C518 C519 R508 100 P-5 P-7
2
1.21K
1
P+7
CON1 P-5 D507 P-7 C530 47u 16V
R515 1N5233 R520
C527
1
40.2k 40.2K
P+7
4
1N5237
C520 D509 P+5 P+7
1N5237 R514 2 R519 6
1 7
3 5
U508A Q505 U508B Q506
LM358 R516 LM358 R522
1k 1K
8
C521
47u 16v
DP+12
3 1
VIN GND
DP+12
PWRD P+12
VOUT
U504
1 3
+VIN +VOUT
2 4 GND
+VIN -VOUT
CON1
C515
2
C510 C511
1
DVCC
5 100u 25V
C506A C506 C507 COM
6
47u 16V 47u 16V COM
DVCC
6 1 R504
VCC A
4 2 10K
OUT C
5 3
R501 GND
10K
J501 DGND PC900V
DRXD
1
DTXD DGND DTXD
2
DVCC
3
DVCC
4
5
PWR
6 R503
* PWRD U503 2K C546
R502 1 6
A VCC Name UT4000F pro 5A1E02 Type
DRXD 1K 2 4
C OUT RXD
3 5
GND
C545 PC900V
22u 16V File No. Page of
PWR PWRD
L501
BLM41A800S
DGND
Date Date Date
P-5RESP P+5RESP
Y201 C201
1 2 3 4 5 6 R202
1K R203 R204
U201A 65536Hz U201B U201C 2.2K 2.2K
4069 4069 4069 R206 20K
R201 U202
1M 12 14 R205 20K
X0 X
13
X1
R207 20K
2 15
Y0 Y
1
Y1 R208 20K
P+5RESP P-5RESP 5 4
Z0 Z C205 C206
3
Z1
P+5RESP
6
INH
11
C203 C202 A
10
B
13 12 9 8 11 10 9
C
U201F U201D U201E C204 7 C207 C208 C209 C210
VEE
4069 4069 4069
P+7RESP
R222
C221 100
R216
2.2K
C211 U204 P-7RESP
RA 5 R217
RA
7 4 8 300
S1A DOUTA C222 R219 C224
6 5
U203B S2A 2.2K
R209 6 9
S3A DOUTB
634K TL064 7
4
S4A
P+7RESP P-7RESP P+5RESP U205
8 1 3
RG RG
+V -V
13 3 5 1
S1B V IN- REF R220
12 2 2 6 2
S2B ENB V IN+ VOUT U206A
11 10K
S3B
C212 10 3 TL064
S4B V-
LA 10
LA
11
7
8 14
V+
9 P+7RESP
R210 U203C R218 R221
634K TL064 1 C218 C219 C220 300 10K
RESPS1 RESPS1 C223
16 15
RESPS2 RESPS2 GND
C225
13 R223
C213 14 100
LL 12
LL U203D
TL064 C226
R211 P+7RESP R224
634K 10K P-7RESP
R215
100
C216 R225
10K R229 C227
4.99K R232 R233 12 C231
14 R236 R237
4
10K 10K
C215 13 1K 1K
RL 3 R226 U206D
RL R230 C228 C230
1 10K TL064
2 D201 R234
10K
R212 U203A 180K
634K TL064 R227 9
8 R235
10K
11
D202 10 10K
P-7RESP U206C C229
6 TL064
R214 7
100 5
C214 C217 U206B C234 R246 R245 RESP
C R213 TL064 CON1
C 40.2K 22K
22K R243
R242
1
VR201 115K
1.33K 200K 6
R224A 7
R244 RESP
C233 100K P-7RESP 5
P+5 P+5RESP P+7 P+7RESP R241 U207B
L201 L203 115K
100 TL062
BLM21B222S BLM21B222S C236
C235
4
C237 C238 C248 C241 C242 C246 U207A TL062
10u 16V 10u 16V 2
1
3
Q201
D203 Name UT4000F pro 5A1E02 Type
8
R238
RESPRE
1.54M
P-5 P-5RESP P-7 P-7RESP 1N4148
L202 L204
R239 P+7RESP
BLM21B222S BLM21B222S 47K File No. Page of
C239 C240 C247 C243 C244 C245
10u 16V 10u 16V
R302
22K P-5 P-5TEMP P+5 P+5TEMP
L302 L301
R301 T1OFF
BLM21B222S BLM21B222S
22K
C317 C318 C319 C320 C321 C322
10u 16V 10u 16V
Q301
2N3904
D301
IN4148
C301
U303
P+5TEMP 1 8
R317 IC COMP VR303
2 7 VREF
VIN IC 10K
VREF 47 3 6
TEMP VOUT
4 5
GND TRIM C315 C316
10u 16V
R307
4.7K P+5TEMP
R319
39K
R305
15K R320
C303 C305 C313 1K
R308 R318
2K U301 8.2K
4
S1
5 8 P-5TEMP
S2 DOUT
6
S3
7
S4 C312 D303
12
S5 IN4148
P+5TEMP 11
R304 S6
10 P+5TEMP P-5TEMP TEMP
S7
9
4
1
5
22K S8 U302
1
13 2
R303 V+
6
22K T2OFF TEMP
3 3
V-
1 2
TEA A0 ENB
16
7
TEA1 A1
15 14
Q302 A2 GND C307 C308 P+5TEMP
2N3904 C310
D302 C314
1N4148 C311
C302
VREF VREF
P+5
1
P+8 C351 P+5
P+5
13 R377
100
14
R365 IBP2_F
IBP2 12
56K C352 R366 IBP2 U310D C311 C312 C329 C330
27.4K
U306D
R364
1
13 10K
14 9 R367 R368 U310B P-8
47K R376
OUTB 12 8 100 5
R375 1M R376A
10 7
R363 U310C 6 1M P+5 C313 C314 C331 C332
10K R378 R378A
11K R369
D 10K D
750K 56K
R370 C356
IBP2 1M R374 D305 P-5
1M 1N4148
1
U307B R373
1M P+8 R379
U308_5 5 4.99K P-5
7 P-8 P-5
4
C354 U310A IBP2_P
6
3
R372 C353 1 D306
R361 R362 10K 1N4148
C360 R371 2 P+8
10K 2.2K
2K P+8
C355
1
11
C342 P+8
P-8
P+8 C345
R345
56K 13 R357
R346 100
C346 27.4K 14
IBP1_F
IBP1 12
IBP1 U309D C321 C340 C344 C358 C366
U305D
R344 U309C
1
OUTA 12 10K
14 9 R347 R348 U309B P-8
100 47K R355 R356
13 8 5 10K 1M P-8
10 7 R356A
1
R343 6 1M
11K R349 R358 R358A P+5 P-8
P+8 10K 56K P-8
750K
R350 C350
IBP1 1M R354 U308
C 1M D302 C
vcc
8
4
U309A IBP1_P
3 6
R352 LOAD CS/LD GND
10K C347 3
R341 1 4 5 U308_5
4
11
R342
2.2K
P-8
C341
P+5
C334 U306B
R336 R336A R337 R337A 5
U302B 7 OUTB
7
L304 R328 RV6 340K 340K 340K 340K
IN2+ 5 U304 P+5 P-5 6
20K 20K
P+5 900mH 7 3 OP07
CN2 6 6
2 RV5 C335 C336
1 RV4 R335A 20K
R326 R329
2 5K
IN2+ C322 C325 10K 20K C328 33K
3 R339
IN2- P-8
4
1
5
4 R324 R334 7.5K
2.2K R335
R323 57.6K 57.6K
11
100 P-5
IN2- L303 R331 P+5 R333 U306A R338 U306C
R325 20K 8.87K C337 C338 340K R340
900mH 2.2K 2 10
1 8 49.9K
3 9
P-5 R327 R332
B 10K 4.7K B
C333
4
4
U302A
R330 SG2
P+5 2 20K P+8
1
3 Q302 C315 R317A 340K U305B
C301 2N3904 R316 R316A R317 5
100u 16V C302 7 OUTA
RV2 340K 340K 340K
P+5 P-5 6
8
20K
RV3
P+5 20K C316 C317
R315A
33K
P-8 R319
P+5 R314 R315 7.5K
57.6K 57.6K
11
U301B R313 U305A R318 U305C
7
4
3 R306 R309 C309
IN1-
4
1
P-5 R312
A 4.7K A
C310
File No. Page of
4
U301A
R310 SG1
2 20K
1
3 Q301 Design Audit Approve
2N3904
8
1 2 3 4 5 6
1 2 3 4
U105 P+5
ADDOUT 15 20 U101
DOUT VDD
J101 SSTRB 16 ADSCLK 1 39 AD0 U104 U103
D SSTRB P10/T P00 D
ADDIN 17 ADCS 2 38 AD1 1 A0 10 11 AD0
5 DIN C108 C109 P11/T P01 OC A0 D0
DEV2 ADCS 18 ADDIN 3 37 AD2 ALE 11 2 A0 A1 9 12 AD1
4 /CS 10u 16V P12 P02 C 1Q A1 D1
DEV1 ADSCLK 19 SSTRB 4 36 AD3 5 A1 A2 8 13 AD2
3 SCLK P13 P03 2Q A2 D2
13 ADDOUT 5 35 AD4 AD0 3 6 A2 A3 7 15 AD3
2 AGND P14 P04 1D 3Q A3 D3
R103 162K SDI 6 34 AD5 AD1 4 9 A3 A4 6 16 AD4
1 IBP1_F SDI P15 P05 2D 4Q A4 D4
1 CLK 7 33 AD6 AD2 7 12 A4 A5 5 17 AD5
IBP1 CH0 C110 C111 CLK P16 P06 3D 5Q A5 D5
CON5 LOAD 8 32 AD7 AD3 8 15 A5 A6 4 18 AD6
C123 10u 16V LOAD P17 P07 4D 6Q A6 D6
2 9 AD4 13 16 A6 A7 3 19 AD7
C122 IBP2 CH1 VSS 5D 7Q A7 D7
PLU1 13 21 A8 AD5 14 19 A7 A8 25
R104 162K INT1 P20 6D 8Q A8
3 P-5 PLU2 12 22 A9 AD6 17 A9 24
C116 CH2 INT0 P21 7D A9
R106 23 A10 AD7 18 A10 21
P22 8D A10
R105 115K 4 P+5 SG2 15 24 A11 A11 23
C117 CH3 T1 P23 74HC373 A11
115K 10 C101 SG1 14 25 A12 A12 2
/SHDN T0 P24 A12
5 VCC 26 A13
CH4 C112 R101 P25
31 27 A14 RD 22
EA/VP P26 OE
6 4.7K 28 A15 WR 27
CH5 Y1 P27 WE
19 A14 26
22.1184M X1 CS2
7 18 20
CH6 X2 CS1
11 VCC
VREF 6264
8 9 10 RXD
CH7 RESET RXD
VCC P+5 11 TXD
TXD
C102 RD 17 30 ALE
L201 RD ALE/P
14 12 WR 16 29
DGND REFADJ WR PSEN
800u R102 U102
C114 4.7K 1 8 VCC
C MR WDO C
SG1 SG2 2 7
SG1 SG2 C113 C115 VCC RST
3 6 TXD
C214 C215 10u 16V GND WDI
4 5
10u 16V C118 C119 PFI PFO
C103
MAX813
VOUT
C218
C210 R220 4148 1N5240A C219 P+5 R209 4148 C222 C223
4
1.21K Text C216 10u 16V C220 10u 16V
6 U206B Q202 2 U206A Q203 D203
VCC P+8 7 2N3906 1 2N3906 1N5233
2
5 3
LM358 LM358
R208 R211
8
1K 1K
B B
P-12
J201 P-12
DRXD
1
DTXD
2
PWR U202
3
4 R204
6 1
5 VCC A
4 2 1K
6 OUT C
DGND 5 3 Q201
CON6 R201 GND
DPWR 10K R205 TXD
10K
Name UT4000F pro 5A1I01 Type
DPWR PWR U201 P+12 DTXD DGND
1 3 VCC
L204 +VIN +VOUT
2 4
+VIN -VOUT
100u VCC
File No. Page of
C203 C204 R203
C230 5 100u 25V PWR U203 2K
A C201 C202 COM A
6
100u 16V COM R202 1 6
A VCC
1K 2
C OUT
4 RXD Design Audit Approve
3 5
C205 C206 GND
8 100u 25V DRXD
-VIN
9 7
-VIN -VOUT
Date Date Date
DGND
P-12
1 2 3 4
1 2 3 4
D D
D4A
Q1
R1 9013
300
VCC RED
K1 POWER
R6 Q3
D4
Q2 9013 J1
R2 56K R4
9013 VCC
1 2
200 10K VDC 3 4
YELLOW R5
C 47K 5 6 C
KR1 KL2
7 8
ENCD1 KL1
R3 9 10
KR0 KR0 ENCD2
11 12
10K KL0 KR2
13 14
KR0 KR1 KR2 KEYBRD
VCC
R9 R10
20K 20K K2 ECG K5 AL K6 NIBP VDC VCC
J2 VCC
6 C2
ENCD2 C1
5
ENCD1
4
KL2
3
KL0
B 2 B
1
K3 FR K4 PRI K7 M
CODER
KL1
VCC
Name 5A1K01 Type
R13
1K2
D1 File No. Page 1 of 1
GREEN
D2 Design Audit Approve
A A
VDC
R12
2.1K
YELLOW
Date Date Date
1 2 3 4
1 2 3 4
J7 J5 J6
风扇电源 TXD1
1
TXA2
1
TXB2
1
U101 J10 RXD1 RXA2 RXB2
2 2 2
UA7810KC FAN TA212V
3 3 3
1 3 TD112V TB210V ECGVcc
Vin +10V 1 4 4 4
VCC TA2Vcc VCC
2 5 5 5
ECGVcc
GND
D 6 6 6 D
C101 J3
CON6 CON6 CON6
1 2
100u/25V J4
3 4
ECGRXD ECGRXD
2
5 6 1 2
U102 ECGTXD ECGTXD
7 8 3 4
16 1 ECGRXD ECGRXD
VCC C1+ C104 9 10 5 6
2 ECGTXD ECGTXD
V+ 11 12 7 8
6 3 IBPRXD IBPRXD
V- C1- 13 14 9 10
4 IBPTXD IBPTXD
C2+ 15 16 11 12
14
COM2RXD
T1OUT C105 17 18 13 14
7 5
T2OUT C2- 19 20 15 16
13
COM2TXD 11 CENRXD +5 -5
R1IN T1IN 17 18
C102 C103 8 10 HEADER 10X2
R2IN T2IN 19 20
J1 CON20 12 CENTXD IBPVcc
R1OUT C305 C306
15 9 HEADER 10X2
1 2 GND R2OUT
Vcc
3 4
U304
5 6
IBPRXD IBPTXD DGND1 DGND1
7 8
SPO2RXD SPO2RXD +5
C 9 10 C
IBPVcc IBPVcc 1 3
11 12 VIN VOUT
RXB2 TXB2 VCC U303
GND
13 14
ECGVcc ECGVcc U301
15 16
ECGTXD ECGTXD 7 6 -5
17 18 VCC +5OUT
ECGRXD ECGRXD 8 3 1 3
19 20 VCC -5OUT VIN VOUT
C301 C302
2
GND
J2 CON20 1 5 C303 C304
GND GNDD 104 104
TB210V TB210V 2
100u/25V 4
1 2 GND GNDD
DGND1
3 4
TD112V TD112V DGND1 DGND1
2
5 6
DGND1
7 8
TA2VCC TA2VCC J8
9 10
TXA2 TXD1 Q301 DGND1
11 12 2 1
RXA2 RXD1 VCC U302 2N3906 +5
13 14 R301 4 3
TA212V TA212V 6 1
15 16 VCC A 6 5
COM2RXD COM2RXD SPO2RXD 4 2 1K
17 18 OUT K 8 7 -5
COM2TXD COM2TXD 5
19 20 GND +5 10 9
DGND1
R303 12 11
B 2K 14 13 +5 B
R302 SPO2
10K
VCC DGND1 DGND1
C204
C202 VCC
VCC R207
300 Name 5A2J01 Type
R208
VCC U205 1.1K
J9
1
VCC A
8
1
File No. Page 1 of 1
DCENRXD 2 7
RO B 2
DCENTXD 3 6
DI Z 3
4 5
GND Y 4
A
PC Design Audit Approve A
R206 R209
1.1K RES2
1 2 3 4
1 2 3 4 5 6 7 8
R414 R418
U407 VCC 100K 100K
1 8 U402 U403
A0 VCC
2 7 R401 R402 U406 AD0 66 17 AD0 66 17
A1 WP D0 TXA D0 TXA
3 6 SCL 20K 20K U401 A8 1 15 CSA1 AD1 67 7 AD1 67 7
A2 SCL A Y0 D1 RXA D1 RXA
4 5 SDA RECSW 2 43 AD0 A9 2 14 CSB1 U405 AD2 68 8 VCC AD2 68 8
GND SDA P1.0 P0.0 B Y1 D2 RIA D2 RIA
NIBPSW 3 42 AD1 A10 3 13 CSC1 A0 10 11 AD0 AD3 1 10 AD3 1 10
P1.1 P0.1 C Y2 A0 D0 D3 DSRA D3 DSRA
4 41 AD2 12 CSD1 A1 9 12 AD1 AD4 2 12 R415 AD4 2 12 VCC
RECRXD P1.2 P0.2 Y3 A1 D1 D4 DTRA D4 DTRA
D 5 40 AD3 11 CSA2 A2 8 13 AD2 AD5 3 9 100K AD5 3 9 D
RECTXD P1.3 P0.3 Y4 A2 D2 D5 CDA D5 CDA
VCC TD1SW 6 39 AD4 4 10 CSB2 A3 7 15 AD3 AD6 4 11 AD6 4 11 R419
P1.4 P0.4 E1 Y5 A3 D3 D6 CTSA D6 CTSA
Y401 TB2SW 7 38 AD5 5 9 CSC2 A4 6 16 AD4 AD7 5 14 AD7 5 14 100K
P1.5 P0.5 E2 Y6 A4 D4 D7 RTSA D7 RTSA
2 1 IBPSW 8 37 AD6 A15 6 7 CSD2 A5 5 17 AD5
GND P1.6 P0.6 E3 Y7 A5 D5
R404 R403 SDA 9 36 AD7 A6 4 18 AD6 A0 34 19 A0 34 19
P1.7 P0.7 A6 D6 A0 TXB A0 TXB
4 3 10K 10K 74HC138 A7 3 19 AD7 A1 33 29 A1 33 29
VCC OUT A7 D7 A1 RXB A1 RXB
RXINT1 15 24 A8 A8 25 A2 32 28 A2 32 28
INT1 P2.0 A8 A2 RIB A2 RIB
30MHz RXINT0 14 25 A9 A9 24 26 VCC 26
L413 INT0 P2.1 A9 DSRB DSRB
VCC 26 A10 A10 21 WR 18 24 WR 18 24 VCC
L412 P2.2 A10 IOW DTRB IOW DTRB
SCL 17 27 A11 A11 23 RD 52 27 R416 RD 52 27
BLM21B222S T1 P2.3 A11 IOR CDB IOR CDB
BLM21B222S TA2SW 16 28 A12 U404 A12 2 25 100K 25 R420
T0 P2.4 A12 CTSB CTSB
C401 VCC 29 A13 AD0 2 19 A0 31 22 31 22 100K
P2.5 1D 1Q 16/68 RTSB 16/68 RTSB
35 30 A14 AD1 3 18 A1 RD 22 65 65
EA P2.6 2D 2Q OE INTSEL INTSEL
31 A15 AD2 4 17 A2 VCC WR 27 CSA1 16 51 CSA2 16 51
P2.7 3D 3Q WE CSA TXC NIBPTXD CSA TXC
21 AD3 5 16 A3 26 CSB1 20 41 CSB2 20 41
X1 4D 4Q CS2 CSB RXC NIBPRXD CSB RXC
L411 20 AD4 6 15 A4 A15 20 CSC1 50 42 CSC2 50 42
X2 5D 5Q CS1 CSC RIC CSC RIC
BLM21B222S AD5 7 14 A5 CSD1 54 44 CSD2 54 44
6D 6Q CSD DSRC CSD DSRC
RESET1 10 11 SYSRXD AD6 8 13 A6 6264 37 46 VCC 37 46 VCC
RESET RXD 7D 7Q RESET DTRC RESET DTRC
13 SYSTXD AD7 9 12 A7 39 43 39 43
TXD 8D 8Q TXDRY CDC TXDRY CDC
U408 RD 19 33 11 1 RXINT0 38 45 R417 RXINT1 38 45 R421
/RD ALE C OC RXDRY CTSC RXDRY CTSC
1 8 WR 18 32 WDI 15 48 100K 15 48 100K
//MR WDO /WR PSEN INTA RTSC INTA RTSC
2 7 1 34 74HC573 21 21
VCC VCC RST NC NC INTB INTB
3 6 WDI 12 23 C403 49 53 49 53
GND WDI NC NC L414 INTC TXD INTC TXD
4 5 22 44 55 63 55 63
PF1 /PFO GND VCC VCC INTD RXD INTD RXD
BLM41A800S 62 62
RID RID
35 60 35 60
XTAL1 DSRD XTAL1 DSRD
Y402 58 58
DTRD DTRD
3.6864M 61 61
C CDD CDD C
C404 36 59 36 59
XTAL2 CTSD XTAL2 CTSD
56 56
RTSD RTSD
1 2 3 4 5 6 7 8