Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Oilite® Bushes
Tolerances
T E C H N I C A L
METRIC STOCK TOLERANCES The standard operating range is -9°C to 70°C.
Plain Bushes:
Length L is js13. To prevent possible seizures with Stainless Steel or hard-chromium plated
Concentricity : Full indicated movement. shafts, an addition of molybdenum disulphide to the impregnation oil
D with respect to d: D <= 50mm, IT9 : D> 50mm, IT10. must be specified at extra cost.
Flanged Bushes:
Length L is js13. However, here are some basic rules:
Flange Thickness: e is js13. 1) Low viscosity oil for low temperatures, high speeds or light loads.
Flange Diameter: D is js13. 2) High viscosity oil for high temperatures, low speeds or heavy loads.
Concentricity: Full indicated movement. 3) High viscosity index oil for wide variations in operating temperatures.
D with respect to d : D<=50mm, IT9 D> 50mm, IT10. 4) Oxidation stable oils for long-period usage.
5) Oil with ‘oiliness’ additives for boundary conditions.
Chamfers: 45° chamfers are incorporated on inside and outside diameters 6) Oil of lesser ‘oiliness’ for full film (hydrodynamic) conditions.
at each end of the bush. Chamfer length varies with bush wall thickness 7) Oil with Extreme Pressure (E.P.) additives for very heavy or shock loads.
and outside diameter.
Fitting: before fitting make sure that all sharp edges are removed from
CAUTION: IN THE E.C. THERE ARE AT LEAST THREE ‘STANDARDS’ the housing and mating shaft. The bearing must be free from grit and dust.
COVERING DIMENSIONS AND TOLERANCES OF METRIC BUSHES. Wash in oil if storage conditions are in doubt and re-oil if held in stock for
All the metric (ISO) bushes in this catalogue are manufactured to the more than a year or if stored in contact with an absorbent material.
tolerances set out in ISO 2795 - plain bushes from sintered material. Always use steady pressure to insert the bearing. Never use hammer blows.
ISO 2795 is the standard used by the BSI for this type of bearing; it is also Shafts should ideally be hardened to approximately HRC 60 and ground to
widely used in other European countries. a surface roughness of Ra=0.25µm.
Bushes conforming to other metric standards used in the E.C. are available The standard metric range of Oilite® bushes to ISO 2795 is made to G7/s7
in Britain; bushes made to these other standards may not suit the ISO limits of tolerance. These bushes when fitted into a rigid H7 housing, using
2795 fitting requirements and vice versa. Incompatibility may result in an m5 fitting pin, will give an H7 bore, which when run on an f7 shaft will
bearing seizure or much reduced life, therefore great care must be taken in give good performance.
selecting matched bearing, housing, fitting-pin and shaft sizes. Storage: Oilite® bushes can be stored for considerable periods without
We can supply bushes to meet other standards. Quotes on request. deterioration or loss of oil if kept in a metal or other nonabsorbent
container, at room temperature. Proximity to heat could cause oil loss by
Lubrication: Standard Oilite® bushes are impregnated with highly refined sweating, in which case re-oiling is necessary before fitting.
mineral oil to ISO VG (SAE 30) having a high viscosity index and containing
anti-oxidant, anti-rust and defoamant additives. Re-oiling: after machining of the bearing, or following oil loss during
A replenishment of oil should be carried out after 1000 hours of use or storage, immerse in high quality mineral oil to ISO VG 60 or ISO VG 150
yearly. These intervals can be extended for bushes with relatively thick walls (SAE30 or SAE40) at 80°C to 100°C for 10 to 15 minutes and then cool in
and shortened for low porosity bushes. Bushes running submerged in oil cold oil.
or in oil-splash will not require replenishment. Plain And Flanged Bushes - Tolerances
Nominal Sizes Standard Tolerances
Flanged Bushes - Radii Over Up to IT9 IT10 js13
(between outside diameter and flange face) - 3 0.025 - ±0.070
Outside r 3 6 0.030 - ±0.090
Diameter max 6 10 0.036 - ±0.110
≤12 0.3 10 18 0.043 - ±0.135
>12 ≤30 0.6 18 30 0.052 - ±0.165
30 50 0.062 - ±0.195
>30 0.8 50 80 - 0.120 ±0.230
Nearest Equivalent Specifications
UK BS5600 France Germany U.S.A.
Part 5 NF 150 DIN
ISO 5755/1 Section 5.1 5755/1 30 910 M.P.I.F.
Material Grade 1987 1988 A95-771-1 PART 3 STAND. 35 S.A.E. A.S.T.M.
B438 Grd 1
MB01-1 P4011Z P4011Z FU-E10-60 - CT-1000-K19 840 Type 1
Oilite®
Bronze B438 Grd 1
MB01-2 P4012Z P4011Z FU-E10-64 Sint A50 CT-1000-K26 841 Type 2
Material Specifications
Chemical Composition Mechanical & Physical Properties
(2) Radial (1)
(4) Total (1) (1) Crushing Density Static
Other Open Oil Strength P Load (3)
MB C Elements Porosity Content K Min. Nominal Max. Pv Factor
Grade Total Cu Sn Max. P Min. Min. N/mm2 g/cm3 N/mm2 N/mm2 x m/s
MB01-1 <0.3% Balance 9-11% 2% 27% 24% 120 6.0 35 1.8
MB01-2 <0.3% Balance 9-11% 2% 22% 20% 160 6.4 50 1.8
Notes :
MB01-1: Applicable to bars, cored bars and plate material 1. Density, oil content and open porosity determined according to BS5600
MB01-2: Applicable to metric bushes. Pt. 3 Section 3.2 1988.
2. Radial crushing strength according to BS5600 Pt. 3 Section 3.9 1979.
Coefficient of Friction: Bronze on steel = 0.12 Static, 0.06 Dynamic 3. PV factor = Pressure(Nmm2) x bearing surface velocity (m/s) where
Other bearing materials for special applications are also available. pressure = load (N) / projected area (d x L) and d = inside diameter (mm).
4. Bars, cored bars and plates may contain up to 1°C.
Product information updated December 2018 and subject to change. Please click the product links for prices and availability.
BEARINGS
Oilite® Bushes
Fitting Data for Metric QM & QFM
T E C H N I C A L
R
ØDp ØB ØD
Fitted Bush
Product information updated December 2018 and subject to change. Please click the product links for prices and availability.
BEARINGS
Oilite® Bushes
Fitting Data for Imperial QT & QF
T E C H N I C A L
R
ØDp ØB ØD
ØdF ØDs
Fitted Bush
Product information updated December 2018 and subject to change. Please click the product links for prices and availability.