Sei sulla pagina 1di 7

2014 AE Licensure Exam

PART I

1. Situational Analysis (4 problems)


A. Machine
Bore-stroke ratio: 76:78
Torque: 2 kg-m
Speed, rpm: 1,000
Specific fuel consumption: ______
Find: a. piston displacement (cc)
b. power developed by the machine
c. fuel consumption (Li/hr)
d. fuel consumption for 2 hours (Li)
B. 100 ha of land
 30 ha of needs deep tillage
 20 ha newly plowed
 35 ha planted with rootcrops
 15 ha planted with corn and needs weeding
1. In 100 ha land, what depth of soil manipulation is needed (maximum)
a. 400 mm c. 200 mm
b. 300 mm d. 100 mm
2. What should be done in 20 ha land
a. harrowing c. bedding
b. plowing d. anchoring
3. What should be done in 35 ha land?
4. What should be done in 15 ha land
C. Performance of Threshing Machine
1. Maximum threshing capacity, kg/ha
2. Corrected capacity
3. Threshing recovery
4. Threshing efficiency
D. Market vendor (marketing)
2. Ratio of the drawbar power developed by the machine to the axle power
a. Mechanical efficiency c. tractor efficiency
b. Traction efficiency d. lugging efficiency
3. Head agency of AFMech in terms of Research, Development and Extension Network
a. UPLB c. PhilMech
b. DOST d. PCARRD
4. What is the size of the seal of PSAE?
Ans: 42 mm
5. 2013-2020 Road Map for Ag. Engg is approved in view of ___________
a. For food security
b. All of the choices
c. For ASEN community economic growth
d. For the implementation of Phil. Ag. Engg. Law
6. Pitot-static tube is used to measure _______
a. Static head
b. Pressure head
c. …..
d. Difference between the static and the dynamic head
7. What is commonly manufactured in the country?
a. Dryers c. water pumps
b. Farm engines d. ……
8. What is not manufactured in the country?
a. Corn c. rotary tiller
b. Coconut d. ……
9. Farm mechanization in the country is intensive in what crop?
a. Corn c. sugarcane
b. Coconut d. rice
10. Mechanization in the country was first introduced in what crop?
a. Rice c. coconut
b. Corn d. sugarcane
11. Obsolescence of rotary tillers can be accounted to?
a. Development of new technology
b. All of the above
c. ………….
d. Introduction of new tillers with high efficiency
12. A man borrows 10,000 from a bank and promised to pay after 4 months. Find the discount
rate if the bank gave him a discounted value of 8,000.
a. 20% c. 10%
b. 40% d. 80%
13. A type of negative displacement pump
a. Plunger pump c. ………
b. Pitcher pump d. centrifugal pump
14. Act of removing water vapor in the pump by filling it up with water.
a. Pumping c. pumping priming
b. Surging d. all of the above
15. According to Phil. Ag. Engg. Law, there shall be Ag. Engineer in each city, municipality,
or province in what office?
a. Engineering c. …………..
b. …………. d. agriculturist
16. How many Ag. Engineers should be present in the office?
a. More than 1 Ag. Engineer c. many Ag. Engineers
b. At least 1 Ag. Engineer d. less Ag. Engineer
17. In the Ag. Eng’g Road Map for 2013-2020, how many Ag. Engineers are needed
a. 30,000 c. 15,000
b. 20,000 d. 10,000
18. The hydraulic remote control hitch of the tractor should be how long?
a. 20-24 inches c. 9-18 inches
b. ………….. d. 6-12 inches
19. What are the two consecutive farm activities increases cropping intensity?
a. Planting-spraying c. harvesting-threshing
b. Harvesting-milling d. irrigation-plowing
20. What farm activity is least mechanized?
a. Planting c. harvesting
b. Plowing d. threshing
21. Problem: Gear setting of the machine
22. Problem: No. of plant population/ha
23. Density of premium gasolinr (kg/L)
24. Contents of AFMA and AfMech Law
25. Problem: Calibration of drum seeders
26. What is AFMA (RA 8455)
27. Problem:
 Capitalized cost (FC + annual maintenance)
 Simple interest
 Compound rate
 Annuity
28. DILG Memorandum Circular
 implementation of Phil. Ag. Engg. Law in SUCs
 signing of AEs in agricultural buildings & structures
 signing of AEs in farm-to-market road
29. Pump (static head, velocity head, dynamic head)
PART II

1. Type of precipitation in the Philippines (rain)


2. Geologic formation that transmits sufficient amount of water (aquifer)
3. Terrace used on moderate slope (6-8%)
a. Conservation bench broad terrace
b. No tillage
c. Bench terrace
d. Grass-covered terrace
4. Type of drain made along contours just like terracing
a. …….
b. Bedding system
c. Intercepting/cross-slope system
d. Parallel system
5. According to NIA, what must be the slope of the canal to allow machines to pass by:
a. 4:1 c. 1:1
b. 3:1 d. 2:1
6. Probability:
According to a doctor in a lung hospital, 70% of his survivor patients are chain
smokers. On that day, 10 patients went to the hospital, find the probability that less than
half of his patients are chain smokers.
7. Given the data: 0, 5, 1, 1, 1, 3. What is the mode?
8. Standard deviation is the square root of ____________
a. Variance c. median
b. Mean d. mode
9. The pressure of the soil at field capacity is _______________
10. The pressure of the soil at permanent wilting point is _________
11. A standard rain gage is used to measure the rainfall in a certain place. The outer tube used
to catch the rainfall is how many times bigger than the inner tube?
a. One time bigger c. four times bigger
b. Two times bigger d. ten times bigger
12. Type of rainfall due to warm air replaces the cold air.
a. Orographic c. cyclonic
b. convective d. barometric
13. The simplest (in terms of gadgetry) and most economical way of developing a well.
a. Jetting c. ____________
b. Surging d. ____________
14. Type of soil where groundwater movement is the fastest
a. Gravel and sand c. loam
b. Clay d. silt
15. What type of turbine needs to be filled with water to start working?
a. Impulse turbine c. __________
b. Water wheel d. __________
16. Janssen-Heissen formula for evaporation uses the principle of ________
a. Aerodynamics c. ___________
b. Aerodynamics and ….. d. ___________
17. Darcy’s Law of flow equation is only applicable in what type of fluid flow?
a. Laminar flow c. turbulent flow
b. Viscous fluid d. ideal flow
18. Darcy’s Equation of flow is only applicable on fluids with Reynold’s Number _____
a. Greater than 1.5 but less than 2 c. less than 1.5
b. Greater than 1 but less than 1.5 d. less than 1
19. IR 64 is a rice variety under ____________
a. Japocanica c. Japonica
b. Indica d. Javanica
20. Open channel problems
21. Triangular weir problems
22. Irrigation efficiency
23. Q=CIA
24. Thiessen Polygon Method
25. Equation of circle
PART 3

1. Which is the best description of a closed nipple?


a. Threaded outside the cap c. no threads at all
b. Threaded inside the cap d. threaded at the end caps
2. Which is not the rate of removing heat from a space or product?
a. Heat load c. Refrigeration Load
b. Cooling load d. Thermal Load
3. Given the EM frequency of _______×108 Hz and C=1.8×106, find the length travelled.
4. Quarter sawed lumber is best suited for finishing flooring because?
a. Greater strength c. easy to wax
b. Easy to handle d. minimum shrinkage
5. Type of motor where loop winding is parallel with the armature
a. Series-wound motor c. shunt-wound motor
b. Compound-wound motor d. single-wound motor
6. Material in greenhouse that is less expensive, resist rainfall and use less reinforcement
a. Screen c. glass
b. Polyethelene d. fiberglass
7. What is the moisture content of the saturated soil which has the properties
 Plasticity Limit = 27
 Plasticity Index = 29
 Liquidity Index = 0.3
8. Open channel which uses more reinforcement
a. Rectangular c. trapezoidal
b. Circular d. triangular
9. Which is not a function of PERT/CPM function
a. Budgeting c. control-monitor
b. Scheduling d. __________
10. In what soil are structures best built?
a. Sand and gravel c. clay loam
b. Hard clay d. compact and dry loam
11. In an AutoCAD window, what toolbar can be found above the displace screen?
a. Standard toolbar c. ____________
b. Draw toolbar d. modify object toolbar
12. An AutoCAD option where the object can be reverse
a. mirror c. array
b.offset d. ______
13. PAES: Peanut Sheller Recovery
a. 93%
b. 94%
14. PAES* Peanut Sheller Capacity
a. 95%
b. 96%
15. PAES: The minimum noise level outside the slaughterhouse during nighttime
a. 50 dB c. 45 dB
b. 60 dB d. 70 dB
16. PAES: The minimum space requirement for buck/ram using slotted floor type.
a. 5.0 m2 c. 3.0 m2
b. 4.0 m2 d. 2.5 m2
17. PAES: The minimum space requirement for layers above 22 weeks using slotted floor
type.
18. Heat transfer problems

Potrebbero piacerti anche