Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Welcome: j210mi10
Product: EXCAVATOR
Model: 320D EXCAVATOR FAL
Configuration: 320D & 320D L Excavators FAL00001-UP (MACHINE)
POWERED BY C6.4 Engine
Specifications
C4.2 and C6.4 Engines for Caterpillar Built Machines
Media Number -KENR6740-24 Publication Date -01/02/2014 Date Updated -12/10/2015
i02980077
Crankshaft
SMCS - 1202
S/N - L5Z1-UP
S/N - SKA1-UP
1 of 6 5/7/2018, 1:54 PM
320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED ... https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?return...
S/N - JPD1-UP
2 of 6 5/7/2018, 1:54 PM
320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED ... https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?return...
3 of 6 5/7/2018, 1:54 PM
320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED ... https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?return...
Illustration 1 g01357460
(1) Crankshaft main bearing journal
4 of 6 5/7/2018, 1:54 PM
320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED ... https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?return...
Illustration 2 g01357462
(2) Support the crankshaft in a set of vee blocks. Measure the runout dimension at the center journal.
Maximum runout ... 0.04 ± 0.10 mm (0.002 ± 0.004 inch)
Illustration 3 g01356072
(3) Crankshaft end play ... 0.100 ± 0.246 mm (0.0039 ± 0.0097 inch)
Replace the standard thrust plates if the end play exceeds the standard clearance. Three oversize thrust plates
are available as replacements if the end play still exceeds the maximum limit. Generally, the rear journal is
likely to be worn more rapidly than the front journal. If necessary, replace the rear thrust plate. Refer to Table
1 for oversize thrust plates.
5 of 6 5/7/2018, 1:54 PM
320D & 320D L Excavators FAL00001-UP (MACHINE) POWERED ... https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?return...
Table 1
Dimensions for Grinding of Crankshaft
Oversize Thrust Plates
Oversize Thrust Plate Oversize (front or rear) Oversize (front or rear) Tolerance
0.15 mm (0.006 inch) 33.15 mm (1.305 inch) 33.30 mm (1.311 inch) 0.039 mm (0.0015 inch)
0.30 mm (0.012 inch) 33.30 mm (1.311 inch) 33.45 mm (1.317 inch) 0.039 mm (0.0015 inch)
0.45 mm (0.018 inch) 33.45 mm (1.317 inch) 33.60 mm (1.323 inch) 0.039 mm (0.0015 inch)
Torque for the crankshaft pulley nut ... 707.5 ± 57.5 N·m (520 ± 42 lb ft)
The maximum temperature for installing the crankshaft gear is the following value. ... 250 °C (482 °F)
Copyright 1993 - 2018 Caterpillar Inc. Mon May 07 2018 13:54:34 GMT+0700 (SE Asia Standard Time)
All Rights Reserved.
j210mi10
Private Network For SIS Licensees.
6 of 6 5/7/2018, 1:54 PM