Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
JI-68002
JAZ EPOXY 200 Two Component Epoxy Topcoat
Application
DESCRIPTION: Method Airless Spray Air Spray Brush/Roller**
" Jaz Epoxy 200 " is a high quality two-component glossy Thinning
finish based on polyamide cured epoxy resin. It has heat (by volume)* (0-10)% (15-25) % (10-15)%
resistance property
Nozzle Orifice 0.015-0.021" 1.0- 1.5 mm N/A
RECOMMENDED USE:
• Recommended to use as a general purpose interior coating Nozzle Pressure 15 MPa
on steel surfaces for thermal protection up to 200 °C.. ( 2100psi) 29.0-43.5psi N/A
-Excellent heat resistance up to 200°C. * Depends on the weather condition at work place.
-Gloss finish. ** Recommended for stripe coat and small areas.
-Excellent chemicals resistance property.
-Excellent solvents resistance property. Paint System
-Excellent abrasion resistance. Primers: Self-priming or inorganic zinc silicate. For other
-Very good hardness. primers, consult Al-Jazeera TSD.
-Very good flexibility. Topcoats: None.
-Very good salt, alkali and acid solution resistance properties
Physical Constants: Film Thickness and Spreading Rate:
Finish: Gloss Minimum Maximum Recommended
Colour: Al-Jazeera color card
Volume Solid: 74% , ASTM D2697 (µm) mil (µm) mil (µm) mil
Viscosity: 95 KU (mixed paint)@ 25°C, ASTM D562 Dry Film
Specific Gravity: 1.2 (mixed paint)@ 25°C , ASTM D1475 Thickness (DFT) 75 3 200 8 100 4
D.F.T: 100 µ each coat Wet Film
Theoretical Thickness (WFT) 101 4 270 11 135 5.4
Spreading Rate: 7.4 m2/ ltr at 100 µ DFT
m2/l ft2/USgal m2/l ft2/USgal m2/l ft2/US gal
Full Cured: 7 days @ 25°C
VOC Values: 173 g/ ltr. Theoretical
Spreading Rate 9.9 395 3.7 148 7.4 296
Surface Preparation:
PRE-CLEANING: Application Condition
Remove all visible surface deposits such as grease, oils and The product should not be applied at temperatures below
soils with suitable detergent. Remove salt and other contami- 5oC Surface temperature must be a minimum of 3oC above
nants by washing using high pressure fresh water. Where dew point.
necessary, work to remedy or alleviate design or fabrication Relative humidity should not exceed 85%.
defects such as weld spatter, and where required smooth In confined areas good ventilation is required during applica-
weld seams and sharp edges before abrasive blasting. tion and drying.
NEW STEEL:
Refer to pre-cleaning, the surface must be prepared accord- Drying Time and Recoating
ing to Sa 2½ (NACE No.2/SSPC-SP 10) or Sa 2 (NACE No. Drying times are generally related to air circulation, tempera-
3/SSPC-SP 6) . ture, film thickness and number of coats, and will be affected
MAINTENANCE: correspondingly.
Refer to pre-cleaning, remove damaged areas using power
Temperature 25°C/77°F
tool cleaning to St 2 (SSPC-SP3) or by abrasive blasting to
Sa 2 (NACE No. 3/SSPC-SP 6), but Sa 2½ (NACE No. Relative Humidity 50%
2/SSPC-SP 10) is preferable. As an alternative; use water
Surface Dry 2 hours
jetting to WJ-2 (NACE No. 5/SSPC-SP 12).
Hard Dry 8 hours
APPLICATION GUIDE: Dry to recoat, minimum 8 hours
Application Data Dry to recoat, maximum* -------
Mixing ratio: By Volume
Base Hardener
2 : 1 Note: All records given in the table are typical at: recom-
Pot-life: 4 hours @ 25 °C. mended film thickness, good ventilation and one coat
Induction Time: Nil. system.
*The surface should be dry and clean prior to application.
Application Method and Thinning: The best time to recoat is before previous coat is cured. If
THINNER: Recommended thinner is “Al-Jazeera Thinner 505”. this time is exceeded, the surface may need to be
roughened slightly.