Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
•Almost all data has to be analysed at WCELL or WBTS level for the worst cells -> Evaluation over time and
–Cell Availability
–Failures due to Radio, BTS or transport
–Handover Performance
–Traffic
–Cell Resources
–Iub Signalling
•Some data is better analysed at RNC level->Here only the time evolution and RNC comparison is useful
–Failures due the RNC, Iu, Iur
–Iur, Iu, Relocation Signalling
Monitor Cell/Neighbour cells Availability - missing cell has impact to neighbouring cells performance also
1. Assess weekly average PLMN KPI performance to identify KPIs below targets
–Start from bigger picture assessment (PLNM -> RNC -> Cluster -> WCEL )
–Weekly average will smooth the performance and gives better accuracy of performance assess
2. Assess network performance at RNC/Area level to check if bad performance happens across netwo
–Compare different RNC/Regions Performance
3. Apply drill down approach to assess bad performing KPIs in WCEL level
–Identify the failure call phases
–Categorizing failure ratio or distribution of each counters (Radio, transmission, BTS, RNC)
–Identify main cause of underperforming KPI’s
4. Prioritize analysis
–Filter using high number of failures or high number failure ratio (weighting)
–Identify top 20/50 worst cells
5. Analyze failure distribution in the network topology (rural, RNC border, expressway)
6. Propose Solution for cells having network KPIs below KPI targets
Because of the large number of cells in the network, it is not feasible to analyse all the cells.
Good methodology is to list top 10-20 worst cells per region and to build and follow an action plan on those
•This required a part-time or dedicated tracking role
Either total number of failures or failure rate (%) could be used
•Coverage hole, missing neighbour or capacity problem
Typically CS and PS busy hours does not exist in the same time
•In example below, the PS Busy Hour is later in the evening (20-21 hours) than CS (15-16 hours).
During weekend CS data drops significantly while PS data is quite constant
The new smart phones such as Blackberry (RIM), iPhone (Apple) and N97 (Nokia) are loading the network in a new
•Applications which require ‘always on’ connectivity have become very popular in many networks
Fast dormancy or Quick Release will have impact to the load & performance
Call can be traced by using subscriber's IMSI, MSISDN or equipment’s IMEI number
Subscriber trace can be used for:
In system testing and provisioning phase for trouble shooting and network optimisation.
Jump User Id:
Jump password:
aluation over time and Comparison between large areas (Cities, RNCs) is still required
omparison is useful
performance assessment as daily performance varies a lot especially in unloaded network, gives more accurate picture of KPI
appens across network or only particular RNC/Area
5-16 hours).
Voice Access failure= RRC Setup & Access fails + RAB Setup & Access fails
Starting criteria for setup failure analysis
RRC_CONN_STP_FAIL_AC (dominant)
•Check UL Interference (R99 Noise Rise, RTWP- Cell Power Report), DL Power (HSDPA, R99 power) & Code occu
•UL Power Spikes -> Disable UL Admission Control to if the number of failures is critical (PrxTarget-> 30 dB), impleme
RRC_CONN_STP_FAIL_TRANS
•Evaluate Number of reconfiguration failure due the transmission-- Traffic_on_Physical_Medium_Sub-Layer & Iub C
•Expand the capacity or decrease the traffic offered to the site
For ATM based Iub
•Check COCO Configuration
•Use AAL2 Multiplexing in case of two WAM
For IP based Iub---•Check IP based route parameters (ZQRL;)/ IP_Route_Resource_Reservations Report
RRC_CONN_STP_FAIL_RNC
•Typically RNC fault or Incoming SRNC Relocation Failure (inter-RNC border)--- RNSAP/NBAP Signalling
•Iur Troubleshooting-- RNSAP_Signalling Report
•DMPG problem in RNC
•Required ICSU log tracing if no RNC fault or SRNC relocation problem
RRC_CONN_STP_FAIL_ICSU_OVERL
•ICSU overload
YES---RRC Connection Setup complete msg. sent from UE?---No (L1 Synchronization Fail/ RNC Internal failures)-- RRC Access
YES ( RRC Active fails-- a) Radio Fails---
b) Ue fails---
c) RNC Internal fails--
RRC Access failure reasons: RRC Active release can be due to-- ISHO, IFHO, SRNC Reloc
RRC_CONN_ACC_FAIL_RADIO (Dominant failure cause type)
• Perform drive test to detect if UL or DL coverage Coverage or interference-- Cell Power Report
–UL Coverage
§UL coverage(TMA/MHA chk), Interference-- Tilt / Missing Neighbor chk / best server Ec/No sh
–DL Coverage
§Tune SCCPCH Power if UE does not receive the RRC Setup Message from RNC./ Antenna tilt(CP
/ Coverage Optimization-- PRACH_Propagation_Delay Report
• If UE does not synchronize(L1)
–tune CPICHToRefRABOffset vs.Qqualmin (or Qrxlevmin)
–Due to Increased interference with HSDPA, this max radio link power for AMR (offset parameter) has been in
RRC_CONN_ACC_FAIL_MS
–UL Coverage
§Tune Cell Dominance (or CPICH) in order to balance UL and DL (if UL interference is not the ca
If RRC setup/access failure due to Radio/MS, it is also possible to check whether UEs are located at distance area or close
•Propagation delay counters from RRC measurement M1006C128-C148 reports call setup distance during RRC con
•This give hints that either cells has large coverage area (tall sites with over-shooting) or non-optimum cell coverage fr
RAB Setup fails occurs (due to AC, BTS, frozen BTS, Transp, Iur Trans, Iu-CS Trans, Iub AAl2 fails)-----
then RNC sends RANAP: RAB Assignment Response msg. to CN, sending appropriate failure cause.
RAB Active fails occurs (due to Radio, Iu, Iur, Iub, RNC internal fails)-----
RAB_CONN_STP_FAIL_TRANS
•Evaluate Number of reconfiguration failure due the transmission-- Traffic_on_Physical_Medium_Sub-Layer & Iub C
•Expand the capacity or decrease the traffic offered to the site
For ATM based Iub
•Check COCO Configuration
•Check RAB_STP_FAIL_XXX_IUB_AAL2, M1001C531-C533
•Use AAL2 Multiplexing in case of two WAM
For IP based Iub---•Check IP based route parameters (ZQRL;)/ IP_Route_Resource_Reservations Report
RAB_CONN_STP_FAIL_RNC
•Typically RNC fault or Incoming SRNC Relocation Failure (inter-RNC border)--- RNSAP/NBAP Signalling
•Iur Troubleshooting-- RNSAP_Signalling Report
•DMPG problem in RNC
•Required ICSU log tracing if no RNC fault or SRNC relocation problem
RAB_CONN_STP_FAIL_ICSU_OVERL
•ICSU overload
RAB_ACC_FAIL_XXX_MS
•Evaluate Cell resource Prx and Ptx (for example high uplink interference)--NRT_Radio_Bearer_stats report for
•Check RB reconfiguration failure ratio ( If ATO setting is insufficient , rec. 500ms)--- RRC signalling report
Packet calls starts with user plane capacity allocation (transfer from FACH/PCH, DCH 0/0) and ends with dedicated resource re
There are counters for the following channel combinations
•Rel99 DL = DCH UL = DCH
•HSDPA DL = HS-DS UL = DCH •There could be multiple packets inside single R
•HSUPA DL = HS-DS UL = E-DCH • RU20 introduce Direct resource allocation for H
HSDPA Setup fails reasons: RNC, BTS, Iub, UE, UL-DCH, Multi-RAB, Max. users, DL Pwr limits.
HSDPA
HSDPA Setup fails reasons: RNC, BTS, Max. users, UE, E-DCH not selected due to too many hsupa users, AC Fails.
HSUPA
ation-- PRACH_Propagation_Delay Report
PrxNoise value between -99.5 dBm and -103.5 dBm. In Tmo=-105dbm(Nokia default=-105dbm)
ls)--- then sends RRC connection setup reject msg.
A, R99 power) & Code occupancy if there is need to upgrade radio capacity-- [ HSPA no. of Users ] Cell Utilization/capacity Report
rxTarget-> 30 dB), implement TN159
unters in order to evaluate lack of Channel Elements-- NodeB Utilization/CE Utilization Report
Example
Short One day dat-- to show top 10 sites having highest number of BTS fa
Medium_Sub-Layer & Iub Capacity reports •Majority of BTS Failures is coming from few sites.
•Check CE usage for these sites - > add CE capacity if needed or try to re
One site detail analysis show that Average UL CE usage ratio is above 90% causing high blocking ->
eservations Report
tem reset/user reset & DSP_Service_Statistics reports
NBAP Signalling
U overload
l Power Report
Missing neighbor
from RNC./ Antenna tilt(CPICH checks--
RSCP should notfor neighbor optimization
be<-102dbm) /
ffset parameter) has been increased (0-> -2 dB->-4 for networks with lot of smartphones)
ently restarted and the maximum number of RRC connection establishments is limited until a guard timer expires.
w Connection/bearer ]
A, R99 power) & DL Code occupancy if there is need to upgrade radio capacity-- [ HSPA no. of Users ] Cell Utilization/Capacity Report
rxTarget-> 30 dB), implement TN159 Number_of_HSPA_Users_and_UE_capability report
nd R99 users
ffic_Amounts_(R99_+_HSPA) report
n be also monitored-- Node B utilization/ HSPA Overview/
of_HSPA_Users_and_UE_capability/ MAC-hs_Retransmissions_by_Code_and_Modulation_Usage reports
unters in order to evaluate lack of Channel Elements-- NodeB Utilization/CE Utilization Report
eservations Report
NBAP Signalling
U overload
Use AAL2 Multiplexing in case of two WAM, Iub Capacity report, NRT_Radio_Bearer_stats--AAl2 congestion
io_Bearer_stats report for Prx & Ptx ratio –UL Coverage tuning
RC signalling report §Tune Cell Dominance (or CPICH) if the cause is UL inter
–DL Coverage tuning
§Tune SCCPCH Power if UE does not receive the RRC S
l Power Report
from RNC./ Antenna tilt(CPICH RSCP should not be<-102dbm) /Missing neighbor checks-- for neighbor optimization
s with dedicated resource release (transfer back to FACH/PCH, DCH 0/0, RAB release, outgoing relocation, HHO, ISHO)
tilization/capacity Report
P_FAILfailure)
urations on SRNC side
e allocation)
r CPICH) if the cause is UL interference
, HHO, ISHO)
PA_Users_and_UE_capability report
b---- Number_of_HSPA_Users_and_UE_capability report
eband schedular
edular type license
ettings on the site.
waste baseband capacity if schedulers are underutilized.
io resources
unts report-- for HS-DSCH
y HSUPA users
reached – new HSDPA connection is rejected due too many HSDPA users
Total_Numberof_RadiLnks
SHO_verhad10% 1
1.1.1.1.1. Retainibility Analysis (CS/PS/HS)
Voice Drop Call Optimization:
1. Monitor Daily Performance Reports/KPIs Worksheet---Pick Worst Offenders
2. Identify DCR top offenders…. few cells?…. Any particular area ? Known Coverage issue? Need a new site ?
3. check cell & its neighbor cells availability (availability should be 100%)---- cell level report
4. Check current alarms on the site / sector & same for neighbor cells?--- alarm history especially for transmission issues
6. Check if the sector is dropping the calls due to RF (Radio fails)-- Not RF(Iu, Iur, BTS, RNC, MS, CIPH, UE, trans fails)
7. If not RF, check :
• Voice Drops due to Iu
Check core network parameter setting if RAB_ACT_FAIL_XXX_IU
Check SCCP SGSN/RNC IuPS Tias/Tiar if RAB_ACT_FAIL_BACKG_IU
•Evaluate NBAP counters (radio link reconfiguration failures)-- NBAP Signalling Per cause Report
•Expand the Capacity or decrease the traffic offered to the site--- Check Uplink CE Usage(shouls not be >80-85
7. If drops are due to RF (Voice Drops due to Radio fails), check the Site location, Neighbors, Cell to cell HO stats(SHO,IFHO
Number_ofBstServ_RadioLnks
Need Tilt / Azimuth change to improve the area?
–UL Coverage
§UL coverage(TMA/MHA chk), Interference-- Tilt / Missing Neighbor chk / best server Ec/No sh
–DL Coverage
§Tune SCCPCH Power if UE does not receive the RRC Setup Message from RNC./ Antenna tilt(CP
/ Coverage Optimization-- PRACH_Propagation_Delay Report ( Cell range in TMO Sites-20Kms)
If No cell found ratio is>90% & enough ADJIs--- Wrong reference Clock tuning( 10MHz tunning)
If No cell found ratio<40% & ISHO Success rate<90%----- Investigate 2G
TCH Blocking/TCH congestion/TCH failures/2G traffic/2G covera
5. Detecting DL or UL path loss problem if RAB drop due to radio (dominant call drop cause > 50%)
–Check ASU failure rate (UNSUC_ASU) which link to NO RESPONSE FROM RLC
–Mapping radio failures with Tx power and CPICH related parameters -> CPICHToRefRABOffset
–Check Call reestablishment timer -> T315 (rec.10s)
–Ecno distribution for bad coverage issue (M1007C38-M1007C47)
RRC active drops reasons:
Iu
Iur
BTS
RNC
MS
CIPH
UE
Trans
Ciphering
Radio fails
PSSR rate can be monitored separately for R99, HSDPA and HSUPA
HSDPA Retainability •The normal transition from HS-DSCH to FACH/DCH are considered as a normal HS-DSCH rel
HSDPA Drop reasons: RL fails, Non-RL fails, Mobility fails, Pre-emption fails, other fails 1. RL Fails-
HSUPA Drop reasons: RL fails, Non-RL fails, E-DCH RelRate(HS-DSCH SCC), other fails
Drop Call Rate (DCR)
Call Drop rate (CDR) is calculated based on RAB activation failures
• Call is dropped if one (or more) of the following RAB, RB or RL, drops.
Need a new site ?
cause Report
CE Usage(shouls not be >80-85%--- NodeB Utilization/CE Utilization Report)
AP/NBAP Signalling
System reset/user reset & DSP_Service_Statistics reports
3, •Use AAL2 Multiplexing in case of two WAM, Iub Capacity report, NRT_Radio_Bearer_stats--AAl2 congestion
rs, Cell to cell HO stats(SHO,IFHO,ISHO), PRACH delay distance and Ec/No quality distribution statistics
ghbor chk / best server Ec/No should not be less than -12db Coverage or interference-- Cell Power Report
Missing
sage from RNC./ Antenna tilt(CPICH RSCP should not be<-102dbm) / neighbor checks-- for neighbor optimization
ites-20Kms)
too small SHO may fails and if too big capacity is wasted
dered as a normal HS-DSCH release (including transitions due to mobility and pre-emption) HS-DSCH Allocation release
Compare RL fails with -- Cell Upd ATT RL Fails & Cell Upd ATT RLC Fails--recoverable error ( present in retainability report)
Check SCC Failure rate--HSPA_Serving_Cell_Change report (HSDPA SCC fails due to UE,BTS,Trans,AC)-- high SCC failures le
Radio fails -- UL coverage(TMA/MHA chk) & Interference
DL coverage & Interference-- PRACH delay range report/tilt
Neighbor Optimization etc.
Iub -- HSPA Overview report-- for Iub congestion
RAB_ACC_FAIL_Iub AAl2 fails--- •Check RAB_STP_FAIL_XXX_IUB_AAL2, M1001C531-C533,
•Use AAL2 Multiplexing in case of two WAM, Iub Capacity report,
NRT_Radio_Bearer_stats--AAl2 congestion
Iub_Traffic_-_FP_layer report-- for rejections, discarded frames & lost PDUs with reasons
CE resource congestion--- CE utilization/Cell capacity/Number_of_HSPA_Users_and_UE_capability(Simultaneous us
Check Active_Set_Size_for_NRT-RT_Traffic report-- Active set update fails, 1-2-3 cells (% & no.) in active set for different R
Check HSDPA FMCS Mobility Control Parameter --(Add/Drop window, handover or SCC too late, SCC parameter)
Check call re-establishment T315 timer due to radio link failure 9 (60 secs in TMO)
A MAC-d flow
operations- RL fails(SRNC,DRNC), RL setup for HO failures, SRNC/DRNC(SHO/HHO-BTS not respond/other cause)
troubleshooting ?
for NRT traffic E-DCH Allocation release
HSPA Overview report -- HSUPA(2ms/10ms TTI thp, E-DCH 2ms TTI utilization), HSUPA Transmitted Power Ratio, H
usage( happy Bit rate, 2ms/10ms TTi trans usage rate, MAC-e PDU not transmitted/not received correctly/ceived c
but lost)
Number_of_HSPA_Users_and_UE_capability report -- hsupa simultaneous users, hsdpa/hsupa user distribution
Traffic_on_AAL5 report
2 congestion
tenna or MHA problem?
AL2, M1001C531-C533,
Us with reasons
_UE_capability(Simultaneous users, NRT DCH select due to too many hsdpa/hsupa users)
alling report
o_Bearer_stats report for Prx & Ptx ratio
UPA Transmitted Power Ratio, HSUPA
/not received correctly/ceived correctly
SHO_Adjacencies
SC_INTRABUEFLSC_INTRBUEFL
•SHO success rate KPI (RNC_195a) is informing how many successful Active set updates we will have, compared
Check SHO KPI if performance < 90% ( leads to Radio failure)--- Yes
–Check if cells are at RNC border
Yes-- (check Iur capacity and SRNC relocation problem)
No-- SHO_Adjacencies(46)--neighbor add/delete, Soft_Handover_Performance(28), Active_Set_Size_for_NRT-RT_T
–Detect badly performing neighbours using HO success rate per adjacency counters-- delete/
Total _ Number _ of _ Radio _ Links
SHO _ Overhead 100%
SHO Update Attempt RT Same, SHO success ratio RT increased from 99.8 to 99.9% and above.
RAB Attempts CS Voice same, RAB Success ratio CS Voice increased from 99.4 to 99.6%.
1. CM start possible?--No( Ch
If No cell found ratio >40%-- 3G cell at inter-RNC border/ 3G cell covers a coverage hole---- RF & ISHO neighbor optimiz
If No cell found ratio is>90% & enough ADJGs--- Wrong reference Clock tuning( 10MHz tunning)
If No cell found ratio<40% & ISHO Success rate<90%----- Investigate 2G
TCH Blocking/TCH congestion/TCH failures/2G traffic/2G cove
ISHO Cancellation
•The inter-system measurement phase takes a few seconds and during that time the conditions in the WCDMA layer m
–Event 1E cancellation
–AS Update (1A or 1C) can also cancel ISHO in case of RSCP or Ec/No triggered ISHO
§If the CPICH Ec/No or the CPICH RSCP of this cell is found to be greater than or equal to the thres
•No cancellation once measurement phase is completed
Parameters:
•Activation per RNC required with parameter RNC: ISHOCancellation
•Enabled per trigger reasons with parameters FMCG: ISHOClcauseXXX
•Parameter FMCG: DLDPCHTxPwrClOffset allows to influence cancellation (-3 in TMO)
•RNC: MaxNumISHOClPerAS sets the maximum number of ISHO cancellations per UE and per active set
ISHO Parameters
CPICH RSCP (Event 1F)
Thresholds:
HHoRscpThreshold DL DPCH power
HHoRscpCancel Threshold:
L3 filter: HHoRscpFilterCoefficient GsmDLTxPwrThrXX
Timers: Data rate threshold
HHoRscpTimeHysteresis HHOMAxAllowedBitrateDL
HHoRscpCancelTime
(XX=AMR,CS,NrtPS,RtPS)
3. Decision Algorithm
AdjgTxPwrMaxTCH
AdjgRxLevMinHO (n)
GsmMeasAveWindo
1.Triggering w
2.GSM measuring
3.Decision
Handover
Execution
2G-to-3G back
prevention
GsmMinHoInterval
There seems not to be a relation with poor SCC success and HSDPA retainability.
SCC success rate for HSDPA and HSUPA is not very accurate in cell level as denominator is incremented in the source cell (old
pdates we will have, compared to initial Addition/Replacement/Deletion requests.
pdate % - 1a,1b,1c, Events Ratio RT+NRT, HSUPA SHO Success Rate, CPICH EcNo Report(in % & no.) - Excellent, good, Acceptable, Poor, Ba
ss Rate, Target cells without neighbors are checked with their attempts & SR, Also their Avg. EcNo & RSCP shown their,
.---- ADJs addition & deletion of neighbors with no share
too small SHO may fails and if too big capacity is wasted
New value for ReplacementWindow for Event 1C must be set in relation to events 1A and 1
•FMCS: increase ReplacementWindow
–The amount of the ReplacementWindow increase depends on AddWindow and DeletionWindow s
No exact value can be given.
–AdditionReportingInterval
–ReplacementReportingInterval
–DropReportingInterval (RU10 parameter)
•Increase the interval of the periodical measurements or disable periodicity to make reporting event based
–Event 1C measurements are long, each occupying 160-200ms air interface time
–If the measurement interval is too short, the whole UL SRB bandwidth will be easily fully occupied
–Recommended way is to increase the interval from 0.5s to 1.0s
T and NRT parts
s simultaneously
If Max. Output power of UE is < value of AdjgTxPwrMaxTCH parameter; RNC adds Power diff(db) to AdjgRxLevMinHO -- 0...43 dBm, step
GSM neighbor cell must exceed the RSSI level of AdjgRxLevMinHO-- for a handover to be possible----- ( set as -95dbm in TMO)
value for handover nikallegi---- 1...32 MeasRep, step 1 MeasRep, (6 in TMO)
UL Quality
Timer
ULQualDetRepThreshold
Data rate threshold
HHOMAxAllowedBitrateUL
-3G back
ntion
smMinHoInterval
an be started without new inter-system measurements in compressed mode.
Multiple BSIC identification can be enabled with The MultipleBSICIdent parameter which must be set to ‘on’ to enable the feature across
The MaxBSICIdentTime parameter limits the maximum time for BSIC identification measurements per cell. If during this time no handove
•The MaxBSICIdentTime parameter must be configured with a value of greater than 0
•Suggested valued for testing of MaxBSICIdentTime is 3 or 4 seconds if the overall procedure of HandOver to GSM is close to typi
•Feature is applicable to both CS and PS connections so parameter is applicable in both RT and NRT FMCG parameter sets (although BSIC
remented in the source cell (old serving cell) and numerator is incremented in the target cell (new serving cell).
Determine
### SCC success rate, SCC failure rate and failure cause distribution
Check
###target cells HSDPA Setup performance (M1002C401 – M1002C428) if source cells SCC failure rate is high
•To find out which target cells are causing the SCC failure
If high
###SCC_FAILED_due_to_AC
•Check target cells M1000C22 AVE_PTXTOT_CLASS_4 and M1000C20 AVE_PTXTOT_CLAS
•Check target cells number of simultaneous active HSDPA users
If high
###SCC_FAILED_due_to_BTS
•Check target cells M1002C416/424 SETUP_FAIL_BTS_HS_DSCH_XXX
•Check target cells CE resource utilisation at BH using M5001 counters for lack of UL return ch
•Check NBAP Radio Link Reconfiguration Failure rate
•Check SHO overhead – all branches must have enough CE capacity if UE is in SHO when H
If high
###SCC_FAILED_due_to_UE
•Check target cells M1002C415/423 SETUP_FAIL_UE_HS_DSCH_XXX
•Check RB reconfiguration Failure rate
•Require ICSU troubleshooting for UE types monitoring
6.If high SCC_FAILED_due_to_TRANS
•Check target cells of M1002C414 SETUP_FAIL_IUB_MAC_D_INT or M1002C422 SETUP_F
•Evaluate number of reconfiguration failure due the transmission
•Check M1005C128 CANC_ADD_SRNC_TRAN_STP_FAIL
•Check M1001C531-C533 RAB_STP_FAIL_XXX_IUB_AAL2
7.If high SCC_FAILED_due_to_Others
•Check RNC internal transport resources usage (DMPG)
•Require ICSU troubleshooting
lent, good, Acceptable, Poor, Bad
shown their,
elation to events 1A and 1B
HandOver to GSM is close to typical value of 10 sec (GsmMeasRepInterval * GsmMaxMeasPeriod); visible benefit in reducing CM.
G parameter sets (although BSIC verification is not always required for PS connections)
e cells SCC failure rate is high
M1000C20 AVE_PTXTOT_CLASS_3 if SCC failures due to the lack of DL power (SCC_Failed_due_to_AC) – this is not visible in HSDPA a
DSCH_XXX
counters for lack of UL return channel resource
WBTS licenses
-Baseband capacity (license controlled in FlexiBTS up to HW limit)
Number and type of HSDPA schedulers -- HSDPA shared schedular(in TMO)--HSDPA 48 Users per Cell
Number of HSUPA schedulers-- (HSUPA Basic 24 users per BTS enabled in TMO)
-Local cell grouping and capacity allocation between local cell groups
-Cell maximum RF power
-Antenna line properties (MHA gain, feeder loss, RX diversity branch,…)
WCEl parameter-- Cell range- 5000, 10000, 20000 (mts) If Cell range is= 5000;
PRACH Propogation Delay report If Cell range is= 10000
Class 0 to Class 20 tak hoti hai If Cell range is= 20000;
Any errors or mismatches between planned setup, configured setup, and actual hardware on site may lead to performance deg
WBTS configuration can be checked using WBTS site manager:
WBTS configuration files can also be collected using a tool such as FileCollectorTool:
https://twiki.inside.nokiasiemensnetworks.com/bin/view/SEM/CommandlineTools
It collects site configuration data (including commissioning data and licenses) to xml files which can be mass post-processed.
Collecting the data takes quite long time as the tool automatically logs to every WBTS to copy the data, but it can collect all the
EL parameter PRACHDelayRange when the last RRC Connection Request or Cell Update of the measurement interval was received.
in NSN RAN
te may lead to performance degradation.
SUM
RNC_ 978b_AveragePRACHMessageLoad
DENO
RACHCapacity parameter- HW capacity reserved for a RACH transport channel in the BTS.
•RACH Capacity is indicated as the capacity of BTS to decode RACH messages in a 10 ms radio frame
•also Defines the number of PRACH preamble signatures used
•Range 1,2,3,4 (messages) and default = 2
•Recemmended value:4
For example if the RACHCapacity = 2 (default) then it means that the BTS can decode 2 RACH messages in every
S-CCPCH Configuration 1
The load of different transport channels (FACH-u, FACH-c and PCH) can be monitored separately
RNC_2029b FACH-u Load
RNC_2030b FACH-c Load
M 1006 C 25 _ PA
Paging Att empts per Cell M 1006 C 25 PA
M 1006 C 27 _ P
Example:
•The average PCH Throughput approaches 7kbps several times per day
•It is a clear symptom of PCH congestion during the traffic peak hour.
•Average PCH Load equal to 80..90% at RNC≡LAC level
•It is a highly congested situation, a high rate of missing pages is expected and LAC splitting needs to be plan
•The Paging success rate starts to decrease when PCH throughput exceeds 4-4.5kbps, that is a PCH Load of 5
•Threshold of 50% PCH Load confirmed as Rule of Thumb to trigger PCH Load optimization
Recom
Def/Cu
mende
Parameter Name (Cell level) rrent
d
N300 3 2
2000m 2000m
T300 s s (10)
Curren Recom
Parameter Name (RNC level) t mended
WaitTimeRRCconversational 3 2
WaitTimeRRCstreaming 3 2
WaitTimeRRCinteractive 5 8
WaitTimeRRCbackground 5 8
WaitTimeRRCsubscribed 3 3
WaitTimeRRCemergency 1 1
WaitTimeRRCinterRATreselectio 3 3
WaitTimeRRCregistration 5 5
WaitTimeRRChighPrioritySignalling 1 2
WaitTimeRRClowPrioritySignalling 5 2
WaitTimeRRCunknown 1 2
WaitTimeRRCother 0 2
•Reactive Measurements
–Setup Failures due AC
▪RRC/RAB setup failures
▪PS Call setup failures due AC
–HSDPA setup failures
▪Setup failures due UL DCH
▪Max. Number of HSDPA users reached
–Rejection rates in downlink and uplink
▪SRB, AMR, CS data, PS data, separately for UL and DL
–Low HSDPA throughput
–Channelisation code blocking rate
•Proactive Measurements
–Common channel Load (RACH, FACH, PCH)
–R99 Usage - Overview of cell loading status in UL/DL for R99 traffic only
–HSPA throughput limitations
▪HSPA Power & Usage
–Channelisation Code utilisation
–Simultaneous number of HSDPA users
R99 Usage:
UL Capacity Issues:
•UL admission control start blocking incoming traffic if the RTWP (Received Total Wideband Power) and controlled pa
–For years this has been solved by increasing the targets of the AC but now in 3G
•1 UE transmission interferes the other UEs
–One problematic connection can make the other UEs increasing the tx power and the cell starts breathing
▪the coverage decreases as the UEs in the cell edge run out of tx power
•The control must be returned to 3G network by decreasing the AC targets and blocking the traffic in a controlled way
System Noise
•System noise (WCEL: PrxNoise) is the sum of all stationary noises;
–thermal noise
–interference caused by spurious emissions of other systems,
–noise caused by additional equipment such as repeaters
•PrxNoise can vary place to place and even time to time
•PrxNoise is a RNP parameter whose setting affects the capacity of cell
–PrxNoise too low: overestimation of cell load and can lead to unnecessary call blocking
–PrxNoise too high: underestimation of cell load and can lead to overload situation
Wrong Prx Noise level causes error to estimated power in PIE (Power Increase Estimation) and PDE (Power Decrease
Autotuning Prx noise:
•PrxNoise is updated by the autotuning algorithm which adjust Prx Noise level automatically. Enabled with PrxNoi
PrxNoise autotuning step sizes is limited by PrxNoiseMaxTuneAbsolute parameter (by default not limited)
•Recommended parameter value is 2 dB. Value 2 dB allows 4 dB range in Prx Noise autotuning functionality. In t
•It is important to verify that prxnoise in the unloaded cell is close to -105 dBm. If that is not the case the cell needs further inve
PrxTarget is defined relative to PrxNoise.
–M1000C12 Maximum PrxNoise Level
–M1000C13 Minimum PrxNoise Level
•PrxTarget is scheduling targ
Uplink Scheduling •Prx_Target_PS is used for N
oad includes:
–RACH pre-amble
–RACH-c and RACH-u load
–FACH-c and FACH-u load
–PCH load
–SCCPCH power load
d of each cell needs to be measured, for example FACH-c, FACH-u and PCCH transport channels can be multiplexed into sam
mble load depends upon the no. of UE making use of RACH transport channel.
hannel may be used for the transfer of either user plane (RACH-u) or control plane (RACH-c) information.
load can be reduced by:
sing the number of available PRACH preamble signatures
sing the number of available PRACH access slots
sing the number of available PRACH
whether a large amount of signalling generated by cell, URA, location area or routing area updates. If so, consider adjusting the area bound
te whether or not there is excessive user plane data transfer within CELL_FACH. If so, consider reducing the RLC buffer thresholds that trig
ding the BTS configuration in terms of an additional carrier
n the BTS.
ages in a 10 ms radio frame
S-CCPCH Configuration 2
PCH Bit Rate is limited to PCH bit rate to 8 kbps •PCH24kbpsEnabled is configured to enabled with this configuration
with the FACH-u and FACH-c •PCH bit rate is increased to 24 kbps
•PCH is allocated its own separate S-CCPCH
ransfer the FACH-u and FACH-c bit rates •SF128 is allocated to the PCH to support the increased bit rate
PCH bitrate of 8 Kbps RU20 support PCH bitrate of 8kbps and 24 kbps
its & carry a single paging record per TTI (10 ms TTI) –Transport block size of 240 bits & 10 ms TTI
e broadcasted per 10 ms TTI –24kbps paging channel require activation of second SCC
aximum 100 UEs per second
çè max 100 Pages/s per cell 24Kbps paging Channel - Impact to Code and power capacity
•HSDPA cannot use 15 HS-PDSCH codes when HSUPA 2 ms TTI is ena
(B/coz Channelisation code for 24 kbps PCH uses a larger section of the
onds, including 0.5s sampling period) with the common channel information
LOAD
%
M_0
f too high Paging Load a considerable percentage of paging messages could get lost causing a bad user experience (‘non-reachability’ of U
traffic, LAC oversize,…).
CPCH Configuration 1, we know that S-CCPCH can be shared with the FACH-c and FACH-u but PCH always has priority.
that high Paging load has an impact upon FACH capacity when single S-CCPCH is configured.
.5kbps, that is a PCH Load of 50-55% approximately and is below 90% when PCH throughput exceeds 6kbps
optimization
24 kbps Paging Channel feature can increase the paging channel capacity three times higher from the 8 kbp
So PCH throughput is increased- 24 kbps PCH
When the amount of paging messages exceeds 50% of the nominal capacity, its good time to start thinkin
ell can page 100 UEs/sec •50 msg/sec for 8 kbps PCH
•250 msg/sec for 24 kbps PCH
Actual
me value new value
Trigger 2 sec 0 sec *
utAveWin 3 sec 2 sec
roughputTimetoTrigger 5 sec 1 sec
roughputAveWin 3 sec
128 bytes 2 sec
Low 256 bytes
mer 2 sec 1 sec
kDCH8 5 sec 2 sec
kDCH16 5 sec 2 sec
kDCH32 5 sec 2 sec
ed. This may cause reconfiguration process failures and PS RABs drops.
Capacity Issues,
establishment of new Connection/bearer
PA and R99 users
band Power) and controlled part of UL noise increase too much
on) and PDE (Power Decrease Estimation) algorithms, in turn causes power spiking in the uplink spectrum.
argetBTS is BTS scheduling target for HSUPA. It is suggested to configure this parameter to be greater than PrxTarget + PrxOffset because th
•NRT PS R99 packet scheduling should be done with target lower than PrxMaxTargetBTS in order to provide capacity for HSUPA users
•PrxNoise autotuning should be limited
quires WCEL level check of minimum PrxNoise
CH_ACK_PREAMBLES
RACH_ACK_PREAMBLES
nd 24 kbps
ts & 10 ms TTI
uire activation of second SCCPCH channel
nd power capacity
when HSUPA 2 ms TTI is enabled with 24 kbps PCH
CH uses a larger section of the code tree)
ty, its good time to start thinking about actions to reduce paging channel load to avoid degradation in paging success rate.
ons with the cell]
d. This can be adjusted between PrxTargetPSMax and PrxTargetPSMin.
xTarget + PrxOffset because the Node B is more responsive than the RNC.
1.Four Triggering Events: Radio Bearer Setup, Inactivity in Cell-DCH, State Transition to Cell-DCH, Mobility.
2.Four Target Layer Selection Criterion: Freq Layer Preference (based on UE capability, Requested Service, Speed etc), Band
3.IFHO Execution: Blind HO (W/o Comp Mode)- (RB Setup Triggered & Transition to DCH state Triggered);
Measurement Based HO(With CM) -( Inactivity Timer Triggered & Mobility Triggered).
Trigger Events:
Optimization Strategy:
Confirmation to the recommended parameter set in most cases. Some market/Cluster/Site specific adjustments needed in ord
2. Preferred Frequency Layer Identifiers: (Parameters used to create/define the preferred network layer for each UE capabilit
Example: RNC-1 / PFLIdentifier-1
· LaySelWeightLoad=50
· LaySelWeightRSCP=0
· LaySelWeightPrefLayer= 100
· LaySelWeightBand= 0
· LowLoadPreference = 1
· PreflayerHSDPAxxx=F4
· PrefayerR’99xxx=F3
· PrefayerDCHSCxxx=F1, F2
· PreferBandForLayering=F1,
3. RSCP thresholds used to make upper or lower frequency bands appear more attractive:
BlindHORSCPThrAbove ; BlindHORSCPThrBelow.
NO
Any
alarms YES High Access Failure Rate
in 1
problem
period
NO
YES
Check SDCCH capacity
YES
Check if Dynamic SDCCH Allocation
High SDCCH feature is enabled
Is cell YES Blocking?
barred? Check if FACCH Call Set Up feature is
enabled
NO NO
Check TCH capacity
YES
Wrong YES YES Check and modify HR parameters
LAC, CI in High TCH
MSC? Blocking?
Check and modify HO/ADJ parameters
to offload traffic to neighbor cells
NO
DMAX YES
=0 Modify the parameters accordingly
Escalate to NSN
technical
support
NO
NO
NO
Check the site alarms
(e.g. transmission) of
Check HO Adj report to target and source.
find problematic
relationship
NO
NO NO
Neighbor
optimization (e.g.
HO margin, tilting)
Both transmitters transmit on the same frequency, but the transmission of secondary transmitter is randomly delayed to decre
Intelligent downlink diversity (IDD) doesn’t need to be enabled from BSC. It requires re-commissioning of the BTS. During the
From network side only the master TRX will be seen, the auxiliary TRX will not be seen by BSC.
Regarding 4UD activation, The 4UD (as well as the IDD) is activated using the BTS manager software during the BTS commiss
The 4UD can only be switched on if the IDD option has been switched on earlier, so 4UD cannot be used without IDD.
For activating the 4UD feature, in the BSC, the Rx DIV parameter needs to be set to Yes (Y) in order to be able to activate 4UD.
SHO overhead RT = 130-199
SHO overhead NRT = 30-45
Poor RAB drop for PS, HSDPA and HSUPA observed for Node B's on ATM
Poor RAB drop rate observed for some sites working on ATM and when the BTS commissioning for these sites were audited it w
For signaling and RT services-- the bit rate should be "CBR" (constant bit rate) and for NRT services-- it has to be "UBR+" (u
Initially poor performing sites were identified and rectified accordingly and then all ATM sites were audited for commis
100% HS AFR
The software version was not compatiable with 4 way UL Rx Diversity enabled due to the software glitch, temporary solution u
Until new version comes:
WCEL - “HSUPA2msTTIenabled” – changed from “Enabled(1)” to Disabled “0”
WCEL - “MaxTotalUplinkSymbolRate” – Changed from 3(5760kbps) to 2(3840 kbps)
Cell to cell HO statistics, PRACH delay distance and Ec/No quality distribution statistics
ffic, some HW faults ( could be found only during the site visits) causing call drops e.g. bad feeder or antenna or MHA problem?
CH, Mobility.
sted Service, Speed etc), Band Preference, Better Coverage, Traffic/Load Balancing.
Triggered);
y Triggered).
Layer Priority:
ecific adjustments needed in order to meet performance KPI and balance traffic between PCS and AWS bands or between multiple carriers
work layer for each UE capability / service type combination) Up to 8 preferred frequencies can be listed for each 16 capability & service c
2.8.2.2.2. Drop Call Analysis (TCH)
Any alarms
YES High Drop Call Rate
re Rate in problem
period 1
NO
f sector is overshooting Check the severity
of the alarm
NO Is drop
f there’s UL interference due to
HO?
BTS parameters -
mberRetransmission (RET) and Check the fault
YES
lotsSpreadTrans (SLO) situation
Is drop
due to YES 2
HO?
if combined configuration is used
BTS parameters - NO
ocksForAccessGrant (AG), Set
o make AGCH have higher YES YES
Is the link Is DL
y than PCH balanced? worse?
SDCCH capacity NO
f Dynamic SDCCH Allocation
e is enabled Check receiver path incl
NO receiver, cables, MHA,
f FACCH Call Set Up feature is
d connectors.
Is UL/DL
having bad YES Check Rx-level
TCH capacity quality? distribution report
NO
NO
Escalate to
YES NSN
.
Is drop due to TC technical
or others? support
· IDD, MHA
IDD combined with MHA gives also good results but if the cell is highly unbalanced (UL limited) it could no
So this configuration is recommended if the cell is 3-5 dB UL limited.
· IDD, 4UD
IDD improves DL more compared to 4UD on UL. This configuration is recommended if the cell is 1-3 dB UL
Expected Results:
Drive test
– Bigger coverage area (2-3 dB more in rural, better indoor, better overlapping in HO)
– Better average RxQual (25 % better)
– Less HO attempts (25 % less) and Cell re-selections (24 % less)
– Better (E)GPRS data rate
• OSS data
– More traffic (31%)
– Better DCR (0.26%)
– Less HO attempts (~23%)
re fed to separate antennas.
d to change phasing between adjacent burst, which decreases correlation between the main and auxiliary transmitter.
tter is randomly delayed to decrease correlation between the main and secondary transmitters. Phase hopping could increase interference
missioning of the BTS. During the commissioning with BTS manager software the IDD option needs to be switched on.
everal combining techniques (Interference Rejection Combining (IRC), Maximum Ratio Combining (MRC), to get a unique combined sign
haves like a normal Maximum Ratio Combiner allowing traffic to flow without requiring noise reduction.
ce Post Detection Maximum Ratio.
ftware during the BTS commissioning. During the commissioning the 4UD feature needs to be switched on.
ot be used without IDD.
te decision.
BCCH BSIC of the GSM sites can be increased
he value for this parameter was changed from 6 to 12 value
na or MHA problem?
e basically consists of following three operations:
IFHO types:
Check transmitter
path including
transmitter.
path incl
MHA,
Check idle UL
interference
In-band interference?
Check frequency plan
External interference?
Spectrum Analyzer
Check Receiver
Check TRX
.
sis Process
f both DL and UL are balanced.
nbalanced (UL limited) it could not compensate DL totally (cell will be still UL limited).
mmended if the cell is 1-3 dB UL limited (the gain of 4UD is less in rulal).
switched on.
Core PCS
FMCI Parameter RT NRT
DL DPCH Tx Power threshold for AMR (db) -1
DL DPCH Tx Power threshold for CS (db) -3
DL DPCH Tx Power threshold for NRT PS (db) -1
DL DPCH Tx Power threshold for RT PS (db) -3
IFHO cause by CPICH EcNo 1- Enabled
IFHO cause by CPICH RSCP 1- Enabled
IFHO cause by DL DPCH TX Power 0- Disabled
IFHO cause by UE TX Power 0- Disabled 0- Disabled
IFHO cause by UL DCH Quality 0- Disabled
IMSI Based IFHO 0- Not Allowed
Maximum Measurement Period (MeasRep) 6
MBLB due to Mobility EcNo offset (db) 2
MBLB due to Mobility RAB Combinations 0- All
Maximum Averaging Window (MeasRep) 6
Measurement reporting Interval 2- 0.5s
Maximum Interval between Hos (s) 10
Maximum Interval between Repetitive IF SLHOs (s) 30
Minimum measurement Interval (s) 2
Name
Neighbour cell Search Period (MeasRep) 0
UE TX Power Filter Coefficient 8- Approx. 10ms
UE Tx Power threshold for AMR (db) -3
UE Tx Power threshold for CS (db) -3
UE Tx Power threshold for NRT PS (db) -1
UE Tx Power threshold for RT PS (db) -3
UE Tx Power Time Hysteresis 13- 1280ms
Core PCS Boundary Core
HSDPA HSDPA Multi RT NRT HSDPA HSDPA Multi RT
0- Feature not 0- Feature not 0- Feature not 2 2 0- Feature not U0- Feature not
12- 640ms
1.5 3 3 3 0 3 3
11- 320ms 11- 320ms 12- 640ms 11- 320ms 13- 1280ms 11- 320ms 12- 640ms
1.5 2.5 6 2.5 3 2.5 6
12- 640ms
3 0 3 2
Core
NRT HSDPA HSDPA Multi
-14
-16
13- 1280ms
-112
-115
11- 320ms
2- 0.5s
12- 640ms
4
11- 320ms
2
Parameter Value
DCellHSDPAEnabled Enabled
HSDPA64QAMallowed Enabled
MaxTotalUplinkSymbolRate 5760
HSPDSCHCodeSet 54560
HSUPA2MSTTIEnabled Enabled
DLmaxBitRateSF16 1080 kbps
AMRLCRelatTXWindowRate7Size 512
AMRLCRelatTXWindowRate8Size 750
MaxBitRateNRTMacdflow 0
MaxNbrOfHSSCCHCodes 4 WCEL_AC
HSPDSCHMarginSF128 2 WCEL_AC
DPCHOverHSPDSCHThreshold 5 WCEL_AC
HSPA72UsersEnabled Enabled WCEL_AC
HSDPA14MbpsPerUser Enabled wbts
DCellHSDPACapaHO Disabled hc
FDPCHEnabled Disabled AC
DCellHSDPAFmcsId #NAME?
FRLCEnabled Enabled RNFC
WCEL AC AC LC LC PS PS PS
Service Affecting Non-Service Affecting
PtxMaxHSDP PtxHighHSDP
Cell DL Power MaxDLPowerCapability PtxCellMax A PtxTarget PtxOffset PtxTargetPSMax PtxTargetPSMin APwr
20W 430 430 430 425 5 420 360 425
40W 460 460 460 455 5 450 390 455
60W 478 478 478 473 5 468 408 473
30W 448 448 448 443 5 438 378 443
WCEL AC
cting
PtxPrimaryC
PICH PtxTargetHSDPA
330 420
354 450
354 468
354 438
DUMP : 6/5/2014 1:52
Yes 127
Based on license in RNC
Based on license in RNC
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Load and Service Based HO active in 6 RNCs. RNC 111 has Service Based HO only. RNC 119, RNC 121 and RNC 126 having Load Based HO.
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Yes 127
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
Related to Transport Bearer Tuning and this feature is inactive. RNC 126 and RNC 127 is using default.
TEMPLATE
1 rf 900
CLASS Parameterdefault Celcom Deviation Remarks Modificati carrier 1
WCEL AdminCellS 0 1 0 Cell lock/unlock status.
WCEL CSGroupId 0 0 1 0
WCEL CTCHCapaH 0 0 1 0
WCEL CUCEcNoTh 31 31 1 31
WCEL CUCRSCPTh -92 -92 1 -92
WCEL EVAMCapab 1 0 0 no value 0
WCEL MultiplePL 0 0 1 0
WCEL PCH24kbps 0 1 0 24 kbps paging chann 1
WCEL PRACHDela 3 3 1 3
WCEL PSGroupId 0 0 1 0
WCEL PWSMAVLi 10 10 1 10
WCEL PWSMAVLi 10 10 1 10
WCEL PWSMAVLi 37 37 1 37
WCEL PWSMAVLi 0 0 1 0
WCEL PWSMAVPw 31 31 1 31
WCEL PWSMAVPw 37 37 1 37
WCEL PWSMCell 0 0 1 0
WCEL PWSMEXPw 37 37 1 37
WCEL PWSMEXUsr 5 5 1 5
WCEL PWSMSDLi 5 5 1 5
WCEL PWSMSDLi 10 10 1 10
WCEL PWSMSDLi 5 5 1 5
WCEL PWSMSDLi 10 10 1 10
WCEL PWSMSDLi 5 5 1 5
WCEL PWSMSDPw 34 34 1 34
WCEL PWSMSDPw 37 37 1 37
WCEL PWSMSDPw 34 34 1 34
WCEL PWSMShut 0 0 1 0
WCEL PWSMShut 0 0 1 0
WCEL PowerSave 0 0 1 0
WCEL PtxPrimar 330 354 0 cell specif Yes Refer to worksheet " summary
WCEL RACHCapac 2 2 1 2
WCEL RNARGroup 0 0 1 0
WCEL RRCconnRe 6 6 1 6
WCEL RRCconnRe 5 5 1 5
WCEL RelocComm 0 0 1 0
WCEL SACB 0 0 1 0
WCEL ShutdownS 10 10 1 10
WCEL Shutdown 15 15 1 15
WCEL ToAWE_CC 10 10 1 10
WCEL ToAWS_CC 25 25 1 25
WCEL UTRAN_DRX 5 5 1 5
WCEL WCELCSCN 65535 1 0 ok 1
WCEL WCELPSCN 65535 2 0 ok 2
WCEL WCelState 0 0 1 0
WCEL NumofEag 1 1 1 1
WCEL NumofErgH 1 1 1 1
WCEL cellLevel 0 0 1 0
WCEL_AC AMROverS 90 90 1 90
WCEL_AC AMROverTr 9 9 1 9
WCEL_AC AMROverT -10 -10 1 -10
WCEL_AC AMROverT 0 0 1 0
WCEL_AC AMROverTx 20 20 1 20
WCEL_AC AMRSF -2 -2 1 -2
WCEL_AC AMRTarget 70 70 1 70
WCEL_AC AMRTarget 8 8 1 8
WCEL_AC AMRTarget -20 -20 1 -20
WCEL_AC AMRTarget -10 -10 1 -10
WCEL_AC AMRTarget 0 0 1 0
WCEL_AC AMRUnder 50 50 1 50
WCEL_AC AMRUnderT 2 2 1 2
WCEL_AC AMRUnder -100 -100 1 -100
WCEL_AC AMRUnder -100 -100 1 -100
WCEL_AC AMRUnderT -100 -100 1 -100
WCEL_AC AdminPICS 1 1 1 1
WCEL_AC AssignedPI 0 0 1 0
WCEL_AC CCHSetupE 0 1 0 Common channel setu 1
WCEL_AC CIRForFDP -44 -44 1 -44
WCEL_AC CPICHEcN -16 -16 1 -16
WCEL_AC CPICHRSC -92 -92 1 -92
WCEL_AC CPICHtoRef 20 -40 0 Celcom defYes -40
WCEL_AC CSAMRMod 0 7 0 ok 7
WCEL_AC CSAMRMo 0 1 0 ok 1
WCEL_AC CableLoss 30 30 1 30
WCEL_AC CodeTreeO 3600 3600 1 3600
WCEL_AC CodeTreeOp 1 1 1 1
WCEL_AC CodeTreeU 40 40 1 40
WCEL_AC DPCHOverH 5 5 1 5
WCEL_AC DRRCprxMa 0 0 1 0
WCEL_AC DRRCprxOf -10 -10 1 -10
WCEL_AC DRRCptxMa -5 -5 1 -5
WCEL_AC DRRCptxOf -30 -30 1 -30
WCEL_AC EVAMInUs 0 0 1 0
WCEL_AC EvamDInit 0 0 1 0
WCEL_AC EvamNumPh 8 0 0 no value 0
WCEL_AC EvamTKee 4320 0 0 no value 0
WCEL_AC EvamTSwe 216 0 0 no value 0
WCEL_AC FDPCHCode 6 6 1 6
WCEL_AC FDPCHEnab 0 0 1 0
WCEL_AC FDPCHSetu 0 0 1 0
WCEL_AC HSDPA64Q 0 1 0 HSDPA 64 QAM featur 1
WCEL_AC HSDPA64Us 0 1 0 HSDPA 64 users featu 1
WCEL_AC HSDPAenab 0 1 0 enabled 1
WCEL_AC HSFACHEna 0 0 1 0
WCEL_AC HSFACHRel 458124 0 0 no value. Related to H 0
WCEL_AC HSPA72User 0 1 0 HSPA 72 users license 1
WCEL_AC HSPDSCHC 32 54560 0 ok 54560
WCEL_AC HSPDSCHMa 8 8 1 8
WCEL_AC HSUPA16Q 0 0 1 0
WCEL_AC HSUPA2MST 0 1 0 HSUPA 2ms TTI featur 1
WCEL_AC HSUPAUser 2 0 0 no value. Related to 0
WCEL_AC MHA 0 0 1 0
WCEL_AC MaxBitRat 384 384 1 384
WCEL_AC MaxBitRat 384 384 1 384
WCEL_AC MaxCodeRe 40 40 1 40
WCEL_AC MaxNbrOf 1 4 0 4 HS SCCH Yes 4
WCEL_AC PICState 1 1 1 1
WCEL_AC PrxLoadMa 20 40 0 ok 40
WCEL_AC PrxLoadMa 0 0 1 0
WCEL_AC PrxOffset 8 0 0 no value 0
WCEL_AC PtxCellMax 430 460 0 depends onYes Refer to worksheet " summary
WCEL_AC PtxDLabsM 370 370 1 370
WCEL_AC PtxFDPCH 90 90 1 90
WCEL_AC PtxFDPCH 200 200 1 200
WCEL_AC PtxMaxHS 430 460 0 depends onYes Refer to worksheet " summary
WCEL_AC PtxOffset 20 20 1 20
WCEL_AC PtxOffset 12 12 1 12
WCEL_AC PtxOffset 6 6 1 6
WCEL_AC PtxOffset 8 10 0 ok 10
WCEL_AC PtxOffset 8 0 0 no value 0
WCEL_AC PtxPSstre 370 370 1 370
WCEL_AC PtxTarget 385 450 0 depends on power settRefer to worksheet " summary
WCEL_AC PtxTargetT 32767 32767 1 32767
WCEL_AC PtxTargetT 32767 32767 1 32767
WCEL_AC RefServFo 0 0 1 0
WCEL_AC RxDivIndic 1 1 1 1
WCEL_AC SIRDPCCHO 0 0 1 0
WCEL_AC SRBBitRat 66559 508927 0 ok 508927
WCEL_AC SRBMapRR 457728 310272 0 ok 310272
WCEL_AC TPCComma 4 4 1 4
WCEL_AC UEtxPowe 24 24 1 24
WCEL_AC UEtxPowe 21 21 1 21
WCEL_AC UEtxPowe 21 21 1 21
WCEL_AC UsersPerH 30 0 0 no value 0
WCEL_HC BlindHOEc -24 0 0 ok, RACH EYes 0
WCEL_HC BlindHORS -95 -25 0 ok Yes -25
WCEL_HC CellWeight 100 100 1 100
WCEL_HC DCellHSDP 0 0 1 0
WCEL_HC DLLoadSta 4 4 1 4
WCEL_HC HSDPAFmcgIdentifier
WCEL_HC HSDPAFmciIdentifier
WCEL_HC HSDPAFmcsIdentifier
WCEL_HC HSPAFmcsIdentifier
WCEL_HC DirectedR 1 0 0 not enabled as MBLB i 0
WCEL_HC DirectedR 0 1 0 Enabled for HSDPA 1
WCEL_HC HHoMaxAll 32 64 0 ok Yes 64
WCEL_HC HHoMaxAll 32 64 0 ok Yes 64
WCEL_HC HSCapabil 3 3 1 3
WCEL_HC HSCapabili 5 0 0 ok Yes 0
WCEL_HC HSDPALaye 0 1 0 enabled. Yes 1
WCEL_HC HSLoadSta 32 32 1 32
WCEL_HC HSLoadSta 127 127 1 127
WCEL_HC HSLoadSta 24 24 1 24
WCEL_HC HSLoadSta 127 127 1 127
WCEL_HC HSLoadSta 2 2 1 2
WCEL_HC HSPACapa 0 0 1 0
WCEL_HC IncomingL 0 1 0 ok, based Yes 1
WCEL_HC LHOCapaRe 70 70 1 70
WCEL_HC LHOCapaRe 70 70 1 70
WCEL_HC LHODelayO 30 30 1 30
WCEL_HC LHODelayO 30 30 1 30
WCEL_HC LHODelayO 30 30 1 30
WCEL_HC LHODelayO 30 30 1 30
WCEL_HC LHOHardBl 10 10 1 10
WCEL_HC LHOHardBl 50 50 1 50
WCEL_HC LHOHystTi 2 2 1 2
WCEL_HC LHOHystTi 2 2 1 2
WCEL_HC LHOHystTim 2 2 1 2
WCEL_HC LHOHystTi 2 2 1 2
WCEL_HC LHONRTTra 10 10 1 10
WCEL_HC LHONumbUE 0 0 1 0
WCEL_HC LHONumbU 0 0 1 0
WCEL_HC LHOPwrOff -15 -15 1 -15
WCEL_HC LHOPwrOff -7 -7 1 -7
WCEL_HC LHOResRat 80 80 1 80
WCEL_HC LHOWinSiz 5 5 1 5
WCEL_HC LHOWinSiz 5 5 1 5
WCEL_HC LHOWinSiz 5 5 1 5
WCEL_HC LHOWinSiz 5 5 1 5
WCEL_HC LHOWinSiz 0 0 1 0
WCEL_HC LHOWinSiz 0 0 1 0
WCEL_HC LHOWinSiz 0 0 1 0
WCEL_HC LHOWinSiz 0 0 1 0
WCEL_HC LoadBased -25 -25 1 -25
WCEL_HC LoadBased 0 0 1 0
WCEL_HC MBLBInacti 0 0 1 0
WCEL_HC MBLBMobil 0 0 1 0
WCEL_HC MBLBRABSe 0 1 0 MBLB enabl
Yes 0
WCEL_HC MBLBRABSe 1 1 1 1
WCEL_HC MBLBState 0 1 0 MBLB enabl
Yes 0
WCEL_HC MIMOHSDP 0 0 1 0
WCEL_HC MaxNumbe 6 6 1 6
WCEL_HC NrtFmcgIdentifier
WCEL_HC NrtFmciIdentifier
WCEL_HC NrtFmcsIdentifier
WCEL_HC PFLIdentifier
WCEL_HC RTWithHSDPAFmcgIdentifier 1
WCEL_HC RTWithHSDPAFmciIdentifier
WCEL_HC RTWithHSDPAFmcsIdentifier
WCEL_HC RTWithHSPAFmcsIdentifier
WCEL_HC RtFmcgIdentifier
WCEL_HC RtFmciIdentifier
WCEL_HC RtFmcsIdentifier
WCEL_HC ServHONum 1 2 0 Service and Load Bas 2
WCEL_HC ServHONum 1 1 1 1
WCEL_HC ServHOPeri 0 0 1 0
WCEL_HC ServHOPer 0 0 1 0
WCEL_LC MaxIncrInt 10 10 1 10
WCEL_LC NonHSEve 1 0 0 no value 0
WCEL_LC PrxMeasFil 2 2 1 2
WCEL_LC PrxNoise -1050 -1050 1 -1050
WCEL_LC PrxNoiseAu 1 1 1 1
WCEL_LC PrxOffset 10 10 1 10
WCEL_LC PrxTarget 40 80 0 ok Yes 80
WCEL_LC PrxTarget 65535 65535 1 65535
WCEL_LC PrxTotalRe 80 0 0 no value 0
WCEL_LC PtxMeasFil 2 2 1 2
WCEL_LC PtxOffset 10 5 0 ok Yes 5
WCEL_LC PtxTarget 400 455 0 depends on power settRefer to worksheet " summary
WCEL_LC PtxTotalRe 80 0 0 no value 0
WCEL_LC RACHloadR 80 0 0 no value 0
WCEL_LC RACHmeasFi 10 10 1 10
WCEL_LC RSEPSEve 1 0 0 no value 0
WCEL_LC RTWPEven 20 0 0 no value 0
WCEL_LC RTWPEven 1 0 0 no value 0
WCEL_LC RTWPMeasF 2 0 0 no value 0
WCEL_LC TCPEventE 20 0 0 no value 0
WCEL_LC TCPEvent 1 0 0 no value 0
WCEL_LC TCPMeasFil 2 0 0 no value 0
WCEL_LC VoiceOver 1 1 1 1
WCEL_PC DPCModeC 1 1 1 1
WCEL_PC PRACHRequ -25 -20 0 ok -20
WCEL_PC PTxPICH -8 -8 1 -8
WCEL_PC PowerOffs 2 -3 0 ok -3
WCEL_PC PO1_15 8 8 1 8
WCEL_PC PO1_30 12 12 1 12
WCEL_PC PO1_60 16 16 1 16
WCEL_PC PowerRam 2 3 0 ok 3
WCEL_PC PtxAICH -8 -3 0 ok -3
WCEL_PC PtxBCCHH 70 0 0 no value 0
WCEL_PC PtxBCCHH -20 0 0 no value 0
WCEL_PC PtxMaxEHI 84 84 1 84
WCEL_PC PtxOffset 108 108 1 108
WCEL_PC PtxOffset 128 128 1 128
WCEL_PC PtxOffset 128 128 1 128
WCEL_PC PtxOffset 84 84 1 84
WCEL_PC PtxOffset 128 128 1 128
WCEL_PC PtxOffset 140 0 0 no value 0
WCEL_PC PtxPrimar -50 -50 1 -50
WCEL_PC PtxPrimar -30 -30 1 -30
WCEL_PC PtxSCCPCH 0 0 1 0
WCEL_PC PtxSCCPCH -50 0 0 ok 0
WCEL_PC PtxSCCPCH -20 0 0 ok 0
WCEL_PC PtxSCCPCH -20 -20 1 -20
WCEL_PC PtxSecSCH -30 -30 1 -30
WCEL_PC RsrvdSigna 10 10 1 10
WCEL_PS AltScramb 0 0 1 0
WCEL_PS CPCEnable 0 0 1 0
WCEL_PS DCellAnd 0 0 1 0
WCEL_PS DCellHSDP 0 1 0 enabled feature 1
WCEL_PS DeltaPrxM 4 10 0 ok 10
WCEL_PS DeltaPrxM 6 6 1 6
WCEL_PS DeltaPtxM 4 4 1 4
WCEL_PS DeltaPtxM 6 15 0 ok 15
WCEL_PS EDCHMinSe 29 29 1 29
WCEL_PS EDCHMinim 4 4 1 4
WCEL_PS FachLoadM 5 5 1 5
WCEL_PS FachLoadT 75 75 1 75
WCEL_PS HSDPAMP 12 0 0 no value 0
WCEL_PS HSDPAMaxB 6 6 1 6
WCEL_PS HSFACHAct 0 0 1 0
WCEL_PS HSFACHAct 1 0 0 no value 0
WCEL_PS HSFACHActi 16 0 0 no value 0
WCEL_PS HSFACHRLC 0 0 1 0
WCEL_PS HSFACHVol 512 0 0 no value 0
WCEL_PS HSPAQoSEn 0 2 0 ok 2
WCEL_PS HSUPAEnab 0 1 0 enabled 1
WCEL_PS HspaMulti 0 1 0 enabled 1
WCEL_PS InitialBitR 64 64 1 64
WCEL_PS InitialBitR 64 64 1 64
WCEL_PS MIMOEnab 0 0 1 0
WCEL_PS MIMOWith 0 0 1 0
WCEL_PS MaxNumbH 0 0 1 0
WCEL_PS MaxNumbH 0 0 1 0
WCEL_PS MaxNumbe 0 72 0 ok 72
WCEL_PS MaxNumbe 0 0 1 0
WCEL_PS MaxNumbe 0 0 1 0
WCEL_PS MaxNumb 16 16 1 16
WCEL_PS MaxNumbe 10 10 1 10
WCEL_PS MaxNumbe 5 5 1 5
WCEL_PS MaxTotalU 0 3 0 ok, for 5. Yes 3
WCEL_PS MinAllowe 8 64 0 ok Yes 64
WCEL_PS MinAllowe 8 64 0 ok yes 64
WCEL_PS NASsignVo 8 8 1 8
WCEL_PS NASsignVo 8 8 1 8
WCEL_PS NumberEDC 2 2 1 2
WCEL_PS OCULNRTDC 10 10 1 10
WCEL_PS OCdlNrtDC 60 60 1 60
WCEL_PS PBSgrante 20 20 1 20
WCEL_PS PBSgrante 30 30 1 30
WCEL_PS PBSgrante 15 15 1 15
WCEL_PS PrxLoadMa 20 20 1 20
WCEL_PS PrxMaxOri 80 80 1 80
WCEL_PS PrxMaxTar 60 100 0 ok, in shr1Yes 100
WCEL_PS PrxTarget 40 80 0 ok Yes 80
WCEL_PS PrxTarget 40 80 0 ok Yes 80
WCEL_PS PrxTarget 5 5 1 5
WCEL_PS PrxTarget 5 5 1 5
WCEL_PS PtxHighHS 410 455 0 depends onYes Refer to worksheet " summary
WCEL_PS PtxMargin 5 5 1 5
WCEL_PS PtxTargetP 5 10 0 ok Yes 10
WCEL_PS PtxTarget 400 450 0 depends onYes Refer to worksheet " summary
WCEL_PS PtxTargetP 360 390 0 depends onYes Refer to worksheet " summary
WCEL_PS PtxTarget 10 10 1 10
WCEL_PS PtxTarget 10 10 1 10
WCEL_PS PtxThresh -10 -10 1 -10
WCEL_PS RachLoadM 5 5 1 5
WCEL_PS RachLoadT 75 75 1 75
WCEL_PS TargetNSE 30 50 0 ok Yes 50
WCEL_PS TrafVolThr 128 512 0 ok Yes 512
WCEL_PS ULLoadSta 8 8 1 8
WCEL_PS ULLoadSta -5 127 0 ok Yes 127
WCEL_SIB ACBarredLi 0 0 1 0
WCEL_SIB AICHTraTi 0 0 1 0
WCEL_SIB AbsPrioCel 0 0 1 0
WCEL_SIB AllowedPre 15 15 1 15
WCEL_SIB AllowedRA 4095 4095 1 4095
WCEL_SIB CellBarred 1 1 1 1
WCEL_SIB CellSelQua 0 0 1 0
WCEL_SIB Cell_Reser 1 1 1 1
WCEL_SIB HCS_PRIO 0 0 1 0
WCEL_SIB InterFreqSc 4 4 1 4
WCEL_SIB InterRATSc 4 4 1 4
WCEL_SIB IntraFreq_ 0 0 1 0
WCEL_SIB KforCTCH 0 0 1 0
WCEL_SIB LTECellRes 0 1 0 ok, based Yes 1
WCEL_SIB N300 3 2 0 ok Yes 2
WCEL_SIB N312 2 2 1 2
WCEL_SIB N312Conn 2 2 1 2
WCEL_SIB N313 4 4 1 4
WCEL_SIB N315 0 0 1 0
WCEL_SIB NCr 8 8 1 8
WCEL_SIB NbrOfSCCP 1 2 0 ok Yes 2
WCEL_SIB NforCTCH 2 2 1 2
WCEL_SIB NonHCSNc 8 8 1 8
WCEL_SIB NonHCSTc 0 0 1 0
WCEL_SIB NonHCSTcr 0 0 1 0
WCEL_SIB PI_amount 2 2 1 2
WCEL_SIB PRACHScra 0 0 1 0
WCEL_SIB PRACH_pre 8 8 1 8
WCEL_SIB QHCS 0 0 1 0
WCEL_SIB Qhyst1 0 0 1 0
WCEL_SIB Qhyst1FAC 0 0 1 0
WCEL_SIB Qhyst1PCH 0 0 1 0
WCEL_SIB Qhyst2 1 1 1 1
WCEL_SIB Qhyst2FAC 2 2 1 2
WCEL_SIB Qhyst2PCH 2 2 1 2
WCEL_SIB QqualMin -18 -18 1 -18
WCEL_SIB QrxlevMin -58 -58 1 -58
WCEL_SIB RACHInter 1 0 0 ok, for MBLYes 1
WCEL_SIB RACHIntra 0 1 0 ok, for MBLYes 0
WCEL_SIB RACH_Tx_ 50 50 1 50
WCEL_SIB RACH_Tx_ 0 20 0 ok Yes 20
WCEL_SIB RACH_tx_ 8 4 0 ok Yes 4
WCEL_SIB SHCS_RAT -1 -1 1 -1
WCEL_SIB SHCS_RAT -1 -1 1 -1
WCEL_SIB SIB4Indica 0 1 0 ok Yes 1
WCEL_SIB SIB7factor 0 0 1 0
WCEL_SIB Sintersear 4 3 0 ok for U210Yes 7
WCEL_SIB Sintersear 4 3 0 ok for U210Yes 7
WCEL_SIB Sintrasear 5 5 1 5
WCEL_SIB Sintrasear 5 5 1 5
WCEL_SIB Slimit_Sea 1 1 1 1
WCEL_SIB Slimit_Se 1 1 1 1
WCEL_SIB SpeedScale 7 7 1 7
WCEL_SIB Sprioritys 0 3 0 ok Yes 3
WCEL_SIB Sprioritys 0 2 0 ok Yes 2
WCEL_SIB SsearchHC -1 -1 1 -1
WCEL_SIB SsearchHC -1 -1 1 -1
WCEL_SIB Ssearch_R 2 1 0 ok Yes 1
WCEL_SIB Ssearch_R 2 1 0 ok Yes 1
WCEL_SIB T300 10 10 1 10
WCEL_SIB T312 6 6 1 6
WCEL_SIB T312Conn 1 6 0 ok Yes 6
WCEL_SIB T313 3 2 0 ok Yes 2
WCEL_SIB T315 4 2 0 ok Yes 2
WCEL_SIB TBarred 2 2 1 2
WCEL_SIB TCrmax 2 2 1 2
WCEL_SIB TCrmaxHys 0 0 1 0
WCEL_SIB Threshserv 0 1 0 ok, it is a Yes 1
WCEL_SIB Treselectio 2 2 1 2
WCEL_SIB Treselecti 10 10 1 10
WCEL_SIB Treselecti 2 2 1 2
WCEL_SIB UseOfHCS 0 0 1 0
RNC 126 having Load Based HO.
TEMPLATE
0 0 0 0 0 0
0 0 0 0 0 0
31 31 31 31 31 31
-92 -92 -92 -92 -92 -92
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 1 1 1
3 3 3 3 3 3
0 0 0 0 0 0
10 10 10 10 10 10
10 10 10 10 10 10
37 37 37 37 37 37
0 0 0 0 0 0
31 31 31 31 31 31
37 37 37 37 37 37
0 0 0 0 0 0
37 37 37 37 37 37
5 5 5 5 5 5
5 5 5 5 5 5
10 10 10 10 10 10
5 5 5 5 5 5
10 10 10 10 10 10
5 5 5 5 5 5
34 34 34 34 34 34
37 37 37 37 37 37
34 34 34 34 34 34
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Refer to worksheet " summary configuration" 330 354 354 354
2 2 2 2 2 2
0 0 0 0 0 0
6 6 6 6 6 6
5 5 5 5 5 5
0 0 0 0 0 0
0 0 0 0 0 0
10 10 10 10 10 10
15 15 15 15 15 15
10 10 10 10 10 10
25 25 25 25 25 25
5 5 5 5 5 5
1 1 1 1 1 1
2 2 2 2 2 2
0 0 0 0 0 0
1 1 1 1 1 1
1 1 1 1 1 1
0 0 0 0 0 0
90 90 90 90 90 90
9 9 9 9 9 9
-10 -10 -10 -10 -10 -10
0 0 0 0 0 0
20 20 20 20 20 20
-2 -2 -2 -2 -2 -2
70 70 70 70 70 70
8 8 8 8 8 8
-20 -20 -20 -20 -20 -20
-10 -10 -10 -10 -10 -10
0 0 0 0 0 0
50 50 50 50 50 50
2 2 2 2 2 2
-100 -100 -100 -100 -100 -100
-100 -100 -100 -100 -100 -100
-100 -100 -100 -100 -100 -100
1 1 1 1 1 1
0 0 0 0 0 0
1 1 1 1 1 1
-44 -44 -44 -44 -44 -44
-16 -16 -16 -16 -16 -16
-92 -92 -92 -92 -92 -92
-40 -40 -40 -40 -40 -40
7 7 7 7 7 7
1 1 1 1 1 1
30 30 30 30 30 30
3600 3600 3600 3600 3600 3600
1 1 1 1 1 1
40 40 40 40 40 40
5 5 5 5 5 5
0 0 0 0 0 0
-10 -10 -10 -10 -10 -10
-5 -5 -5 -5 -5 -5
-30 -30 -30 -30 -30 -30
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
6 6 6 6 6 6
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 1 1 1
1 1 1 1 1 1
1 1 1 1 1 1
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 1 1 1
54560 54560 54560 54560 54560 54560
8 8 8 8 8 8
0 0 0 0 0 0
1 1 1 1 1 1
0 0 0 0 0 0
0 0 0 0 0 0
384 384 384 384 384 384
384 384 384 384 384 384
40 40 40 40 40 40
4 4 4 4 4 4
1 1 1 1 1 1
40 40 40 40 40 40
0 0 0 0 0 0
0 0 0 0 0 0
Refer to worksheet " summary configuration" 430 478 448 460
370 370 370 370 370 370
90 90 90 90 90 90
200 200 200 200 200 200
Refer to worksheet " summary configuration" 430 478 448 460
20 20 20 20 20 20
12 12 12 12 12 12
6 6 6 6 6 6
10 10 10 10 10 10
0 0 0 0 0 0
370 370 370 370 370 370
Refer to worksheet " summary configuration" 420 468 438 450
32767 32767 32767 32767 32767 32767
32767 32767 32767 32767 32767 32767
0 0 0 0 0 0
1 1 1 1 1 1
0 0 0 0 0 0
508927 508927 508927 508927 508927 508927
310272 310272 310272 310272 310272 310272
4 4 4 4 4 4
24 24 24 24 24 24
21 21 21 21 21 21
21 21 21 21 21 21
0 0 0 0 0 0
0 0 0 0 0 0
-25 -25 -25 -25 -25 -25
100 100 100 100 100 100
0 0 0 0 0 0
4 4 4 4 4 4
0 0 0 0 0 0
1 1 1 1 1 1
64 64 64 64 64 64
64 64 64 64 64 64
3 3 3 3 3 3
0 0 0 0 0 0
1 1 1 1 1 1
32 32 32 32 32 32
127 127 127 127 127 127
24 24 24 24 24 24
127 127 127 127 127 127
2 2 2 2 2 2
0 0 0 0 0 0
1 1 1 1 1 1
70 70 70 70 70 70
70 70 70 70 70 70
30 30 30 30 30 30
30 30 30 30 30 30
30 30 30 30 30 30
30 30 30 30 30 30
10 10 10 10 10 10
50 50 50 50 50 50
2 2 2 2 2 2
2 2 2 2 2 2
2 2 2 2 2 2
2 2 2 2 2 2
10 10 10 10 10 10
0 0 0 0 0 0
0 0 0 0 0 0
-15 -15 -15 -15 -15 -15
-7 -7 -7 -7 -7 -7
80 80 80 80 80 80
5 5 5 5 5 5
5 5 5 5 5 5
5 5 5 5 5 5
5 5 5 5 5 5
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
-25 -25 -25 -25 -25 -25
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 1 1 1
0 0 0 0 0 0
0 0 0 0 0 0
6 6 6 6 6 6
2 2 2 2 2 2
1 1 1 1 1 1
0 0 0 0 0 0
0 0 0 0 0 0
10 10 10 10 10 10
0 0 0 0 0 0
2 2 2 2 2 2
-1050 -1050 -1050 -1050 -1050 -1050
1 1 1 1 1 1
10 10 10 10 10 10
80 80 80 80 80 80
65535 65535 65535 65535 65535 65535
0 0 0 0 0 0
2 2 2 2 2 2
5 5 5 5 5 5 5 5 5 5
Refer to worksheet " summary configuration" 425 473 443 455
0 0 0 0 0 0
0 0 0 0 0 0
10 10 10 10 10 10
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 1 1 1
1 1 1 1 1 1
-20 -20 -20 -20 -20 -20
-8 -8 -8 -8 -8 -8
-3 -3 -3 -3 -3 -3
8 8 8 8 8 8
12 12 12 12 12 12
16 16 16 16 16 16
3 3 3 3 3 3
-3 -3 -3 -3 -3 -3
0 0 0 0 0 0
0 0 0 0 0 0
84 84 84 84 84 84
108 108 108 108 108 108
128 128 128 128 128 128
128 128 128 128 128 128
84 84 84 84 84 84
128 128 128 128 128 128
0 0 0 0 0 0
-50 -50 -50 -50 -50 -50
-30 -30 -30 -30 -30 -30
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
-20 -20 -20 -20 -20 -20
-30 -30 -30 -30 -30 -30
10 10 10 10 10 10
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 1 1 1
10 10 10 10 10 10
6 6 6 6 6 6
4 4 4 4 4 4
15 15 15 15 15 15
29 29 29 29 29 29
4 4 4 4 4 4
5 5 5 5 5 5
75 75 75 75 75 75
0 0 0 0 0 0
6 6 6 6 6 6
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
2 2 2 2 2 2
1 1 1 1 1 1
1 1 1 1 1 1
64 64 64 64 64 64
64 64 64 64 64 64
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
72 72 72 72 72 72
0 0 0 0 0 0
0 0 0 0 0 0
16 16 16 16 16 16
10 10 10 10 10 10
5 5 5 5 5 5
3 3 3 3 3 3
64 64 64 64 64 64
64 64 64 64 64 64
8 8 8 8 8 8
8 8 8 8 8 8
2 2 2 2 2 2
10 10 10 10 10 10
60 60 60 60 60 60
20 20 20 20 20 20
30 30 30 30 30 30
15 15 15 15 15 15
20 20 20 20 20 20
80 80 80 80 80 80
100 100 100 100 100 100
80 80 80 80 80 80
80 80 80 80 80 80
5 5 5 5 5 5
5 5 5 5 5 5
Refer to worksheet " summary configuration" 425 473 443 455
5 5 5 5 5 5
10 10 10 10 10 10
Refer to worksheet " summary configuration" 420 468 438 450
Refer to worksheet " summary configuration" 360 408 378 390
10 10 10 10 10 10
10 10 10 10 10 10
-10 -10 -10 -10 -10 -10
5 5 5 5 5 5
75 75 75 75 75 75
50 50 50 50 50 50
512 512 512 512 512 512
8 8 8 8 8 8
127 127 127 127 127 127
0 0 0 0 0 0
0 0 0 0 0 0
3 3 2 3 2 2
15 15 15 15 15 15
4095 4095 4095 4095 4095 4095
1 1 1 1 1 1
0 0 0 0 0 0
1 1 1 1 1 1
0 0 0 0 0 0
4 4 4 4 4 4
4 4 4 4 4 4
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 1 1 1
2 2 2 2 2 2
2 2 2 2 2 2
2 2 2 2 2 2
4 4 4 4 4 4
0 0 0 0 0 0
8 8 8 8 8 8
2 2 2 2 2 2
2 2 2 2 2 2
8 8 8 8 8 8
0 0 0 0 0 0
0 0 0 0 0 0
2 2 2 2 2 2
0 0 0 0 0 0
8 8 8 8 8 8
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 1 1 1
2 2 2 2 2 2
2 2 2 2 2 2
-18 -18 -18 -18 -18 -18
-58 -58 -58 -58 -58 -58
1 1 1 1 1 1
0 0 0 0 0 0
50 50 50 50 50 50
20 20 20 20 20 20
4 4 4 4 4 4
-1 -1 -1 -1 -1 -1
-1 -1 -1 -1 -1 -1
1 1 1 1 1 1
0 0 0 0 0 0
3 3 3 3 3 3
3 3 3 3 3 3
5 5 5 5 5 5
5 5 5 5 5 5
1 1 1 1 1 1
1 1 1 1 1 1
7 7 7 7 7 7
3 3 3 3 3 3
2 2 2 2 2 2
-1 -1 -1 -1 -1 -1
-1 -1 -1 -1 -1 -1
1 1 1 1 1 1
1 1 1 1 1 1
10 10 10 10 10 10
6 6 6 6 6 6
6 6 6 6 6 6
2 2 2 2 2 2
2 2 2 2 2 2
2 2 2 2 2 2
2 2 2 2 2 2
0 0 0 0 0 0
1 1 1 1 1 1
2 2 2 2 2 2
10 10 10 10 10 10
2 2 2 2 2 2
0 0 0 0 0 0
LTE Interw MBLB
10762 10712 10737 U9
0 0 0 0 0
0 0 0 0 0
31 31 31 31 31
-92 -92 -92 -92 -92
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
3 3 3 3 3
0 0 0 0 0
10 10 10 10 10
10 10 10 10 10
37 37 37 37 37
0 0 0 0 0
31 31 31 31 31
37 37 37 37 37
0 0 0 0 0
37 37 37 37 37
5 5 5 5 5
5 5 5 5 5
10 10 10 10 10
5 5 5 5 5
10 10 10 10 10
5 5 5 5 5
34 34 34 34 34
37 37 37 37 37
34 34 34 34 34
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
2 2 2 2 2
0 0 0 0 0
6 6 6 6 6
5 5 5 5 5
0 0 0 0 0
0 0 0 0 0
10 10 10 10 10
15 15 15 15 15
10 10 10 10 10
25 25 25 25 25
5 5 5 5 5
1 1 1 1 1
2 2 2 2 2
0 0 0 0 0
1 1 1 1 1
1 1 1 1 1
0 0 0 0 0
90 90 90 90 90
9 9 9 9 9
-10 -10 -10 -10 -10
0 0 0 0 0
20 20 20 20 20
-2 -2 -2 -2 -2
70 70 70 70 70
8 8 8 8 8
-20 -20 -20 -20 -20
-10 -10 -10 -10 -10
0 0 0 0 0
50 50 50 50 50
2 2 2 2 2
-100 -100 -100 -100 -100
-100 -100 -100 -100 -100
-100 -100 -100 -100 -100
1 1 1 1 1
0 0 0 0 0
1 1 1 1 1
-44 -44 -44 -44 -44
-16 -16 -16 -16 -16
-92 -92 -92 -92 -92
-40 -40 -40 -40 -40
7 7 7 7 7
1 1 1 1 1
30 30 30 30 30
3600 3600 3600 3600 3600
1 1 1 1 1
40 40 40 40 40
5 5 5 5 5
0 0 0 0 0
-10 -10 -10 -10 -10
-5 -5 -5 -5 -5
-30 -30 -30 -30 -30
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
6 6 6 6 6
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
54560 54560 54560 54560 54560
8 8 8 8 8
0 0 0 0 0
1 1 1 1 1
0 0 0 0 0
0 0 0 0 0
384 384 384 384 384
384 384 384 384 384
40 40 40 40 40
4 4 4 4 4
1 1 1 1 1
40 40 40 40 40
0 0 0 0 0
0 0 0 0 0
20 20 20 20 20
12 12 12 12 12
6 6 6 6 6
10 10 10 10 10
0 0 0 0 0
370 370 370 370 370
0 0 0 0 0
0 0 0 0 0
10 10 10 10 10
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
1 1 1 1 1
-20 -20 -20 -20 -20
-8 -8 -8 -8 -8
-3 -3 -3 -3 -3
8 8 8 8 8
12 12 12 12 12
16 16 16 16 16
3 3 3 3 3
-3 -3 -3 -3 -3
0 0 0 0 0
0 0 0 0 0
84 84 84 84 84
108 108 108 108 108
128 128 128 128 128
128 128 128 128 128
84 84 84 84 84
128 128 128 128 128
0 0 0 0 0
-50 -50 -50 -50 -50
-30 -30 -30 -30 -30
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
-20 -20 -20 -20 -20
-30 -30 -30 -30 -30
10 10 10 10 10
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
10 10 10 10 10
6 6 6 6 6
4 4 4 4 4
15 15 15 15 15
29 29 29 29 29
4 4 4 4 4
5 5 5 5 5
75 75 75 75 75
0 0 0 0 0
6 6 6 6 6
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
2 2 2 2 2
1 1 1 1 1
1 1 1 1 1
64 64 64 64 64
64 64 64 64 64
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
72 72 72 72 72
0 0 0 0 0
0 0 0 0 0
16 16 16 16 16
10 10 10 10 10
5 5 5 5 5
3 3 3 3 3
64 64 64 64 64
64 64 64 64 64
8 8 8 8 8
8 8 8 8 8
2 2 2 2 2
10 10 10 10 10
60 60 60 60 60
20 20 20 20 20
30 30 30 30 30
15 15 15 15 15
20 20 20 20 20
80 80 80 80 80
100 100 100 100 100
80 80 80 80 80
80 80 80 80 80
5 5 5 5 5
5 5 5 5 5
5 5 5 5 5
10 10 10 10 10
10 10 10 10 10
10 10 10 10 10
-10 -10 -10 -10 -10
5 5 5 5 5
75 75 75 75 75
50 50 50 50 50
512 512 512 512 512
8 8 8 8 8
127 127 127 127 127
0 0 0 0 0
0 0 0 0 0
3 3 2 2 0
15 15 15 15 15
4095 4095 4095 4095 4095
1 1 1 1 1
0 0 0 0 0
1 1 1 1 1
0 0 0 0 0
4 4 4 4 4
4 4 4 4 4
0 0 0 0 0
0 0 0 0 0
1 1 1 1
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
4 4 4 4 4
0 0 0 0 0
8 8 8 8 8
2 2 2 2 2
2 2 2 2 2
8 8 8 8 8
0 0 0 0 0
0 0 0 0 0
2 2 2 2 2
0 0 0 0 0
8 8 8 8 8
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
0 0 0 0 0
1 1 1 1 1
2 2 2 2 2
2 2 2 2 2
-18 -18 -18 -18 -18
-58 -58 -58 -58 -58
1 0 0 0 0
0 1 1 1 1
50 50 50 50 50
20 20 20 20 20
4 4 4 4 4
-1 -1 -1 -1 -1
-1 -1 -1 -1 -1
1 1 1 1 1
0 0 0 0 0
3 3 3 3 7
3 3 3 3 7
5 5 5 5 5
5 5 5 5 5
1 1 1 1 1
1 1 1 1 1
7 7 7 7 7
3 3 3 3 3
2 2 2 2 2
-1 -1 -1 -1 -1
-1 -1 -1 -1 -1
1 1 1 1 1
1 1 1 1 1
10 10 10 10 10
6 6 6 6 6
6 6 6 6 6
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
2 2 2 2 2
0 0 0 0 0
1 1 1 1 1
2 2 2 2 2
10 10 10 10 10
2 2 2 2 2
0 0 0 0 0