Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
The microcontroller of the MIO10 unit handles all (protection up to 153VDC). The high sig-
timing relevant tasks of the functions that are de- nal input current is limited to 2mA (R0001)
fined by the processing parameters. and 1.2mA (R0002).
Besides this, the µC manages all communication 8 galvanic isolated digital outputs by relay
activities of the RTU560-System. All configuration NO contacts are use to switch loads up to
and processing parameters are loaded via the 8A and up to 250VDC. A release of an
RTU system bus during the initialization. output command is done by test of the
supply voltage of the relay.
Also during the initialization, the 560CID11 per-
forms several tests. If an error is detected, it is Galvanic isolated 1-of-n test interface for
reported to the central station. measurement of Relay coil resistance in
the process circuit (100 Ohm up to 10.000
The I/O functionality consists of several sub func-
Ohm). Switching between testing and
tions:
process by controllable GO- and MEAS
8 analog input channels for measurement outputs.
of current in the range of 2mA up to 40mA
Galvanic isolated supervision input for
(bipolar) und voltages from 2V up to 20V
process voltages of 24/48/60VDC
(bipolar). All channels are differential in-
(R0001) or 110V/125VDC (R0002).
puts. The selection between voltage and
current measurement and ranges is made Isolated NC relay contact to signal an
by DIP-Switches. (2 per channel). Alarm or FAIL condition to other units.
16 galvanic isolated digital inputs for cap- Battery supply supervision available at
turing of digital signals are arranged in 2 connector X6. This input can differentiate
groups of 8. All inputs are protected between several states like battery OK,
against over-voltage and reverse-voltage AC Power fail, cable broken or battery
conditions. The voltage range is 0V to low.
60VDC for R0001 (protection up to
72VDC) and 0 to 110/125 VDC for R0002
0 .. 10mA, ±10mA The analog input unit can carry out the following
0 .. 20mA, ±20mA processing functions on the measured values:
0 .. 40mA, ±40mA Zero point monitoring
0 .. 2VDC, ±2VDC Switch-over recognition
0 .. 20VDC, ±10VDC Smoothing
Other effective ranges and live zero signals be- Threshold value monitoring on absolute
come generated out of these ranges through con- value or with accumulation and periodic
version on the CMU. background transmission.
Tolerance: ±5%
Ethernet LAN Interface ‘E1’ and ‘E2’
Current min.: 0A
Physical Interface: 10BaseT/100BaseT
Bit rate: 10/100 MBit/s Current max.: 1A
Input/Output Multi- IO
AI (Analog Input) BI (Binary Input R0002)
Voltage 0-2V (+/-2V bipolar) Voltage 110 / 125VDC (+/-20%)
0-20V( +/-10V bipolar) ≥ 80V = Logic 1
Input impedance > 100kOhm ≤ 45V = Logic 0
Input current 1,2mA constant
Current Range 1 0-2mA (+/-2mA bipolar)
0-5mA (+/-5mA bipolar) Over-voltage protection Max. 152VDC
0-10mA (+/-10mA bipolar)
Reverse voltage protec- yes
Shunt-Impedance 150 Ohm tion
Current Range 2 0-20mA (+/-20mA bipolar) Max. input signal fre- 120Hz
quency Channel 1 up to 16KHz
0-40mA (+/-40mA bipolar)
4-20mA Signalisation LED (yellow), per input
Shunt-Impedance 50 Ohm
Resolution 12 bit + VZ
BO (Binary Output)
Relay contact NO, isolated
Common mode voltage +/- 8VDC
Max. contact current 8A
Error on delivery ≤ 0,1% at 25°C
Max. contact voltage 250VDC
Temperature drift ≤ 100ppm/K (0 .. 70°C)
Max. switching power 120W resistive
Linearity ≤ 0,1%
50W at L/R=40ms
Line frequency 50Hz, 60Hz, Signalisation LED (yellow), per input
16 2/3 Hz
Line frequency interfer- > 100 dB ALR (Alarm Output)
ence suppression
Alarm (ALR) NC, isolated
Relay contact
BI (Binary Input R0001)
Max. contact current 8A
Voltage 24 / 48 / 60VDC (+/-20%)
≥ 18V = Logic 1 Max. contact voltage 250VDC
≤ 9V = Logic 0
Max. switching power 120W resistive
Input current 2mA constant
50W at L/R=40ms
Over-voltage protection Max. 72VDC
MSS (Main Supply Supervision)
Reverse voltage protec- yes
tion MSS 24V, 48V, 60VDC
Max. input signal fre- 120Hz Digital Input ≥ 18V = Logic 1
quency Channel 1 up to 16KHz ≤ 9V = Logic 0
Electrical Safety
EN60950-1 Electrical Safety investigation
Safety class 1 Flammability investigation
EN60255-5 >100MOhm@500VDC
Isolation SELV – Process
Process - Process
Environmental conditions
Temperature -40 °C start up
-25 °C … +70 °C operation
-40 °C … +85 °C storage
IP class IP 30
Relative Humidi- 5 … 95 %
ty (non condensing)
Ordering information
Note:
We reserve the right to make technical changes or modify the contents
of this document without prior notice With regard to purchase orders,
the agreed particulars shall prevail. ABB AG does not accept any
responsibility whatsoever for potential errors or possible lack of infor-
mation in this document.