Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Splitter
User Manual
V1.0
Copyright
Copyright © 2004 by Shenzhen Huawei Technologies Co.,Ltd. .
All rights reserved.
The information in this document is subject to change without notice. No part of this
document may in any form or by any means (electronic, mechanical, micro-copying,
photocopying, recording or otherwise) be reproduced, stored in a retrieval system or
transmitted without prior written permission from Huawei Technologies Co., Ltd.
JPX321-BM2/3-128B/A 宽带模块及 AS-5K/6X 话音分离器 用户手册 目录
Contents
are used to deploy ADSL service. DSLAM signals can be separated from
W
D
90¡ ã
Figure 1
office cable and connect jumper, as well as test and open circuit.
-1-
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
H×W×D=248×160×100mm;
96F module to separate the narrowband signals and broad band signals.
Figure 2
1.1.3 Accessories
The accessories include IDC tool, testing plug, switching plug and open-
connection tool with wire-cutting device. This IDC tool contains hooks for
Figure 3
-2-
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
should be removed.
Figure 4
Figure 5
modules ;
In expansion mode : connect POTS signal and disconnect the DSL signals;
signals.
-3-
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
figure 6
Take off the 16 8-loop strips from JPX321-BM2-96F module with tools, such
as screwdriver.
module to give facility for user installation. There are 2 installation mode,
shown as following:
-4-
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
2 1
Figure 7
1.3.1 Cabling management for DSLAM data cable ,voice cable and jumpers
Remove the 8-loop module strip first when deploying the DSLAM cable;
When deploying the DSLAM cables, remove the jacket of data cables and
voice cables of DSLAM and organize these cables first; and group the
-5-
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
The jumpers of internal and external lines are managed through the cable-
guiding ear, in which the internal line jumpers are led to the corresponding
module strip via the guiding-holes and then clamped; the external line
jumpers are led to the corresponding module strip via the space between
3&4
-6-
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
1&2
jumper(JUMPER)(square mark■)
Figure 8
1. Coloring the 8-pair cables led to the back of the module strip with color
mark;
3. Fastening the cables from the threading trays to the front of module strip
4. Clamping each cable to the front of the module strip with IDC tool.
1.3.2 Deploying the DSLAM data cable ,voice cable ,external line
jumper, narrowband jumper
-7-
4 3
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
1 2
(square mark■)
Figure 9
Plug the voice splitter into the slot of the 8-loop module bar. Make sure it is
-8-
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
1 2
Figure 9
For splitter maintenance, loosen the two captive screws on the module, turn
downwards ( limited position 75° ) ,and pull out the splitter to give some
proper maintenance. Make the module return to its original position after
90¡ ã
Figure 10
Insert the testing plug and open-circuit plug into the broadband module,
shown as following:
-9-
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
1 2
Figure 11
structure. Insert the plug into the corresponding slot of 8-loop module and
1 2
1 2
Figure 12
The IDC tool clamps each conductor into corresponding terminal. After
pushing in position, it will automatically cut off the burrs, shown as following:
- 10 -
JPX321-BM2-96F Broad band Module and AS-8K Splitter User Manual
Figure 13
- 11 -