Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
WASHING MACHINE
FULL AUTO INVERTER
MODEL
ES-F1408X-SL
In the interests of user-safety (Required by safety regulations in some countries) the set
should be restored to its original condition and only parts identical to those specified
CONTENTS
1. SPECIFICATIONS………………………………………………………………………………… 1
2. ABNORMAL CONDITION…………………………………………………...…………………… 2
3. CIRCUIT DIAGRAM…………………………………………………………………………………4
4. TROUBLESHOOTING …………………………………………………………………………… 4
5. DISASSEMBLY PROCEDURE……………………………………………………………………10
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace
these parts with specified ones for maintaining the safety and performance of the set.
SPECIFICATION
Power source AC 220V, 50Hz
Overall dimension 680x695x1065
Net weight 60kg
Power consumption 300W
Motor output 140W
Waterproof Grade IPX4
Washing &Spin Capacity 14kg
Water capacity 107Liters
ABNORMAL CONDITION
When the washer is abnormal, the washer stops as the every actions turns off, beep tone sounds
ON-0.1 second and OFF-0.1 second for 6 seconds and number window LED display abnormal
code and blink on and off. The washer judges the following six conditions as abnormal condition.
The number window LED display abnormal code: and begin blinking on and off at the
same time and the electric buzzer sounds to indicate a problem.
The number window LED display abnormal code: and begin blinking on and off at the
same time and the electric buzzer sounds to indicate a problem.
7) Other Item
CODE
abnormal condition method of disposition
TROUBLE SHOOTING
a. Power Source
Yes
Any indications Is fuse blown? Deterioration of fuse. Replace.
and beep do not Motor is defective. Replace.
work when Capacitor is defective Replace
power switch is
on and the start No
button is pressed
Poor connect of Repair or replace.
connectors
Control circuit board is
Replace.
defective
b. Water Supply
Cushion Replace.
Water valve is defective.
Filter Water level sensor is
Replace.
defective.
“magic”joint assembly Control circuit board is
defective. Replace.
Water is not Check water Low Remove the flow
supplied normally. sheet of the water
pressure.
valve.
Note: When removing the flow sheet, reinstate the filter in place correctly.
Water does not stop Does water stop Something in the air trap
when the plug hose or air leaks from a Clean or replace.
is removed or Yes part related water level
power switch is sensor system.
OFF? Water level sensor is
Replace .
defective.
Control circuit board is Replace.
No defective.
c.Wash/Rinse
No
Washing cycle does Does the spin tub Bearing ass’y is defective. Replace.
not start even if rotated normally Poor connect of
Replace.
water keeps the when the connectors
selected water level. PROGRAM Thermostat on motor is Repair or replace
button opened. after cooling down.
is set to SPIN? Control circuit board is
Yes defective. Replace.
Yes
Motor coil shorten. Replace.
Capacitor is defective Replace.
Is the torque
The spin tub rotates motor working Yes Brake lining on bearing Replace bearing
together with the normally. ass’y is worn out. ass’y.
pulsator during Brake lever ass’y is
washing or rinsing defective. Replace bearing assy.
cycle.
No
Torque motor is broken. Replace.
Note:
Break-work is Does brake-work
No
Brake lining is worn out. Replace bearing ass’y.
normal when spin normally? ’
Brake lever ass y is defective. Replace bearing ass’y.
tub stops within 10
sec. under no-load.
d. Drain
Is the built-in pump
Yes
Water does not Foreign matter in drain Clean drain hose
drain out. working normally? hose. inside.
No
Pump lead wire is Repair or replace.
disconnected.
Control circuit board is Replace.
defective.
ES-F1408X-SL
e. Spin Drying
Yes
Spin drying cycle Does safety Machine inclines. Replace with level.
does not work.
device work?
No
Small pulley mounting Tighten up.
screw is loosed.
Note:
Motor is disconnected or Replace.
1. The tub switch works 3 times
continuously or works 1 time in the burnt.
single program of spin-dry. The Capacitor is broken or Replace.
number window LED display abnormal disconnected.
code: and begin blinking on and
off at the same time and the electric Bearing ass’y is defective. Replace.
buzzer sounds to indicate a problem. Torque motor is defective. Replace.
2. Do not disconnect the wire from the Brake lever is defective. Repair or replace.
capacitor, because this wire acts as
de-pressing noise from outside to the Thermostat on motor is Repair or replace
micro-computer. opened. after cooling down.
Poor contact of 6-pin Repair or replace.
connectors (blue &white).
Control circuit board is Replace.
defective.
ES-F1408X-SL
Automatic
adjustment or Stop of Spin-Dry Water supply
load.
Agitation of load
(Rinsing ).
When the safety device works by abnormal swing of spin drum, machine works automatically to
stop Spin-Dry cycle and operates water supply valve to pour water into the Wash/Spin Tub and
then starts washing cycle for replacing washing clothes evenly.
After above operation has down twice, if safety device works again, machine will stop, and the
number window LED display abnormal code: and begin blinking on and off at the same time
and the electric buzzer sounds to indicate a problem.
• Open the Wash Lid and rearrange the clothes evenly around the Wash/Spin Tub.
• Close the Wash Lid and press the START/PAUSE button again.
Buzzing/rattling IsINSPECTION
high water Low Something in water valve. Replace.
during water pressure (more
supply. than 4kg/cm2)?
Is clattering on
maximum Motor pulley is loose. Tighten up.
rotation?
4 safety switch
seperate the
11 inverter PCB main PCB and
inverter PCB
PREPARED BY,
CS PROMOTION CENTER
SHARP ELECTRONICS (M) SDN BHD
SHAH ALAM, SELANGOR, MALAYSIA