Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. As per SNT-TC-1A the Near vision acuity exam is to be done – Once in a year or
at the desecration of the employer
5. As per CP-189 for Le-II practical exam min. No. of check points requiring an
understanding of NDT variables and employer’s procedural requirements should be
included
SNT – Minimm 10 , CP –Only Written Check list
7. As per SNT-TC-1A, the NDT Le- I method requiring the min. experience
Method, VT,MT,& PT 70 Hours, Technique BLT-3 hours
9. As per CP-189 for Le-II practical exam min. No. of samples recommended per
method is 2, Per Technique is 1
12, As per SNT-TC-1A, the max. recertification period for all levels 5 years
13. As per CP-189 for near vision acuity testing the applicant should be able to read
a min of J1
15. As per SNT-TC-1A, a persons fails in Le-II exam is permitted to take re-exam
without undergoing retraining After 30 days
16. Creep of metals refers to-High Tem Problem, Time Temp & Stress, Time
Consuming test ( Minimum 1000 Hours Required) Creep strength is defined as the
stress required to produce the creep rate of 1% in 10,000 hours
19. Max. qty. of steel is produced by this method- Basic Oxygen Process
23. The tensile stress in a bar of L=15” and W=3”, T=2” subjected to tensile load,
acting along the length, of 3000 pounds will be- 3000/ ( 3x2)= 500 Psi
24. Many metals exhibit an increase in strength caused by plastic flow beyond elastic
limit. This effect is known as Work Hardening/ Cold Working
27. Notched bar testing is carried out to find – Impact Tests – Impact Toughness or
Notch Toughness ie To measure the energy absorbed
32. Which of the following has least ductility : Gold, Copper, Aluminium, Cast iron
34. Engg. Stress-strain curve is generated on the basis : That original Specimen size
did not change Understanding of the tensile test can be had from Stress /Strain
Diagram
35. The welding process that is more frequently carried out in vacuum- EBW
36. The welding process using non consumable electrode with arc maintained in an
atmosphere of inert gas-GTAW
39. When used with respect to machine tools NC means- Numerical Control
40. The welding process capable of producing very high intensity and rate of heat
- PAW
42. To avoid quench cracks during heat treatment of steel, one should use- Tempering
43. Many metals exhibit an increase in strength caused by plastic flow beyond elastic
limit. This is called Cold working or Work Hardening
44. Hardness measured with what max. test load is called microhardness Few
Hundred Grams – Anyway Check
44. Brittle fracture is promoted by – Low Temperature, High Thickness
45. Crystal structure, generally exhibiting highest ductility & toughness is- Face
Centered Cubic
46. Identify more severe flaw- Lemaller Tear, Lamination, Shrinkage, Porosity
47. Cheapest alloying element for increasing strength & hardness of steel is - Carbon
48. If the sensitivity of halogen Leak detector is mainted constant throughout a test,
which of the following is true From The Book LT 8
56. The best type of magnetizing current for testing of fatigue cracks AC
59. Which following generators would produce the narrowest cone of radn.- Highest
energy
60. Which following Converter screen can NOT be used for indirect technique in
NRT_ Gadolinum
61. Ultrasonic sound velocities are different for different materials because Their
Density & Young’s Modulus e different
77) What materials is usually used as the electrical relay spring where high
conductivity has to be combined with high endurance limit
a) aluminum
b) copper
c) steel
d) Alloy of 98 % Copper & 2 % beryllium