Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
OF MADHAYA PRADESH
PANCHAYAT & RURAL DEVELOPMENT DEPARTMENT
RURAL ENGINEERING SERVICE
g.orio,-S0 sf
^ f\-J
/ zz /fu.-to /rwrt / n,
qfuftTfu,-
l. ft-q q+fuq qr+fiq ri4-{d gq rffiq fufit-rr frqrq t
2. qufglox Tflfu-w
qeqq-erT I
{^,'*
oTR?idr
qiBr+t +qr
rArT .frqrd
FirstScheduleofRates(SoR)forRuralEngineeringServicesforimplernentationof
1995' lt was subsequently revised few
works done by the Departrnent was issued in october
Since then there has been lot of changes
times and last revision was effective w.e.f . 01.02.2016.
keep pace with the movement of
in the cost of construction material and labour' In order to
SOR has been proposed' The present SOR is an outcome
of inputs from
market price this new
and labour. we have also included
field functionaries on various rates of materials, machinery
about 1685 items which were not envisaged at the
time of preparation of SoR Software in year
rate analysis of such items was not available in
2003 have also been included. As comprehensive
PWD SOR and other relevant SOR' These items
the software such items have been adopted from
have been included in ChaPter 25'
WhereveranyreferenceismadetoanylndianStandard'itshallbetakenasreferenceto
ln the event of any variation between the
the Iatest edition with all amendrnents issued thereto'
over the
pwD nomenclature (adopted) and the Indian Standard, the former shall take precedence
latter.
PreparationandrevisionofanySchedu|eofRatesisahighlytechnicalandarduoustask
S. K'
and require lot of efforts to accomprish. I
wish to prace on record the efforts made by Shri
Satish Tiwari E,E (lncharge), Shri Ravi
Khare SE, Shri p.K. Nigam CE (lncharge), Shri
chachane AE, Smt. Noopur vishwakarma S/E,
Shri P'c' Bagri S/E and all engineers of RES
considerabry to this job. l would like to thank
famiry from fierd and office who have contributed
suggestions' This new SOR would be
all field engineers who provided useful feedback and
effective from l't Nov' 2017'
manr rn the snhe^rrl re will be highly
Suggestions,ifany,forimprovementtotheScheduleofRatesatanyttn
appreciated.
Bhopal
Dated 30'n Oct. 20 | 7
(P.D. Khaira)
Engineer in Chief
Rural Engineering Service
MadhYa Pradesh
INDEX
CHAPTER CHAPTER NAME PAGE No
00 GENERAL 1-6
01 JUNGLE CLEARANCE 7-8
02 MORTARS 9-10
03 EXCAVATION 11-15
04 FILLING FOUNDATION, CONCRETE WORK 16-19
05 STONE MASONRY 20-22
06 BRICK MASONRY 23-25
07 WOODWORK AND JOINERY 26-33
08 CEILING AND WALL BOARDING 34
09 IRONWORK 35-40
10 PLASTERING AND POINTING 41-46
11 ROOFING 47-50
12 PAVING, PITCHING AND FLOORING 51-56
13 PAINTING, WASHING AND DISTEMPERING 57-63
14 REPAIR TO BUILDING WORK 64-65
15 DISMANTLING AND DEMOLISHING 66-68
16 MISCELLANEOUS -I 69-70
17 SURVEY AND INVESTIGATION 71-72
18 COLLECTION OF MATERIALS 73-75
19 TRANSPORTATION OF MATERIALS 76-79
20 ROADWORK 80-86
21 WATER SUPPLY & FITTINGS 87-94
22 SEWAGE, DRAINAGE AND SANITARY FITTINGS 95-101
23 SPECIAL ITEMS OF EARTH/MASONRY DAM AND 102-103
CANALS
24 WELL EXCAVATION 104
25 MISCELLANEOUS - II 105-132
26 ANNEXURE – 1 TO 13
27 APPENDIX – A TO G
Page 1 of 132
00 - GENERAL
0.1.01 In the absence of any stipulations to the contrary, unit rate for various items of works
are for completing works to the requirements of the specifications including full
compensation for all operations & inclusive of all labour, materials, royalties, lease rent,
wastages, temporary work, plant, equipment, over head charges and profit, unless specified
otherwise.
0.1.02 The mode of measurements shall be as per provisions content in the relevant chapters
and items of the specifications, unless specified otherwise.
0.1.03 The rates include the element of higher and running charges of all types of plants,
machinery and equipment, required to complete the work, unless specified otherwise. The
rates provided in this schedule of rates include, cost, lead, lift of all materials required for
execution of works inclusive of all charges like duties, octroi, tax, royalty, insurance etc. as
may be applicable, all labour, all lead and lift (unless otherwise specifically provided for)
including performance all workmanship, provision for erection and removal of centering
forms scaffolding, benching, ladders, templates, tools and plants and all other applications
etc. required for the proper execution of work unless otherwise specified. Provisions for
covering etc. necessary to protect the work / structure from inclement weather etc. and
damage arising from falling materials or other cause such as rain, fire etc. shall be
contractors responsibility. Rates are also inclusive of curing wherever required including
arrangement of water and its lead or lift whatsoever.
0.1.04 The labour only provided in the schedule of rates includes the cost of all labour
including necessary machine, tools, scaffolding, handling of materials at site of works, all
workmanship and including the cost of scaffolding, curing, any sundry material like nails,
spikes, water etc. and as detailed above, but does not include the cost of main material,
which means materials shall be made available at or near the site of work. The rate includes
provision of handling, storing under cover as required.
0.1.05 The rates also include the element of testing of samples of various materials brought
by the contractor for use on the work, as well as other necessary tests for items of work as
stipulated in the specifications. Frequency of such tests to be carried out must not be less
than the prescribed frequencies. Copies of registers, containing records of tests shall have to
be presented along with running account bills. Register (original) shall have to be submitted
along with the final bill. Tests shall have to be conducted by the contractor's Engineer under
the supervision of the Engineer-in-charge or his authorized representatives. The contractor
shall have to establish a field laboratory at the site of work, if the amount of contract exceeds
Rs. 25.00 lacs. In other cases where amount of contract is between 5 to 25 lakhs, testing of
construction materials should be got done from any of the tests laboratories of the various
Govt. Departments, Government/Semi Govt. under takings and Technical Institutes,
Engineering College, Polytechnic, I.T.I. etc.
(a) The work should not be accepted in any case, if the contractor fails to observe the
instructions of the department, regarding testing of materials.
(b) Before making any payment, it will bet the responsibility of the officers making payment
to assure that all tests as per prescribed frequencies, have been carried out, and found as per
requirement.
(c) If tests are not conducted to the prescribed frequency, the Engineer in Charge should
reject that part of the work.
0.1.06 All material shall conform to the relevant Indian Standard Specification prevailing on
the date of issue of notice inviting tender. All materials before use in work shall require
approval of the Engineer in Charge, who will get them tested sampled as per relevant IS
Code 1S:5454:1978 at contractor's cost and samples so approved be kept in the office of the
concerned sub divisional officer till finalization of the work.
0.1.07 It will not be obligatory on the part of Engineer in charge to provide any assistance in
obtaining of lease/permits for extraction of minor minerals. The contractor will not be entitle
to any excuse, whatsoever, on account of any delays in obtaining minor minerals to be used
on the work.
0.1.08 Not withstanding any thing to the contrary, aggregates to be used for all cement
concrete items shall be crushed in the mechanical crushers. All concrete shall have to be
mixed in power driven mixtures having hoppers and capacity of mixing concrete mix of
atleast one bag of cement.
0.1.09 Nothing extra shall be payable on account of use of Narmada sand or sand brought
from any other quarry / river. Sand should conform to the requirements of IS: 1542 and IS:
2166 for using it in construction work.
0.1.10 When cement is used for mortar/volumetric mix etc. batch of one bag cement or its
multiples shall be mixed and the measurement of box for metal, sand to be of 35 litres or
multiples of it (convenient box size 40x35x25 cm). For design mix concrete batching shall
be done by weight.
0.1.11 Rates in this S.O.R. would also apply for works (Administrative approval upto Rs.
2.00 Lakhs) on piece work/work order system. Rates payable for any item of work proposed
to be done under this system may either be at par or below the rates in this S.O.R.
0.1.12 Rubble available from excavation of hard rock shall be property of the contractor
subject to recovery of Rs. 150 per cum of the quantity of the rock excavated.
0.1.13 The contractor shall have to provide a ruled duplicate register at site named "Site
order book". It shall be in the custody of departmental supervisory staff. The
Engineer-in-Charge or his authorized representative may record his instructions in this book,
which shall be noted by the contractor or his authorized representative for compliance.
0.1.14 Teak wood shall not be used in any building work unless specific sanction of the State
Government is obtained.
(a) Provision of teak wood shall not be made in any of the estimate without prior sanction of
the State Government.
0.1.15 Where contract provides for cement to be arranged by the contractor himself, only ISI
mark cement of relevant IS specifications shall be allowed to be used in the work subject to
the following tests. The arrangement for necessary equipment and testing shall have to be
made by the contractor himself at site, to be decided by the Engineer-in-Charge. All
expanses shall be borne by the contractor. Any lot of cement brought to site by the
contractor, would be permitted to be used in the work only after the satisfactory results of the
tests, under the supervision of the Engineer-in-Charge or his authorized representatives. The
record of the tests result shall be maintained in the register referred in subsequent para.
a. Test for initial & final setting time as per IS: 3536-1996 1 Test for 10 tonnes or part
thereof upto 10 tonnes.
b. Test for determination of compressive strength of cement as per IS: 3536-1996 1 Test for
50 tonnes or part thereof upto 10 tonnes.
0.1.16 A duplicate register as per format here under shall be maintained at site of work.
Extract certified copies of the entries for each month shall be submitted to the
Engineer-in-Charge by the contactor. The original register shall also be submitted to the
Engineer-in-Charge on completion of the work by the contractor.
----------------------------------------------------------------------------------------------------------------
S.No. Date of No. Name Signature Signature Result of Result of Remark
receipt of and of of authorised test for of tests
of cement bags address contractor representative initial for
of firms, or his of Engineer- and final compressive
from authorised in-Charge setting strenght
representative time of cement
----------------------------------------------------------------------------------------------------------------
0.1.17 When the strength of concrete required is upto M-20, then OPC confirming to IS
269-1989 or PPC confirming to IS : 1498-1976 may be used.
0.1.18 When the strength of concrete required is more than M-20 but upto M-30, then OPC
confirming to IS : 8112 - 1989 shall be used.
0.1.19 Nominal mix would be adopted for cement concrete M-7.5, M-10, M-15 and M-20.
Design mix shall have to be adopted for concrete of higher strengths.
a) Mild steel and medium tensile steel bars shall conform to IS : 432 (Part-I).
b) Hot rolled deformed bars shall conform to IS : 1139.
c) Cold Twisted bars shall conform to IS : 1786.
d) Hard drawn steel wire fabric shall conform to IS : 1566 and
e) Rolled steel made from structural steel shall conform to IS : 226.
0.1.21 All reinforcement shall be free from loose mill scales, loose rust and coats of paints,
oil, mud or other coating which may destroy or reduce bond.
0.1.22 The contractor shall have to produce Test Certificate in the proforma prescribed
approved by BIS from the manufacturer for every batch of steel brought to site of work.
0.1.23 Only such steel as is obtained from main producers of steel e.g. SAIL, IISCO,
TISCO or such steel rolling mills as are having licence from the B.I.S to manufacture such
steel for reinforcements, shall to be allowed to be used in the work.
0.1.24 The rates for various items in this SOR are subject to stipulations in these "General
Notes".
0.1.25 Items not included in this SOR shall neither be provided in any estimate nor executed
without express prior permission of the Chief Engineer even though shown in the drawings
prepared by the Chief Architect or any Consulting Architect. If any new or modified item is
proposed to be provided in any estimate or intended to be executed in any work, proposals
with full justification thereof along with financial implication must be submitted to the Chief
Engineer for obtaining prior approval.
0.1.26 In case of any contradiction in the provisions of the specifications and the SOR, the
provisions of the latter would take precedence.
0.1.27 The rates as given in this schedule for all items are final, binding and conclusive. In
case of doubt and printing mistakes if any, the decision of the Chief Engineer will be final
and binding.
0.1.28 In the interpretation of description of items or rates of the schedule of rates and
specification, the decision of the Chief Engineer shall be final and binding.
0.2 DEFINITIONS :
a) Specifications would refer to the Central Public Works Department (CPWD)
specifications as applicable as on date.
b) Engineer-in-charge would refer to the Executive Engineer of the Rural Engineering
Services Division for the time being. It would also refer to the "Engineer" mentioned in the
aforesaid specifications.
c) B.I.S. would refer to Bureau of Indian Standards.
The following terms and expressions in this schedule shall have the meaning or implication
hereby assigned to them unless otherwise specified elsewhere.
0.2.01. Contractor - The 'contractor' shall mean the individual or firm or company whether
incorporated or not undertaking the works and shall include the legal personal
representatives of such individual of the persons composing such firm or company, or the
successors of such individual or firm or company and the permitted assignees of such
individual or firm or company.
0.2.02. Engineer-in-charge - The 'Engineer-in-charge' means the Executive Engineer who
shall supervise and be in-charge of the work and who shall sign the contract on behalf of the
Governor.
0.2.03. Site- The 'Site' shall mean the land/or other places on. in. into or through which the
work is to be executed or any adjacent land, path or street through which the work to be
executed or any adjacent land, path or street which may be allotted or used for purpose of
carrying out the work.
0.2.04 Store - The 'store' shall mean the place of issue of materials included in the
appropriate schedule for issue by the R.E.S. In all other cases ' store' shall mean any R.E.S.
0.6.01. In booking dimensions, the order shall be consistent and the sequence of length, the
width and height or depth or thickness.
0.6.02. Rounding off - Rounding off where required shall be done in accordance with IS:
2-1960. The number of significant places rounded in the round off value should be as
specified.
0.7. SAFETY IN CONSTRUCTION :
0.7.01. The Panchayat and Implementing Agency shall employ only such methods of
construction, tools and plant as are appropriate for the type of work or as approved by
Engineer- in- charge in writing.
0.7.02. The Panchayat and Implementing Agency shall take all precautions and measures to
ensure safety of work and workman and shall be fully responsible for the same . Safety
pertaining to construction works such as excavation, centring and shuttering, trenching,
blasting, demolition, electric connections, scaffolds, ladders, working platforms, gangway,
mixing of bituminous materials, electric and gas welding, use of hoisting and construction
machinery shall be governed by CPWD Safety code, relevant safety codes and the directions
of Engineer-in-charge.
0.8. ABBREVIATIONS:
The following abbreviations, wherever they appear in the schedule of rates, shall have the
meaning of implications hereby assigned to them.
AC Asbestos Cement ASTM American Society for testing materials
BC Black cotton BM Bench Mark
BWG British Wire Gauge Bt Black Trap
C Degree centigrade
temperature CC Cement Concrete
CG Centre of gravity CGS Corrugated Galvanised sheet
CI Cast iron CL Centre line
cm Centimetre CM Cement mortar
CR Coursed rubble cucm Cubic centimetre
cum Cubic metre cumec (s) Cubic metre per second (s)
Dia Diameter DRR Diesel road roller
D\S Downstream etc. Etcetra
e.g. For example ERW Electric resistance welded
E\ W Earth work GI Galvanised iron
KVA Kilo volt ampere LM Lime mortar
LWL Low water level m Metre
MDD Maximum dry density mm Millimetre
MS Mild steel MTS Medium tensile steel
N/ Sqmm Newton per sq mm NMR Nominal muster roll
OMC Optimum moisture content PCC Plain cement concrete
POL Petrol oil and lubricant pt Part
PVC Polyvinyl chloride r radius
Re Rupee Rs Rupees
RCC Reinforced cement concrete q quintal
RR Random rubble RS Rolled steel joist
SDO Sub-Divisional Officer Sqm square metre
GL Ground level HP Horse power
I.e. That is IRC Indian road congress
---------------------------------------------------------------------------------------------------
0101 Site clearance, cutting grass, raking into heaps and removing off the sqm. 3.4
premises
0102 Jungle clearance including uprooting of rank vegetation, grass, brush sqm. 8.4
wood, saplings and tree not exceeding 30cm girth and removing not
exceeding 50meters outside the periphery of the area cleared.
0103 Deduct from items 0102 for uprooting not done. sqm. 5.0
0104 Cutting down trees (exceeding 30cm girth, grubbing uproot, filling pits
and levelling off ground, lopping branches, trimming, removing not
exceeding 50meter & staking serviceable material and cleaning site.
(a) Girth exceeding 30 cm and not exceeding 100 cm Each 1460.1
(b) Girth exceeding 100 cm and not exceeding 150 cm Each 2526.4
(c) Girth exceeding 150 cm and not exceeding 200 cm Each 2917.0
0104 Cutting down trees (exceeding 30cm girth, grubbing uproot, filling pits
and levelling off ground, lopping branches, trimming, removing not
exceeding 50meter & staking serviceable material and cleaning site.
(d) Girth exceeding 200 cm and not exceeding 250 cm Each 3405.9
(e) Girth exceeding 250 cm and not exceeding 300 cm Each 3888.1
0105 Deduction from items 0104 (a) to 0104 (e) for uprooting not done. Each. 50% of
respective item
0106 Uprooting of roots of trees including removing and stacking (Girth to be Each. 50% of
measured at 1.00 m above G.L.) respective item
0107 Ordinary shrub jungle (areas below 25% covered by shrubs) clearance sqm. 1.2
involving removal of grass. Shrubs, bushes and twigs, excluding uprooting
(for survey works)
0108 Medium shrub jungle (25% to 50% area covered by shrubs) clearance sqm. 2.4
involving removal of grass. Shrubs, bushes and twigs, excluding uprooting
out (for survey works)
0109 Thick shrub jungle (area above 50% covered by shrubs) clearance sqm. 3.6
involving removal of grass. Shrubs, bushes and twigs, excluding uprooting
out (for survey works)
0204 Lime Surkhi Mortar 1:1:1 ( 1 lime putty, 1 surkhi, 1sand ) cum 1742.7
0205 Lime Surkhi Mortar 1:1:2 ( 1 lime putty, 1 surkhi, 2sand ) cum 1628.0
0206 Lime Surkhi Mortar 1:2 ( 1 lime putty, 2 surkhi,) cum 1639.9
0207 Labour only for lime mortar & lime surkhi mortar cum 567.7
0215 Cement Lime Mortar 1:1:3 ( 1 cement, 1 lime putty, 3 sand ) cum 3186.1
0216 Cement Lime Mortar 1:1:4 ( 1 cement, 1 lime putty, 4 sand ) cum 3119.6
0217 Cement Lime Mortar 1:1:5 ( 1 cement, 1 lime putty, 5 sand ) cum 2738.9
0218 Cement Lime Mortar 1:1:6 ( 1 cement, 1 lime putty, 6 sand ) cum 2432.8
0219 Cement Lime Mortar 1:1:8 ( 1 cement, 1 lime putty, 8 sand ) cum 2109.1
0220 Cement Lime Mortar 1:2:9 ( 1 cement, 2 lime putty, 9 sand ) cum 2195.4
0221 Cement Lime Mortar 1:3:12 ( 1 cement, 3 lime putty, 12 sand ) cum 2076.7
0223 White cement mortar 1:2 ( 1 White cement, 2 Marbel dust) cum 8956.1
3.1.1 The length, breadth and depth (or height) shall be measured correct to the nearest cm.
If the measurements are taken with level and staff, the levels shall be recorded correct to 5
mm. The area shall be calculated in Sqm. correct to two places of decimal and cubical
contents in cum correct to two places of decimal.
3.2.Classification of Strata -
(a) Loose or soft soil - Generally any soil which yields to the ordinary application of pick
and shovel, or to spade, rake or other digging implement, such as vegetable or organic soil
turf, gravel, sand, silt, loam, clay, peat, etc.
(b) Hard or dense soil- includes all materials which can be removed with shovel or spade
after loosening with pick axe, such as clay, soil mixed with lime kanker, black cotton soil
for earthen bund, soft moorum etc.
(c) Hard moorum and moorum mixed with boulders. - Generally any material which
requires the close application of picks, jumpers or scarifies to loosen, such as hard and
compact moorum and soft shale. Moorum or soil mixed with small boulders not exceeding
25 % in quantity and each less than 0.014 cum (300 mm dia or 1/70 cum) but more than
0.004 cum in size. " Boulder is a rock fragment usually rounded by weathering,
disintegration or exfoliation or abrasion by water, found lying loose on the surface or
embedded in material of dissimilar origin "
(d) Disintegrated or soft rock - Disintegrated or soft rock include such strata's which
require the close application of crow bars, picks, grafting tools and scarifies in suitable
combination for its excavation such as soft laterite, soft conglomerate hard shale, soft
copra hard and compacted moorum mixed with small boulders exceeding 25 % in quantity
but each not exceeding 0.014 cum in size and soft rock comparies of the following -
(i) Boulders (dia more than 300 mm but not greater than 0.50 cum in volume) hard laterite,
hard copra and hard conglomerate or other rock which may be quarried or split with crows
bars, with casual blasting, if required, for loosening of strata.
(ii) Any rock which in dry state may be hard, requiring blasting, but when wet becomes
soft and manageable by means other than blasting.
(e) Hard rock (requiring blasting) - Any rock or boulder (more than 0.5 cum in volume)
which requires use of mechanical plant or blasting for excavation or splitting.
(f) Hard rock (Blasting prohibited) - Hard rock requiring blasting as described under (e)
but where blasting is prohibited for any reason and excavation has to be carried out by
chiselling, wedging or any other agreed method.
3.3 Authority for classification :- The classification shall be decided by the Executive
Engineer and his decision shall be final.
3.4 Dressing - (a) Dressing is normally required at one place i.e. at the place of excavation
or at the place of filling hence the rates provided in the schedule include dressing only
once, either at the place of cut or at the place of fill. In case of canal excavation, where
earth is reused at or near the same place and for the same work, in such case only one
dressing which is already included in the basic rates is admissible, even though the
dressing is actually needed at both the places i.e. at the place of cut and at the place of fill,
Page 12 of 132
while additional rate for trimming in cutting only will be payable.
(b) In case, dressing is not done either in cut or in fill or both rate for dressing will be
reduced.
(c) No separate payment for dressing or trimming of spoil bank (s) and borrow area (s)
shall, be made.
3.5 Trimming -
(a) This comprises of removing grass and grass roots, touching the uneven surface (either
horizontal or slopping), by scraping off high patches and filling in low patches with the
scraped soil. The maximum depth of cutting or not exceeding 15 cm.
(b) This item of work shall however, not be payable for road work maintenance of
approach roads, service roads, etc. as well as where payment for dressing in earth work/
excavation has already been made.
3.6 Wet excavation.- Extra rate for excavation will be payable only for excavation below
sub-soil water level Trial pits shall be dug in the area where excavation is required to be
done. The steady water level in the trial pits which is left undisturbed for 48 hours before
the pumping operations are started, shall be considered as sub-soil water level in the area.
3.7 Rates for items 0301 to 0309 include 50m. free lead and 1.5 m. free lift.
3.8 Lifts.
(a) Lift for all modes of handling has to be measured in an upward direction, i.e. when the
materials are moved against the force of gravity.
(b) Lift will be calculated on the height of the centre of gravity of the lifted material above
the average of ground levels at the Centre as well as upstream and down stream toe at
section of the dam/embankment. For working out extra lift payable, the initial 1.5 m free
lift shall be deducted.
(c) In the case of earthwork for canals in partial or full cutting, lift will be calculated on the
completed section of the work done from the centre of gravity of the cutting portion to the
centre of gravity of embankment minus 1.5 m free lift.
(d) In the case of canal excavation where spoil bank is formed in number of sections, more
than one, the quantity in each spoil bank has to be fitted into the canal excavation. The lifts
payable will be for the centre of gravity of excavated portion to the centre of gravity of the
corresponding spoil bank minus 1.5m free lift.
(e) No negative (downward) lift shall be payable for earth work /excavation.
(f) The estimate for Earthen dam embankment be sanctioned on the basis of approved
designs considering utilisation of useful available materials from excavation of approach
spill channel (s). The estimate for approach/spill channel (s) be sanctioned only for the
balance excavation which cannot be utilised. The payment shall also be made accordingly.
For the entire excavated materials of approach /spill channel (s) lift is payable from the
centre of gravity of the excavated portions to the centre of gravity of the banks and
deductions of 1.5 m free lift shall be made to work out the extra lift payable. However, for
the useful materials transported to the dam/ embankment lift would be payable, as per (c)
above.
3.9. Lead
(a) Extra lead for earthwork by head load beyond initial 50m free lead will be payable for
every additional 50m or part there of up to a total distance of 200m.
(b) The lead for earthwork shall be measured from the centre of borrow area (s) to the
centre line of the dam/ embankment and shall be measured as crow flies, the crow fly
distance being measured from the geometrical centre of borrow area (s) to the centre of the
dam/embankment. While calculating the lead for payment an additional five percent over
the distance calculated above shall be added to cover circuitous path.
(c) The extra lead charges for earthwork when total distance exceeds 200m (head load
Page 13 of 132
lead) will be payable as per chapter "TRANSPORTATION OF MATERIALS".
3.10.Bailing out water.-
(a) Rates do not include any allowance for bailing out of water.
(b) For excavation done departmentally the bailing out of water not requiring pumping,
shall be done as a separate items, as per actual expenses. The decision of the Executive
Engineer, as to whether or not pumping is necessary for bailing out water in any particular
case, shall be deemed as final.
3.11. Rates of items 0301 to 0309 include the following : -
(a) Separation of serviceable and unserviceable material and depositing them separately in
regular heaps or stacks as directed. Where stacking of material is done under specific
orders of the Executive Engineer with a view to utilise the entire materials on other items
of works, separate rate for stacking shall be payable.
(b) Forming (or leaving) 'dead men' to ' tell-tales' in borrow pits and their removal after
measurements.
(c) Removing slips or falls in excavations.
(d) Forming (or leaving) steps in sides of deep excavation and their removal after
measurements.
(e) Precautionary measures to be adopted in blasting as per IS 4081-1967 "Safety code of
blasting" (as amended from time to time) and storing explosives as per "Explosive Rules
1940" corrected uptodate.
3.12. Antiquities.- Any ancient carvings, relics of antiquity, coins or other curiosities
which may be discovered or excavated are the property of the Government and are to be
delivered to the Engineer-in-Charge.
3.13. Any vegetation, earth, moorum, sand, gravel, debris, brickwork, concrete, masonry
etc. obtained form excavation shall form the property of the Government.
3.14.Removal of earth deposits from the bed of new channels- Removal of the earth/soil
deposited, including due to slips etc. in the bed of channel could be paid as per item no
0301, only when the estimate for its removal has been prepared on the basis of cross
sections, longitudinal section plotted on graph measurement book (s), duly compared with
the Completed/ executed/designed sectioned and later sectioned by the Competent
Authority. Such work could than be executed through contract " Agency on form A or
form B "
0301 Earth work in bulk excavation (exceeding 30cm in depth, 1.5m in width as
well as 10sqm on plan) including disposal of excavated soil lead upto 50m
and lift upto 1.5m, disposed soil to be levelled and neatly dressed.
(a) Loose or soft soil cum 103.7
(b) Dense or hard soil cum 134.1
(c) Hard moorum cum 177.8
0302 Earth work in bulk excavation (exceeding 30cm in depth, 1.5m in width as
well as 10sqm on plan) including disposal or stacking of excavated soil
lead upto 50m lift upto 1.5m
(a) Disintegrated or soft rock (not requiring blasting) cum 413.5
(b) Hard rock requiring blasting cum 497.8
(c) Hard rock requiring chiselling (where blasting is prohibited) cum 881.9
0304 Earth work in rough excavation, filling excavated earth into depressions
on banking as directed, top surface to be levelled and neatly dressed.
(a) Loose or soft soil cum 115.2
(b) Dense or hard soil cum 148.1
(c) Hard moorum cum 166.4
0307 Earth work in excavation in trenches for foundations and for pipes, cables
etc. not exceeding 1.5m in width and for shafts, cesspits and the like not
exceeding 10sqm on plan including dressing of sides and ramming of
bottoms lift upto 1.5m including getting out the excavated soil and
disposal of surplus excavated soil as directed, within a lead of 50m
(a) Loose or soft soil cum 111.7
(b) Dense or hard soil cum 145.8
(c) Hard moorum cum 191.2
0308 Excavation in trenches for foundations and for pipes, cables, etc. not
exceeding 1.5m in width and for shafts, cesspits and the like not exceeding
10 sqm on plan including dressing of sides and ramming of bottoms, lift
upto 1.5m including getting out and stacking the excavated soil and
disposal of surplus excavated soil as directed within a lead of 50m
(a) Disintegrated or soft rock (not requiring blasting) cum 457.7
(b) Hard rock requiring blasting cum 615.2
(c) Hard rock requiring chiselling (i.e. hard rock requiring blasting but cum 909.5
where blasting is prohibited)
0309 Extra rates for quantities of work executed. In or under water or in foul cum 20% of
condition (extra rate for the main item concerned is allowed on account of respective item
slow progress of works)
0310 Excavating post holes (or similar holes) upto 0.5cum including getting out
the excavated soil, than returning the soil as required in layers not
exceeding 20cm in depth, including consolidating each deposited layer by
ramming, watering etc., disposing of surplus excavated soil as directed
within a lead of 50m and making good the surface.
(a) Loose or soft soil nos. 104.7
(b) Dense or hard soil nos. 135.5
(c) Disintegrated or soft rock (not requiring blasting) nos. 273.5
0311 Boring holes 3.5m deep in ordinary soil (for cast in situ piles) and getting
out the soil (under ramming if any shall be paid for separately) and
disposal of the surplus excavated soil as directed within a lead of 50m
for-Diameter of piles.
(a) 200 mm nos. 612.8
(b) 250 mm nos. 733.4
(c) 300 mm nos. 857.3
0312 Extra for under-ramming inside the bore holes for under reamed piles.
0312 Extra for under-ramming inside the bore holes for under reamed piles.
0313 Add to or deduct from the rate for bore holes of 3.5metre depths, if the
bore-holes are made deeper or shallower than 3.5metres.
(a) 200mm RM 195.6
(b) 250mm RM 260.8
(c) 300mm RM 291.8
0317 Dag-beling
0318 Extra for every additional Lead beyond 50metres or part thereof upto 200 cum 45.2
m for every 50 m lead
0319 Pumping out water caused by springs tidal or river seepage, broken water kl. 70.4
mains or drains or well point pumping and the like.
0320 Deduct from item no.0301, 0303, 0304, 0307 & 0308 If dressing either cum 10 % extra of
not done or not done as per specification respective item
0321 Dry silt clearance in drainage and culvert etc. cum 74.0
0323 Construction of embankment/sub grade by fly ash including clearing & cum 74.0
grabbing existing surface, (as per clause 305 and its sub clauses where
required and as per IRC SP-58-2001) i/c all lifts, cost of spreading,
watering, compaction and maintenance of surface during construction to
ensure shedding and preventing ponding of water, providing camber,
shaping and dressing, finishing etc. complete. (lead for fly ash will be paid
extra excluding loading)
4.2 Rates do not include centring, shuttering or form work unless otherwise specified.
4.4 Form work of RCC will be provided by the contractor and shall be removed by him.
No lead and lift of form work will be payable.
4.5 For RCC work the rates includes all finishing on all exposed surface, projections etc. as
per design. The resulting surface should be smooth and plain. Bottom faces of RCC slabs,
lintels and chajjas etc. shall be finished with suitable thickness of 1:3 cement mortar to
make surface smooth and even, where ever required. Ceiling plaster shall not be paid
separately in any case.
4.6 The rate includes for centring for providing fan hooks etc. For drip course where ever
required the seperate rates will be paid.
4.7 For plum concrete the plum used shall be of 150 mm maximum size rubble.
4.8 For fine and coarse aggregates IS 383 - 1970 may be referred, for plain and reinforced
concrete IS 456 - 2000 may be referred.
4.9 No seperate payment for lead and lift shall be permissible unless otherwise specified.
4.10 The proportion of various size of coarse aggregates in concrete is detailed below.
(This quantities are for 1 cum of concrete)
………………………………………………………………………………………
Concrete Max size of Metal or single Size and qty Total
Mix. Graded metal in cum.
………………………………….
40 mm 20 mm 10 mm
………………………………………………………………………………………
C.C. 1:2:4 20 mm - 0.67 cum 0.22 cum. 0.89cum
4.11 Items of R.C.C. includes formworks, centering, shuttering, proping, finishing and
curing etc.
4.12 Rates of centering and shuttering should be paid only for the item in which rates
excluding cost of formwork is mentioned.
4.13 Execution of R.C.C. work shall not be permitted without mixer and vibrator.
Code Description Unit Rate (Rs.)
0401 Filling available excavated earth (excluding rock) in trenches, plinth, sides cum 74.0
of foundation etc. in layers not exceeding 20cm in depth consolidating
each deposited layers by ramming and watering lead upto 50m and lift
upto 1.5m
0402 Filling foundation, around masonry work, plinth, sides of foundation etc. cum 257.1
with moorum I/c ramming layers not exceeding 20cm in depth
consolidating each deposited layers by ramming and watering lead upto
50m and lift upto 1.5m.
0403 Labour only for item no.0402 cum 74.0
0404 Filling in plinth with sand under floors including watering, ramming, cum 284.3
consolidating and dressing complete.
0405 Labour only for item no. 0404 cum 61.5
0408 Providing and laying in foundation, plinth and under floors lime concrete
with 40mm nominal size graded stone aggregates (metal) and 40% lime
mortar. i/c ramming in layers and curing complete excluding cost of form
work.
(a) Lime mortar 1:2 (1lime putty, 2sand) cum 2006.8
(b) Lime mortar 1:3 (1lime putty, 3sand) cum 1942.5
(c) Lime mortar 1:1:1 (1lime putty, 1surkhi, 1sand) cum 1959.8
(d) Lime mortar 1:2 (1lime putty, 2surkhi) cum 1912.8
0409 Labour only for item no. 0408 (for any proportion of lime mortar used) cum 938.7
0410 Deduct from item No. 0408 if shingles (pebbles) are used in place of cum 302.9
40mm nominal metal.
0411 Providing and laying on terrace upto floor two level lime concrete with cum 1735.8
graded brick aggregate 25mm nominal size and 50% mortar comprising of
1 lime putty and 2 surkhi and curing etc. complete.
0412 Labour only for item no. 0411. cum 850.4
0413 Providing and laying in foundation, plinth and under floors cement
concrete with 40mm nominal size graded stone aggregates (metal) i/c
ramming in layers and curing complete excluding cost of form work
(a) C.C. 1:2:4 (1cement, 2sand, 4metal) cum 2895.3
(b) C.C. 1:3:6 (1cement, 3sand, 6metal) cum 2401.8
(c) C.C. 1:4:8 (1cement, 4sand, 8metal) cum 2062.6
(d) C.C. 1:5:10 (1 cement, 5sand, 10metal) cum 1877.2
0413 Providing and laying in foundation, plinth and under floors cement
concrete with 40mm nominal size graded stone aggregates (metal) i/c
ramming in layers and curing complete excluding cost of form work
(e) C.C. 1:6:12 (1 cement, 6sand, 12metal) cum 1784.5
(f) C.C 1:2.5:5 ( 1cement, 2.5 sand, 5metal) cum 2665.9
0414 Labour only for item no. 0413 (for any proportion of cement concrete) cum 732.3
0415 Add to item No. 0413 for concrete work in super structure upto floor two cum 15 % of item
level for wall independent pillars and like. no. 0414 for
each floor
0416 Add to item No. 0413 and 0415 if in place of 40mm metal.
0417 Extra rate for providing and fixing in position upto floor two level, units cum 1937.6
of precast C.C. work of any mix fixing in cement mortar 1:2 and finishing
with cement plaster 6mm thick in cement mortar 1:3 including scaffolding
.
0418 Extra rate for laying cement concrete in or under water or liquid mud cum 103.6
including cost of pumping and bailing out and removing slush etc.
complete.
0419 Extra rate for providing and mixing water proofing material in cement Bag 39.3
concrete work in the proportions recommended by the manufacturers.
0420 Providing and laying damp proof course 50mm thick with C.C.1:2:4 with sqm. 220.4
20mm size graded stone aggregate. including curing.
0421 Applying one coat of hot bitumen (80/100) or equivalent using 1.7kg. Per sqm. 71.1
sqm On damp proof courses after cleaning the surface with brushes and
finally with a piece of cloth tightly soaked in kerosene oil.
0422 Plum cement concrete 1:2:4 with 75% graded metal of 40mm size and cum 2055.3
25% plums of 150mm size.
0423 Plum cement concrete 1:3:6 with 75% graded metal of 40mm size and cum 1866.6
25% plums of 150mm size.
0424 Plum cement concrete 1:4:8 with 75% graded metal of 40mm size and cum 1711.5
25% plums of 150mm size.
0425 Providing and placing in position RCC for roof, beams, columns column
footing lintels chhajjas, balcony, stairs etc, excluding cost of
reinforcement but including centring, shuttering, proping, finishing &
curing etc.complete.
(a) CC 1:1:2 (1 cement, 1 sand, 2 graded stone aggregate 20mm cum 5274.3
nominal size)
(b) CC 1:1.5:3 (1 cement, 1.5 sand, 3 graded stone aggregate 20mm cum 4593.4
nominal size)
(c) CC 1:2:4 (1 cement, 2 sand, 4 graded stone aggregate 20mm cum 4253.0
nominal size)
0426 Labour only for item 0425. cum 1023.1
0427 Add extra for labour only for additional floor or 6.m height and part cum 15 % of item
thereof PCC or RCC work in item no.0426 no. 0426 for
each floor
0428 Deleted …. ....
0434 Providing and laying five courses damp proofing treatment sumps, sqm. 441.8
reservoirs, roof etc. consisting of 1st. 3rd and 5th courses of blown type
petroleum bitumen of I. S. grade 85/25 applied @1.6kg/sqm and 2nd and
4th courses of self finished bitumen felt type 3 grade 2 (Hessian Base)
with priming coat of bituminous solution applied hot at the rate of
minimum of 0.25litre per sqm including preparation of surface by grouting
cracks, providing cement concrete fellets rounding of cerlers etc. wherever
required and cleaning and drying of surface before priming cost is applied,
complete as per direction of the engineers-in-charge.
0435 Providing and filling in position blown bitumen in expansion joints (10cm RM 7.9
deep and 1cm Wide)
0436 Deduct from item no 0413 if 63mm graded metal used in place of 40mm cum 37.2
metal
0437 False work for Arches up to 6meter span. sqm. 973.9
0501 Labour only for dressing stones hammer or rough dressed for C. R. cum 477.9
masonry work second sort.
0502 Random/ uncoursed rubble masonry in plinth and foundation, stones laid cum 1163.6
dry, well bounded, faced with selected stones and built with through
stones evenly placed at the rate of two per sqm
0503 Labour only for item no.0502 cum 566.2
0504 Random / uncoursed rubble masonry in plinth and foundation with mud cum 1497.6
mortar including levelling at plinth level.
0505 Labour only for item no 0504 cum 868.9
0507 Labour only for random/ uncoursed rubble masonry in any. Mortar for cum 953.5
item no.0506 excluding labour for preparation of mortar.
0508 Coursed rubble masonry second sort in plinth and foundation.
0509 Labour only for C.R. masonry in mortar of any ratio as in item no.0508 cum 1384.4
0510 Stone shelves fixed in walls in cement mortar 1:3 (1cement, 3sand) I/c
finishing complete.
(a) 30 mm thick sqm. 277.9
(b) 40 mm thick sqm. 287.7
(c) 50 mm thick sqm. 327.3
0512 Providing and fixing in cement mortar 1:6 (1cement, 6sand) flag stone
slab over drains.
(a) 30 mm thick sqm. 246.5
(b) 40 mm thick sqm. 256.3
(c) 50 mm thick sqm. 295.9
0514 Providing and fixing chhajja (sun shed) of stone 40mm thick and upto sqm. 433.3
80cm wide beyond the wall in cement mortar 1:4 I/c pointing in cement
mortar 1:2.
0515 Labour only for item no. 0514 sqm. 246.2
0516 Extra rate for C.R./ R.R./ U.C.R. stone masonry in super structure above cum 292.8
plinth level upto floor two level.
0517 Extra rate for laying stone work in or under water and or liquid mud cum 103.6
including cost of pumping or bailing out water and removing slush etc,
complete etc.(For every 0.3 meter depth)
0518 Providing and fixing fine dressed cut stone lintels of any size including cum 8415.2
setting in C.M. 1:2.
0519 Labour only for item no.0518 cum 4002.4
0520 Extra over item for additional lift for C.R. stone masonry work in super cum 1% rate of
structure above floor two level. stone masonary.
0601 Sun dried brick masonry in plinth and foundation in clay mortar. cum 1105.4
0603 Class 25 open bhatta or pajawa burnt brick masonry in plinth and cum 2512.1
foundation in clay mortar.
0604 Labour only for item no.0603 cum 706.9
0605 Class 25 open bhatta or pajawa burnt brick masonry in plinth and
foundation.
(a) Lime Mortar 1: 2(1lime, 2sand) cum 2938.7
(b) Lime mortar 1:3 (1lime putty, 3sand) cum 2904.9
(c) Lime surkhi mortar 1:1:1 (1lime, 1surkhi, 1sand) cum 2914.0
(d) Lime surkhi mortar 1:1:2 (1lime, 1surkhi, 2sand) cum 2886.5
(e) Cement lime mortar 1:1:6 (1cement, 1lime, 6sand) cum 3080.7
(f) Cement lime mortar 1:2:9 (1cement, 2lime, 9sand) cum 3023.6
(g) Cement mortar 1:3 (1cement, 3sand) cum 3253.9
(h) Cement mortar 1:4 (1cement, 4sand) cum 3123.6
(i) Cement mortar 1:5 (1cement, 5sand) cum 3053.4
(j) Cement mortar 1:6 (1cement, 6sand) cum 2993.3
(k) Cement mortar 1:8 (1cement, 8sand) cum 2913.1
0606 Add for masonry in supper structure above plinth level up to floor two cum 245.8
level
0607 Add extra for brick masonry in square or rectangular pillars. cum 261.4
0608 Add extra for brick masonry in circular pillars. cum 1055.4
0609 Add extra for brick masonry circular in plan, I/c wells to a mean radius not cum 357.8
exceeding 6m (Such as well stening and other similar type of works)
0610 Add for class 35 T.M. chimney kiln burnt brick in item no.0603 and 0605 cum 297.5
0611 Deduct for kumbhar brick class 20 burnt pajawa in item no. 0603 and cum 119.0
0605
0612 Labour only for brick masonry in plinth and foundation I/c making mortar cum 830.7
for item no.0605
0613 Labour only for brick masonry I/c scaffolding and making mortar in super cum 1087.9
structure for item no.0605
0614 Half brick masonry in class 25 open bhatta or pajawa burnt brick in super
structure including placing of 6mm iron bar at every 3rd layer of brick.
(a) In cement mortar 1:3 sqm. 432.9
(b) In cement mortar 1:4 sqm. 417.3
0615 Deduct for kumbhar brick class 20 burnt pajawa for item no. 0614 sqm. 12.6
0616 Add to item no.0614 for class 35 T.M. chimney burnt/ ghola bricks. sqm. 31.5
0618 Honey comb brick masonry with class 25 open bhatta or pajawa burnt
brick 10cm Thick.
(a) In cement mortar 1:3 sqm. 246.1
(b) In cement mortar 1:4 sqm. 228.9
0619 Deduct for kumbhar brick class 20 burnt pajawa for item no. 0618 sqm. 8.2
0620 Add to item no.0618 for class 35 T.M. chimney burnt/ ghola bricks. sqm. 20.6
0622 Class 25 open bhatta or pajawa burnt brick masonry in plain arches in cum 3620.6
superstructure span not exceeding 6 metres in cement mortar 1:3 (1
cement, 3 coarse and) excluding centring (height of prons not exceeding
3.5 metres) and shuttering complete.
0623 Labour only for arch masonry upto 6m span excluding centring but cum 1280.2
including labour for making mortar and curing.
0624 Add to item no.0605 and 0609 for well staining
0626 Add for Fly Ash brick in item no.0603 and 0605 cum -129.4
Thickness of panels
6. Panelled 25 mm 20 mm
7. Panelled 30 mm 25 mm
8. Panelled 35 mm 30 mm
9. Panelled 40 mm 30 mm
………………………………………………………………………………………
7.8. The guard bars for windows and ventilators shall be threaded at both the end and fixed
with nuts and suitable washers of MS plate of size 5cm x 5cm x 6mm thick.
7.9. The thickness of glass-pans should be 3mm or 7.5kg/Sqm unless otherwise stated for
wooden windows and ventilators.
7.10. In case of flush shutters 1.60mm tolerance will be allowed for finished sizes.
7.11. All joinery work should have bamboo nails and use of Fevicol etc. to have effective
joints necessary.
7.12. No chowkhat or shutter shall be painted before due inspection and approval by
Engineer-in-Charge.
7.13. Unless otherwise stated the gauge etc. of AC/ GI/ XPM Fly proof mesh shall be as
follows-
Plain AC sheet 5 mm thick
Plain GI sheet 22 gauge
XPM No. 19 3mm gauge x 20mm
Page 27 of 132
Fly proof mesh 22 gauge wire with 144 mesh/ sq. Inch.
7.14. Diameter of ballies should be measured at centre of ballies.
7.15. All portions of timbers like battens purlins, wall plates, door chowkhats etc. built into
or abutting the masonry or concrete should be given thick coat of hot Tar creosote or other
approved wood preservative.
7.16. All fixtures and fastenings shall be new sound and strong. They shall be sectional and
of the best quality. The size shape design and finish shall as per the sample approved by
the Executive Engineer. Number and size shall be as per standard specifications.
7.17. The following Indian Standards may be referred to -
IS CODE Title
204 Tower bolts
204 (Pt.i)1978 Ferrous metals (fourth revision)
204 (Pt.ii)1978 Non ferrous metals (fourth revision) (with amendment No.1)
205-1978 Non ferrous metal butt hinges (third revision)
206-1973 Tee and strap hinges (second revision)
207-1964 Gate and shutter hooks and eyes (revised) (reaffirmed 1977)
208-1979 Door handles (third revision)
281-1973 Mild steel sliding door bolts for use with padlock (second revision)
287-1973 Recommendation for maximum permissible moisture content for Timber
used for different purposes (second revision) (with amendment No.1)
303-1975 Plywood for general purposes (second revision) (with amendments no. 1
to 3)
362-1975 Parliament hinges (third revision)
363-1976 Hasps and staples (third revision)
364-1970 Fanlight catch (second revision)
401-1967 Code of practice for preservation of timber (second revision) ( with
amendment No.1)
419-1967 Putty, for use of windows frames (first revision)(with amendment
No.1)(reaffirmed 976)
451-1972 Technical supply conditions for wood screws (second revision)
452-1973 Door springs, rat-tail type (second revision)
453-1973 Double acting spring, hinges (second revision)
723-1972 Steel counter sunk head wire nails (second revision) (with amendments
No.1 to 3)
729-1979 Drawer locks, cupboard locks and box locks (third revision)
848-1974 Synthetic revise adhesive for plywood (phenolic and amino plastic) (first
revision)
1003 Timber panelled and glazed shutters.
1003(Pt.i)1977 Door shutter (second revision)
1003(Pt.ii)1966 Windows and ventilators shutters (first revision) (with amendments 1 to3)
1019-1974 Rim latches (second revision) (with amendment No.1)
1141-1973 Code of practice for seasoning of timber (first revision)
1328-1970 Veneered decorative plywood (first revision)
1341-1976 Steel butt hinges (third revision)
1378-1979 Oxidised copper finishes (second revision)
1658-1977 Fibre hard boards (second revision)
1659-1979 Block boards (second revision)
1868-1968 Anodic coatings on aluminium (first revision) (with amendment No.1)
2191Wooden flush door shutters (cellular and hollow core type)
2191(Pt.i)1980 Plywood face panels (third revision)
Page 28 of 132
2191(Pt.ii)1980 Particle board and hardboard face panels (second revision)
2202 Wooden flush door shutters (solid core type)
2202(Pt.i)1980 Plywood face panels (third revision)
2202(Pt.ii)1980 Particle board and hardboard face panels (second revision)
2209-1976 Mortise locks (Vertical type) (third revision) (with amendment No.1)
2380 Pt( i to xxi)1977 Methods of test for wood particle boards and boards from other
lignocellulosic materials (first revision) (with amendment No.1)
2681-1979 Non-ferrous metal sliding door bolts (Aldrops for the use
withpadlocks)(second revision)
2835-1975 Flat transparent sheet glass (second revision) (with amendment No.1)
3087-1965 Wood particle boards (medium density) for general purposes (with
amendmentNo.1).
3548-1966 Code of practice for glazing buildings
3564-1975 Door closers (hydraulically regulated) (second revision) (with amendment
No.1)
3618-1966 Phosphate treatment of iron and steel for protection against corrosion.
3813-1967 ' C' hooks for use with swivels.
3818-1971 Continuous (Piano) hinges (first revision) (with amendment No.1)
(reaffirmed 1978)
3847-1966 Mortise right latches (with amendments 1&2) (reaffirmed 1978)
4020-1967 Methods of tests for wooden flush doors. Type tests (with amendments
No.1 & 2)
4021-1976 Timber door, windows and ventilator frames (first revision).
4043-1969 Recommendations for symbolic designation of direction of closing and
faces of doors, windows and shutters.
4827-1968 Electroplated coatings of nickel and chromium on copper and copper
alloys (with amendments No.1&2)
4913-1968 Code of practice for selection installation and maintenance of timber
doors and windows.
4962-1968 Wooden side sliding doors.
4992-1975 Door handles for mortise locks (Vertical type) (first revision)
5187-1972 Flush bolts (first revision) (with amendment No.1) (reaffirmed 1978)
5437-1969 Wired and figured glass (reaffirmed 1976)
5930-1970 Mortise latch (vertical type) (with amendment No.1) (reaffirmed 1978)
6318-1971 Plastic windows stays and fasteners.
6607-1972 Rebated mortise locks (vertical type) (with amendment No.1)
(reaffirmed1978)
7196-1974 Hold fasts (with amendment No1)
7197-1974 Double action floor & springs (without oil check) for heavy doors.
8760-1978 Mortise sliding door locks with lever mechanism (with amendment No.1)
9460-1980 Flush drop handle for drawers.
Code Description Unit Rate (Rs.)
0701 Providing wood work in frames of doors, widows, clerestory widows and
other similar works brought framed and fixed in position.
(a) Bija wood cum 31879.2
(b) Sal wood cum 29117.5
(c) Other structural wood (seasond & chemicaly treated wood) cum 18070.4
0703 For architrave moulding, railings for stairs, cornices and moulded beading cum 50% extra of
etc. For any shape pattern or dealings add to item no.0702. respective item
0704 Providing wood work in trusses, purlins, rafters, posts, post plates, wall
plates and the like brought framed, hoisted and fixed in position.
(a) Bija wood cum 69107.4
(b) Sal wood cum 66366.4
(c) Other structural wood (seasond & chemicaly treated wood) cum 55402.4
0706 Providing wood work in frames of false ceiling, partitions, portions etc.
sawn and put-up in position.
(a) Bija wood cum 35352.8
(b) Sal wood cum 32521.4
(c) Other structural wood (seasond & chemicaly treated wood) cum 21196.0
0708 Extra for additional labour for curved works, such as in frames of curved cum 10 % extra of
fan lights. respective item
0709 Providing and fixing 30mm thick double leaf panelled, glazed or panelled
and glazed shutters for doors, windows and clerestory window including
black enamelled M.S. butt hinges with necessary screws.(half glazed and
half panelled)
(a) Second class Indian teak wood sqm. 2445.2
(b) Bija wood sqm. 1423.9
(c) Sal wood sqm. 1349.5
(d) Other structural wood (seasond & chemicaly treated wood) sqm. 1052.1
0710 Providing and fixing 25mm thick double leaf panelled, glazed or panelled
and glazed shutter for cupboards etc. including black enamelled M.S. butt
hinges with necessary screws.(half glazed and half panelled)
(a) Second class Indian teak wood sqm. 2179.8
(b) Bija wood sqm. 1276.6
(c) Sal wood sqm. 1213.0
(d) Other structural wood (seasond & chemicaly treated wood) sqm. 958.4
0712 Deduct from item no. 0710 for fully panelled shutters.
0712 Deduct from item no. 0710 for fully panelled shutters.
0713 Add to item no. 0709 & 0710 if 5mm thick glass is used. sqm. 7.3
0714 Providing and fixing 25mm thick single leaf battened and framed door
shutter including bright finished or/and black enamelled M.S. butt hinges
with necessary screws.
(a) Bija wood sqm. 1126.4
(b) Sal wood sqm. 1068.5
(c) Other structural wood (seasond & chemicaly treated wood) sqm. 836.9
0715 Providing and fixing 30mm thick single leaf battened and framed door
shutter including bright finished or/and black enamelled M.S. butt hinges
with necessary screws.
(a) Bija wood sqm. 1253.8
(b) Sal wood sqm. 1184.3
(c) Other structural wood (seasond & chemicaly treated wood) sqm. 906.4
0716 Providing and fixing 35mm thick single leaf battened and framed door
shutter including bright finished or/and black enamelled M.S. butt hinges
with necessary screws.
(a) Bija wood sqm. 1381.2
(b) Sal wood sqm. 1300.1
(c) Other structural wood (seasond & chemicaly treated wood) sqm. 975.9
0717 Providing and fixing 20mm thick single leaf battened door and window
shutters with necessary ledges and braces (25mm) including bright
finished or/and black enamelled M.S. butt hinges with necessary screws.
(a) Bija wood sqm. 1513.2
(b) Sal wood sqm. 1421.3
(c) Other structural wood (seasond & chemicaly treated wood) sqm. 1053.8
0718 Providing and fixing 25mm thick single leaf battened door and window
shutters with necessary ledges and braces (30mm) including bright
finished or/and black enamelled M.S. butt hinges with necessary screws.
(a) Bija wood sqm. 1754.8
(b) Sal wood sqm. 1641.0
(c) Other structural wood (seasond & chemicaly treated wood) sqm. 1185.6
0719 Providing and fixing 30mm thick single leaf battened door and window
shutters with necessary ledges and braces (35mm) including bright
finished or/and black enamelled M.S. butt hinges with necessary screws.
(a) Bija wood sqm. 1994.9
(b) Sal wood sqm. 1859.2
(c) Other structural wood (seasond & chemicaly treated wood) sqm. 1316.6
0720 Providing and fixing flush door shutters, solid core construction,
decorative type with skins of decorative veneered particle boards and
block board core, with frame of first class hard wood with particle board
veneered particle board face panels including black enamelled M.S. butt
hinges with necessary screws.
(a) 40 mm thick (double leaf) sqm. 1791.1
(b) 30 mm thick (double leaf) sqm. 1565.2
(c) 25 mm thick (double leaf) sqm. 1371.4
0721 Providing and fixing flush door shutters, solid core construction,
Non-decorative type (paintable) with skins of particle boards unveneered
and block board core, with frame of first class hard wood with particle
board veneered particle board face panels including black enamelled M.S.
butt hinges with necessary screws.
(a) 40 mm thick (double leaf) sqm. 1346.3
(b) 30 mm thick (double leaf) sqm. 967.0
(c) 25 mm thick (double leaf) sqm. 904.8
0722 Providing and fixing flush door shutters, solid core construction,
Non-decorative type (paintable) with skins of particle boards veneered
with commercial veneers and block board core, with frame of first class
hard wood with particle board veneered particle board face panels
including black enamelled M.S. butt hinges with necessary screws.
(a) 40 mm thick (double leaf) sqm. 1303.6
(b) 30 mm thick (double leaf) sqm. 1149.2
(c) 25 mm thick (double leaf) sqm. 1096.7
0723 Providing and fixing flush door shutters, hollow core construction,
decorative type with skins of decorative veneered particle boards with
frame of first class hard wood, with particle board or veneered particle
board face panels including black enamelled M.S. butt hinges with
necessary screws.
(a) 40 mm thick (double leaf) sqm. 1478.0
(b) 30 mm thick (double leaf) sqm. 1347.2
(c) 25 mm thick (double leaf) sqm. 1252.8
0724 Providing and fixing flush door shutters, hollow core construction,
Non-decorative type (paintable) with skins of particle boards, unveneered
with frame of first class hard wood, with particle board or veneered
particle board face panels including black enamelled M.S. butt hinges with
necessary screws.
(a) 40 mm thick (double leaf) sqm. 1242.6
(b) 30 mm thick (double leaf) sqm. 1111.7
(c) 25 mm thick (double leaf) sqm. 947.5
0725 Providing and fixing flush door shutters, hollow core construction,
Non-decorative type (paintable) with skins of particle boards veneered
with commercial veneers, with frame of first class hard wood, with
particle board or veneered particle board face panels including black
enamelled M.S. butt hinges with necessary screws.
(a) 40 mm thick (double leaf) sqm. 1129.2
(b) 30 mm thick (double leaf) sqm. 911.1
0725 Providing and fixing flush door shutters, hollow core construction,
Non-decorative type (paintable) with skins of particle boards veneered
with commercial veneers, with frame of first class hard wood, with
particle board or veneered particle board face panels including black
enamelled M.S. butt hinges with necessary screws.
(c) 25 mm thick (double leaf) sqm. 773.1
0726 Extra for using bright finished M.S. piano hinges instead of anodised
aluminium butt hinges in flush door shutters.
(a) Nickel plated M.S piano hinges sqm. 183.4
(b) Brass plated M.S piano hinges sqm. 102.6
0727 Deduct Iron butt hinges with necessary screws are supplied by the sqm. 28.0
department free of cost for flush door shutter.
0728 Add extra for double leaf shutter cum 10 % extra of
respective item
0729 Providing and fixing 30mm thick wire gauze shutters using galvanised
wire gauze of I.S. gauze designation 85G with wire of dia. 0.56mm for
doors, windows and clerestory window including bright finished or/ and
black enamelled M.S. butt hinges with necessary screws.
(a) Bija wood sqm. 920.5
(b) Sal wood sqm. 865.6
(c) Other structural wood (seasond & chemicaly treated wood) sqm. 646.0
0730 Providing and fixing plain trellis work of 40X12mm Laths placed 40mm
apart (frames to be paid separately) including fixing 50X12mm beading
complete with
(a) Bija wood sqm. 885.9
(b) Sal wood sqm. 840.6
(c) Other structural wood (seasond & chemicaly treated wood) sqm. 659.3
0732 Providing and fixing plain trellis work of half rounded (split) bamboos sqm. 559.0
40mm dia. placed at 40mm apart (frames to be paid separately) including
fixing 40mm dia. beading of half round bamboos.
0733 Labour only for item no.0732 sqm. 246.9
0734 Providing and fixing expanded metal 20x60mm strands 3.25mm wide and sqm. 409.3
1.6mm thick for windows etc. including 60X20mm beading of sal wood.
0735 Providing and fixing fly proof galvanised M.S. wire gauze of I.S. gauze sqm. 308.4
designation 85G with wire of dia. 0.56mm to windows and clerestory
window including 60X20mm beading of sal wood.
0736 Providing and fixing hard brown steel wire fabric 75x25mm mesh of sqm. 494.1
weight not less then 7.75kg. per sqm to window frames etc. including
60X20mm beading of sal wood.
0737 Providing and fixing Sal ballies in posts purlins, rafters, post plats etc.
including cost of iron nails and spikes required and applying wood
preservative on all unexposed surface.
(a) 80 mm diameter RM 33.8
(b) 100 mm diameter RM 51.2
(c) 125 mm diameter RM 59.7
0737 Providing and fixing Sal ballies in posts purlins, rafters, post plats etc.
including cost of iron nails and spikes required and applying wood
preservative on all unexposed surface.
(d) 150 mm diameter RM 69.2
0801 Providing and fixing plain Asbestos cement sheet ceiling with butt jointing sqm. 258.9
and wood screws (frame work and cover fillets to be measured and paid
separately) B class 5mm Thick A.C. sheet.
0802 Labour only for item No. 0801. sqm. 58.0
0803 Providing and fixing hessian cloth ceiling with nails (frame work and sqm. 67.1
cover fillets to be measured and paid separately)
0804 Labour only for item no. 0803. sqm. 38.3
0805 Providing and fixing fiber hard board sheet, lining with but jointing and
nails (frame work and cover fillets to be measured and paid separately) .
(a) Deleted ....
(b) Normal hard boards 5 mm thick sqm. 94.1
(c) Normal hard boards 6 mm thick sqm. 103.5
0807 Providing and fixing 12mm thick decorated type veneered particle board sqm. 265.3
lining with but jointing and nails (frame work and cover fillets to be
measured and paid separately) .
0808 Labour only for item no. 0807 sqm. 35.2
0809 Providing 10mm thick plaster of Paris (Gypsum anthydrous) ceiling up to sqm. 788.0
a height of 5 metres above floor level over Bija wood strips 25 X 6mm
with 10mm gap in between and rein forced with rabbit wire mesh fixed to
wooden frame(frame work and cover fillets to be measured and paid
separately) .
0810 Labour only for item no. 0809 sqm. 312.6
0901 Steel work in single section including in cutting, hoisting fixing in position kg. 43.1
in R.S. joists, channels, angles, tee.
0902 Steel work welded in built up sections, framed work, including cutting kg. 66.9
hoisting fixing in position in gratings, frames, guard bars, ladders, railing,
brackets and similar works & trusses and trussed purlins up to 25m span
and 15 m over all height
0903 Steel work in built up tubular trusses including cutting, hoisting, fixing in kg. 58.9
position, welded and bolted including special shaped washers etc.
complete of Mild steel tubes, electric resistant or induction butt welded
0904 Providing and placing in position tested steel for R.C.C. work including
cutting, bending, binding etc. as per drawings and placing in position
complete up to floor two level including cost of binding wire and all
wastage etc. complete.
(a) Mild steel and Medium tensile steel bars kg. 51.0
(b) Cold twisted / Hot rolled deformed / Thermo mechanicaly treated kg. 52.3
steel bars
0905 Deleted ---- ----
0907 Providing hard drown steel for R.C.C. work upto floor two level. kg. 44.2
0909 Providing and fixing in position collapsible steel shutters with vertical sqm. 4092.4
channels 20mm x 10mm x 2mm braced with flat iron diagonals 20mm x
5mm size with top and bottom rails of T-iron 40mm x40mm x6mm with
38mm dia steel pulleys complete with bolts and nuts, locking
arrangements, stoppers, handles.
0910 Labour only for item no.0909 for fixing only sqm. 149.6
0911 Providing and fixing rolling shutters of approved make, made of 80mm
wide M.S. Leith interlocked together through their entire length and
jointed together at the ends by end locks mounted on specially designed
pipe shaft, with brackets plates guide channels and locking with push pull
operation complete including the cost of hood over and spring.
(a) 80 x 1.25mm M.S. laths with 1.25mm thick top cover sqm. 1133.6
(b) 80 x 1.20mm M.S. laths with 1.20mm thick top cover sqm. 995.2
(c) 80 x 0.90mm M.S. laths with 0.90mm thick top cover sqm. 939.3
0912 Labour only for item no.0911 for fixing only sqm. 154.3
0913 Providing and fixing 27.5cm long wire spring grade No.2 approved make nos. 222.9
for rolling shutters.
0914 Providing and fixing hood cover for rolling shutters.
0915 Providing and fixing ball bearings of approved make for rolling shutters RM 204.7
exceeding 8.00 sqm area.
0916 Fixing standard steel doors, windows and ventilators in walls with 16 x sqm. 154.3
3.15mm to 10cm long embedded in cement concrete block 15 x 10cm
x10cm size, of 1:3:6 (1cement, 3coarse sand, 6stone aggregate 20mm
nominal size) or with wooden plugs and screws or rawl plugs & screws or
with fixing clips or worth bolts and nuts as required, (only steel doors/
windows/ ventilators shall be supplied for fixing free of cost at site of
work or cost of supply of one or more of these material (s) shall be paid
under separate items (s)
0917 Providing and fixing steel glazed doors, windows and ventilator of
standard Rolled steel sections without horizontal glazing bars, joints
mitred and welded with 16X3.15mm lugs 10cm long, embedded in cement
concrete block 1:3:6 cement concrete with 20mm graded metal of nominal
size or with wooden plugs and screws or rawl plugs and screws or with
fixing clips or with bolts and nuts including providing and fixing of
projecting hinges, handles, peg-stys, bolting devise, locking arrangements,
spring catch etc. as required complete and Providing and fixing of 5mm
thick glass panes with steel glazing clips special metal sash putty of
approved make I/c applying a priming coat of steel primer red oxide zinc
chromite etc. complete.
(a) Steel doors, windows side hung & ventilator top/ central hung. sqm. 1272.4
(b) Steel doors, windows & ventilator fixed sqm. 916.6
0918 Providing and fixing pressed steel door frames manufactured from
commercial mild steel sheet of 1.25mm thickness including hinges jamb,
lock jamb, bead and if required angle threshold of mild steel angle of
section 50 X 25mm, or base ties of 1.25mm pressed mild steel welded or
rigidly fixed together by mechanical means, adjustable lugs with split end
tail to each jamb including steel butt hinges 2.5mm thick with mortar
guards, lock strike- plate and shock absorbers as specified as directed by
Engineer-in -charge.
(a) Profile A (single rabate 80mm X 50mm size) RM 221.7
(b) Profile B (single rabate 100mm X 50mm size) RM 249.3
(c) Profile C (double rabate 115mm X 50mm size) RM 263.1
0919 Providing and fixing in position door shutters made up of cold rolled
framed profiles of pressed steel made from commercial M.S. sheet I/c
buzzers(shock absorbers) lock, 30cm Long strike plate and necessary
tower bolts, aldrop 300x16mm Etc. complete, painted with red oxide
primer paint manufactured by standard make.
(a) Single panel shutter type-A (Made of 1.00mm C.R. sheet) sqm. 949.9
(b) Single panel shutter type-B (Made of 0.8mm C.R. sheet) sqm. 863.5
(c) Double panel shutter type-A (Made of 1.00mm C.R. sheet) sqm. 1165.7
(d) Double panel shutter type-B (Made of 0.8mm C.R. sheet) sqm. 1079.4
0920 Providing and fixing M.S. round or square bars at required spacing in kg. 60.1
wooden frames of windows and clear-story windows including standard
threads at the ends of M.S. round window bars I/c cost of standard
hexagonal nuts and washers at both ends.
0921 Providing and fixing M.S. round or square bars with M.S. flats at required kg. 54.2
spacing in wooden frames of windows and clerestory windows.
0922 Providing and fixing M.S. grills of required pattern to wooden frames of kg. 89.6
windows etc. with M.S. flats at required spacing and frame around, round
or square bars with round headed bolts and nuts or by screws.
0923 Providing and fixing M.S. round holding down or anchor bolts with nuts kg. 45.7
and washer plates complete.
0924 Providing and fixing M.S. fan clamp type I of 16mm dia. M.S. bar bent to Each 95.0
shape with hooked ends in RCC slabs during laying including painting the
exposed portion of loops all as per standard design complete.
0925 Providing and fixing turn buckets and straining bolts for barbed wire Each 106.6
fencing.
0926 Providing and fixing fencing consisting 5 horizontal and 2 diagonals rows RM 257.2
of G.I Barbed Wire(minimum weight 9.38 Kg/100mt. As per IS 278:1962
Type 1), M.S. angle iron post 50x50x6mm (confirming to I.S. 225) 1.50
metre height above ground level and 0.30 m below ground level, c/c
spacing of each post shall not exceed 2.25 m with diagonal strut to hold
the fencing in line & level. Angle of size 50x50x6mm, length 1.00 m at
every fourth post fixed with nuts, bolts I/c applying a priming coat of steel
primer & painting with black paint to posts & struts etc. complete
including securing and screwing with G.I. tying wire, G.I. Staples, G.I.
U-Nails or steel pins etc. complete with cost of excavation & filling
cement concrete M-15 grade for fixing posts & struts to the pit of size
0.30x0.30x0.30 M for each post and struts etc. complete.
0927 Deduct in item No. 0926 if
0929 Labour only for fixing of R.C.C. posts, Angle iron posts or wooden ballies Each 63.5
of any size I/c excavation of pit 30x30x30cm And cost of concrete 1:3:6
with 40mm metal excluding cost of posts.
0930 Providing and fixing barbed wire fencing with 5 rows of horizontal barbed RM 199.0
wire and 2 digonal rows tightened to RCC post as per IS:4996-1984, 2M
long, 1.4 m above and 0.6 m belowe ground level, c/c spacing of each post
shall not exceed 3M with diagonal strut at every 30M to hold the fencing
in line and level. Top and bottom section of RCC post shall be 100mm X
100mm and 150mm X 150mm respectively, with iron pins casted in post.
The weight of two ply GI barbed wire shall not be less than 9.38 kg per
100 m lenght of wire. The RCC post shall be casted in M-20 cement
concrete as per IS:456-2000, with reinforcement as per IS:432-1982,
10mm dia 4 nos longitudinal bars and 6mm dia stirrups @ 150mm c/c,
complete with cost of excavation & filling cement concrete M-15 grade
for fixing posts & struts to the pit of size 0.30x0.30x0.60 M for each post
and struts etc. complete.
0931 Providing and fixing barbed wire fencing with 5 rows of horizontal barbed RM 154.6
wire and 2 digonal rows tightened to RCC post as per IS:4996-1984,
1.85M long, 1.25 m above and 0.6 m belowe ground level, c/c spacing of
each post shall not exceed 3M with diagonal strut at every 30M to hold the
fencing in line and level. Top and bottom section of RCC post shall be
85mm X 85mm and 125mm X 125mm respectively, with iron pins casted
in post. The weight of two ply GI barbed wire shall not be less than 9.38
kg per 100 m lenght of wire. The RCC post shall be casted in M-20
cement concrete as per IS:456-2000, with reinforcement as per
IS:432-1982, 6mm dia 4 nos longitudinal bars and 3.15mm dia stirrups @
100mm c/c, complete with cost of excavation & filling cement concrete
M-15 grade for fixing posts & struts to the pit of size 0.30x0.30x0.60 M
for each post and struts etc. complete.
0932 Providing & fixing of stop dam Kari shutters each of 40 to 60 cm height kg. 57.0
and width as per size of opening of stop dam, according to specific
requirement of engineer in charge (for height & width of shutter). Kari
shutters shall be fabricated with 3mm thick MS sheet on frame of MS
angle 35x35x5mm size with two diagonal stiffeners of MS angle
35x35x5mm. For shutter having width more than 1.00m, one extra
horizontal stiffener of MS angle size 35x35x5mm shall be provided at
center, including priming coat on shutter complete. The rate of shutter
includes filling the space between Kari shutter by B.C. soil with watering
and ramming.
(a) Lime surkhi mortar 1:1:1 (1lime, 1surkhi, 1sand) sqm. 117.6
(b) Lime surkhi mortar1:1:2 (1 lime, 1surkhi, 2 sand) sqm. 115.4
(c) Lime surkhi mortar 1:2 (1lilme, 2surkhi) sqm. 115.7
(d) Lime mortar 1:2 (1 lime, 2 sand) sqm. 119.6
1004 Labour only for 15mm thick lime surkhi and lime plaster of any ratio. sqm. 83.9
1006 Labour only for 10mm thick cement plaster of any ratio. sqm. 68.1
1008 Labour only for 15mm thick cement plaster of any ratio. sqm. 85.9
1013 Rough cast plaster using ordinary cement with a mixture of sand and sqm. 247.3
gravel or crushed stone graded from 2.36mm to 12.5mm nominal size
dashed over and including the fresh plaster in two layers. Under layer
12mm plaster 1:5 (1cement, 5sand) and top layer 10mm cement plaster
(1cement, 3sand)mixed with 10% fine grounded Hydrated lime by volume
of cement.
1014 Labour only for item no.1013 sqm. 174.2
1015 Extra rate for finishing with a floating cot of neat cement slurry over sqm. 36.8
cement plaster of any thickness.
1016 Extra rate for providing and mixing water proofing cement material in kg. 39.3
cement mortar for cement plaster in proportions recommended by
manufactures.
1017 Extra over items for plastering of circular walls not exceeding 6m in sqm. 13.3
radius
1018 Extra over plastering on ceiling and soffits of stairs upto floor two level sqm. 23.8
instead of plastering on wall.
1019 15mm thick water proofing mud plaster in tar coal, backing coat with sqm. 85.8
12mm thick mud mortar consisting of 70kg of chopped straw and 60kg of
bitumen coat with 3mm thick gobri leaping mixed with 100kg of bitumen
cut back per cum of soil on brick/stone masonry walls for interior
plastering upto floor two level I/c arisen, interval rounded angle not
exceeding 80mm in girth and finished even to smooth.
1020 Pointing on brick work with lime mortar 1:2 (1lime putty, 2sand)
1021 Pointing on brick work with cement mortar 1:3 (1cement, 3sand)
1022 Pointing on brick work with cement mortar 1:4 (1cement, 4sand)
1024 Pointing on flat brick flooring with cement mortar 1:3 (1cement, 3sand)
1025 Pointing on flat brick flooring with cement mortar 1:4 (1cement, 4sand)
1027 Pointing on brick on edge flooring with cement mortar 1:2 (1cement,
2sand)
(a) Flush pointing sqm. 109.8
(b) Ruled pointing sqm. 113.2
1028 Pointing on brick on edge flooring with cement mortar 1:3 (1cement,
3sand)
(a) Flush pointing sqm. 107.6
(b) Ruled pointing sqm. 110.9
1029 Pointing on brick on edge flooring with cement mortar 1:4 (1cement,
4sand)
(a) Flush pointing sqm. 105.7
(b) Ruled pointing sqm. 109.0
1031 Pointing on CR masonry with lime surkhi mortar 1:2 (1 lime putty, 2
surkhi)
(a) Flush pointing sqm. 107.9
(b) Ruled pointing sqm. 110.8
(c) Raised and cut pointing sqm. 159.4
1035 Pointing on random rubble masonry or uncoursed stone masonry with lime
surkhi mortar 1:2 (1lime putty, 2surhki)
(a) Flush pointing sqm. 124.6
(b) Ruled pointing sqm. 128.4
(c) Raised and cut pointing sqm. 195.6
1039 Pointing on stone slab ceiling with cement mortar 1:2 (1 cement, 2 sand)
1043 Extra over items pointing on walls for height more then 10m ground level sqm. 10.3
for every additional height of 5m or part there off.
1044 Providing throating or plaster drip and moulding to R.C.C. chhajja. RM 25.6
1045 15mm thick plain cement mortar bands upto 300mm in width with cement
mortar 1:4 (1 cement, 4sand)
(a) Flush band sqm. 23.6
1045 15mm thick plain cement mortar bands upto 300mm in width with cement
mortar 1:4 (1 cement, 4sand)
(b) Sunk band sqm. 25.6
(c) Raised band sqm. 28.9
1046 15mm thick plain cement mortar bands above 300mm in width with
cement mortar 1:4 (1cement, 4sand)
(a) Flush band sqm. 183.1
(b) Sunk band sqm. 203.0
(c) Raised band sqm. 236.3
1047 20mm thick plain cement mortar band upto 300mm in width with cement
mortar 1:4 (1cement, 4sand)
(a) Flush band RM 27.1
(b) Sunk band RM 29.1
(c) Raised band RM 32.4
1048 20mm thick plain cement mortar band above 300mm in width with cement
mortar 1:4 (1cement, 4sand)
(a) Flush band sqm. 216.1
(b) Sunk band sqm. 236.1
(c) Raised band sqm. 269.3
1101 Providing corrugated C.I. sheet of class III roofing fixed with galvanised
iron J or L hooks bolts and nuts 8mm diameter with bitumen and G.I.
limpet washers or with complete excluding the cost of purlins, rafters and
trusses.
(a) 0.63 mm thick sheet. sqm. 532.3
(b) 0.80 mm thick sheet. sqm. 640.7
1103 Providing ridges or hips 600mm over all in plain G.I. sheet class III fixed
with galvanised iron J or L hooks bolts and nuts 8mm diameter G.I. limpet
bitumen washers complete.
(a) 0.63 mm thick sheet. RM 404.5
(b) 0.80 mm thick sheet. RM 461.7
1104 Providing valleys 900mm over all in plain1.6mm thick G.I. sheet class III RM 873.3
fixed with galvanised iron J or L hooks bolts and nuts 8mm diameter G.I.
limpet bitumen washers complete.
1105 Labour only for item no.1103 and 1104 RM 161.2
1106 Providing 6mm thick corrugated asbestos cement sheets roofing fixed with sqm. 278.0
galvanised iron J or L hooks bolts and nuts 8mm dia. G.I. plain and
bitumen washer complete excluding the cost of purlines rafters and
trusses.
1107 Labour only for item no.1106 sqm. 56.7
1108 Providing and fixing ridges hips in asbestos cement sheet roofing with G.I.
J or L hooks bolts and nuts 8mm dia. G.I. plain and bitumen washer
complete .
(a) Close fitting adjustable ridge RM 324.8
(b) Unserrated adjustable hips. RM 268.5
1110 Tiled roofing with Mangalore tiles, including sal, bija, haldu or saj battens sqm. 273.2
of size 50mm X 25mm but excluding ridge and hip tiles.
1111 Labour only for item no.1110 sqm. 141.6
1112 Tiled roofing with Mangalore tiles, excluding hipes, ridges and battens sqm. 190.3
1114 Providing and fixing Manglore hipes and ridge tiles RM 127.7
1116 Providing and laying single Allahabad tiles without battens but including sqm. 252.0
hip and ridge tiles.
1117 Labour only for item no.1116 sqm. 105.6
1118 Providing and fixing Allahabad hipes and ridge tiles RM 77.3
1120 Providing stone slab roofing and laying in cement mortar 1:4 (1cement,
4sand) over R.S. joists or R.C.C. battens (R.S. joists and R.C.C. battens to
be paid separately) including pointing the exposed joints with the same
mortar complete.
(a) Red stone slab 40 mm thick. sqm. 291.0
(b) Red stone slab 50 mm thick. sqm. 339.2
1122 Lime concrete terracing on roofing's average thickness 100mm laid to fall sqm. 450.1
with 25mm nominal size brick ballast and 50% lime mortar 1:2 (1lime
putty, 2surkhi)(rammed and beaten with split bamboos and wooden the
thappies till the surface is hardened) and well finished with gur and
belwater treatment including rounding of junctions with parapets, curing
etc. complete.
1123 Labour only for item no.1122 sqm. 320.6
1124 Painting top of roofs with bitumen of approved quality 170kg/ 100sqm sqm. 378.2
impregnated with a coat of course sand at 0.60cum per 100sqm including
cleaning the slab surface with brushes and finally with a piece of cloth
lightly soaked in kerosene oil complete.
1125 Labour only for item no.1124 sqm. 18.1
(a) Lime concrete with 20 mm nominal size brick aggregate and 50% cum 4091.8
lime mortar 1:2 (1 lime putty, 2 surkhi)
(b) Cement mortar 1:3 cum 5741.3
(a) Lime concrete with 20 mm nominal size brick aggregate and 50% cum 3206.4
lime mortar 1:2 (1 lime putty, 2 surkhi)
(b) Cement mortar 1:3 cum 2702.9
1128 Providing and laying single country tiles (without battens) complete. sqm. 135.5
1130 Providing and laying single country tiles on split bamboo battens. sqm. 452.6
1132 Add for double country tilling in item no. 1128 & 1130 sqm. 135.5
1133 Add for labour double country tilling in item no. 1129 & 1131 sqm. 62.7
1134 Providing and laying single wheel tiling without battens sqm. 115.3
1136 Centering and shuttering for arch roof including all lead and lift. (for low sqm. 79.6
cost House)
1137 Providing and fixing of full round country tiles (Guna tiles) in position sqm. 467.8
including lock rail gap cover with cement mortar 1:3 with water proofing
compound and plaster with chicken mess curing etc. complete. (for low
cost House)
1138 Providing and fixing of broken ceremic tiles with neat cement, curing etc. sqm. 255.1
(for low cost House)
1139 Providing and fixing cut stone slab (chisel dressed) for roofs including cum 8327.8
flush pointing of the bottom in C.M. 1:3 (1cement, 3sand) and filling the
joints in C.M. 1:4 (1cement, 4sand) including fixing in chased grooves in
walls, curing etc. complete.
1140 Labour only for item 1139 cum 3733.4
1141 Providing & fixing of precoated galvanised iron profile sheets (size,shape sqm. 495.6
& pitch of corrugation as approved by engineer in charge) 0.5mm +/- 5%
total coated thickness(TCT) thick zinc coating 120 gsm as per IS:277 in
240mpa steel grade,5-7 microns appoxy primer on both side of the sheet
and polyester top coat 15-18 microns.Sheet should have protective guard
film of 25 microns min. to avoid scratches while transportation and should
be supplied in single length up to 12 mtr or as desired by
engineer-in-charge.The sheet shall be fixed using self drilling / self
tapping screws of size 5.5x55mm with EPDM seal or with polymer coated
J or L hooks,bolts and nuts 8mm dia. with bitumen and G.I. limpet
washers or with G.I. limpet washers filled with white lead complete upto
any pitch in horizontal/vertical or curved surfaces excluding the cost of
purlins, rafters and trusses and i/c cutting to size and shape wherever
required.
1142 Providing & fixing of precoated galvanised steel sheet roofing accessories RM 490.2
0.5mm +/- 5% total coated thickness(TCT) zinc coating 120 gsm as per
IS:277 in 240mpa steel grade,5-7 microns appoxy primer on both side of
the sheet and polyester top coat 15-18 microns. using self drilling / self
tapping screws of size 5.5x55mm with EPDM seal or with polymer coated
J or L hooks,bolts and nuts 8mm dia. and or G.I. seam bolts and nuts,G.I.
plain and bitumen washers complete.
Ridges plain (500 - 600mm)
1143 Providing & fixing of precoated galvanised steel sheet roofing accessories RM 661.7
0.5mm +/- 5% total coated thickness(TCT) zinc coating 120 gsm as per
IS:277 in 240mpa steel grade,5-7 microns appoxy primer on both side of
the sheet and polyester top coat 15-18 microns. using self drilling / self
tapping screws of size 5.5x55mm with EPDM seal or with polymer coated
J or L hooks,bolts and nuts 8mm dia. and or G.I. seam bolts and nuts,G.I.
plain and bitumen washers complete. Gutter ( 600mm
over all girth).
1203 25mm thick mud flooring smoothing and cow dung leeping sqm. 52.2
1204 Hammer dressed 15cm thick stone paving laid in camber with 20mm lime sqm. 541.9
mortar (1:2) bedding and cement pointing in cement mortar 1:3 for
roadways.
1205 Labour only for item no.1204 sqm. 363.7
1206 Hammer dressed 20cm thick stone paving laid in camber with 20mm lime sqm. 626.3
mortar (1:2) bedding and cement pointing in cement mortar 1:3 for
roadways.
1207 Labour only for item no.1206 sqm. 415.6
1208 Hammer dressed 26cm thick stone paving laid in camber with 20mm lime sqm. 782.0
mortar (1:2) bedding and cement pointing in cement mortar 1:3 for
roadways.
1209 Labour only for item no.1208 sqm. 519.5
1210 Rough chisel dressed sand stone flooring over 20mm average thick base of
cement mortar 1:5 (1cement, 5sand) with joints finished flush (Area of
each stone should not be less than 0.20 Sqm.)
(a) With 25 mm thick stone sqm. 358.6
(b) With 40 mm thick stone sqm. 378.3
1212 Fine dressed stone slab flooring over 20mm average thick base of cement
mortar 1:5 (1cement, 5sand) with joints finished flush.(Area of each stone
should not be less than 0.20 Sqm.)
(a) With 25 mm thick stone sqm. 898.0
(b) With 40 mm thick stone sqm. 917.8
1214 Fine dressed rubbed stone flooring over 20mm average thick base of
cement mortar (1:5) i/c pointing C.M. (1:2) with admixture of pigment to
mach the shade of stone. (Area of each stone should not be less than 0.20
Sqm.)
(a) With 25 mm thick stone sqm. 1197.2
(b) With 40 mm thick stone sqm. 1216.9
1216 Extra for nosing in steps and treads of rough dressed sand stone slab. RM 34.1
1217 Extra for nosing in steps in treads with fine dressed and rubbed sand stone RM 231.4
slab.
1218 40mm cement concrete flooring with 25mm under layer of cement sqm. 293.0
concrete 1:3:6 (1cement, 3sand, 6stone aggregate of size 12.5mm and
below) and 15mm wearing (1cement, 2 to 3 stone aggregate of size
4.75mm and below) laid in interval with base course and finished with a
floating coat of neat cement.
1219 Labour only for item no.1218 sqm. 195.7
1220 Cement concrete flooring 1:2:4 (1cement, 2sand, 4graded stone aggregate,
20mm nominal size) laid in one layer and finished with floating coat of
neat cement.
(a) 40 mm thick. sqm. 213.4
(b) Deleted ....
1222 Cement concrete pavement (25mm to 50mm thick) with 1:2:4 (1cement, cum 3343.7
2sand, 4graded stone aggregate 20mm nominal size) i/c finished with
floating coat of neat cement.
1223 Labour only for item no.1222 cum 886.6
1224 Extra for making cheques of approved pattern on cement concrete floors, sqm. 25.6
steps, landing, pavement etc.
1225 15mm cement plaster skirting upto 30cm height with cement mortar 1:3 (1 sqm. 207.9
cement, 3 sand) with a floating coat of neat cement i/c rounding of
junction with floor.
1226 40mm thick marble chip flooring rubbed and polished to granolithic
finish, under layer 32mm thick c.c. 1:2:4 with 10mm metal and top 8mm
thick with white black or white and black marble chip of nominal size laid
in cement marble powder mix 3:1 in proportion of 4:7 (4cement marble
powder mix, 7 marble chips by vol.)
(a) Dark shade pigment with ordinary cement (in top layer only). sqm. 675.9
(b) Light shade pigment with white cement (in top layer only). sqm. 677.6
1228 Extra rate for providing and fixing Aluminium strips 40mm wide 1.5mm RM 58.2
thick painted with protective coat of bitumen in joints of floors
1229 Extra for providing and fixing glass strips in joints of floors
1230 Extra rate for terrazzo flooring laid as floor borders, margins and similar sqm. 19.0
band exceeding 7.5cm but not exceeding 30cm in width.
1231 Extra rate for laying terrazzo flooring on staircase treads not exceeding sqm. 28.2
30cm in width. i/c cost of forming nose etc.
1232 Precast cement concrete tiles 20mm thick with aggregate of size upto 6mm
laid in floors, treads of steps and landing on 20mm thick bed of cement
mortar 1:6 (1cement, 6sand) jointed with neat cement slurry with pigment
to match the shade of the tiles complete with precast tiles.
(a) Light shades using white cement. sqm. 422.9
(b) Medium shades using approximately 50% white cement and 50% sqm. 397.3
ordinary cement.
(c) Dark shades using ordinary cement. sqm. 370.7
1234 Extra if precast cement concrete tiles are laid in treads of steps not sqm. 27.9
exceeding 30cm in width.
1235 Precast cement concrete tiles 20mm thick with aggregate of size upto 6mm
in skirting and rises of steps not exceeding 30cm in height on 12mm thick
cement plasters 1:3 (1cement, 3sand) jointed with neat cement slurry
complete with tiles.
(a) Light shades using white cement. sqm. 522.8
(b) Medium shades using approximately 50% white cement and 50% sqm. 640.8
ordinary cement.
(c) Dark shades using ordinary cement. sqm. 449.6
1237 Precast terrazzo tiles 20mm thick with white, black or white and black
marble chips of size upto 6mm laid in floors, treads of steps and landing
on a bed of 25mm average thickness and of lime mortar 1:1:1 (1lime
putty, 1surkhi, 1sand) jointed with neat cement slurry mixed with pigment
to match the shade of the tiles i/c rubbing and polishing complete with
precast titles.
1239 Extra if terrazzo tiles are laid in treads of steps not exceeding 30cm in sqm. 34.0
width.
1240 Precast terrazzo tiles 20mm thick marble chip of size upto 6mm skirting
and risers of steps not exceeding 30cm in height on 10mm thick cement
plaster 1:3 jointed with neat cement slurry i/c rubbing and polishing
complete with precast titles.
(a) Light shade using white cement. sqm. 813.9
(b) Medium shades using approximately 50% white cement and 50% sqm. 796.7
ordinary cement.
(c) Dark shades using ordinary cement. sqm. 716.6
1242 Chequered precast cement concrete tiles 22mm thick with aggregate of
size upto 6mm in floors, treads of steps and landing on 20mm thick bed of
cement mortar 1:6 (1cement, 6 sand) jointed with neat cement slurry with
pigment to match the shade of the tiles.
(a) Light shades using white cement. sqm. 568.0
(b) Medium shades using approximately 50% white cement and 50% sqm. 544.0
ordinary cement.
(c) Dark shades using ordinary cement. sqm. 515.8
1244 Extra rate rubbing and polishing C.C.. tiles in flooring skirting or dado. sqm. 156.8
1245 White glazed tiles 6mm thick in flooring, treads of steps and landings laid sqm. 895.2
on a bed of 12mm thick cement mortar 1:3 finished with flush pointing in
white cement.
1246 Labour only for item no.1245 sqm. 507.9
1247 Marble stone slab flooring over 20mm average thick base of C.M. 1:6
with grey cement including rubbing polishing etc. complete. (Area of each
stone should not be less than 0.20 Sqm.)
(a) Marble slab 25 mm thick. sqm. 1988.3
(b) Marble slab 30 mm thick. sqm. 2178.9
1249 25mm thick marble tiles in risers and treads of steps, skirting dado walls sqm. 2096.7
and pillar laid on 10mm thick base of C.M. 1:3 and jointed with grey
cement slurry including rubbing polishing etc. complete.
1250 Labour only for item no.1249 sqm. 1435.5
1251 Extra if pigment is used in the cement slurry to match the shade of the sqm. 3.7
marbel slabs.
1252 Add extra if white cement slurry is used instead of grey cement slurry in sqm. 6.8
joints of marbel stone flooring or tiles for all thickness
1254 Kota stone slab flooring over 20mm thick base of C.M. 1:6 laid over and
jointed with grey cement slurry mixed with pigment to match the shade of
slab including grinding, rubbing & polishing etc. complete. (Area of each
stone should not be less than 0.20 Sqm.)
(a) 25 mm thick. sqm. 1108.7
(b) 30 mm thick . sqm. 1270.1
(c) 40 mm thick. sqm. 1343.0
1256 Kota stone slab/Cuddapah stone slab 25mm thick in risers and treads of sqm. 1206.6
steps, skirting dado and pillar laid in 12mm thick C.M. 1:3 and jointed
with grey cement slurry mixed with pigment to match the shade of slab
including rubbing polishing etc. complete.
1257 Labour only for item no.1256 sqm. 905.6
1258 Linoleum covering to floors plain or curved laid with approved adhesive sqm. 414.1
on upper floor i/c stretching cutting and fitting complete 3.2mm thick
1259 Labour only for item no.1258 sqm. 33.2
1260 15mm cement concrete topping 1:2 to 3 (1cement, 2-3stone aggregate sqm. 135.3
4.75mm and below by volume) laid over and finished monolithic with
structural slab.
1261 Labour only for item no.1260 sqm. 81.2
1262 20mm cement concrete toping (1 cement, 2-3 stone aggregate 4.75mm and sqm. 164.3
below by volume) laid over and finished monolithic with base concrete.
1263 Labour only for item no. 1262 sqm. 93.5
1264 25mm cement concrete toping 1:2:4 (1cement, 2sand, 4graded stone sqm. 160.4
aggregate 12.5mm nominal size) finished with floating coat of neat cement
(base concrete to be paid separately)
1265 Labour only for item no.1264 sqm. 97.2
1266 Second class dry brick flooring i/c filling joints with fine sand. sqm. 280.5
1268 Second class brick flooring laid dry grouted with C.M. 1:6 i/c finishing the sqm. 311.6
joints flush.
1269 Labour only for item no.1268 sqm. 94.4
1270 22cm thick grouted stone pitching (without quarry spalls) with individual sqm. 600.1
stones of 22cm depth in minimum size 0.014cum grouting in cement
mortar 1:6
1271 Labour only for item no.1270 sqm. 298.0
1272 22cm thick dry stone pitching (without quarry spalls) with individual stone sqm. 278.5
of 22cm depth and minimum size 0.014
1273 Labour only for item no.1272 sqm. 185.0
1274 22cm thick dry stone picked up boulder pitching i/c picking of boulder sqm. 227.8
with individual size of 22cm depth.
1275 Add extra item no. 1274 for quarried boulder pitching. sqm. 180.0
1279 Hammer dressed 15cm thick stone paving laid in camber in sqm. 395.3
moorum bedding and filled with moorum mortar.
1280 Labour only for item no.1279 sqm. 311.7
1281 40 to 50mm thick flag stone flooring laid over 20mm thick cement mortar sqm. 384.3
(1:6) bedding I/n cement pointing in cement mortar 1:3
1282 Labour only for item no.1281 sqm. 187.9
1301 Removing old paint or polish from wood and wood based surfaces with sqm. 31.9
caustic soda solution and making the surface even.
1302 Removing old paint from steel and other metal surfaces and making the sqm. 59.9
surface even with hand seraping.
1303 Removing white wash or colour wash by steel wire brushing and/or sqm. 5.9
scraping; sand papering and preparing the wall surface smooth including
necessary repairs to scratches complete.
1304 Removing dry or oil bound distemper by washing and scraping and sand sqm. 13.2
papering the wall surface smooth including necessary repairs to scratches
complete.
1305 Washing and cleaning of decorated wall surfaces with soap, soda and sqm. 2.5
water.
1306 Extra over item 1305 for cleaning the old plastered ceiling and/or sloping sqm. 2.8
roofs with soap, soda and water.
1307 White washing whith lime on undecorated wall surfaces (3coats) to give sqm. 13.2
an even shade including thoroughly broomed the surface to remove all
dirt, dust, mortar drops and other foreign matter.
1308 White washing whith lime on undecorated wall surfaces (two coats) to sqm. 9.0
give an even shade including thoroughly broomed the surface to remove
all dirt, dust, mortar drops and other foreign matter.
1309 White washing with lime on decorated wall surfaces (one coat) to give an sqm. 4.2
even shade including thoroughly brooming the surface to remove all dirt,
dust, mortar drops and loose scales of lime wash and other foreign matter.
1310 Labour only for
1311 Colour washing 2 coats over and including a primary coat of white sqm. 16.2
washing on undecorated wall surface.
1312 Colour washing 1 coats on decorated wall surface. sqm. 5.3
1320 Distempering with dry distemper of approved brand and manufacture (two sqm. 49.3
coats) and of required shade on undecorated wall surfaces to give an even
shade, over and including priming coat of whiting after thoroughly
brushing the surface free from mortar dropping and other foreign matter
including preparing the surface even and sand papered smooth.
1321 Dry distemper of best quality of any shade 1 coat and old surface for sqm. 13.2
repairs etc.
1322 Labour only
1323 Oil bound distemper of approved quality of any shade two coats on new sqm. 74.2
works including priming coat.
1324 Oil bound distemper of best approved quality of any shade one coat on old sqm. 29.2
surface.
1325 Labour only for item no.1323 sqm. 57.3
1327 Wood oiling to new work with double boiled linseed oil two coats. sqm. 28.1
1328 Wood oiling to old work with double boiled linseed oil one coat. sqm. 20.0
1330 Varnishing two costs (excluding priming coat) on new wood and wood sqm. 82.6
based surfaces, under coating, with flatting varnish and finishing coat with
varnish to give an even surface including cleaning the surface of all dirt,
dust and sand papering so as to produce a smooth dry and matt surface.
1331 Varnishing one coat (excluding priming coat) on previoulsy varnished sqm. 37.2
wood and wood based surfaces to give an even surface including cleaning
the surface of all dirt, dust and sand papering so as to produce smooth, dry
and matt surface.
1335 Painting with enamel paint, brushing, interior to give an even shade I/n
cleaning the surface of all dirt dust and other foreign matter on steel and
other metal surfaces.
(a) 3 coats sqm. 98.7
(b) 2 coats sqm. 70.7
(c) 1 coats sqm. 35.9
1337 Painting two coat's (excluding priming coat) on new steel and other metal
surfaces with Aluminium paint, brushing to give an even shade including
cleaning the surface of all dirt, dust and other foreign matter.
(a) 2 coats sqm. 56.0
(b) 1 coats sqm. 33.4
1339 Spray painting 2 coats excluding priming coat on new steel and other sqm. 83.0
metal surface with enamel paint.
1340 Spray painting 1 coats excluding priming coat on new steel and other sqm. 52.7
metal surface with enamel paint.
1341 Labour only for
1342 Painting 1 coats excluding priming coat on previously painted steel and sqm. 45.0
other metal surface with enamel paint.
1343 Labour only for item no.1354 sqm. 26.1
1344 Coal tarring 2 coats on new wood and wood based surface . sqm. 24.8
1345 Coal tarring 1 coats on new wood and wood based surface. sqm. 14.2
1347 Polishing with French polish two coats on new wood and wood based sqm. 133.0
surfaces to give an even surface including cleaning the surface of all dirt,
dust and sand papered smooth and including a coat of wood filler.
1348 Polishing with French polish one coat on new wood and wood based sqm. 67.3
surfaces to give an even surface including cleaning the surface of all dirt,
dust and sand papered smooth and including a coat of wood filler.
1349 Labour only for
1350 Floor polishing on Masonry or Concrete floors with wax polish of sqm. 31.0
approved brand and manufacture.
1351 Deleted ---- ----
1401 Providing and fixing small pieces (not exceeding 150cucm) for making
good where hinges etc have been removed from frames or joinery, etc.
(a) Sal wood. Each 51.0
(b) Bija wood Each 55.0
1402 Renewing Bars, stiles on rails, straight for joinery upto 50mm thick
including meters, haunchings, mortises, etc. and removing old defective
pieces.
(a) Sal wood. RM 199.2
(b) Bija wood RM 212.7
1403 Rewedging cramping joinery of any description with new wedges in glue
or white lead and repining including rehanging or refixing of shutters,
hinges or pivots excluding removing or dismantling.
(a) Not exceeding 1sqm per leaf of soft wood Each 254.0
(b) Not exceeding 1 sqm. per leaf for hard wood Each 382.6
(c) Exceeding 1 sqm.but not exceeding 2 sqm.per leaf for soft wood Each 382.6
(d) Exceeding 1 sqm.but not exceeding 2 sqm.per leaf for hard wood Each 508.1
1404 Making repairs to joinery at angles with & including 300mm x 25mm x nos. 53.0
3mm length of M.S. flat forged to shape and let into wood work, counter
sunk, drilled and screwed.
1405 Renewing wooden battens in roofing including making good the holes in
walls including removal of rubbish to the demping ground with in a lead
of 50metres.
(a) Bija wood battens cum 32912.6
(b) Sal wood battens cum 30163.8
1406 Providing and fixing M.S. fan clamps of 16mm dia mild steel in existing Each 185.5
RCC slab including cutting chase and making good.
1407 Removal of old broken glass panes (any thickness or size quality or sqm. 103.8
description) from wood frames, glazed with putty or fixed with beads.
1408 Supplying and fixing new wooden beads(fillets) wherever necessary.
1410 Refixing old glass panes bedded in putty and fixed with glazing pins. sqm. 263.9
1411 Refixing old glass panes with old wooden beads (excluding cost of beads sqm. 219.8
1412 Renewing tiles in patches in areas exceeding 10 tiles and not exceeding 5
sqm including removing old tiles, preparing surfaces and laying or setting
new or old tiles complete.
(a) Glazed tiles sqm. 538.7
(b) Cement tiles or Terrazzo tiles sqm. 416.8
1413 Cutting out cracks of roof terrace to V-Section, cleaning out wetting, RM 41.5
grouting with cement and sand slurry 1:3 (1 cement, 3 sand)
1414 Cutting out cracked of roof terrace to V-Section, cleaning out and filling RM 57.0
solidly with a hot mixture of bitumen and clean dry sand slurry 1:1 (1 by
weight)
1415 Dubbing out on old irregular walls average 10mm thick with.
1416 Repairs to plaster in patches of 2.50 sqm and under and 10 to 15mm thick
including cutting the patch in proper shape and replastering the surfaces of
the walls including disposal of rubbish to the Camping ground within a
lead of 50 metres with.
(a) Lime mortar 1:2 (1Lime, 2Sand) sqm. 153.5
(b) Cement mortar 1:3 (1Cement, 3Sand) sqm. 179.3
(c) Cement mortar 1:4 (1Cement, 4Sand) sqm. 168.6
(d) Cement mortar 1:6 (1Cement, 6Sand) sqm. 158.0
1417 Turning tiles for repairs(single country, Allahabad or Manglore tiles) sqm. 14.8
excluding cost of tiles.
1418 Turning tiles for repairs(double country or Allahabad tiles) excluding cost sqm. 22.3
of tiles.
1419 Removing of old wornout hessian based felt treatment from roof and sqm. 15.7
parapet walls.
1420 Cleaning and brushing the surface. sqm. 4.7
1421 Preparing the base surface filling the cracks and pot holes whenever sqm. 17.5
necessary with cement mortar(1:3)
1422 Removing old plaster or edges, cleaning of joints and floor for new work sqm. 20.4
and disposal of unserviceable materials within 50m lead
1423 Cleaning of old joints, in required depth for new pointing or plastering and sqm. 17.2
disposal of unserviceable materials within 50m lead
1501 Demolishing below G.L. upto 1 metre depth and disposal of unserviceable
materials within 100 metres lead.
(a) Lime concrete. cum 382.5
(b) Unreinforced cement concrete upto 15 cm thickness. cum 765.1
(c) Unreinforced cement concrete more then 15 cm thickness. cum 1530.1
1502 Demolition R.C.C. work below G.L. upto 1 metre depth including cum 1354.5
stacking of serviceable materials and disposal of unserviceable materials
within 100 metres lead.
1503 Extra over item 1502 for cutting steel bars in R.C.C. (Least sectional area sqm. 332.4
of R.C.C. work to be measured)
1504 Demolition above G.L. upto floor two level including disposal of
unserviceable materials within 100 metres lead.
(a) Lime concrete. cum 394.0
(b) Unreinforced cement concrete upto 15 cm thickness. cum 776.5
(c) Unreinforced cement concrete more then 15 cm thickness. cum 1541.6
1505 Demolishing RCC work above G.L. upto floor two level including cum 1368.1
disposal of unserviceable materials within 100 metres lead.
1506 Extra over item 1505 for cutting steel bars in R.C.C. work (Least sectional sqm. 332.4
area of R.C.C. work to be measured)
1507 Demolition of brick work below G.L. upto 1 metre depth including
stacking of serviceable materials and disposal of unserviceable materials
within 100 metres lead.
(a) In mud mortar . cum 351.2
(b) In lime mortar . cum 429.6
(c) In cement mortar . cum 1006.5
1508 Demolition of brick work above G.L. upto floor two level including
stacking of serviceable materials and disposal of unserviceable materials
within 100 metres lead.
(a) In mud mortar . cum 361.7
(b) In lime mortar . cum 442.4
(c) In cement mortar . cum 1021.6
1509 Extra over items1507& 1508 for removing mortar from and cleaning
bricks including removal of rubbish within 100 metres lead.
(a) Brick work in mud mortar. cum 664.1
(b) Brick work in lime mortar. cum 760.9
(c) Brick work in cement mortar. cum 947.3
1510 Demolition of stone masonry below G.L. upto 1 metre depth including
stacking of serviceable materials and disposal of unserviceable materials
within 100 metres lead.
(a) Rubble masonry in lime mortar . cum 429.6
(b) Rubble masonry in cement mortar. cum 1006.5
1511 Demolition of stone masonry above G.L. upto floor two level including
stacking of serviceable materials and disposal of unserviceable materials
within 100 metres lead.
(a) Rubble masonry in lime mortar . cum 442.4
(b) Rubble masonry in cement mortar . cum 1021.6
(c) Dressed stone in cement mortar . cum 1220.4
1513 Dismantling tiled floors laid in mortar upto floor two level including
stacking of serviceable materials and disposal of unserviceable materials
within 100 metres lead. (wooden\ concrete joists to be measured and paid
for separately)
(a) For thickness of tiles upto 25 mm . sqm. 29.4
(b) For thickness of tiles above 25 mm sqm. 41.4
(c) Stone slab floor sqm. 92.5
1514 Dismantling sheet roofing including ridges, hips, valleys, gutters etc.
stacking the serviceable materials and disposal of unserviceable materials
within 100 metres lead.
(a) G.I. sheet roofing sqm. 56.8
1514 Dismantling sheet roofing including ridges, hips, valleys, gutters etc.
stacking the serviceable materials and disposal of unserviceable materials
within 100 metres lead.
(b) A.C. sheet roofing sqm. 64.7
1515 Dismantling Tiled roofing with battens boarding etc. including stacking of
serviceable materials and disposal of unserviceable materials within 100
metres lead.
(a) Single Mangalore Rani Ganj, Allahabad or similar tiling. sqm. 79.3
(b) Double Allahabad tiling or Mangalore roofing tiles with ceiling tiles sqm. 118.8
or slate roofing.
(c) Country tiles (Single layer) sqm. 79.3
(d) Country tiles (Double layer) sqm. 118.8
1516 Demolition of thatch roofing including mats, bamboo jaffari, capping to sqm. 38.2
ridges, hips, etc. including stacking of serviceable materials and disposal
of unserviceable materials within 100 metres lead.
1517 Dismantling cement asbestos celotex/ hard board in ceiling or partition sqm. 28.9
walls including stacking of serviceable materials and disposal of
unserviceable materials within 100metres lead.(frame work such as joists,
beams to be measured and paid for separately)
1518 Dismantling ballies in posts, purlins or rafters including stacking the RM 6.9
materials within 100 metres lead.
1519 Dismantling doors, windows and clear storey windows, ventilators etc.
(wood or steel) shutters including choukhats, architraves, hold fasts and
other attachments etc. complete and stacking them within 100 metre lead.
(a) Not exceeding 3 sqm. in area Each 115.4
(b) Exceeding 3 sqm. in area Each 154.9
1520 Taking out doors, windows and clear storey windows, shutters (steel or
wood) including stacking within 100 metre lead.
(a) Not exceeding 3 sqm. in area Each 58.7
(b) Exceeding 3 sqm. in area Each 78.3
1521 Dismantling barbed wire or flexible wire rope in fencing including making sqm. 8.7
rolls and stacking within 100 metres lead (frame work to be measured and
paid for separately)
1522 Dismantling and stacking within 100 metres lead fencing posts or struts
(wood, steel or R.C.C.) including all earth work and dismantling of
concrete etc. in the base and making good the disturbed ground.
(a) Wooden posts of any size RM 246.3
(b) Steel sections of any size RM 249.7
(c) R.C.C. posts of any size RM 319.3
1523 Dismantling ballies or wooden posts at the points of projection above the Each 15.2
concrete or ground including taking out iron steps, bolts nuts etc. if any,
and stacking the same within 100 metres lead.
1601 Providing plinth protection, 50mm thick in cement concrete 1:3:6 sqm. 117.4
(1cement, 3coars sand, 6graded stone aggregate 20mm nominal size)
including finishing the surface of concrete smooth.
1602 Providing plinth protection, with bricks of class 35 in cement mortar 1:6 sqm. 354.8
(1cement, 6fine sand) including pointing top surface of bricks with cement
mortar 1:2 (1cement, 2sand)
1603 Brick edging (brick laid on edge) to plinth protection with bricks of class RM 34.4
35 including grouting with cement mortar 1:4 (1cement, 4fine sand)
1604 Providing and fixing aluminium step 'L' shape to stairs.
1606 Providing and fixing 25mm bore galvanised M.S. tube (medium grade) RM 437.5
outlet in cement mortar 1:3 (1cement, 3fine sand) including cutting and
making good the wall.
1607 Providing and fixing 40mm nominal bore galvanised M.S. tube (medium
grade) outlet in cement mortar 1:3 (1cement, 3fine sand)
(a) Using emulsion with Aldrin, Heptachlor or Chlordane cum 746.1
(b) Using emulsion with Dieldrin cum 763.7
1609 Treating the bottom and sides of excavation at the rate of 5 litres per sqm
of surface area for antitermite treatment.
(a) Using emulsion with Aldrin, Heptac sqm. 1081.3
(b) Using emulsion with Dieldrin sqm. 2128.5
1610 Treating the back fill in contact with foundation at the rate of 15 litres per
sqm of vertical surface. (area of the sub-structure)in contact with back fill
to be measured) for anti-termite treatment.
(a) Using emulsion with Aldrin, Heptachlor or Chlordane sqm. 733.3
(b) Using emulsion with Dieldrin sqm. 755.5
1611 Treating the top surface of filled earth at the rate of 5 litres per sqm of
surface area for antitermite treatment.
1612 Treating the soil along external perimetre of building at the rate of 1 5 sqm. 493.0
litres per sqm of the perimetre wall for antitermite treatment.
1613 Broken glass coping as specified on top of walls in cement mortar 1:3 sqm. 80.7
1615 Construction of Black Board surface on wall in C.M. 1:3 (Projecting 6 sqm. 194.2
mmm. out of plastered surface of walls including painting with black
board paint and finishing to the true shape and size with 40 mm wide
alround boarder of cement mortar 1:3
1701 Boring holes with auger in all types of soil upto 5m depth below G.L.
including collection samples.
(a) 200 mm dia RM 391.8
(b) 250mm dia RM 512.4
(c) 300 mm dia RM 602.8
1704 Theodolite work involving fixing of stones at every tenth chain, tangent, km. 3616.8
apex and vertex points final alignment.
1705 Fly levelling for fixing temporary bench marks.
(a) Chain and compass survey along ridge line km. 1808.4
(b) Levelling along ridge line and cross sections km. 3616.8
1802 Collection of approved soil having CBR not less than 5, including cum 186.3
stacking at quarry.
1803 Collection of approved soil having CBR not less then 12, including cum 217.3
stacking at quarry.
1804 Collection of hard metal other then black trap basalt and granite for road
works (without blasting) including stacking as per MOST 1995, clause
400.2.5
(a) Grading - 1 (Size ranging from 90 mm to 45 mm) cum 496.7
(b) Grading - 2 (Size ranging from 63 mm to 45 mm) cum 605.4
(c) Grading - 3 (Size ranging from 53 mm to 22.4 mm) cum 683.0
1805 Collection of hard metal other then black trap basalt and granite for
building work (without blasting) .
(a) 40 mm nominal size cum 683.0
1806 Deduct from item 1804 and 1805 above for metal breaking with Govt. cum 217.3
boulders and excavated rock.
1807 Collection of boulders at source (maximum size 0.014cum) without cum 170.7
quarrying i.e. picked up boulders.
1808 Collection of quarried stone or rubble.
1810 Collection of size stone for coursed rubble masonry rectangular in shape
(maximum size 0.014cum to 0.06cum) including 20%headers.
(a) Other then black trap Basalt or granite cum 585.2
(b) Black trap Basalt or granite cum 643.8
1811 Collection of rubble masonry (size 0.014cum to 0.06cum) other then black cum 771.5
trap, basalt or granite.
1812 Collection of face stones for dam masonry hammer dressed on face, with
one line chisel dressed 75mm depth from face on bed, top and sides and
hammer dressed below 75mm depth of the stone up to rear face beyond
this depth of 75mm the stones may taper, but minimum length specified
having at least half the area of the face, comprising of hammer dressed
size for coursed rubble masonry rectangular in shape (maximum size
0.014cum to 0.06cum) including 20%headers. Other then black trap,
basalt or granite.
(a) Stretcher- size 55 x 35 x 30 cm Each 192.4
(b) Header- size 60 to 45 x 30 x 30 cm Each 200.7
(c) Bond stone-size 70 to 60 x 30 x 30 cm Each 225.8
1813 Collection of pitching stones size 20 to 25cm and not less then 0.021cum
(without dressing)
(a) Other then black trap Basalt or granite cum 336.9
(b) Black trap Basalt or granite cum 370.6
1814 Collection of pitching stones size 28 to 32cm and not less then 0.024cum
(without dressing)
(a) Other then black trap Basalt or granite cum 274.8
(b) Black trap Basalt or granite cum 302.3
1815 Extra rate for blasting for item 1804 and 1805
1816 Extra rate for black trap basalt, granite. for items 1804, 1805, 1808, 1811 cum 10% of
& 1812 respective item
1817 Stacking and boxing.
1819 Screening-
1820 Washing sand, metal, shingle or gravel (Payable on prior written cum 155.2
permission of S.E.)
1821 Collection of boulders or rubble from excavated materials. cum 99.3
1823 Collection of sand including screening, washing, stacking and all leads cum 232.8
and lifts up to the loading point.
1901 Transportation charges of water for every additional 200m or part thereof,
beyond initial lead of 200m up to 2 Km. Lead for -
(a) Consolidation of Moorum /earth work (rate for 1Cum. of Moorum cum 3.0
/earth work)
(b) Puddle work (rate for 1Cum. of earth work) cum 4.2
(c) Construction of masonry or concrete(rate for 1Cum. of masonry or cum 16.6
concrete)
(d) Metal consolidation of W.B.M. Road(rate for 1Cum. of Metal) cum 6.6
(a) For every 0.5 Kms. Lead beyond 5 Kms. and part there of upto 10 cum 5.3
Kms.
(b) For every 0.5 Kms. Lead beyond 10 Kms. and part there of upto 30 cum 4.0
Kms.
(c) For every 0.5 Kms. Lead beyond 30 Kms. and part there of upto 50 cum 3.6
Kms.
(d) For every 0.5 Kms. Lead beyond 50 Kms. and part there of upto 100 cum 3.3
Kms.
(e) For every 0.5 Kms. Lead beyond 100 Kms. cum 2.6
1913 Loading of materials other then metal, cement and steel in truck, dumper, Rate of item
trolly etc. 1911 multiplied
by % given in
item 1904
1914 Unloading of materials other then metal, cement and steel in truck, Rate of item
dumper, trolly etc. 1912 multiplied
by % given in
item 1904
1915 Extra rate for loading in truck, dumper etc for NP2 pipes (dia above 50% of the
400mm)NP3 pipes and heavy pieces of other materials (each piece of amount arrived
more then 300kg) in item 1913
1916 Extra rate for unloading from truck, dumper, etc. for NP2 pipes (dia above 50% of the
400mm)NP3 pipes and heavy pieces of other materilas(each piece of more amount arrived
then 300kg) in item 1914
2001 Preparation of sub grade by excavating earth work to the 15cm average
depth, dressing to camber including making good the undulations etc. and
disposal of surplus earth with lead upto 50metres and upto 1.5metre.
(a) Loose or soft soil sqm. 14.5
(b) Dence or hard soil sqm. 18.5
2004 Labour only for boulder soling hand packed excluding consolidation. cum 192.0
2005 Labour only for spreading, hand packing, and levelling to gradient and cum 131.8
required camber as per MOST 2004 clause 404.3.3 of metal, grade-1 As
per MOST 2004 clause 400.2.5 including dressing.
2006 Labour only for spreading, hand packing, and levelling to gradient and cum 100.7
required camber as per MOST 2004 clause 404.3.3 of metal grading-2 &
3 as per MOST 2004 clause 400.2.5 including dressing.
2007 Labour only for moorum, screening or binding material as per MOST cum 42.7
2004 clause 400.2.6 spreading on boulder or WBM coat as per MOST
2004 clause 404.2.7
Page 81 of 132
Code Description Unit Rate (Rs.)
2008 Rolling & Compaction of granular sub-base of well graded material, cum 55.2
spreading in uniform layers with tractor mounted grader on prepared
surface, mixing by mix in place, sprinkling of water till OMC, and
compacting with smooth wheel rollers of 80 to 100 kN static weight to
achieve the desired density, complete as per Technical Specification
Clause 401 of Specification for Rural Roads.i/c all leads of water etc.
complete.
2009 Deleted ---- ----
2010 Rolling and consolidating water bound mecadam coat with any size of
metal of any thickness upto 100mm thickness(including rolling screening
or binding materials) including watering & filling in depressions which
occur during the process with power roller exceeding 8 tonne as per
MOST 2004 clause 404.3.4 to 404.3.8
(a) Including hire and running expenses of roller sqm. 8.1
(b) Excluding hire and running expenses of roller sqm. 1.1
2012 Metal patch repair of WBM surface including picking of old surface and cum 1064.9
spreading metal and screening material, consolidation or compaction by
hand ramming etc. complete
2013 Providing laying and compacting of 40mm thick metal renual coat in wet cum 715.4
season including picking old road surface, spreading of clean and crushed
aggregate grading - 3, screenings and korebandi and rolling with power
roller exceeding 8 tonne as per MOST 2004 clause 404.
2014 Providing laying and compacting of W.B.M. sub base/ base course
including preparation and compaction of sub base and spreading of clean
and crushed aggregate to proper grade and camber including application
of screenings for interlocking, sprinkling of water and rolling with power
roller as per clause 404 (excluding inverted choke and scarifying of
existing bitumenous surfaces) for-
(a) Grading No. 1 Material, (90 to 45mm size) with moorum as cum 837.4
screening
(b) Grading No. 2 Material, (63 to 45mm size) with moorum as cum 826.2
screening
(c) Grading No. 3 Material, (53 to 22.4mm size) with moorum as cum 856.4
screening
2015 Preparing surface by brushing with wire brushes for remaining caked mud
etc. sweeping with brooms and finally fanning the cleaned surface with
gunny bags to remove all loose dirt etc.
(a) Water Bound Mecadam surface sqm. 26.7
(b) Black top surfaces sqm. 16.0
2016 Heating binder upto required temperature including fuel for heating MT 3622.7
2017 Heating binder upto required temperature excluding fuel for heating MT 2249.5
2018 Labour only for applying evenly a priming/ tack coat with the bituminous sqm. 6.5
primer(bitumen 80/100) @ 10kg./10 sqm on WBM surface.
2019 Labour only for screening and spreading aggregates for black top roads cum 331.4
2020 Rolling & compacting of B.T. surface for Surface dressing coat or pre mix
carpet or seal coat with power roller exceeding 8 tonne.
(a) Including hire and running expenses of roller sqm. 4.1
(b) Excluding hire and running expenses of roller sqm. 1.0
2021 Providing and applying evenly a priming coat with the bituminous sqm. 40.8
emulsion @ 9kg./10 sqm
Page 82 of 132
Code Description Unit Rate (Rs.)
2022 Providing tack coat as per MOST clause 503 over existing primed surface
with bituminous emulsion.
(a) Normal B.T. surface @ 2.50 kg./10 Sqm. area. sqm. 12.9
(b) Granular surface (Primed)/ Cement concrete surface @ 3.00 kg./10 sqm. 16.5
Sqm. area.
(c) Granular surface (Not Primed) @ 10 kg./10 Sqm. area. sqm. 45.3
2023 Providing single coat surface dressing with paving bitumen using 18kg. of sqm. 98.2
bitumen VG - 10 (80/100 penetration) per 10 sqm with 0.15cum of stone
chipping 13.2mm nominal size per 10 sqm of road surface for second coat
and rolling complete with power roller exceeding 8 tonne.
2024 Surface dressing two coats with paving bitumen using 18kg. of bitumen sqm. 157.3
VG - 10 (80/100 penetration) per 10sqm with 0.15cum of stone chipping
13.2mm nominal size per 10sqm for 1st coat and 11kg. of bitumen VG -
10 (80/100 penetration) per 10sqm with 0.10cum of stone chipping
11.2mm nominal size per 10sqm of road surface for second coat and
rolling complete with power roller exceeding 8 tonne.
2025 2cm consolidated thick single coat premix carpet surfacing with 0.27cum sqm. 97.3
of stone chippings (13.2mm Size 0.18cum and 11.2mm size 0.09cum)
mixed with 14.6kg. of binder [bitumen VG - 10 (80/100 penetration)] per
10sqm of road surface and rolling complete with power roller exceeding 8
tonne.
2026 2.5cm consolidated thick single coat premix carpet surfacing with sqm. 118.4
0.30cum of stone chippings 11.2mm Size 0.18cum mixed with 19.2kg
bitumen VG - 10 (80/100 penetration) per 10sqm of road surface and
rolling complete with power roller exceeding 8 tonne.
2027 Liquid seal coat(I.R.C. type A) with 0.09cum of stone chippings 6.7mm sqm. 58.4
size and down graded 9.8kg. of bitumen VG - 10 (80/100 penetration) per
10 sqm of road surface.
2028 Pre-mixed seal coat (type B) with 0.06cum of stone chippings, passing sqm. 43.3
2.36mm size and retained on 180 micron IS sieve and 6.8kg. of bitumen
VG - 10 (80/100 penetration) per 10 sqm of road surface.
2029 Providing and filling in foundation trenches and at the back of abutments,
wing walls etc. and below pipe bed in layers not exceeding 15cm thick
including watering and compacting including all lead and lifts.
(a) Good local sand free from earth. cum 598.2
(b) Selected granular material in filling. cum 584.6
2030 Precast Cement Concrete M15 kerb including fixing at site. RM 163.6
2031 Painting two coats after filling the surface with synthetic enamel paint in sqm. 63.4
all shades on new plastered concrete surface.
2032 Deleted ----- -----
2033 Providing and laying reinforced cement concrete pipes N.P.2 for culverts
including pointing ends, and fixing collar with cement martar 1:2
complete.
(a) 300 mm dia RM 468.9
(b) 450mm dia RM 846.2
(c) 600mm dia RM 971.6
(d) delete ------ -----
2034 Laying reinforced cement concrete pipes N.P.2 for culverts including
pointing ends, and fixing collar with cement martar 1:2 complete.
(a) 300mm dia RM 44.4
(b) 450mm dia RM 66.3
Page 83 of 132
Code Description Unit Rate (Rs.)
2034 Laying reinforced cement concrete pipes N.P.2 for culverts including
pointing ends, and fixing collar with cement martar 1:2 complete.
(c) 600mm dia RM 88.2
(d) delete ---- ----
2035 Providing and laying reinforced cement concrete pipes N.P.3 for culverts
including pointing ends, and fixing collar with cement martar 1:2
complete.
(a) 900 mm dia. RM 3490.3
(b) 1000 mm dia. RM 3853.2
(c) 1200 mm dia. RM 4775.4
(d) 600 mm dia. RM 1512.8
2036 Laying reinforced cement concrete pipes N.P.3 for culverts including
pointing ends, and fixing collar with cement martar 1:2 complete.
(a) 900 mm dia. RM 247.9
(b) 1000 mm dia. RM 264.7
(c) 1200 mm dia. RM 292.4
(d) 600 mm dia. RM 201.6
2040 Loosening, Levelling and Compacting original ground, supporting cum 10.0
embankment to facilitate placement of first layer of embankment, scarified
to a depth of 150 mm, spreading in 4% camber and required gradient with
tractor mounted grader or labourers, watering at OMC and compacted by
80 to 100 kN static weight rollers to achieve desired density minimum
97% as given in tables 300.1 and 300.2 for embankment construction as
per specifications for rural roads (MORD) clause 301.4.1 (This work shall
be executed with prior written permission of SE)
2041 Compaction of embankment with approved materials as per clause 301.4 cum 16.9
& 301.5 of specifications for rural roads(MORD), already spreaded at site,
obtained from roadway cutting, excavated from drains, foundation of other
structures or from borrow pit, making 4% camber and required Grade by
tractor mounted grader or labourers, watering at OMC and compacted by
80 to 100 kN static weight rollers to achieve desired density minimum
97% as per table 300.1 and 300.2 of (MORD) - i/c required leads and lifts
of materials etc. complete.
2042 Compaction of soil for construction of subgrade & earthen shoulders with cum 18.9
approved material, already spreaded at site, obtained from roadway
cutting, drains, foundation of other structures or barrow pits, i/c making
4% camber and required grade by tractor mounted grader or labourers,
watering at OMC and compacted by 80 to 100 kN static weight rollers to
achieve desired density minimum 100% of the MDD as per IS:2720
(Part-7). Complet compaction work as per specifications for rural roads
(MORD) clause 303, i/c required leads and lifts of materials etc. complete.
2043 Compaction of soil for construction of subgrade & earthen shoulders with cum 24.7
approved transported material collected and stacked at site, i/c spreading,
making 4% camber and required gradient by tractor mounted grader or
labourers, watering at OMC and compacted by 80 to 100 kN static weight
rollers to achieve desired density minimum 100% of the MDD as per
IS:2720 (Part-7). Complete compaction work as per specifications for
rural roads (MORD) clause 303, i/c required leads and lifts of materials
etc. complete.
2044 Construction of hard shoulder as per clause 407 of specifications for rural cum 370.2
roads (MORD), with soil having CBR value not less than 12, inclusive of
all leads and lifts, providing 4-5% camber by tractor mounted grader or
labourers, watering at OMC and compacted by 80 to 100 kN static weight
rollers to achieve desired density minimum 100% of the MDD as per
IS:2720 (Part-7), i/c all leads and lifts of materials etc. complete.
2045 Compaction of hard shoulder collected at site, i/c making 4-5% camber by cum 35.9
tractor mounted grader or labourers, watering at OMC and compacting
with 80 to 100 kN static weight rollers to achieve desired density
minimum 100% of the MDD as per IS:2720 (Part-7), as per clause 407 of
specifications for rural roads(MORD), i/c required leads and lifts of
materials etc. complete.
Page 85 of 132
Code Description Unit Rate (Rs.)
2049 "Construction of Gravel Surface Course as per clause 402 of "Ministry of cum 508.6
Rural Development, Specifications for Rural Roads-August, 2004" by an
appropriate combination of natural gravel, river borne material and
crushed metal in required proportions confirming to Grading requirements
specified in clause 2.2.2.2 or clause 2.2.2.3 (Table 2.3, Material having
Nominal Maximum Size 20 mm or 10 mm) of IRC:SP:77-2008, having
Liquid Limit less than 40 and Plasticity Index 6-15 and strength of
material not less than 20% CBR, including all leads and lifts of material
etc. complete. The mixing shall be by Mix-in-Place method over prepared
surface, spreading in uniform layers with tractor mounted grader or
manually, watering at OMC and compaction by smooth wheeled/vibratory
roller of 80 to 100 kN static weight to achieve 100% of MDD as per
IS:2720 (Part-7)".
2050 Excavation, Carting i/c Removal of Soil with Disposal upto 1000 m cum 42.0
2053 Deduct from item 2051 or 2052 if static roller is used in place of vibratory cum 6.6
rollers.
2054 Deduct from item 2051 or 2052 if motor grader is not used. cum 6.9
2055 Deduct from item 2051 or 2052 if Tractor Mount Grader, more than 65 cum 4.7
HP (6 wheel - 4 wheel drive) is used in place of motor grader.
Page 87 of 132
21 - WATER SUPPLY & FITTINGS
NOTES:
21.1 All leads and lifts of all matrerials unless otherwise specified.
21.2 The materials used shall conform to the relevant I.S.S.
21.3 The rates for pipeline, include laying of pipeline below ground or fixed to the walls,
steel tubings with steel socket joints, together with all tube fittings (such as bends, elbows,
tees, reducers, plugs, unions, sleeve pieces, etc.) and fixing complete with
holder-bat-clamps or wall-hooks (when pipe is fixed in chases), wooden plugs, making
holes in the walls for crossing the pipe and repairing the same with cement mortar 1:3 to
the original condition, excavation of trenches of required depth and width in all type of
soils, refilling the trenches, with surface properly dressed and rammed.
21.4 The rates for laying and fixing include all labour and materials, tools and plants other
than tubes and fittings.
Measurements :
(i) All work shall be measured net as fixed to the nearest 0.01 m unless otherwise stated.
(ii) The pipe line shall be measured net as fixed, including the length of all fittings
(measured along the centre line) and no allowance shall be made for wastage etc.
21.5 The following Indian Standards may be referred to :
I.S. No. Title
554-1975 Dimensions for pipe threads where pressure joints are required on the
threads (second revision) (with amendment No.1)
778-1980 Copper alloy gate, globe and check valves for water supply purposes
(third revision)
781-1977 Cast copper alloy screw-down bid taps and stop valves for water services
(second revision) (with amendment no.1)
782-1978 Caulking lead (third revision)
1068-196 Electroplated coating of nickle and chromium on iron and steel (first
revision) (with amendment No.1&2)
1172-197 Code of basis requirements for water supply, drainage and sanitation
(second revision)
1239 Mild steel tubes, tubular and other wrought steel fittings.
1239-(Pt.I.)1979 Part I-Mild steel tubes (fourth revision) (with amendment No.1)
1239 (Pt.ii.)1969 Part II-Mild steel tubulars and other wrought steel pipe fittings (second
revision)
1711-1970 Self-closing taps (first revision) (with amendment 1 & 2) (reaffirmed
1979)
1795-1974 Pillar taps for water supply purposes (first revision) (with amendment 1 to
4)
2065-1972 Code of practice for water supply in buildings (first revision)
2629-1966 Recommended practice for hot dip galvanising of iron and steel.
2692-1978 Ferrules for water services (first revision)
4346-1978 Washers for water taps for cold water services (reaffirmed 1979)
4736-1968 Hot-dip zinc coating on steel tubes.
9763-1981 Plastic bib taps and stop valves (rising spindle for cold water services)
Code Description Unit Rate (Rs.)
2101 Providing and fixing to wall ceiling and floor galvanised mild steel tubes
(medium grade) of the following nominal bore, tube fittings and clamps
including walling making good the wall, ceiling and floor
2103 Fixing G.I pipe line, with all materials except pipe, fitting and clamps but
including making good the walls and floors etc. complete (for item 2101)
(a) 15 mm dia. RM 49.6
(b) 20 mm dia. RM 52.9
(c) 25 mm dia. RM 56.3
(d) 32 mm dia. RM 66.8
(e) 40 mm dia. RM 84.5
(f) 50 mm dia. RM 102.5
2104 Providing and laying in trenches galvanised mild steel tubes (medium
grade) of the following nominal bore, tube fittings (earth work in trenches
to be measured and paid for separately)
(a) 15 mm dia. RM 80.0
(b) 20 mm dia. RM 97.8
(c) 25 mm dia. RM 129.3
(d) 32 mm dia. RM 160.4
(e) 40 mm dia. RM 178.2
(f) 50 mm dia. RM 227.1
(g) 65 mm dia. RM 308.9
(h) 80 mm dia. RM 402.3
(i) 100 mm dia. RM 584.6
2106 Laying G.I pipe line, with all materials except pipe, fitting and clamps but
including excavation of trenches and refilling etc. complete (for item
2104)
(a) 15 mm to 20 mm dia. RM 8.9
(b) 25 mm to 32 mm dia. RM 13.7
(c) 40 mm to 50 mm dia. RM 18.1
(d) 65 mm to 100 mm dia. RM 33.1
2107 Providing and fixing to wall, ceiling and floor 6.00kgf/sqcm working
pressure polyethylene pipes of the following outside diameter low density
complete with special flange compression type fitting wall clips etc.
including making good the wall ceiling and floor.
(a) 20 mm dia. RM 54.3
(b) 25 mm dia. RM 56.4
(c) 32 mm dia. RM 62.4
(d) 40 mm dia. RM 76.0
(e) 50 mm dia. RM 86.1
2108 Providing and fixing to wall, ceiling and floor 6.00kgf/sqcm working
pressure polyethylene pipes of the following outside diameter high density
complete with special flange compression type fitting wall clips etc.
including making good the wall ceiling and floor.
(a) 32 mm dia. RM 72.9
(b) 40 mm dia. RM 84.4
(c) 50 mm dia. RM 95.1
2115 Fixing water meter and stop cock in galvanised mild steel tube of the Each 239.4
following nominal bore including necessary fittings such as mild steel
galvanised jamnut, socket etc cutting and threading the tube and making
long screws complete (water meter, jam nut and stop cock to be measured
and paid for separately)
2116 Providing and fixing 600mm X 450mm bevelled edge mirror of superior nos. 559.8
glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to
wooden plugs with C.P. brass screws and washers.
2117 Labour only for item no.2116 nos. 213.0
2118 Providing and fixing 600mm X 120mm glass shelf with C.P. brass nos. 386.2
brackets and guard rail complete, fixed to wooden plugs with C.P. brass
screws.
2119 Labour only for item no.2118 nos. 161.4
2120 Providing and fixing C.P. brass towel rail complete with C.P. brass
brackets fixed to wooden plugs with C.P. brass screws.
(a) 750 x 20mm. size. Each 483.9
(b) 600 x 20mm. size. Each 422.1
2122 Providing and fixing liquid soap Glass container with C.P. brass lid and nos. 270.6
brackets fixed to wooden plugs with C.P. brass screws.
2123 Labour only for item no.2122 nos. 77.5
2124 Providing and fixing Chromium Plated brass dish with C.P. brass brackets nos. 261.8
fixed to wooden plugs with C.P. brass screws.
2125 Labour only for item no.2124 nos. 77.5
2126 Providing and fixing ferule of the following nominal bore including
boring.
(a) 15mm nominal bore. Each 113.2
(b) 20mm nominal bore. Each 157.7
(c) 25mm nominal bore. Each 167.1
2129 Providing and Fixing capstan head with porcelain disc marked hot or cold,
bib taps of the following nominal bore.
(a) 15mm dia. Each 173.6
(b) 20mm dia. Each 203.4
(c) 25mm dia. Each 241.3
2130 Providing and Fixing 15mm dia Chromium plated Bib Taps of the Each 241.1
following nominal bore.
2131 Providing and fixing 15mm dia pillar taps, capstan head screw down, high Each 289.3
pressure lettered 'Hot' or 'Cold' with long screws, shanks and bank nuts of
the following nominal bore.
2132 Labour only for item no.2128, 2129, 2130 & 2131
2139 Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.
2143 Providing and fixing in position best Indian make G.I. Tees (equal) in G.I.
Pipe including cutting and threading the pipe and making long screws etc.
complete (New work)
(a) 15 mm dia. Each 33.0
(b) 20 mm dia. Each 40.2
(c) 25 mm dia. Each 47.3
(d) 32 mm dia. Each 76.2
(e) 40 mm dia. Each 85.1
(f) 50 mm dia. Each 112.1
2145 Providing and fixing in position best Indian make G.I. Bend in G.I. Pipe
including cutting and threading the pipe and making long screws etc.
complete (New work)
(a) 15 mm dia Each 28.2
(b) 20 mm dia. Each 37.2
(c) 25 mm dia. Each 48.9
(d) 32 mm dia. Each 74.1
(e) 40 mm dia. Each 92.1
2145 Providing and fixing in position best Indian make G.I. Bend in G.I. Pipe
including cutting and threading the pipe and making long screws etc.
complete (New work)
(f) 50 mm dia. Each 110.0
2147 Providing and fixing in position best Indian make G.I. Union in G.I. Pipe
including cutting and threading the pipe and making long screws etc.
complete (New work)
(a) 15 mm dia. Each 55.5
(b) 20 mm dia. Each 67.2
(c) 25 mm dia. Each 80.7
(d) 32 mm dia. Each 101.4
(e) 40 mm dia. Each 119.3
(f) 50 mm dia. Each 155.3
2149 Providing and placing on terrace (at all floor levels) polyethylene water ltr. 5.3
storage tank ISI : 12701 marked with cover and suitable locking
arrangment and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank.
2150 Labour only for item 2149 ltr. 7% of item no.
2149
2201 Providing and fixing water closet squatting pan (Indian type W.G. pan)
size 580mm (earth work bed concrete, foot rests and trap to be measured
and paid for separately)
(a) Vitreous China Long pattern- white colour Each 784.9
(b) Vitreous China Orissa pattern - white colour Each 917.4
(c) Vitreous China Orissa pattern- standard colour Each 961.5
(d) Glazed earthenware Long pattern Each 917.4
(e) Glazed earthenware Orissa pattern Each 802.5
2202 Providing and fixing wash down water closet squatting pan (European
type W.C. pan) with integral 'P' or 'S' trap including jointing the trap with
soil pipe in cement mortar 1:1 (1cement, 1fine sand) - (seat and cover to
be measured and paid for separately)
(a) Vitreous China -Pattern 1 in white colour Each 1204.4
(b) Vitreous China -Pattern 1 in standard colour. Each 1270.7
(c) Vitreous China -Pattern 2 in white colour. Each 1182.3
(d) Vitreous China -Pattern 2 in standard colour. Each 1429.6
(e) Glazed Earthenware-Pattern 1 Each 1094.0
(f) Glazed Earthenware-Pattern 2 Each 1138.2
(g) Glazed Earthenware-Pattern 3 Each 1182.3
2203 Labour only for item no.2201 & 2202 Each 352.2
2204 Providing and fixing 100mm size 'P' or 'S' trap for water closet squatting
pan including jointing the trap with pan and soil pipe in cement mortar 1:1
(1cement, 1fine sand)
(a) Vitreous china Each 338.7
(b) Glazed earthenware. Each 321.5
(c) Sand Cast Iron. Each 369.0
2206 Providing and fixing in cement mortar 1:3 (1cement, 3 coarse sand) a pair Pair 161.4
of white vitreous China 250mm X 130mm X 30mm foot rest for long
pattern squatting pan water closet.
2207 Labour only for item no.2206 Pair 24.0
2208 Fixing 12.5 litres low and high level flushing cistern with a pair of C.I. Or
M.S. brackets complete with fittings each as lead valve loss syphon.
15mm nominal size brass ball valve with polythene float, C.P. brass
handle, unions and couplings for connection with inlet, outlet and over
flow pipes, 40mm dia porcelain enamelled flush bend including cutting
holes in walls and making good the same and connecting the flush bend
with cistern and closet (overflow pipe to be measured and paid for
separately)
(a) Vitreous China white colour low level Each 1390.4
(b) Vitreous China white colour high level Each 1652.0
2209 Providing and fixing in position with clamps, etc. 32mm nominal internal RM 149.3
diameter galvanised steel tube flush pipe for high level flushing cistern
including connecting the flush pipe with cistern and closet and making
good the walls and floors.
2210 Labour only for item no.2209 RM 62.0
2211 Providing and fixing bowl pattern urinal including connecting the urinal
with waste pipe by means of white lead mixed with chopped hemp (waste
pipe to measured and paid for separately)
(a) Vitreous China flat back type of size 430 mm x 260 x mm x 350 mm Each 676.0
white colour
(b) Vitreous China flat back type of size 430 mm x 260 x mm x 350 mm Each 676.0
in Standard colours except misty-lilac.
(c) Vitreous China angle back type of size 340 mm x 430 mm x 265 mm Each 639.6
in white colour
(d) Vitreous China angle back type of size 340 mm x 430 mm x 265 mm Each 594.1
in standard colour except Misty-Lilac
(e) Glazed Earthenware flat back type of size 430 mm x 260 x mm x Each 588.2
350 mm
(f) Glazed Earthenware angle back type of size 340 mm x 430 mm x Each 503.1
265 mm
2212 Labour only for item no.2211 Each 275.7
2213 Providing and fixing squatting plate pattern urinal of size 600mm X
350mm with integral longitudinal flush pipe.
(a) Vitreous china Each 1175.7
(b) Glazed Earthenware. Each 1088.4
2215 Providing and fixing automatic flushing cistern with a pair of C.I. Or M.S.
brackets, complete with fittings including C.I. Syphonic apparatus
mosquito proof lid, C.P. brass unions and couplings for connection with
inlet, outlet and over flow pipes including cutting holes and making good
the same overflow pipe to be measured and paid for separately
(a) Glazed Earthenware of the following nominal size 5 litres Each 1469.0
(b) Glazed Earthenware of the following nominal size10 litters Each 1730.7
(c) Glazed Earthenware of the following nominal size 15 litters Each 1817.9
(d) Cast Iron of the following nominal size 5 litre Each 1207.4
(e) Cast Iron of the following nominal size10litre Each 1381.8
(f) Cast Iron of the following nominal size 15 litre Each 1469.0
2217 Providing and fixing C.P. brass flush pipe/spreaders for urinal of the
following nominal box with fittings such as unions, clamps etc (all in D.P.
brass) including cutting holes and making good the same.
(a) 15 mm RM 130.4
(b) 20 mm RM 151.7
(c) 25 mm RM 168.0
(d) 32 mm RM 185.1
(a) 15 mm RM 47.2
(b) 20 mm RM 50.4
(c) 25 mm RM 53.6
(d) 32 mm RM 63.6
2219 Providing and fixing wash basin with single hole for pillar tap with C.I. or
M.S. brackets painted white including cutting holes and making good the
same but excluding fitting.
(a) Vitreous China flat back wash basin 630 mm x 450 mm size in white Each 1804.2
colour
(b) Vitreous China flat back wash basin 630 mm x 450 mm size in Each 1892.6
standard colour except Misty-Lilac
(c) Vitreous China Flat back wash basin 550 mm x400 mm size in white Each 1406.8
colour
(d) Vitreous China Flat back wash basin 550 mm x 400 mm size in Each 1450.9
standard colour except Misty-Lilac
(e) Vitreous China Angle back wash basin 600 mm x 480 mm white Each 1450.9
colour
(f) Vitreous China Angle back wash basin 400 mm x 400 mm white Each 1141.8
colour
(g) Glazed earthenware flat back wash basin 630 mm x 450 mm size Each 1627.6
white colour
(h) Glazed earthenware flat back wash basin 550 mm x 400 mm size Each 1186.0
white colour
(i) Glazed earthenware Angle back wash basin 600 x 480 mm size white Each 1362.6
colour
(j) Glazed earthenware Angle back wash basin 400 x 400 mm size white Each 1097.6
colour
2220 Labour only for item no.2219 Each 467.9
2221 Providing and fixing kitchen sink with C.I. or M.S. brackets painted white
including cutting holes and making good the same but excluding fitting.
(a) White glazed fire clay sink 600 mm x 450 mm x 150 mm Each 1798.0
(b) White glazed fire clay sink 600 mm x 450 mm x 250 mm Each 1886.3
(c) White glazed fire clay sink 750 mm x 450 mm x250 mm Each 2062.9
(d) Terrazzo finish sink 600 mm x 450 mm x 150 mm Each 1665.5
(e) Terrazzo finish sink 600 mm x 450 mm x 250 mm Each 1842.1
(f) Terrazzo finish sink 750 mm x 450 mm x 250 mm Each 1886.3
(g) Vitreous China sink 600 mm x 450 mm x 150 mm Each 1709.6
(h) Vitreous China sink 600 mm x 450 mm x 250 mm Each 1886.3
(i) Vitreous China sink 750 mm x 450 mm x 250 mm Each 1974.6
2223 Providing and fixing laboratory sink with C.I. or M.S. brackets painted
white including cutting holes in walls and making good the same but
excluding fitting.
(a) Vitreous China 450 mm x 300 mm x 150 mm size Each 1179.7
2223 Providing and fixing laboratory sink with C.I. or M.S. brackets painted
white including cutting holes in walls and making good the same but
excluding fitting.
(b) Vitreous China 600 mm x 400 mm x 200 mm size Each 1533.0
(c) Glazed Earthenware 450 mm x 300 mm x 150 mm size Each 1356.3
(d) Glazed Earthenware 600 mm x 400 mm x 200 mm size Each 1533.0
2225 Providing and fixing C.P. brass waste for wash basin or sink .
2226 Providing and fixing M.I. fisher union for wash basin or sink .
2227 Providing and fixing C.P. brass or M.I. Trap for wash basin and sink.
2228 Providing and fixing plastic seat and cover for wash down water closet
with C.P. brass hinges and rubber buffers.
(a) White plastic seat and cover Each 306.6
(b) Black plastic seat and cover Each 283.0
2234 Providing and fixing asbestos cement fitting. Plain Bend of the following
nominal size including jointing with spun yarn soaked in bitumen and
cement mortar 1:2 complete.
(a) Plain bend.50 mm dia Each 98.7
(b) Plain bend.80 mm dia. Each 103.3
(c) Plain bend.100 mm dia. Each 107.8
2236 Providing and fixing in position A.C. cowls of the following nominal size
including jointing with spun yarn soaked in bitumen and cement mortar
1:2 complete.
(a) Cone cap cowl 50 mm dia. Each 98.7
(b) Cone cap cowl 80 mm dia. Each 107.8
(c) Cone cap cowl 100 mm dia. Each 121.5
(d) Slotted vend cowl 50 mm dia. Each 112.4
(e) Slotted vend cowl 80 mm dia. Each 116.9
(f) Slotted vend cowl 100 mm dia. Each 116.9
2301 Deleted …. ….
2302 Deleted …. ….
RES - NIC MPSU 3 - SPECIAL ITEMS OF EARTH/MASONRY DAM AND CANAL Page 1 of 2
Page 103 of 132
2303 Deleted …. ….
2304 Deleted
RES - NIC MPSU 3 - SPECIAL ITEMS OF EARTH/MASONRY DAM AND CANAL Page 2 of 2
Page 104 of 132
24 - WELL EXCAVATION
NOTES :
24.1 Rates include all lifts (after addition of item 2403 or item 2404 as the case may be)
and removal of excavated materials to a distance of 50 m beyond the well, unless
otherwise Specified.
24.2 Rates of rock cutting are subject to 40 % deduction for voids, if paid on stack
measurements.
24.3 Classification of strata shall be as per Note 3.2 of Chapter 03 “Excavation &
Earthwork”
24.4 For deepening of existing wells, the depth will be considered from platform level.
Code Description Unit Rate (Rs.)
2401 Earth work for well excavation including disposal of excavated soil lead
upto 50m and lift upto 1.5m, disposed soil to be levelled and neatly
dressed.
(a) Loose or soft soil cum 140.5
(b) Dense or hard soil cum 186.0
(c) Hard Moorum cum 241.7
2403 Add in item No. 2401 for lift. (In well excavation)
(a) For every 0.50 m after 1.5 m initial depth upto 6.0 m cum 14.7
(b) For every 0.50 m after 6.0 m initial depth upto 10.5 m cum 19.4
(c) For every 0.50 m after 10.5 m initial depth upto 15.0 m cum 24.5
2404 Add in item No. 2402 for lift. (In well excavation)
(a) For every 0.50 m after 1.5 m initial depth upto 6.0 m cum 21.9
(b) For every 0.50 m after 6.0 m initial depth upto 10.5 m cum 26.7
(c) For every 0.50 m after 10.5 m initial depth upto 18.0 m cum 34.2
2405 Extra rates for quantities of work executed. In or under water or in foul cum 20% of
condition (extra rate for the main item concerned is allowed on account of respective item
slow progress of works)
2510 Providing and fixing IS : 1341 marked M.S. heavy weight butt hinges with necessary screws
etc. complete :
Page 106 of 132
Code Description Unit Rate
(a) 125x90x4.00 mm Each 47.70
(b) 100x75x3.50 mm Each 31.50
(c) 75x60x3.10 mm Each 18.90
(d) 50x40x2.50 mm Each 11.70
2511 Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws
etc. complete
(a) 125x65x2.12 mm Each 28.80
(b) 100x58x1.90 mm Each 20.70
(c) 75x47x1.70 mm Each 15.30
(d) 50x37x1.50 mm Each 9.00
2512 Providing and fixing ISI marked oxidized M.S. pressed Parliamentary hinges with necessary
screws etc. complete :
(a) 150x125x27x2.80 mm Each 52.20
(b) 125x125x27x2.80 mm Each 49.50
(c) 100x125x27x2.80 mm Each 41.40
(d) 75x100x20x2.24 mm Each 35.10
2513 Providing and fixing ISI marked oxidized M.S. single acting spring hinges with necessary
screws etc. complete :
(a) 150 mm Each 152.10
(b) 125 mm Each 146.70
(c) 100 mm Each 117.90
2514 Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc.
complete :
(a) 300x16 mm Each 153.00
(b) 250x16 mm Each 141.30
2515 Providing and fixing ISI marked stainless steel tower bolt black finish, (Barrel type) with
necessary screws etc. complete :
(a) 250x10 mm Each 133.20
(b) 200x10 mm Each 83.70
(c) 150x10 mm Each 63.90
(d) 100x10 mm Each 45.00
2516 Providing and fixing ISI marked oxidized M.S. door latches conforming to IS:5930 with
screws etc. complete:
(a) 300x20x6 mm Each 64.80
(b) 250x20x6 mm Each 60.30
2517 Providing and fixing ISI marked oxidized M.S. handles conforming to IS:4992 with
necessary screws etc. complete :
(a) 125 mm Each 24.30
(b) 100 mm Each 22.50
(c) 75 mm Each 21.60
2518 Providing and fixing stainless steel safty chain with necessary fixtures for doors. Each 244.80
Conforming to IS specification (Weighting not less than 450 gms.)
2519 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws
etc. complete :
(a) 125x64x1.90 mm Each 60.30
(b) 100X58X1.90 mm Each 53.10
(c) 75x47x1.80 mm Each 35.10
(d) 50x37x1.50 mm Each 22.50
2520 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with
stainless steel screws etc. complete :
(a) 125x64x2.50 mm Each 68.40
(b) 100x60x2.50 mm Each 54.00
(c) 75x50x2.50 mm Each 41.40
Page 107 of 132
Code Description Unit Rate
2521 Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :
(a) 75 mm overall thickness partition with 12.5 mm thick double skin fire rated board sqm 1090.80
conforming to IS: 2095: part I.
(b) 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain sqm 814.50
Gypsum board conforming to IS: 2095: part I
(c ) 66mm overall thickness Partition with 8mm thick double skin Calcium Silicate Board sqm 1341.90
made with Calcareous and Siliceous materials reinforced with cellulose fiber
manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm,
Bending Strength 100 kg./ sq.cm.
(d) 66mm overall thickness partition using 8mm thick double skin non- asbestos sqm 1090.80
multipurpose cement board reinforced with cellulose fibre manufactured through
autoclaving process (High pressure steam cured) as per IS: 14862 with suitable fibre
cement screw.
2537 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed Sqm 978.30
shutters for doors, windows and clerestory windows (Area of opening for panel inserts
excluding portion inside grooves or rebated to be measured). Panelling for panelled and
glazed shutters 25 mm to 40 mm thick :
Prelaminated with decorative lamination on both side exterior Grade-I MDF Board 12mm
thick conforming to IS 14587
Page 109 of 132
Code Description Unit Rate
2538 Providing and fixing factory made UPVC door frame made of uPVC extruded section having `
an overall dimension as below (tolerance ±1mm) with wall thickness 2.0mm ( ± 0.2mm),
corners of the door frame to be jointed with galvanized brackets and stainless steel
screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by
galvanized M.S. tube of size 19 X 19mm and 1mm (± 0.1mm) wall thickness and 3 nos.
stainless steel hinges fixed to the frame complete as per manufacturers specification and
direction of Engineer-in-Charge
(b) 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and Sqm 2808.90
rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm)
with inbuilt decorative moulding edging on one side. The styles and rails mitered and
joined at the corners by means of M.S. galvanized/plastic brackets of size 75x220 mm
having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter
reinforced by inserting galvanized M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm)
wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size
100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means
of plastic/ galvanized M.S. 'U' cleats. The shutter frame filled with a uPVC multi-
chambered single panel of size not less than 620 mm, having over all thickness of 20
mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at
two places by inserting horizontally 6 mm galvanized M.S. rod and fastened with nuts
and washers, complete as per manufacturer's specification and direction of Engineer-in-
charge.
( c) 25 mm thick PVC flush door shutters made out of a one piece multi chamber extured Sqm 2703.60
PVC sections of the size of 762mm x 25mm or less as per requiement with an
averaqge wall thickness of 1mm (± 0.3mm) PVC foam end cap of size 23 x10mm or
provided both vertical edges to ensure the overall thickness of 25mm. An M.S. tube
having dimensions 19mm x 19mm and 1.0mm (±0.1mm) is inserted along the hinge
side of the door. Core of the door shutter should be filled with high density
polyurethane foam. The top and bottom edges of the shutter or covered with en end cap
of the sizw 25mm x 11mm doorm shutter shall be reinforced with special polymeric
reinforcements as per manufucred specifications and direction of Engineer-in-Charge
to take up necessary hardware and fixtures. Stickers indicating the locations of
hardware will be pasted at appropiate places.
2540 Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness metre 434.70
of 5mm, made out of extruded 5mm rigid PVC foam sheet mitreed at corners and joined with
2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door frame
profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket
weather seal to be provided through out the frame. The door frame to be fixed to the wall
using M.S. screws of 65/100mm size complete as per manufacturers specification and
direction of Engineer-in-Charge.
Page 110 of 132
Code Description Unit Rate
2541 Providing and fixing PVC rigid foam sheet 1mm thick on existing door shutters (bathroom sqm 563.40
and W.C. doors) using synthetic rubber based adhesive.
2542 Providing and fixing factory made panel PVC door shutter consisting of frame made out of 0.00
M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top
and bottom rails. M.S. frame shall have a coat of steel primers of approved make and
manufacture . M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size
30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in
45degree angle on both side forming styles; and 5mm thick, 95mm wide PVC sheet out of
which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form
top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm
shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided
both side of the panel. 10mm (5mmx2) thick, 20mm wide cross PVC sheet be provided as
gap insert for top rail and bottom rail. paneling of 5mm thick both side PVC sheet to be fitted
in the M.S. frame welded/ sealed to the styles and rails with 7mm (5mm+2mm) thick x
15mm wide PVC sheet beading on inner side, and joined together with solvent cement
adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior
side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-
in-charge. Manufacturer’s specification and drawing.
2549 Providing and fixing glass panes/steel sheet/fibre sheet with putty and glazing clips in steel
doors, windows, clastery windows all complete.
(a) With 4mm thick glass pans sqm 713.21
(b) With 5.5mm thick glass pans sqm 785.66
(c) With 1mm thick steel sheet i/c 10mm x 10mm x 1.6mm box beading sqm 824.31
(d) With 2mm thick reinforced polymer (FRP) sqm 550.62
2550 Providing and fixing G.I. chain link fabric fencing of required width and mesh size including
strengthening with 2mm dia wire or nuts, bolts and washers as required complete with posts
of specified material and of standard design placed and embedded in cement concrete blocks
45x45x60cm of mix 1:5:10 (1cement :5 sand :10 graded stone aggregate 40mm nominal size)
every 15th post, last but one end post and corner post shall be strutted on both sides and end
post on one side only and struts embedded in cement concrete blocks 70x45x50cm of the
same mix, as per the direction of Engineer- in-charge.
Flooring
2552 Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved
by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4
sand)laid and jointed with grey cement slurry including rubbing and polishing complete with
: (Area of Slabs over 0.50sqm)
2555 Providing and laying rectified glazed Ceramic floor tiles 300 x 300mm or more (having sqm 897.30
thickness 9-10mm) of 1st quality conforming to IS : 15622 of approved make in all
colours, shades, except White, Ivory, Grey, Fume, Red Brown laid on 20mm thick Cement
Mortar 1:4 (1 Cement : 4 sand) including pointing the joints with white cement and matching
pigments etc., complete.
2556 Providing and laying vitrified floor tiles in different sizes with water absorption less than
0.08% and confirming to IS:15622 of approved make in all colours and shades laid on 20mm
thick cement mortar 1:4 (1cement : 4sand) including grouting the joints with white cement
and matching pigments etc., complete.
(a) Size of tile 500X 500 x 9-10 mm sqm 777.60
(b) Size of tile 600X 600 x 9-10mm sqm 804.60
(c ) Size of tile 800 X 800 10-12mm sqm 1306.80
(d) Size of tile 1000 X 1000 10-12mm sqm 1458.00
2557 Add extra in above item for providing and fixing on wall/skirting. Sqm 10 per cent
2558 Deduct for not using 20mm thick cement mortar 1:4 (1cement : 4sand) bedding in laying of sqm 323.10
floors tiles.
2559 Fixing glazed/ Ceramic/Rectified/ Vitrified floor tiles with cement based high polymer sqm 315.00
modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm
thickness.
Page 113 of 132
Code Description Unit Rate
2560 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of sqm 527.40
M-30 grade made by block making machine with strong vibratory compaction and of
approved size and shape laid in required colour and pattern over and including 50 mm thick
compacted bed of course sand filling the joints with sand etc. all complete as per the
direction of engineer in charge.
2561 Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks sqm 631.80
of required strength, thickness and size/shape, made by table vibratory method using PU
mould, laid in required colour and pattern over 50mm thick compacted bed of stone dust,
compacting and proper embedding/laying of inter locking paver blocks into the bedding layer
through vibratory compaction by using plate vibrator, filling the joints with sand and cutting
of paver blocks as per required size and pattern, finishing and sweeping extra sand including
locking edges with M 15 cement concrete in footpath, parks, lawns, drive ways or light
traffic parking etc. complete as per manufacturer's specifications and direction of Engineerin-
Charge. 60mm thick C.C. paver block of M-35 grade with approved colour, design and
pattern.
2562 Providing and laying saw cut 18mm thick mirror polished pre moulded (whereever required)
and pre polished machine cut granite stone of required size and shape of approved shade,
colour and texture in flooring laid over 20mm thick base of cement mortar 1:4 (1 cement :4
sand) including grouting the joints with white cement mixed with maching pigment, epoxy
touch ups etc complete. as per direction of Engineer in charge.
Black
(a) area of slab less than 0.50 sqm Sqm 3129.30
(b) area of slab more than 0.50 sqm Sqm 3348.00
All shades/colour other than black
(a) area of slab less than 0.50 sqm Sqm 3238.20
(b) area of slab more than 0.50 sqm sqm 3325.50
Roofing And Ceiling
2563 Providing & fixing UV stabilized fiberglass reinforced plastic sheet roofing up to any pitch
including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I
plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The
sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3%
Ultra-violet stabilizer in resin system under approximately 2400 psi and hot cured. They shall
be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192
and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or
smooth as specified.
(a) 2mm thick corrugated (2.5" or 4.2" or 6") or step down (2" or 3" or 6" ) as specified. sqm 927.90
(b) 2mm thick flat. sqm 859.50
2564 Providing and fixing on wall face unplasticised Rigid PVC Rain water pipes conforming to
IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm
gap for thermal expansion.
(a) Single socketed pipes
(i) 75 mm diameter (minimum wall thicness 1.8mm) Each 122.40
(ii) 110 mm diameter (minimum wall thicness 2.2mm) Each 214.20
Page 114 of 132
Code Description Unit Rate
2565 Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for
Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including
jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.
(a) Coupler
(i) 75 mm (minimum wall thickness 1.8mm) each 105.30
(ii) 110 mm (minimum wall thickness 2.2mm) each 138.60
(b) Single push fit Coupler :
(i) 75 mm (minimum wall thickness 1.8mm) each 126.00
(ii) 110 mm (minimum wall thickness 2.2mm) each 175.50
(c ) Single tee with door
(i) 75x75x75 mm (minimum wall thickness 1.8mm) each 207.00
(ii) 110x110x110 mm (minimum wall thickness 2.2mm) each 311.40
(d) Single tee without door
(i) 75x75x75 mm (minimum wall thickness 1.8mm) each 180.90
(ii) 110x110x110 mm (minimum wall thickness 2.2mm) each 239.40
(e) Bend 87.5°
(i) 75 mm bend (minimum wall thickness 1.8mm) each 105.30
(ii) 110 mm bend (minimum wall thickness 2.2mm) each 154.80
(f) Shoe (Plain)
(i) 75 mm Shoe (minimum wall thickness 1.8mm) each 157.50
(ii) 110 mm Shoe (minimum wall thickness 2.2mm) each 270.00
2566 Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised -
PVC rain water pipes by means of bombay nail of required length including making good the
wall etc. complete.
(a) 75 mm (minimum wall thickness 1.8mm) each 87.30
(b) 110 mm (minimum wall thickness 2.2mm) each 102.60
2567 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter each 38.70
and weighing not less than 440 grams.
2568 Providing and fixing false ceiling at all height including providing and fixing of frame work
made of special sections, power pressed from M.S. sheets and galvanized with zinc coating
of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25
mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one
flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts
other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with
nuts and bolts of required size and other end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre to which the
ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each
having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction
perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x
230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick
27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to
wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws
@ 230 mm interval, including fixing of 10mm thick plaster of Paris (gypsum anhydrous)
sheet to ceiling section and perimeter channels with the help of dry wall screws of size
3.5x25mm at 230mm interval including jointing and finishing to a flush finish of tapered and
square edges of POP board with jointing compound (POP paste) including the cost of making
openings for light fittings, grills, diffusers cutouts made with frame of perimeter channels
suitably fixed all complete as per drawing, specifications and direction of the Engineer-in-
charge.
(a) Flat surfaces Sqm 608.40
(b) Curved surfaces Sqm 673.20
2569 Extra for any sunk or raised mouldings in the plaster of Paris (Gypsum anhydrous) ceiling Sqm 157.50
2570 Extra for providing plaster of Paris (Gypsum anhydrous) ceiling above 5metres height from Sqm 53.10
floor level.
Page 115 of 132
Code Description Unit Rate
2571 Providing and fixing false ceiling at all height including providing and fixing of frame work
made of special sections, power pressed from M.S. sheets and galvanized with zinc coating
of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25
mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one
flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts
other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with
nuts and bolts of required size and other end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre to which the
ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each
having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction
perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x
230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick
27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to
wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws
@ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter
channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including
jointing and finishing to a flush finish of tapered and square edges of the board with
recommended jointing compound , jointing tapes , finishing with jointing compound in 3
layers covering upto 150 mm or both sides of joint and two coats of primer suitable for
board, all as per manufacturer’s specification and also including the cost of making openings
for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably
fixed, all complete as per drawings, specification and direction of the Engineer in Charge but
excluding the cost of painting with :
(a) 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I. sqm 675.00
(b) 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part sqm 779.40
I. mm thick tapered edge gypsum moisture resistant board.
(c ) 12.5 sqm 828.00
(d) Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. sqm 1509.30
2572 15 %
Providing perforated
and area withboard
fixing insulating perforation
ceilingsize andthick
12 mm pattern
of as approved
approved by thewith
quality Engineer-in-
necessary
nails etc. complete (frame work to be paid separately):
(a) Natural colour insulating board Sqm 495.00
(b) White face insulating board Sqm 552.60
(c ) Flame retardant face insulating board Sqm 552.60
2573 Providing and fixing flat pressed 3 layer medium density particle board or graded particle
board (Grade I) IS: 3087, 12 mm thick marked in ceiling with necessary nails etc. complete
(frame work to be paid separately) :
2574 (a) 12mm thick Sqm 569.70
2575 Providing and fixing plain Multipurpose Cement board 6mm thick ( High Pressure steam
cured ) as per IS : 14862 : 2000 ) with suitable fibre cement screw in ceiling etc. complete
(frame work to be paid separately) :
(a) 6 mm thick cement board sqm 385.20
2576 Extra for Circular cutting and waste in ceiling with:
(a) Natural colour insulating board 12 mm thick metre 135.00
(b) White face insulating board 12 mm thick metre 142.20
(c) Flame retardant face insulating board 12 mm thick metre 142.20
2577 Extra for providing and fixing ceiling to curved surfaces in narrow widths Sqm 90.00
Page 116 of 132
Code Description Unit Rate
2578 Providing and fixing false ceiling with 12 mm thick plain/ semi perforated or with design Sqm 600.30
ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board
conforming to IS:3087 finished with a coat of aluminium primer on both sides & edges and
two coats of synthetic enamel paint of approved quality on exposed face fixed to a grid made
out of anodized aluminium(with 15 micron anodic coating) T-sections 35 x15x1.5 mm size
main runners and cross runners 23.5x19x1.5 mm fixed to main runners placed 600 mm centre
to centre both ways so as to form a grid of 600 mm square. The frame work shall be
suspended from ceiling by level adjusting hangers of 6 mm dia M.S rod fixed to roof slab by
means of ceiling cleats. The suspenders shall be placed 600x 1200 mm centre to centre
including fixing to the frame with C.P brace screws and applying a priming coat of zinc
chromate yellow primer (aluminium frame work shall be paid separately).
2579 Extra for providing 3 mm thick translucent white acrylic plastic sheets of approved quality in Sqm 387.00
false ceiling instead of 12 mm thick plain/or with design particle board ceiling tiles in item
above.
Finishing Work
2580 Providing and applying plaster of paris punning of 10 mm average thickness over plastered sqm 117.00
surface to prepare the surface even and smooth complete
2581 Providing and applying white cement based putty of average thickness 1mm of approved Sqm 66.60
brand and manufacture, like Birla white/J.K. white or equivalent, over yhe plastered wall
surface to prepare the surface even and smooth i/c all cost of material, labour, and scaffold
etc. in all position complete.
2582 Distempering with oil bound washable distemper of approved brand and manufacture to give Sqm 54.00
an even shade.
(a) New work (two or more coats) over and including water thinable priming coat with
2583 cement(ready
Distempering with 1st quality acrylic distemper primer.
mixed) of approved manufacturer, of sqm 30.60
required shade and colour complete, as per manufacturer's specification.
2584 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even Sqm 57.60
shade:
(a) Two or more coats on new work
2585 Finishing walls with textured exterior paint of required shade: Sqm 118.80
New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base coat of
water proofing cement paint applied @2.20 kg/10 sqm.
2586 Finishing walls with Acrylic Smooth exterior paint of required shade:
(a) New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming sqm 78.30
coat of exterior primer applied @ 2.20 kg/ 10 sqm).
2587 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of Sqm 75.60
required shade.
(a) New work (Two or more coats applied @ 1.43 ltr/ 10sqm. over and including base
coat of water proofing cement paint applied @ 2.20 kg/10 sqm).
Page 117 of 132
Code Description Unit Rate
2588 Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using
Primer as per manufacturers specifications :
(a) Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of sqm 72.90
Special primer applied @ 0.75 ltr / 10 sqm.
(b) Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more sqm 62.10
coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm
of approved brand or manufacture
(c ) Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or sqm 63.90
more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/
10 sqm of approved brand or manufacture
(a) White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type Each 2695.50
(b) foot rests. Steel AISI-304(18/8) Orissa pattern W.C. pan of size 585x480 mm with
Stainless Each 6327.90
2591 flushand
Providing pipefixing
and integrated type foot
white vitreous rests.
china pedestal type water closet (European type W.C.
pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe
with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and
fixtures complete including cutting and making good the walls and floors wherever required :
(a) W.C. pan with ISI marked white solid plastic seat and lid Each 2732.40
(b) W.C. pan with ISI marked black solid plastic seat and lid Each 2711.70
2592 Providing and fixing white vitreous china pedestal type water closet (European type) with
seat and lid, 10 litre low level white vitreous china flushing cistern, C.P. flush bend with
fittings, C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard
make and mosquito proof coupling of approved municipal design complete including
painting of fittings and brackets, cutting and making good the walls and floors wherever
required :
(a) W.C. pan with ISI marked white solid plastic seat and lid. Each 4151.70
(b) W.C. pan with ISI marked black solid plastic seat and lid. Each 4131.00
2593 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal
basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing
cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps
complete, including painting of fittings and brackets, cutting and making good the walls and
floors wherever required :
(a) One urinal basin with 5 litre white P.V.C. automatic flushing cistern. Each 2478.60
(b) Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern. Each 4012.20
(c ) Range of three urinal basins with 10litre white P.V.C. automatic flushing cistern. Each 5680.80
(d) Range of four urinal basins with 10 litre white P.V.C. automatic flushing cistern. Each 7545.60
2594 Providing and fixing white vitreous china flat back half stall urinal of size 80x380x350mm
with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe,
spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I.
trap with outlet grating and other couplings in C.P. brass including painting of fittings and
cutting and making good the walls and floors wherever required:
(a) Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. Each 5010.30
Page 118 of 132
Code Description Unit Rate
(b) Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern. Each 7794.00
(c ) Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern. Each 11487.60
(d) Range of four half stall urinals with 10 litre P.V.C. automatic flushing cistern. Each 13992.30
2595 Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40
mm C.P. brass waste complete, including painting the fittings and rackets, cutting and
making good the walls wherever required :
(a) White glazed fire clay kitchen sink of size 600x450x250 mm. each 2242.80
2596 Providing and fixing Stainless Steel ISI 304 (18/8) kitchen sink as per IS 13983 with C.I.
brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting
and making good the walls wherever required :
(a) Kitchen sink with drain board
(i) 510x1040 mm bowl depth 250mm. Each 7266.60
(ii) 510x1040 mm bowl depth 225mm. Each 6848.10
(iii) 510x1040 mm bowl depth 200mm. Each 6743.70
(iv) 510x1040 mm bowl depth 178mm. Each 4757.40
(b) Kitchen sink without drain board
(i) 610x510 mm bowl depth 200 mm. Each 4124.70
(ii) 610x460 mm bowl depth 200 mm. Each 3915.90
(iii) 470x420 mm bowl depth 178 mm. Each 3079.80
2597 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain
with rubber plug 40mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass
unions complete including painting of fittings and brackets, cutting and making good the wall
wherever required
Aluminium Work
25-112 Providing and fixing aluminium work for doors, windows, ventilators and partitions with
extruded built up standard tubular sections/ appropriate Z sections and other sections of
approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required
dia and size including necessary filling up the gaps at junctions, i.e. at top, bottom and sides
with required EPDM rubber/neoprene gaskit etc. Aluminium sections shall be smooth,rust
free, straight, mitred and jointed mechanically wherever required including cleat angle,
Aluminium snap beading for glazing / panneling,C.P. brass / stainless steel screws, all
complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,
paneling and dash fasterners to be paid for separately) :
(iii) Polyester powder coated aluminium (minimum thickness of polyester powder coating kg 344.70
50 micron)
(b) For shutters of doors, windows and ventilators including providing and fixing hinges/
pivots and making provision for fixing of fittings wherever required including the cost of
EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately).
(i) Anodized aluminium (anodized transparent or dyed to required shade according to IS: kg 360.00
1868, Minimum anodic coating of grade AC 15)
(ii) Powder coated aluminium (minimum thickness of powder coating 50 micron) kg 382.50
(iii) Polyester powder coated aluminium (minimum thickness of polyester powder coating kg 387.90
50 micron)
25-113 Providing and fixing 12mm thick Pre-laminated particle board flat pressed three layer or
graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in
aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel
screws etc. complete as per architectural drawings and directions of engineer-in-charge.
(a) Pre-laminated particle board with decorative lamination on one side and balancing sqm 921.60
lamination on other side.
(b) Pre-laminated particle board with decorative lamination on both sides. sqm 965.70
25-114 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions
etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and
the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic
item) :
Page 122 of 132
Code Description Unit Rate
(a) With float glass panes of 4.0 mm thickness sqm 764.10
(b) With float glass panes of 5.50 mm thickness sqm 838.80
(c ) With float glass panes of 8 mm thickness sqm 1162.80
25-115 Add extra for providing and fixing froasted glass instead of float glass
(a) With glass panes of 4.0 mm thickness sqm 233.10
(b) With glass panes of 5.50 mm thickness sqm 235.80
(c ) With glass panes of 8 mm thickness sqm 235.80
25-116 Providing and fixing double action hydraulic floor spring of approved brand and manufacture
conforming to IS : 6315, having brand logo embossed on the body/ plate with double spring
mechisum and door weight upto125 kg, for doors including cast of cutting floors, embedding
in floors as required and making good the same matching to the existing floor finishing and
cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc.
complete as per the direction of Engineer-in-charge.
(a) With stainless steel cover plate- minimum 1.25 mm thickness Each 1810.80
(b) With brass cover plate- minimum 1.25 mm thickness Each 1967.40
25-117 Providing and fixing powder coated aluminium work (minimum thickness of powder coating kg 412.20
50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in
frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless
steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs
@ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm
dia. with necessary cadmium plated machine screws all complete as per approved
architectural drawings and direction of the Engineer-in-charge (level adjusting hangers,
ceiling cleats and expansion hold fasteners to be paid for separately).
25-118 Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length) fixed to Each 119.70
roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60mm long and
expansion hold fasteners 12.5 mm dia. 50mm long complete as per direction of Engineer -in-
charge
25-119 Providing and fixing machine moulded aluminium covering of approved pattern and design,
made out of machine cut aluminium sheet and machine holed for receiving dash fastener,
over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one
side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm
long bolt including providing aluminium washers 2 mm thick and 15 mm dia, at a staggered
pitch of 200mm centre to centre including drilling holes in the receiving surface and
providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-
charge :
(a) Anodised aluminium sheet 2.5mm thick (anodised transparent or dyed to required kg 432.00
shade according to IS: 1868, Minimum anodic coating of grade AC 15)
(b) Powder coated aluminium sheet 2.5mm thick (minimum thickness of powder coating kg 453.60
50 micron)
25-120 Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by metre 73.80
providing weather silicon sealant over backer rod of approved quality as per architectural
drawings and direction of Engineer-in-charge complete.
(a) Upto 5mm depth and 5 mm width
25-121 Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruded
sections.
(a) For fixed portion kg 15.30
(b) For shutters of doors, windows & ventilators. kg 15.30
25-122 Providing and fixing double glazed hermetically sealed glazing in aluminium windows, Sqm 3125.70
ventilators and partition etc. with 6 mm thick clear float glass both side having 12 mm air
gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant
(Both primary and secondary sealant) etc. as per specifications, drawings and direction of
Engineer-incharge complete.
25-123 Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick and 2100
mm long with SS screws etc .complete as per direction of Engineer-in-Charge.
25-124 Providing and fixing 100mm brass locks (best make of approved quality) for aluminium each 438.30
doors including necessary cutting and making good etc. complete.
25-125 Providing and fixing anodized aluminium (anodized transparent or dyed to required shade kg 298.80
according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for
windows and ventilators a with extruded built up standard tubular sections of approved make
conforming to IS: 733 and IS : 1285 fixed with crawl plugs and stainless steel screws etc.
25-126 Providing and fixing aluminium casement windows fastener of required length for aluminium
windows with necessary screws etc. complete.
25-129 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand sqm 4462.20
and manufacture, including providing and fixing top bottom pivot spring type fixing
arrangement and making necessary holes etc. for fixing required door fittings, all complete as
per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).
25-130 Providing and fixing 50 micron thick reflective one way type heat /light control film to sqm 403.20
window/door glazing as marketed under the brand name garware/3M or equivalent as
approved.
25-131 Providing and fixing 50 micron thick Frosted heat /light control film to window/door glazing sqm 466.20
as marketed under the brand name garware/3M or equivalent as approved.
25-132 Providing and fixing 25 micron thick Non reflective heat /light control film to window/door sqm 316.80
glazing as marketed under the brand name garware/3M or equivalent as approved.
Page 124 of 132
Code Description Unit Rate
Water Proofing Work
25-133 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by sqm 186.30
applying cement slurry mixed with water proofing cement compound consisting of applying :
a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement
compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours.
b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement
compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with
water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of
all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
25-134 Providing and laying water proofing treatment on roofs of slabs by applying cement slurry sqm 304.20
mixed with water proofing cement compound consisting of applying (a) after surface
preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing
cement compound @ 0.253 kg/sqm. b) laying second layer of Fibre glass cloth when the first
layer is still green.Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third
layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water
proofing cement compound @ 0.670 kg/sqm and sand @ 1.289 kg/sqm. This will be allowed
to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be
taken upto 30cm on parapet wall and tucked into groove in parapet all around.
25-136 Supplying and stacking sludge at site including royalty and carriage (sludge measured in cum 643.50
stacks will be reduced by 8% for payment).
25-137 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of cum 16.20
officer incharge (Cost of sludge, dump manure or/ and good earth to be paid separately).
25-138 Mixing earth and sludge or manure in the required proportion specified or directed by the cum 10.80
officer incharge.
25-139 Grassing with selected type of grass including watering and maintenance of the lawn for 30 100sqm
days or more till the grass forms a thick lawn, free from weeds and fit for mowing including
supplying good earth, if needed (the good earth shall be paid for separately):
25-141 Preparation of beds for hedging and shrubbery by excavating further 30cm deep of allready cum 67.50
prepared trench, refilling the excavated earth after breaking clods and mixing with sludge
or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one
part of stacked volume of sludge or manure after reduction by 8%), flooding with water,
filling with earth if necessary, watering and finally fine dressing, leveling etc.including
stacking and disposal of materials declared unserviceable and surplus earth by spreading and
leveling as directed, within a lead of 50m lift up to 1.5 m complete (cost of sludge, manure or
extra earth to be paid for separately).
Page 125 of 132
Code Description Unit Rate
25-142 Providing and fixing M. S. tree guard 50 cm square in plan, height 1.40 metre above ground each 2244.60
level and 0.50 metre below ground level. The vertical members shall consist of four nos. of
angle iron of size 25x25x5 mm 1.9 long, one at each corner and 8 nos. flat iron of size 25x5
mm 1.4 long. The vertical members shall be welded to 4 nos. 25x6 mm M. S. flats placed
horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S.
sheet of size 250x100 mm shall be welded to the tree guard near the middle height and
lettered PWD/ any other approved name. The tree guard shall be fixed to the ground by
making suitable holes and by embedding four corners leg in the ground , including refilling
the earth, compaction etc. complete. The tree guard shall be painted with two coats of paint
of approved brand and manufacture over a coat of primer, complete in all respect.
25-144 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions
etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and
the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic
item) :
SECTION-B (WRD)
25-145 Providing and fixing 25 mm dia. 3 m long cold twisted deformed steel dowel bars with one each 868.00
end driven into 38 mm diameter 1.50 m deep hole drilled in bed rock and other end provided
with L- bend for embedding in concrete / masonry of over flow / non-over flow blocks and
other appurtenant works including cost of all materials, machinery, labour, drilling and
cleaning hole, filling hole with specified cement mortar, driving anchor rod etc. Complete.
25-146 Drilling 35 to 40 mm diameter grout holesin concrete / rock by percussion drilling using jack mt 327.00
25-147 Providing and fixing fine chisel dressed canal bed grade stone (Type design 5) embedding 45
cm depth of stone with 15 cm concrete all around & in bottom in cement concrete M-7.5
(Nominal Mix), grade including excavation (all type of soil) orientation of stone along centre
line and top of concrete is flushed with design bed level, curing etc. Complete. Using graded
aggregate of maximum size 40 mm.
25-184 Supplying, fitting and fixing in position true to line and level cucm 0.51
elastomeric bearing conforming to IRC:83 (Part-II) Section IX
complete, including all accessories as per drawings and technical
specification Clause 1207.1
25-185 Providing pressure relief pipes 100 mm dia in bottom slab of box Nos. 466
Page 132 of 132