Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
F = Ma (3.1)
The airplane shown in Fig. 3.2 is moving forward after landing, and has a breaking force F applied to
the right. The acceleration is to the right, and the inertia force on each element of mass is to the left, or opposite
to the direction of acceleration. The sum of the inertia forces on all elements will be the product of the total
mass of the airplane and acceleration, or Ma. Since the inertia forces are distributed in proportion to the mass
dM of each element, the resultant force will act at the center of gravity as shown in Fig 3.2. If some part of the
airplane is considered as a free body, it is necessary to obtain the inertia force acting on that part. The inertia
force on any part, will be the product of its mass and the acceleration and will act at the center of the gravity of
that part of the structure.
While the motion of the airplane is not within the scope of a book on aircraft structures, it is
occasionally necessary to consider the motion in order to estimate the duration or the magnitude of loads. The
velocity v is defined as the time rate of change of the displacement s.
v = ds (3.3)
dt
a = dv (3.4)
dt
a = d2s (3.5)
dt2
dv
a=v (3.6)
ds
2/9
Technical Assignment No. 11 Inertial Loads and Load Factor
For a motion of pure translation of a rigid body, all elements of the body must have the same
displacement, velocity, and acceleration. If the acceleration is constant, the following equations are obtained by
integrating Eqs 3.4 to 3.6:
Where s is the distance moved in time t, vo, is the initial velocity, and v is the final velocity after t
seconds.
Assume that the airplane shown weighs 20000lb, and that the braking force F is 8000lb.
a. Find the wheel reactions R1 and R2
b. Find the landing run if the airplane lands at 100mph (146.7 ft/sec)
Solution:
a. + ΣFx = 0
8000lb – Ma = 0
Ma = 8000 lb.
+ ΣMR2 = 0
120R1 – 8000lb(50) – 20000lb(20) = 0
R1 = 8000lb(50) – 20000lb(20)
120
R1 = 6,670 lb.
3/9
Technical Assignment No. 11 Inertial Loads and Load Factor
+ ΣFy = 0
6670lb – 20000 – R2 = 0
R2 = 13,330 lb.
b. a = F
M
M=W
g
a = Fg
W
= (8000lb)(32.2ft/sec2)
20000lb
a = -12.88 ft/sec2
From eq 3.9
v2 – vo2 = 2as
0 – (146.7ft/sec)2 = 2(-12.88 ft/sec2)s
s = 835ft.
The 8000lb. airplane shown in Fig. 3.9 is landing on soft ground with an upward acceleration, a y, of
3.5g and an aft acceleration, ax, of 1.5 g. Find the wheel reactions A and B, assuming them to be parallel.
4/9
Technical Assignment No. 11 Inertial Loads and Load Factor
∑ M B=0
A y =8,600lb .
∑ F y =0
¿ 8,600 lb .−36,000lb+ B y
B y =27,400 lb .
1
A x = (8,600 lb)
3
A x =2,870lb
1
B x = (27,400 lb)
3
B x =9,130lb
5/9
Technical Assignment No. 11 Inertial Loads and Load Factor
A 30,000-lb airplane is shown in Fig. 3.8(a) at the time of landing impact, when the ground
reaction on each main wheel is 45,000 lb.
a. If one wheel and tire weighs 500 lb, find the compression C and bending moment m in the oleo strut,
if the strut is vertical and is 6 in. from the center line of the wheel, as shown in Fig. 3.8(b)
b. Find the shear and bending moment at section AA of the wing, if the wing outboard of this section
weighs 1,500 lb and has its center of gravity 120 in. outboard of section AA.
c. Find the required shock strut deflection if the airplane strikes the ground with a vertical velocity of
12ft/sec and has a constant vertical deceleration until the vertical velocity is zero. This neglects the energy
absorbed by the tire deflection, which may be large in some cases.
d. Find the time required for the vertical velocity to become zero.
6/9
Technical Assignment No. 11 Inertial Loads and Load Factor
Solution:
a.) + ΣFy = 0
ΣFy = 45,000lb + 45,000lb – 30,000lb – Ma
Ma = 45,000lb + 45,000lb – 30,000lb
Ma = 60,000 lb.
60,000 lb W
a= ; M=
M g
60,000 lb
a=
W
g
60,000 lb (g)
a=
W
60,000 lb (g)
a=
30,000 lb
a=2 g
Considering the landing gear as a free body, as shown in Fig. 3.8 (b), the inertia force is
W1
M1 a = a
g
500 lb
M1 a = (2 g)
g
M1a = 1,000 lb
ΣFy = 0
C = 43,500 lb
m = 261,000 lb-in
7/9
W2
b.) M2a = a
g
1,500 lb
M2a = g
(2g )
M2a = 3,000 lb
ΣFy = 0
ΣFy = V – 3,000 lb – 1,500 lb
V = 3,000 lb + 1,500 lb
V = 4,500 lb
c.) The shock strut deflection is found by assuming a constant vertical acceleration of -2g, or
-64.4ft/sec2, from an initial velocity of 12ft/sec to a final zero vertical velocity.
a = −2 g ; g = 32.2 ft/ s 2
a = −2 (32.2ft/ s 2 )
a = −64.4 ft/ s 2
2 2
v −v o = 2as
s=1.12 ft
d.) v −v 0 = at
(0)−(12 ft /s )
t=
(−64.4 ft /s2 )
t=0.186 s
8/9
Load Factors for Transitional Acceleration. For flight or landing conditions in which the airplane has
only transitional acceleration, every part of the airplane is acted upon by parallel inertia forces which are
proportional to the weight of the part. For purposes of analysis it is convenient to combine these inertia foreces
with the forces of gravity multiplying the weight of each part by a load factor n. When the airplane is being
accelerated upward, the weight and inertia forces add directly. The weight w of any part and the inertia forces
wa/g have a sum nw.
a
nw=w+ w
g
Or
a
n=1+
g
The combined inertia and gravity forces are considered in the analysis in the same manner as weights
which are multiplied by the load factor n.
In the case of an airplane in flight with no horizontal acceleration, as shown in Fig 3.23, the propeller
thrust is equalto airplane drag, and the horizontal components of the inertia and gravity forces are zero.
The weight and the inertia force on the airplane act down and will be equal to the lift. The airplane lift L
is the resultant of the wing and tail lift forces. The load factor is defined as follows:
lift
Load Factor=
weight
or
L
n=
W
9/9