Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
DTC Check
Using SUZUKI scan tool
1) Turn ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector (DLC) (1)
located on underside of instrument panel.
Special tool
1
(A) : SUZUKI scan tool
(A)
NOTE:
• The distance between the sensor and lamp should be
approximately 100 mm (3.94 in.).
• DTC B1504 is detected even if sensor is normal if sun-
load sensor is not lighted over with an incandescent
lamp.
NOTE:
In case of malfunction of temperature selector, blower
speed selector and air flow selector, the following proce-
dure can not be used. However, SUZUKI scan tool can be
used to check DTCs.
DTC Clearance
Using SUZUKI scan tool
1) Turn ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector (DLC) (1).
Special tool
1 (A) : SUZUKI scan tool
(A)
DTC Table
CAUTION:
Be sure to perform “Air Conditioning System Check” in this section before starting diagnosis.
DTC No. DTC
A/C indicator
(displayed on (indicated
Priority lamp flashing Diagnosis
SUZUKI scan by A/C indi-
pattern
tool) cator lamp)
Outside Air Temperature Sensor and
*B1501 01 1
Its Circuit Malfunction
Inside Air Temperature Sensor and
*B1502 02 2
Its Circuit Malfunction
A/C Evaporator Temperature Sensor
B1503 03 3
and Its Circuit Malfunction
Sunload Sensor and Its Circuit Mal-
*B1504 04 12
function
Engine Coolant Temperature (ECT)
B1510 10 4
Sensor and Its Circuit Malfunction Diagnose
Temperature Control Actuator (Posi- trouble
B1511 11 5 tion Sensor) and Its Circuit Malfunc- according to
tion “Diagnostic
Air Flow Control Actuator (Position Flow” corre-
B1512 12 6
Sensor) and Its Circuit Malfunction sponding to
Temperature Control Actuator and each DTC.
B1513 13 7
Its Circuit Malfunction
Air Flow Control Actuator and Its Cir-
B1514 14 8
cuit Malfunction
Temperature Selector and Its Circuit
B1520 20 9
Malfunction
Blower Speed Selector and Its Cir-
B1521 21 10
cuit Malfunction
Air Flow Selector and Its Circuit Mal-
B1522 22 11
function
– – – Normal –
NOTE:
• Item with asterisk (*) in “DTC No.” column is for vehicles with automatic air conditioning system.
• If no malfunction is detected, A/C indicator lamp and REC indicator lamp flash simultaneously.
AIR CONDITIONING (OPTIONAL) (OTHER THAN CANVAS TOP MODEL) 1B-43
Example
B1502 (No.02)
(a)
(b)
B1512 (No.12)
(a)
(b)
B1522 (No.22)
(a)
(b)
(c)
[A]
(a)
(b)
(c)
Fail-Safe Table
When any of the following malfunctions (DTCs) is detected, HVAC control module enters fail-safe mode.
However, when HVAC control module detects normal operation of A/C system, fail-safe mode is canceled.
Fail-Safe Operation
When ignition switch is
DTC No. Trouble Area When malfunction is detected
turned ON after malfunction
during ignition switch is ON
is already detected
HVAC control module keeps condi-
Outside air temperature
*B1501 20°C (68°F) tion just before malfunction is
sensor and its circuit
detected.
HVAC control module keeps condi-
Inside air temperature sen-
*B1502 25°C (77°F) tion just before malfunction is
sor and its circuit
detected.
HVAC control module keeps condi-
A/C evaporator tempera-
B1503 0°C (32°F) tion just before malfunction is
ture sensor and its circuit
detected.
1B-44 AIR CONDITIONING (OPTIONAL) (OTHER THAN CANVAS TOP MODEL)
Fail-Safe Operation
When ignition switch is
DTC No. Trouble Area When malfunction is detected
turned ON after malfunction
during ignition switch is ON
is already detected
HVAC control module keeps condi-
Sunload sensor and its cir-
*B1504 0 W/m2 tion just before malfunction is
cuit
detected.
HVAC control module keeps condi-
Engine coolant tempera-
B1510 80°C (176°F) tion just before malfunction is
ture sensor and its circuit
detected.
Temperature control actua- HVAC control module stops the
HVAC control module stops the
B1511 tor (position sensor) and its operation of actuator after 1
operation of actuator after 1 minute.
circuit minute.
Air flow control actuator HVAC control module stops the
HVAC control module stops the
B1512 (position sensor) and its cir- operation of actuator after 1
operation of actuator after 1 minute.
cuit minute.
HVAC control module stops the
Temperature control actua- HVAC control module stops the
B1513 operation of actuator after 1
tor and its circuit operation of actuator after 1 minute.
minute.
HVAC control module stops the
Air flow control actuator and HVAC control module stops the
B1514 operation of actuator after 1
its circuit operation of actuator after 1 minute.
minute.
HVAC control module keeps condi-
Temperature selector and
B1520 25°C (77°F) tion just before malfunction is
its circuit
detected.
HVAC control module keeps condi-
Blower speed selector and
B1521 OFF tion just before malfunction is
its circuit
detected.
HVAC control module keeps condi-
Air flow selector and its cir-
B1522 DEF tion just before malfunction is
cuit
detected.
NOTE:
Item with asterisk (*) in “DTC No.” column is for vehicle with automatic air conditioning system.
NOTE1:
This data is for vehicle with automatic air conditioning system.
NOTE2:
This data is for vehicle with manual air conditioning system.
OUTSIDE AIR TEMPERATURE (for vehicle with automatic air conditioning model)
Outside air temperature detected by outside air temperature sensor installed on 4WD air pump assembly
bracket
EVAPORATOR TEMP
Temperature of air passed through evaporator
COOLANT TEMP
Engine coolant temperature detected by engine coolant temperature sensor