Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
H-2000-2246-05-A
MP700 probe with OMM (optical module machine) + MI 12 Mounting Signal strength
35° or 70° output or bracket To assist finding the
O-M-I (optical machine interface) optimum position for the
Vertical
2. Optical-on – Timer-out
A timer automatically returns the probe to stand-by if
the probe has not been used for 33 seconds or 134
seconds.
Performance envelope
The MP700 has transmission envelope over the ranges shown Natural reflective surfaces within the machine may increase
below. the signal transmission range.
The probe system should be positioned such that the optimum Coolant residue accumulating on the OMP LEDs and OMM/
range can be achieved over the full travel of the machine axis. O-M-I window, will have a detrimental effect on transmission
performance.
The OMP and OMM/O-M-I may deviate from the optical
centre line, provided opposing light cones always overlap with Wipe clean as often as is necessary to maintain unrestricted
transmitters and receivers mutually in each others field of view transmission.
(eye to eye).
MP700 35° output probe with OMM MP700 35° output probe with O-M-I
Range m (ft)
60° OMM Range m (ft) O-M-I
Switch on/off
Switch on/off
45° 60°
Operating
Operating
1( 45°
30° 3.3
2( )
6.5 30° 1(
3( ) 3.3
15° 9.8 )
4( ) 15° 2(
6.5
13 )
0° .1 0°
Optical centre line 5( ) 3(
16
.4 Optical centre line 15° 9.8
15° 6( ) 30° 45° 60° )
30° 19
45° 60° .6)
60° 45°
75° 30°
90°
15°
.6)
19 75° 60° 45° 30°
6( )
.4 90° 15°
5 (16 0°
.1 ) 8) 0°
(13 3 (9.
4 ) 15° )
9.8 6.5 15°
3( ) 2( )
6.5 (3.
3
2( 30° 1
30°
3. 3)
1(
35° OMP 35° OMP
MP700 70° output probe with OMM MP700 70° output probe with O-M-I
Range m (ft) 60° OMM Range m (ft)
Switch on/off Switch on/off O-M-I
45°
Operating 1( Operating
30° 3.3
2( ) 60° 1 (3.3)
6.5
3( ) 2 (6.5)
15° 9.8 45°
4( ) 3 (9.8)
13
0°
5( )
.1 30°
Optical centre line 16 60°
.4 15° 45°
15° 6( ) 0°
30° 19 15° 30°
45° 60° .6)
15° Optical centre line
30° 0°
45°
15°
60°
30° 15° 0°
30° 45° 15°
75° 60°
30°
45° 75°
90° 45°
90°
6)
)
9.8
9.
4)
60° ( ) 60°
(1
1)
6.5
6.
3 )
2(
3.
)
(1
6
3.3
.8
(1
1 .5)
1(
(9
5
)
.3
4
(6
3
(3
2
Dimensions
Alternative probe outputs
70° or 35°
Optical signal Translational
transmitters on-centre adjustment
70° with adjusting plate
Ø62 (2.44) V Flange taper shank to
(recommended)
35° suit machine
X/Y overtravel (available from Renishaw)
16.5°
16.5°
Ø6
(0.24) Pull stud
Z overtravel
Dimension A (not supplied by Renishaw)
11 (0.43) 35° output shown
24.5 see
Stylus up to Data Sheet
(0.96)
200 (7.87) 70° 46.4 (1.82) 70° 69.8 (2.75) Taper Shanks
A
long 35° 48.8 (1.92) 35° 67.9 (2.67) H-2000-2011
GAUGE LINE
Stylus overtravel limits
Stylus length X Y Z
50 (1.97) 21.5 (0.84) 21.5 (0.84) 11 (0.43)
100 (3.94) 36.0 (1.42) 36.0 (1.42) 11 (0.43) dimensions mm (in)
Specification
Primary application Inspection probe for machining centres
Operating range Up to 6 m (19.6 ft)
Weight 730 g (26.0 oz)
Sense directions 5-way
Repeatability, maximum 0.25 µm (10 µin) - 50 mm stylus length*
2s value in any direction 0.35 µm (14 µin) - 100 mm stylus length*
X/Y 2D pre-travel variation 0.25 µm (10 µin) - 50 mm stylus length*
0.25 µm (10 µin) - 100 mm stylus length*
X/Y/Z 3D measuring performance 1.00 µm (40 µin) - 50 mm stylus length*
(Variation from a true sphere) 1.75 µm (70 µin) - 100 mm stylus length*
Trigger speed range 30 mm/min (1.18 in/min) to 500 mm/min (19.68 in/min)
Stylus trigger force
XY plane 0.19 N, 19 gf, (0.68 ozf) typical §
+Z direction 3.25 N, 325 gf, (11.69 ozf) typical §
Stylus overtravel force
XY plane 1.8 N, 180 gf, (6.47 ozf) typical maximum†
+Z direction 14 N, 1400 gf, (50.36 ozf) typical maximum†
Stylus overtravel
XY plane 16.5°
+Z direction 11 mm (0.43 in)
Sealing IP68 (BS 5490, IEC 529) 1 atmosphere
Maximum recommended stylus length 200 mm (7.87 in)
Maximum number of triggers per second 3
* The specification applies to a test rig gauging speed of 240 mm/min (9.45 in/min) with zero time delay.
§ Performance specification is for a test velocity of 30 mm/min (1.18 in/min) with a 50 mm stylus and with the trigger filter
delay set to 8 ms.
† Performance specification is with a 50 mm stylus.
Battery life
Parts list
Please quote the part number when ordering equipment
*H-2000-2246-05*
main web site at www.renishaw.com/contact
© 2008 Renishaw plc. All rights reserved. Renishaw reserves the right to change specifications without notice Issued 05.08 Part no. H-2000-2246-05-A