Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
▣Features
lMax. display : 1999
lAuto Zero function and Hold function
l7Segment LED Display
lCase size by DIN specification
▣Ordering information
◎ DC VOLT METER / DC AMPERE METER
M 4 N D V 0 1
DC Voltage INPUT FU S DC Current INPUT FU S
1 199.9mV 199.9μA
2 1.999V 1.999mA
Measuring input
3 19.99V 19.99mA
4 199.9V 199.9mA
X Option Option
V Volt Meter
A Ampere Meter
D Measuring DC type
4 3½digit
M Meter
M 4 N D I 0 X
X Option
Power supply 0 5VDC
1 12-24VDC
Measuring input
I 4-20mADC (1-5VDC : Option)
Measuring input type
D Measuring DC type
4 3½digit
M Meter
E-7
Miniature DC Input Type
▣Specifications
(A)
Counter
Model M4N-DV- M4N-DA- M4N-DI-
Mechanical 0.75mm amplitude at frequency of 10 ~ 55Hz in each of X, Y, Z directions for 1hour (G)
Vibration Display
Malfunction 0.5mm amplitude at frquency of 10 ~ 55Hz in each of X, Y, Z directions for 10minutes unit
(J)
Photo
electric
▣Connections sensor
(K)
Pressur
sensor
CONNECTI ON DIAGRAM
SOURCE
5V DC 2W
POWER IN PUT
INPUT
+-
(L)
1 2 3 4 5 6 7 8 10 Rotary
LO HI
HOLD encoder
MADE IN KOREA 2A059B
1 2 3 4 5 6 7 8 9 10
LOW HIGH (M)
5-Phase
stepping
HOLD m otor &
Dr iver &
Controlle
※Socket pin 9, NC terminal, is not connected to internal circuit.
※Socket Pin NO : 1 2 3 4 5 6 7 8 9 10
E-8
M4N Series
▣Dimensions
48 63 Min. 60
4 37 22
+0.5
21.5 -0
Min. 37
45.5 +0.5
-0
63
19
Unit:mm
▣Connections
◎DC voltmeter connection ◎DC Ampere connection
I
Hi Hi
+ +
V1 Load M4N P ower supply V M4N Power supply
- -
Low
Load Low
+ +
V1 Load V2 R2 M4N Power supply V Shunt M4N P ower supply
- -
Low
Load Low
R2
V2 = × V1 R1 〉R2
R1+R2
E-9
Miniature DC Input Type
▣Proper usage
◎Caution for selecting and using products (A)
Counter
lBefore you buy or use the Panel Meter, please lIndicating method of unit
read this catalog. The product, which is produced M4N is not indicated a unit on the product, therefore
by customer's requirement, cannot be exchanged. please indicate it in panel. (B)
Timer
lWhen providing the power, it could display arbitrary
Panel
number. It is because measuring input terminal is
V Indicat ing unit
opened. If connecting Low terminal of measuring
(C)
input to GND, it displays "000". Temp.
controlle
M4N
lIf it indicates 1 or -1 during input signal is ON,
please turn OFF the power and check the connection lIndicating method of decimal point
The indicating decimal point is set in the product
condition. (D)
by your order. Power
It is because the input signal is too low or high. controlle
(The prior products indicate the decimal point by
lWhen measuring voltage is higher than 200VDC,
using jump line in external connector like as
please divide the voltage with multiplying resistance
connection figures.) (E)
to make lower than 200VDC. Panel
After buying the product do not change the decimal meter
(Refer the connection method of DC voltmeter in point. If you need to change it, please connect to
the application of connections) our A/S center or appropriate agency. (F)
Ex)Measuring 1000VDC Tacho/
Speed/
As above connection figure of DC voltmeter, ◎Caution for connecting M4N Pulse
select the R1 value to make 200VDC on R2. lIn case of using both voltmeter and ampere meter meter
(Generally R1 value will be higher than R2 Because the connection of measurement input
(G)
value.) terminal and power terminal is not insulated, Display
Order the D.P.M indicating 1000V for 300VDC. when you use voltmeter and ampere meter by unit
E-10