Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Easergy range
Flair 22D
CT1 59925 CTR2200 Phase CT for RM6 cubicle bushing
bb CTR2200/CTRH2200: mounting without
59926 CTRH2200 Zero sequence CT (split toroidal core)
common point 6 wires (type A or B) CT2 59963 MF1 Phase CT for cable (split toroidal core)
bb MF1: mounting with or without 59962 MF1 bundle CT connector cable for 4-wire mounting (A or B
common point 4 wires (type A or B) or MFH type)
DB415004
User’s
EMS58423 CAB-EXT-2M- VPIS-VO extended cable connection 2m
VPIS
manual
22D
Flair
6-wire mounting
Connection to Flair 22D
Type A Type B
NT0023109 CTR2200 CTR2200 and
CTs CTRH2200 CTs L0/L1 L2 L3 Reset BVE OUT
L1 or L0
1 2 3 4 5 6 7 8 9 10 11 12 BVE option:
External
TO
T
NOTE
U
brown
P
A
SCADA
H
CTR CTRH
output indicator unit
Flair 22D VPIS-VO input is compatible with blue
VPIS V2 only (not compatible with VPIS V3). L2 brown
Differentiating visually a VPIS V2 and VPIS V3 CTR CTR
is easy: blue Common
point
A VPIS V2 has a black seal in its front face. L3 brown
Test
Reset
A VPIS V3 has a green seal in its front face. CTR CTR
blue
I max
. Earthing connection or
is authorized
A 4-wire mounting 4-wire mounting
L1 Easer
gy
MF1 MF1
L2 Flair
22D S1/3IO S1 S1 S2 S1 S1 S1/3IO S2
L3 Esc 8352 grey grey L1
EMS5
MFH
L3 blue L0
blue
MF1
MF1 MF1
brown
blue brown
L2 L2
blue
MF1 MF1
brown black black
L0 MFH L3
blue blue
blue
59998 59997 59962
Type B type B type B type A & B Type A Type B
MF1 and MFH CTs MF1 CTs MF1 and MFH CTs
Schneider Electric
35 rue Joseph Monier As standards, specifications and designs change from time to time,
92500 Rueil Malmaison - France always ask for confirmation of the information given in this publication.
Phone: +33 (0)1 41 29 70 00
www.schneider-electric.com
Publication : Schneider Electric Made in France
© 2013-2018 Schneider Electric. All Rights Production : Schneider Electric This document was printed on
Reserved. Printing : Schneider Electric environmentally friendly paper
NT00231-FR-EN-09 12-2018
Parameters setup
Operation Flair 22D is a fault passage indicator without settings
DE58715
Test
Reset
A lamp measurements.
DE58717
L2 I max.
powered by the measurement sensors. L3
It incorporates a lithium battery to ensure However, it is possible to perform specific override settings.
continuity of operation when the current Test /Reset 22D These settings are made using the 3 buttons located under
Flair
Esc
Easergy
is less than 2 A. Flair 22D
the display.
Maximeter
EMS58352
Low Power mode : if I ≤ 3 A without VPIS-VO option: fault detection is disable. scrolling sequence
with VPIS-VO option : fault detection is enable (only with resistive or
direct to the earth neutral system [EN]). Zero sequence threshold CTs type A (°) to 05 to 30 A (5 A increments)
or
“I0 >” (Earth Fault) (A) 30 to 200 A (10 A increments) or
bb Maximeter mode CTs type B to 05 (*) to 30 A (5 A increments) (+)
30 to 200 A (10 A increments)
or or
To access the maximeter function, press once the “Imax.” button. Imax threshold “I >”
For each phase, an indication of the maximum load currents since the last reset is displayed. to or (¤) (50 A increments) or
(OverCurrent) (A)
Example for a max. current of 500 A in phase 1: then , followed by M2 and M3. Type of neutral EN: resistive neutral or direct to the earth
or or
The maximeters scroll only once. system IN: isolated neutral / CN : compensated neutral
All the maximeter values are reset by pressing on the “Test/Reset” button during scrolling. CT mounting
When Flair 22D is provided with an earth CT (B type mounting), display of M2 and M3 only. or
Phase CTs ; Earth CT
CT type
Detector in fault indication or
bb Event A: the current exceeds one of the thresholds set for a period ≥ acknowledge time.
bb Event B: the line current disappears (or absence of U with VPIS-VO option). Acknowledge time or to 40 to 100 ms (20 ms increments)
(Fault duration) (ms) 100 to 300 ms (50 ms increments)
Fault indication is active when A is followed by B within a lapse of time of less than “VAL” delay. Inrush (s) or or
bb Phase-to-earth fault detected: display of or or (or if earth CT
or [IN] or [CN] neutral system mode), the indicator lamp flashes (1 flash every 3 s) and the output contact Automatic reset (s) or or
is activated.
Fault VALidation (s) or or
bb Phase-to-phase fault detected: display of (Overcurrent),
the indicator lamp flashes (2 flashes every 6 s) and the output contact is activated.
timer reset (h) to or or or or or
For these 2 types of faults, the indicator lamp flashes until it is reset (Reset), which can be achieved by:
vv current recovery > “Ar” delay, configurable time delay (Reset active if “Automatic reset” is not on OFF) Network frequency
vv U recovery, if VPIS-VO option (Reset active if “Automatic reset” is not on OFF) or or
vv end of the time delay, configurable (Timer reset) 60 s V Ammeter mode
DE59155
vv a press on external Reset Note: Fd setting value is 60 ms and cannot be modified while EF or OC threshold are on Auto mode.
vv manual actuation of the “Test/Reset” button. (*) 5 A with CTs CTRH2200 only.
(°) : 20A mini for resistive neutral [EN], 5A mini for isolated [IN] or compensated neutral [CN].
Maintenance (+) : The AUTO mode is only available for isolated or compensated neutral.
(¤) : The AUTO mode is only available in 3 phases mounting
bb The lithium battery of the Flair 22D indicator should be changed about every 15 years.
Gestion des réseaux électriques MT Raccordement des tores Références
sur les 3 câbles MT Type Réf. Produit Description
bb Section : max. 1,5 mm2 EMS58352 Flair 22D Détecteur de défaut
Gamme Easergy bb CTR2200/CTRH2200 : montage sans CT1 59925 CTR2200 Capteur courant de phase
Flair 22D
pour bushing de cellule RM6
point commun 6 fils (type A ou B) 59926 CTRH2200 Capteur courant homopolaire ouvrant
bb MF1/MFH : montage avec ou sans CT2 59963 MF1 Capteur courant de phase pour câble (ouvrant)
point commun 4 fils (type A ou B) 59962 Faisceau Câble liaison tores pour montage 4 fils (type A ou B)
d Important : MF1 ou MFH
bb Monter les tores dans le bon sens : 59927 MFH2200 Capteur courant homopolaire ouvrant
vv Pour les tores ouvrants MF1/MFH2200 : 59988 BVE Voyant extérieur
Connecteur câble tores vers le bas 59961 BVD Voyant anti-vandalisme
Indicateurs de passage de courant de défaut vv Pour les tores fermés CTR2200 : 59967 LED Voyant encastrable
Côté rouge du tore face au jeu de
phase-phase et/ou phase-terre à réglage automatique
59965 BAT 279 Pile au lithium
barres (bushing) 59998 IC30C Cable 3m pour MFH2200
pour tout type de régime de neutre bb Repasser la tresse de masse de l’écran 59997 Faisceau
MF1 ou MFH
Câble liaison tores pour montage 4 fils
(type B)
du câble MT à l’intérieur du tore.
Double alimentation : autoalimenté + pile lithium EMS58422 CAB-EXT-1M- Rallonge cable liaison VPIS-VO longueur 1m
VPIS
DB415004
EMS58423 CAB-EXT-2M- Rallonge cable liaison VPIS-VO longueur 2m
Manuel
VPIS
utilisateur
22D
Flair
TO
T
U
marron
P
A
H
NOTE CTR CTRH Sortie
SCADA Extérieur
bleu
L’entrée VPIS-VO du Flair 22D est compatible
uniquement avec le VPIS V2 (il n’est pas L2 marron
compatible avec le VPIS V3). CTR CTR
bleu
Différentier visuellement un VPIS V2 d’un Point
commun
VPIS V3 est facile : L3 marron
CTR
Test
Reset
Le VPIS V2 inclue un joint noir en face avant. CTR
bleu
Le VPIS V3 inclue un joint vert en face avant.
Raccordement ou
.
I max
à la terre possible
A Montages 4 fils Montages 4 fils
L1 gy MF1 MF1
Easer S1/3IO S1 S1 S2 S1 S1 S1/3IO S2
L2 22D
Flair gris gris L1
L3 Esc 8352
EMS5
L3 MFH
bleu L0
bleu
MF1
MF1 MF1
marron
bleu marron
L2 L2
bleu
MF1 MF1
marron noir noir
L0 MFH L3
bleu bleu
bleu
59998 59997 59962
Type B Type A Type B
type B type B type A & B
tores MF1 et MFH tores MF1 tores MF1 et MFH
Schneider Electric
35 rue Joseph Monier En raison de l’évolution des normes et du matériel, les caractéristiques
92500 Rueil Malmaison - France indiquées par les textes et les images de ce document ne nous engagent
Tél. : +33 (0)1 41 29 70 00 qu’après confirmation par nos services.
www.schneider-electric.com
Publication : Schneider Electric Made in France
© 2013-2018 Schneider Electric. Tous droits Production : Schneider Electric Ce document a été imprimé
réservés Impression : Schneider Electric sur du papier écologique
NT00231-FR-EN-09 12-2018
Fonctionnement Paramétrage
DE58715
Test
Reset