Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Ersin ERDALI 1
Standard applications
for 220 kVA – 2500 kVA
Ersin ERDALI 2
DSE 7320 are new control modules for single gen-set applications.
The module has been designed to start and stop diesel and gas
generating sets that include electronic and non-electronic engines.
Ersin ERDALI 3
Instrumentation, event log and
configuration screens buttons
Transfer switch buttons
and mimic diagram
Horn mute
and lamp test
Ersin ERDALI 4
PC CONNECTIONS
Ersin ERDALI 5
Viewing The Event Log :
The event log only includes shutdown and electrical trip alarms logged;
The event log does not save warning alarms
Ersin ERDALI 6
Rear Panel Output Connections :
Ersin ERDALI 7
Electronic Engine Comminication :
Enhanced instrumentation and engine ECU diagnostics via
electronic engine interface.
Ersin ERDALI 8
User Configurable Outputs and Inputs :
4 Outputs
8 Inputs
Ersin ERDALI 9
Analogue Inputs :
Flexible Sensor
Oil pressure
Coolant temperature
Fuel level
Ersin ERDALI 10
Control Logic :
* DSE 7320 control module has got 3 user defined control logic features. It can
be configured by selecting “User Defined Control” from external relay output
(3A @ 35V).
* For version 3.0 and higher (Upgrade version can be done in 7xxx modules).
Ersin ERDALI 11
PC Configuration Software :
Easier to use
Available file system
Useful menus and toolbar
Ersin ERDALI 12
INSTRUMENTS :
Mains Instruments
Generator Instruments
Volts
Volts
Frequency
Hz
Amps (optional)
Amps
kW
kVA
kVAR Engine Instruments
Pf RPM
kWh Oil Pressure
kVAh Coolant Temperature
KVARh Hours Run
Charging Voltage
Battery Volts
Ersin ERDALI 13
Warning Alarms :
Warnings are non-critical alarm conditions and do not affect the
operation of the generator system, they serve to draw the operators
attention to an undesirable condition.
Charge failure
Battery under voltage
Battery over voltage
Fail to stop
Auxiliary inputs
Low fuel level
Can ecu error
Earth fault (DSE7300 series v2.0.0 or above only)
Negative phase sequence (DSE7000 series v2.0.0 or above only)
(out of balance current loading of the generator)
Ersin ERDALI 14
Shutdown Alarms :
Shutdowns are latching alarms and stop the Generator. Clear the alarm and
remove the fault then press Stop/Reset to reset the module.
Fail to start
Emergency stop
Low oil pressure
Phase rotation (DSE7000 series v2.0.0 or above only)
Overspeed
Underspeed
Generator over frequency
Generator under frequency
Generator over voltage
Generator under voltage
Oil pressure sensor open circuit
High current
Loss of speed signal
ECU data fail
ECU shutdown
kW overload
Ersin ERDALI 15
Recommended Wiring Diagram - 1 :
Ersin ERDALI 16
Recommended Wiring Diagram - 2 :
Ersin ERDALI 17
Front Panel Functions :
Ersin ERDALI 18
Mimic Diagram Leds :
Ersin ERDALI 19
User Configurable Indicators :
These LEDs can be configured by the user to indicate any one of
different functions (warnings, shutdowns, status indications)
Ersin ERDALI 20
Mode Of Operation :
Ersin ERDALI 21
Front Panel Programming :
Manual programming buttons TFT LCD screen
Ersin ERDALI 22
Front Panel Configuration (Manual Programming) :
Ersin ERDALI 23
Accessing The Main Front Panel Configuration Editor :
Ensure the engine is at rest and the module is in STOP mode by pressing the
Stop/Reset button
If the PIN has been successfully entered (or the module PIN has not been
enabled), the editor is displayed :
Ersin ERDALI 24
Editing A Parameter :
Enter the editor as described above.
Press the (left) or (right) buttons to cycle to the section you wish to
view/change.
Press the (up) or (down) buttons to select the parameter you wish to
view/change within the currently selected section.
To edit the parameter, press to enter edit mode. The parameter begins to flash
to indicate that you are editing the value.
Press to save the value. The parameter ceases flashing to indicate that it has
been saved.
To exit the editor at any time, press and hold the button.
Ersin ERDALI 25
SYMBOLS
Charge fail
Generator
Ground Battery
Ersin ERDALI 26
DSE 2130 Expansion Module :
Ersin ERDALI 27
DSE 2157 Expansion Module :
Ersin ERDALI 28
DSE 2548 Expansion Module :
Ersin ERDALI 29
Remote Communications :
The 7300 series module includes RS232 and RS485 ports for communication
Internet
Modem
GSM
modem
Ersin ERDALI 30
RS485 Local Communication
Ersin ERDALI 31
QUESTIONS
ANSWERS
Ersin ERDALI 32