Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Rautkorpi
Rev. Date/Author Date/Checked Date/Approved Date/Issued Notes
SECN-L0018
Pöyry Finland Oy
IBG Pulp & Paper
P.O.Box 4 (Jaakonkatu 3)
FI-01621 Vantaa
Finland
Domicile Vantaa, Finland
Business ID. FI06259056
Tel. +358 10 3311
www.poyry.com
Date November 14, 2014
Page 2 (259)
Contact Jarmo Lindroos
Direct dial +358 10 33 22964
Direct fax +358 10 33 21818
Project Standard E-mail jarmo.lindroos@poyry.com
PIPING STANDARD
Contents 1 General
2 Austenitic Stainless Steel Piping
3 Carbon Steel Piping
4 Non-ferro-alloy Piping
5 Plastic Piping
6 Steam Traps, Seal Water and Service Piping Arrangements
7 Primary Support Standards for Piping
PIPING STANDARD 9HX191450-L0008
3(259)
1 GENERAL
PIPING STANDARD 9HX191450-L0008
5(259)
CONTENT 1(1)
Related documents:
General standards:
Pöyry Finland Oy
IBG Pulp & Paper
P.O.Box 4 (Jaakonkatu 3)
FI-01621 Vantaa
Finland
Domicile Vantaa, Finland
Business ID. FI06259056
Tel. +358 10 3311
www.poyry.com
Ref. No 9HX191450-L0005
Page 1 (14)
Project Standard Contact Jarmo Lindroos
Direct dial +358 10 33 22964
E-mail jarmo.lindroos@poyry.com
Contents
1 General
2 Nominal Dimensions
3. Nominal Pressure Classes for Piping, Flanges and Valves
4 Materials, Dimensions and Certificates
5 Selection of Piping Materials and Valves
7 Erection
8 Marking of Pipelines
9 Documents
10 Inspections and Testing
11 Guarantees
12 Painting
PIPING STANDARDS
9HX191450-L0008
GENERAL 7(259)
Pöyry Finland Oy
IBG Pulp & Paper
P.O.Box 4 (Jaakonkatu 3)
FI-01621 Vantaa
Finland
Domicile Vantaa, Finland
Business ID. FI06259056
Tel. +358 10 3311
www.poyry.com
Page 1 (5)
Project Standard Contact Jarmo Lindroos
Direct dial +358 10 33 22964
Direct fax +358 10 33 21818
E-mail jarmo.lindroos@poyry.com
Contents
1 General
2 Flow Substance Codes
3 Piping Material Abbreviations
4 Valve Material Abbreviations
5 Flange Gaskets
6 Valve Selection
D Do h\s 1.6 1.8 2.0 2.3 2.6 2.9 3.2 3.6 4.0 4.5 5.0 5.6
N
DN Do h\ s 1.6 1.8 2.0 2.3 2.6 2.9 3.2 3.6 4.0 4.5 5.0 5.6
50 7,90 8,18 8,46 8,88 9,29 9,70 10,10 10,64 11,16 11,80 12,43
50 60.3 80 11,81 12,09 12,38 12,79 13,20 13,61 14,02 14,55 15,07 15,71 16,34
100 14,92 15,21 15,49 15,90 16,32 16,72 17,13 17,66 18,18 18,82 19,45
60 10,48 10,84 11,20 11,74 12,27 12,79 13,31 14,00 14,68 15,52 16,35
65 76.1 90 14,93 15,29 15,65 16,19 16,72 17,24 17,77 18,45 19,13 19,97 20,80
120 20,29 20,65 21,01 21,54 22,08 22,60 23,12 23,81 24,49 25,33 26,16
60 12,45 13,08 13,70 14,32 14,94 15,75 16,56 17,56 18,54 19,71
80 88.9 90 17,09 17,72 18,35 18,97 19,58 20,40 21,21 22,20 23,19 24,35
120 22,64 23,27 23,90 24,52 25,13 25,95 26,76 27,75 28,74 29,90
60 14,91 15,73 16,55 17,36 18,16 19,23 20,29 21,60 22,90 24,45
100 114.3 100 21,82 22,64 23,45 24,26 25,07 26,14 27,19 28,51 29,81 31,35
140 30,33 31,15 31,97 32,78 33,58 34,65 35,71 37,02 38,32 39,87
60 17,38 18,39 19,39 20,39 21,39 22,71 24,02 25,65 27,26 29,18
125 139.7 100 24,80 25,81 26,81 27,81 28,80 30,12 31,43 33,06 34,68 36,60
140 33,82 34,83 35,83 36,83 37,83 39,15 40,46 42,09 43,70 45,62
60 20,16 21,38 22,60 23,81 25,02 26,62 28,22 30,20 32,17 34,52
150 168.3 100 28,15 29,37 30,59 31,80 33,01 34,61 36,21 38,19 40,16 42,51
180 48,96 50,18 51,40 52,61 53,82 55,42 57,01 59,00 60,97 63,32
70 30,39 31,98 33,57 35,68 37,78 40,39 42,99 46,10
200 219.1 120 42,41 44,00 45,59 47,70 49,80 52,41 55,01 58,12
200 66,87 68,46 70,05 72,15 74,25 76,87 79,47 82,57
70 36,70 38,70 40,68 43,33 45,96 49,24 52,51 56,42
250 273.0 120 50,08 52,07 54,06 56,70 59,33 62,62 65,89 69,79
200 76,70 78,70 80,68 83,33 85,96 89,24 92,51 96,42
80 45,39 47,76 50,13 53,28 56,42 60,33 64,23 68,90
300 323.9 120 57,32 59,69 62,05 65,20 68,34 72,26 76,16 80,82
220 94,16 96,53 98,90 102,05 105,19 109,10 113,00 117,67
PIPING STANDARDS 9HX191450-L0008
GENERAL 13(259)
50
50 60.3 80
100
60
65 76.1 90
120
60 19,71
80
88.9 90 24,35
120 29,90
60 24,45 26,23 28,23
100 114.3 100 31,35 33,13 35,13
140 39,87 41,64 43,65
60 29,18 31,40 33,91
125
139.7 100 36,60 38,82 41,33
140 45,62 47,84 50,35
60 34,52 37,24 40,31 43,73
168.3
150 100 42,51 45,23 48,30 51,72
180 63,32 66,03 69,11 72,53
70 46,10 47,64 49,70 53,78 58,34 62,35 68,32 73,24 80,52
200 219.1 120 58,12 59,66 61,71 65,80 70,36 74,37 80,34 85,25 92,54
200 82,57 84,12 86,17 90,26 94,81 98,83 104,80 109,71 116,99
70 56,42 60,96 66,11 71,87 76,96 84,53 90,78 100,07
250 273.0 120 69,79 74,33 79,48 85,25 90,33 97,90 104,16 113,45
200 96,42 100,96 106,11 111,87 116,96 124,53 130,78 140,07
80 68,90 74,32 80,48 87,38 93,48 102,57 110,08 121,27
300 323.9 120 80,82 86,24 92,41 99,31 105,40 114,49 122,01 133,19
220 117,67 123,09 129,25 136,15 142,25 151,34 158,85 170,04
PIPING STANDARDS 9HX191450-L0008
GENERAL 14(259)
220
100
220
100
220
PIPING STANDARDS 9HX191450-L0008
GENERAL 15(259)
DN Do 1.6 1.8 2.0 2.3 2.6 2.9 3.2 3.6 4.0 4.5 5.0 5.6
6 10.2 0,38 0,41 0,44 0,48 0,51 0,54 0,57 0,60 0,62 0,64 0,65 0,64
10 17.2 0,77 0,83 0,89 0,98 1,06 1,13 1,20 1,29 1,38 1,47 1,55 1,64
15 21.3 1,04 1,12 1,19 1,30 1,41 1,51 1,61 1,74 1,86 2,00 2,12 2,26
20 26.9 1,45 1,55 1,65 1,79 1,94 2,08 2,21 2,39 2,55 2,75 2,94 3,15
25 33.7 2,01 2,14 2,27 2,46 2,64 2,83 3,01 3,24 3,47 3,74 4,00 4,30
32 42.4 2,83 3,00 3,16 3,41 3,66 3,90 4,13 4,44 4,74 5,11 5,47 5,88
40 48.3 3,45 3,65 3,84 4,13 4,41 4,69 4,96 5,32 5,67 6,10 6,53 7,02
50 60.3 4,89 5,14 5,38 5,75 6,11 6,46 6,82 7,28 7,74 8,30 8,85 9,50
65 76.1 7,13 7,45 7,76 8,23 8,69 9,15 9,61 10,21 10,80 11,53 12,25 13,11
80 88.9 9,97 10,52 11,07 11,61 12,15 12,86 13,57 14,44 15,30 16,32
100 114.3 15,13 15,84 16,56 17,26 17,97 18,90 19,82 20,97 22,11 23,46
125 139.7 21,30 22,18 23,05 23,93 24,80 25,95 27,09 28,52 29,93 31,61
150 168.3 29,46 30,52 31,59 32,64 33,70 35,10 36,49 38,22 39,95 42,00
200 219.1 48,51 49,90 51,29 52,68 54,52 56,35 58,64 60,91 63,62
250 273.0 72,03 73,77 75,51 77,25 79,56 81,86 84,73 87,58 90,99
300 323.9 98,43 100,51 102,58 104,64 107,39 110,13 113,55 116,96 121,04
350 355.6 116,93 119,21 121,49 123,76 126,78 129,80 133,56 137,31 141,80
400 406.4 155,08 157,69 161,15 164,61 168,92 173,22 178,37
450 457 192,58 195,51 199,41 203,31 208,17 213,02 218,83
500 508 234,44 237,70 242,04 246,38 251,80 257,20 263,67
600 610 339,57 344,79 351,31 357,82 365,62
700 711 452,24 458,34 465,95 473,55 482,66
800 813 597,99 606,70 617,13
900 914 744,84 754,64 766,39
100 1016
0 909,40 920,31 933,38
110 1118
0 1090,3 1102,3 1116,7
120 1220
0 1287,6 1300,7 1316,4
PIPING STANDARDS 9HX191450-L0008
GENERAL 17(259)
DN Do 6.3 7.1 8.0 10.0 11.0 12.5 14.2 16.0 17.5 20.0 22.2 25.0
6 10.2
10 17.2
15 21.3
20 26.9
25 33.7
32 42.4
40 48.3
50 60.3
65 76.1
80 88.9
Note: For other densities (pipe and flow media) the weight shall be calculated case by case.
DN Do h\s 2.0 2.3 2.6 2.9 3.2 3.6 4.0 4.5 5.0
110 1118 80
0
100
70
120 1220 80
0
100
PIPING STANDARDS 9HX191450-L0008
GENERAL 23(259)
Table 1 gives support distances for freely supported pipe. These values
can be multiplied by x = 1.5 for gas and x = 1.3 for water pipes on
straight parts of the pipelines shown in Figure 2.
Heavy valves and other piping equipment shall be placed near the
support. Also elbows should have a support near them to prevent
sagging of the pipeline.
PIPING STANDARDS 9HX191450-L0008
GENERAL 26(259)
2 CALCULATION BASIS
Support distances in Table 1 have been calculated for freely supported
pipe (Figure 1) by formula:
384 E I f
I = 4
5q
where:
T [ °C ] E [ N/mm2 ]
50 198 000
120 193 000
180 187 000
3 BENDING STRESS
Bending stress for freely supported pipe have been checked applying
formula:
q 12 D 1
< x 0.2 v
16I 2 n
where:
PIPING STANDARDS 9HX191450-L0008
GENERAL 27(259)
4
Support distance L has been calculated as freely supported pipe (Figure 1)
by formula:
Figure
Fig. 1 1
384 E I f
l = 4
5q
where:
5
The support distance L can be multiplied by 1.5 if the pipe continues
symmetrically at the both pipe ends or if the pipe is fixed in one end and
continues symmetrically at the other end (See Figure 2).
PIPING STANDARDS 9HX191450-L0008
GENERAL 30(259)
Figure 2
6
Axial stresses caused gravity load calculated with the support distances
in the table from 10 N/mm2 to 50 N/mm2.
1 GENERAL
Following table 1 gives support distances for water pipes with different design
pressures (PN) and temperatures 60 C.
For gas pipes support distances in the table can be doubled but should not exceed 6 m.
2 REQUIREMENTS
Pipes shall be according to standards 340-001.
3 CALCULATION BASIS
In calculation pipe is freely supported.
f max< L / 700,
Table1
Maximum
pressure 0 MPa 0,1 MPa 0,25 MPa 0,4 MPa 0,6 MPa 1 MPa 1,6 MPa
Nominal
pressure/ PN1 PN2.5 PN4 PN6 PN10 PN16 PN25
DN
15 1.0 1.0 1.0 1.0 1.0 1.0 1.0
20 1.5 1.5 1.5 1.5 1.5 1.5 1.5
25 1.5 1.5 1.5 1.5 1.5 1.5 1.5
32 1.5 1.5 1.5 1.5 1.5 1.5 1.5
40 1.5 2.0 2.0 2.0 2.0 2.0 2.0
50 2.0 2.0 2.0 2.0 2.0 2.0 2.0
65 2.0 2.0 2.0 2.0 2.0 2.0 2.0
80 2.0 2.5 2.5 2.5 2.5 2.5 2.5
100 2.5 2.5 3.0 2.5 2.5 2.5 3.0
125 2.5 3.0 3.0 2.5 3.0 3.0 3.5
150 3.0 3.0 3.0 3.0 3.0 3.5 3.5
200 3.0 3.5 3.0 3.0 3.5 4.0 4.5
250 3.5 3.5 3.0 3.0 4.0 4.5 5.0
300 3.5 4.0 3.0 3.5 4.5 5.0 5.5
350 4.0 4.0 3.5 3.5 4.5 5.0 6.0
400 4.0 4.0 3.5 4.0 5.0 5.5 6.0
500 4.5 4.5 4.0 4.0 5.0 6.0 6.0
600 5.0 4.5 4.0 4.5 5.5 6.0 6.0
700 5.0 4.5 4.0 4.5 6.0 6.0
800 5.0 5.0 4.5 4.5 6.0 6.0
900 5.5 5.0 4.5 5.0 6.0 6.0
1000 6.0 5.5 4.5 5.0 6.0 6.0
1100 6.0 5.5 5.0 5.5 6.0 6.0
1200 6.0 5.5 5.5 5.5 6.0 6.0
1 DIMENSIONS
The distances on side and above the pipe are presented in Table 2. The
distances of PN16 flanges can be used also for lower pressure classes.
2 NOTE
The space requirement of equipment (handwheels of valves, etc.) and
pipe elongations shall be checked case by case.
PIPING STANDARDS 9HX191450-L0008
GENERAL 34(259)
DN 1200 1000 900 800 700 600 500 450 400 350 300 250 200
10 810 745 675 625 565 505 450 425 395 360 325 295 260
15 815 745 680 630 565 510 450 430 395 360 330 300 265
20 815 750 680 630 570 510 450 430 400 365 330 300 270
25 820 750 685 635 570 515 455 435 400 370 335 305 270
32 825 755 690 640 575 520 460 440 405 375 340 310 275
40 830 760 690 640 580 520 465 440 410 375 340 310 290
50 835 765 700 650 585 530 470 450 415 380 350 320 285
65 840 775 705 655 595 535 480 455 425 390 355 325 295
80 850 780 710 660 600 540 485 460 430 400 360 330 300
100 860 790 725 675 610 555 500 475 440 410 375 350 320
125 875 805 740 690 625 570 510 490 455 420 390 360 330
150 890 820 750 700 640 580 525 500 470 435 400 375 340
200 915 845 780 730 665 610 550 530 495 460 430 400 365
250 940 870 805 755 695 635 575 555 520 490 455 430
300 965 900 830 780 720 660 600 580 550 515 480
350 980 910 845 795 730 675 620 595 560 530
400 1010 940 870 820 760 700 645 620 590
450 1030 965 895 840 785 725 670 645
PIPING STANDARDS 9HX191450-L0008
GENERAL 35(259)
500 1060 990 920 870 810 750 695
600 1110 1040 970 920 860 800
700 1160 1090 1025 975 910
800 1210 1140 1075 1025
900 1260 1190 1125
1000 1310 1245
1200 1415
PIPING STANDARDS 9HX191450-L0008
GENERAL 36(259)
DN B C
PN 16 PN 25 PN 40 PN 63
10 65 65 65 70 235
15 70 70 70 75 243
20 75 75 75 - 258
25 80 80 80 90 273
32 90 90 90 - 310
40 95 95 95 105 325
1 GENERAL
Branch connection, reinforced-branch connection and factory-made tees are the main
types of tee connections. The selection between these types is mainly based on the
pressure strength, the DN1:DN2 ratio, the price and the space.
A factory-made tee is designed for the nominal pressure of the pipe class (see standard
313-011).
The dimensions of reinforcement plates are presented in Standard 313-014. The wall
thickness of the reinforcement plate must not exceed s in the calculations.
The maximum design pressure at the pressure side of the pump can be defined by
adding the head of the pump to the hydrostatic head.
The maximum design pressure of the tee connection at the suction side of a pump is
maximum hydrostatic head.
A reinforced branch with thick wall pipe or plate reinforcement shall be used if
pressure strength can be achieved with reinforcement, otherwise a factory-made tee
shall be selected.
External loads such as vibrations and big bending moments shall be considered when
necessary.
For high pressure piping tee-piece shall be selected. Tee pieces with DN2/ DN1 > 0.8
are not permissible for a design within the creep range of the material.
4 GRP PIPES
Tee-piece shall be specified for tee connections where the size of the branch pipe is
equal or up to two DN sizes smaller than the main pipe. Otherwise reinforced
branches shall be used.
PIPING STANDARDS 9HX191450-L0008
40(259)
1 GENERAL
This standard presents dimension standards and material specifications for piping
components of normal austenitic stainless steel pipe classes.
2 PIPE CLASSES
1) Design pressure is internal overpressure (pe), except for pipe classes 0H where
design pressure 0 refers to absolute pressure = 0.1 MPa external pressure (full
vacuum).
Hex head bolt 4) ISO 4014 Strength class 8.8 2.2 Hot dip
galvanized
Hex head bolt 4) ISO 4014 Strength class 2.2 Hot dip galvanized
8.8
(AVESTA 254SMO)
Blank and open spade 317-010 P265GH/ EN 10028-2/ 3.1
1.4547 lining, 2 mm EN 10028-7
(AVESTA 254SMO)
Plate valve 317-012 1.4547 EN 10217-7 3.1
(AVESTA 254SMO)
Cap EN 10253-4, 1.4547 EN 10253-4 3.1
Wallthickness same (AVESTA 254SMO)
as pipe wallthickness
Hex head bolt ISO 4014 Strength class 2.2 Hot dip galvanized
8.8
Nut ISO 4032 Strength class 8 2.2 Hot dip galvanized
Washer ISO 7089 Gr. A S 235JR EN 10025-2 Hot dip galvanized
Gasket EN 1514-1 Type IBC 2)
PN10-16 1) 3)
Threaded fittings EN 10241 1.4547 or equal EN 10272 Thread according
to ISO 7-1
Not for 40H1 and
63H1
1 GENERAL
This standard gives the coefficient k for defining the allowable pressures at elevated
temperatures generally for pipe classes and in detail for branch connections presented
in standards 313-012.
2 LIMITATIONS
The allowable pressure shall not exceed the nominal pressure of pipe classes
6H...63H.
3 COEFFICIENT k
4 EXAMPLES
Example 1:
Example 2:
Reinforced branch connection with plate reinforcement of Pipe class 16H2A, DN 800/
DN 500
Temperature = 150 C
Coefficient k = 0,80
Allowable pressure from standard 313-012 is 1,75 MPa
The allowable pressure = 0.8 x 1,75 MPa = 1,40 MPa, which means that the
reinforced branch connection stands the pressure 1,40 MPa.
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 49(259)
PIPES FOR PIPE CLASSES 6H...63H No: 310-010
1(1)
14.11.2014
1 DIMENSIONS
DN Do x s
1), 10H 16H 25H 40H 63H
0H
6H
6 10.2 x 1.6
10 17.2 x 1.6 According to
15 21.3 x 1.6 6H
20 26.9 x 1.6 According to
25 33.7 x 1.6 6H
(32) 42.4 x 1.6 According to
40 48.3 x 1.6 According 6H
50 60.3 x 1.6 to 60.3 x 2.0
(65) 76.1 x 1.6 6H 76.1 x 2.6
80 88.9 x 2.0 According to 88.9 x 3.2
100 114.3 x 2.0 6H 114.3 x 2.6 114.3 x 4.0
(125) 139.7 x 2.0 139.7 x 3.2 139.7 x 5.0
150 168.3 x 2.0 168.3 x 2.6 168.3 x 4.0 168.3 x 6.3
200 219.1 x 2.0 219.1 x 3.2 219,1 x 5.0
250 273 x 2.0 273 x 2.6 273 x 4.0 273 x 6.3
300 323.9 x 2.6 323.9 x 3.2 323.9 x 5.0
350 355.6 x 2.6 355.6 x 3.2 355.6 x 5.0
400 406.4 x 3.2 406.4 x 4.0 406.4 x 6.3
(450) 457 x 3.2 457 x 5.0 457 x 8.0
500 508 x 4.0 508 x 6.3 508 x 10
600 610 x 4.0 610 x 5.0 610 x 8.0 610 x 12.5
700 711 x 4.0 711 x 5.0 711 x 8.0 711 x 12.5
800 813 x 4.0 813 x 6.3 813 x 10 813 x 12.5
900 914 x 4.0 914 x 8.0 914 x 10
1000 1016 x 5.0 1016 x 8.0 1016 x 12,5
1200 1220 x 6.3 1220 x 10
2 DESIGNATION
Name, Do x s, material, standard No.
Example: Pipe, 114.3 x 2, 1.4404, EN 10217-7
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 50(259)
1 DIMENSIONS
DN Do s Lmax bxh
Notes: The effective throat thickness of fillet weld for the reinforcement ring is 0.7 x s,
were s is the wall thickness of the pipe.
Length of the welds on both sides of the ring must be at least 0.5 x circumference of
the pipe.
When using intermittent weld, the distance between welds must not exceed 8 x wall
thickness of the pipe.
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 51(259)
Extra reinforcement rings must be welded on to the pipe at both ends near bends.
2 DESIGNATION
1 DIMENSIONS
Do x s
DN R Type
40H 63H
According to
10 17.2 x 1.6
2 DESIGNATION
Name, Do x s, R, material, standard No.
Example: Elbow, 219.1 x 2.0, 305, 1.4404, EN 10253-4
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 54(259)
1 DIMENSIONS
See the following table for dimensions.
2 SUDDEN REDUCER
Sudden reducer, type S, to be used for pulp on suction side of a pump when
consistency C is 4 %.
Design of sudden reducer shall be verified with strength calculations by the Supplier.
Type S
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 56(259)
Wall thickness s
DN1 DN2 Do1 Do2 L
0H 10H 16H 25H 40H 63H
6H
Wall thickness s
DN1 DN2 Do1 Do2 L
0H 10H 16H 25H 40H 63H
6H
Note: The wall thickness of reducer is at least the same as the wall thicknesses of the
pipe at the bigger end of the reducer, however at least 2 mm.
4 DESIGNATION
Name, type, DN1/ DN2 x s, material, standard No.
Example 1: Reducer, C, 500/ 350 x 4.0, 1.4404, EN 10253-4
Example 2: Reducer, S, 500/ 350 x 4.0, 1.4404, 312-010
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 60(259)
1 DIMENSIONS
Table 1
DN1 DN2 Do1 Do2 L 0H 10H 16H 25H 40H 63H
6H
s1 / s2 s1 / s2 s1 / s2 s1 / s2 s1 / s2 s1 / s2
(32) 32 42.4 42.4 48 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6
(32) 25 42.4 33.7 48 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0
40 40 48.3 48.3 57 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 3.2 3.2
40 32 48.3 42.4 57 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 3.2 2.0
50 50 60.3 60.3 125 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6 4.0 4.0
50 40 60.3 48.3 125 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0 4.0 2.0
(65) 65 76.1 76.1 140 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6 3.2 3.2 5.0 5.0
(65) 50 76.1 60.3 140 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0 3.2 2.6 5.0 2.6
80 80 88.9 88.9 150 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6 4.0 4.0 5.0 5.0
80 (65) 88.9 76.1 150 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0 4.0 2.6 5.0 4.0
100 100 114.3 114.3 160 2.0 2.0 2.0 2.0 2.6 2.6 3.2 3.2 5.0 5.0 6.3 6.3
100 80 114.3 88.9 160 2.0 2.0 2.0 2.0 2.6 2.0 3.2 2.6 5.0 3.2 6.3 5.0
(125) 125 139.7 139.7 180 2.0 2.0 2.0 2.0 3.2 3.2 4.0 4.0 6.3 6.3 8.0 8.0
(125) 100 139.7 114.3 180 2.0 2.0 2.0 2.0 3.2 2.0 4.0 3.2 6.3 4.0 8.0 6.3
150 150 168.3 168.3 200 2.0 2.0 2.6 2.6 4.0 4.0 5.0 5.0 8.0 8.0 10.0 10.0
150 (125) 168.3 139.7 200 2.0 2.0 2.6 2.0 4.0 2.0 5.0 4.0 8.0 4.0 10.0 8.0
200 200 219.1 219.1 250 2.6 2.6 3.2 3.2 5.0 5.0 6.3 6.3 10.0 10.0
200 150 219.1 168.3 250 2.6 2.0 3.2 2.6 5.0 2.6 6.3 5.0 10.0 5.0
250 250 273.0 273.0 300 2.6 2.6 4.0 4.0 6.3 6.3 8.0 8.0 12.5 12.5
250 200 273.0 219.1 300 2.6 2.6 4.0 3.2 6.3 3.2 8.0 6.3 12.5 8.0
300 300 323.9 323.9 330 3.2 3.2 5.0 5.0 6.3 6.3 10.0 10.0
300 250 323.9 273.0 330 3.2 2.6 5.0 4.0 6.3 5.0 10.0 6.3
350 350 355.6 355.6 360 4.0 4.0 5.0 5.0 8.0 8.0 10.0 10.0
350 300 355.6 323.9 360 4.0 3.2 5.0 5.0 8.0 6.3 10.0 10.0
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 62(259)
Table 1 (continues)
6H
s1 / s2 s1 / s2 s1 / s2 s1 / s2
400 400 406.4 406.4 400 4.0 4.0 6.3 6.3 8.0 8.0 12.5 12.5
400 350 406.4 355.6 400 4.0 4.0 6.3 5.0 8.0 8.0 12.5 10.0
(450) 450 457.0 457.0 450 5.0 5.0 6.3 6.3 10.0 10.0 12.5 12.5
(450) 400 457.0 406.4 450 5.0 4.0 6.3 6.3 10.0 8.0 12.5 12.5
500 500 508.0 508.0 500 5.0 5.0 8.0 8.0 10.0 10.0 14.2 14.2
500 (450) 508.0 457.0 500 5.0 5.0 8.0 6.3 10.0 10.0 14.2 12.5
600 600 610.0 610.0 600 6.3 6.3 10.0 10.0 12.5 12.5 17.5 17.5
600 500 610.0 508.0 600 6.3 5.0 10.0 6.3 12.5 10.0 17.5 14.2
700 700 711.0 711.0 700 8.0 8.0 10.0 10.0 14.2 14.2 20.0 20.0
700 600 711.0 610.0 700 8.0 5.0 10.0 10.0 14.2 12.5 20.0 16.0
800 800 813.0 813.0 800 8.0 8.0 12.5 12.5 16.0 16.0 20.0 20.0
800 700 813.0 711.0 800 8.0 8.0 12.5 10.0 16.0 14.2 20.0 20.0
900 900 914.0 914.0 900 10.0 10.0 12.5 12.5 16.0 16.0
900 800 914.0 813.0 900 10.0 8.0 12.5 12.5 16.0 16.0
1000 1000 1016.0 1016.0 1000 10.0 10.0 14.2 14.2 20.0 20.0
1000 900 1016.0 914.0 1000 10.0 10.0 14.2 12.5 20.0 16.0
2 DESIGNATION
Name, DN1/ DN2, s1/s2, material, standard No.
Example: Tee piece, 200/ 200, 3.2/ 3.2, 1.4404, EN 10253-4
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 64(259)
1 GENERAL
The allowed pressures for the normal wall thicknesses for each pipe class have been
calculated according to EN 13480-3. The pipes are with wall thicknesses according to
different pipe classes. The branches are reinforced with plate. See standard 313-014.
2 CALCULATION BASIS
Material 1.4404
Temperature t = 20 C
Corrosion allowance c o = 0 mm
Tolerance allowance c = 10 % however at least ± 0.2 mm for diameters
21...1220 mm
3 TABLES
Allowable pressure tables for normal walls of pipe classes:
Table 1 4H and 6H reinforced-branch connection
Table 2 10H reinforced-branch connection
Table 3 16H reinforced-branch connection
Table 4 25H reinforced-branch connection
Table 5 40H reinforced-branch connection
Table 6 63H reinforced-branch connection
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 65(259)
REINFORCED-BRANCH CONNECTIONS- No: 313-012
ALLOWABLE PRESSURES 2(7)
Table 1 Allowable pressure (MPa) for reinforced-branch connection 14.11.2014
See standard 301-090, item 2.2
Pipe class 4H and 6H
4 DESIGNATION
Name, Reinforced branch connection, Do1/ Do2, s1/ s2, material, standard No.
1 DIMENSIONS
DN1 lpl
40 15
50 15
(65) 15
80 15
100 15
(125) 16
150 17
200 20
250 22
300 27
350 29
400 31
(450) 36
500 43
600 47
700 50
800 54
900 57
1000 67
1200 83 mm
std
16/01/17
The wall thickness of the reinforcing plate must be minimum the wall thickness of the
main pipe (s).
2 DESIGNATION
Name DN 1/ DN 2, material, standard No.
PIPING STANDARDS
9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING
72(259)
Example: Reinforced - branch connection, 200/ 25, 1.4404, 313-014
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 73(259)
3 DIMENSIONS
According to standards of the table.
10
15
25 flange flange
40 standard standard
250
(450)
500
600
700
800
900
1000
1200
2 DESIGNATION
Name, standard No.
Example: Summary of collars, 314-010
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 74(259)
SUMMARY OF FLANGES
No: 315-010
1(1)
14.11.2014
1 DIMENSIONS
According to standards in the table.
Types and standards of flanges at temperature 20C
DN
0H 16H 25H 40H 63H
6H, 10H
15 Loose flange Loose flange Loose flange Welding neck Welding neck
40 PN 10 PN 16 PN 25 EN 1092-1 EN 1092-1
50 Type 11 Type 11
(65) PN 40 PN 63
80
150 hot dip hot dip hot dip pipe class pipe class
250
300
350
400
(450)
500
600
700
800
900
1000
1200
2 DESIGNATION
Name, standard No.
Example: Summary of flanges, 315-010
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 75(259)
BLANK FLANGE 0H...25H No: 316-010
1(1)
14.11.2014
1 DIMENSIONS
2 DESIGNATION
Name, DN, pressure class of pipe class, material of the flange, material of lining plate,
standard No.
Example: Blank flange, DN 250, PN 16, P265GH, 1.4404, 316-010
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 76(259)
1 GENERAL
Spade blank according to this standard shall be used between flanges instead of shut-
off valve.
When s1 > 8 mm, the material is P265GH, which has been lined with 1.4404.
PIPING STANDARDS
9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING
77(259)
SPADE BLANK No: 317-010
2(2)
14.11.2014
0.1 MPa 0.25 MPa 0.4 MPa 0.6 MPa 1.0 MPa
15 45 20
20 58
25 68 2
(32) 78 2 75
40 88 3
50 102 2 30
(65) 122 2 3 4
80 138 3 4 5
100 158 3 4 5 6
(125) 188 2
2 DESIGNATION
Name, DN, pressure difference, standard No.
Example: Spade blank, 150, 0.6, 317-010
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 78(259)
1 GENERAL
Open spade according to this standard shall be used between flanges when spade bank
according to standard 317-010 has been removed.
2 DIMENSIONS
Table 1
Plate thickness (mm) L B
s
Pressure difference, MPa
DN D1 D 0.1 MPa 0.25 MPa 0.4 MPa 0.6 MPa 1.0 MPa
15 21 45 20
20 27 58
25 34 68 2
(32) 42 78 2 75
40 48 88 3
50 60 102 2 30
(65) 76 122 2 3 4
80 89 138 3 4 5
3 MATERIAL
When s1 < 8 mm, material is 1.4404, and when s1 > 8 mm, material is P265GH, or
equal with 1.4404 lining.
2. Two holes in handle indicates open spade (one for spade blank)
4 DESIGNATION
Name, DN, pressure difference, standard No.
Example: Open spade, 250, 0.25, 317-011
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 80(259)
1 GENERAL
Plate valve shall be used between flanges instead of shut-off valve.
2 DIMENSIONS
DN 0H...10H
A B C D E R S MPa
1 MATERIAL
1.4404 according to EN 10028-7
2 DESIGNATION
Name, DN, standard No.
Example: Plate valve, DN 250, 317-012
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 81(259)
1 DIMENSIONS
Type A Type B
DN 50
DN 40
2 DESIGNATION
Name, DN, type, material, standard No.
Example: Drain connection, DN 50, A, 1.4404, 320-012
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 83(259)
1 DIMENSIONS
2 DESIGNATION
Name, DN, type, material, standard No.
Example: Vent connection, DN 25, A, 1.4404, 320-015
PIPING STANDARDS 9HX191450-L0008
AUSTENITIC STAINLESS STEEL PIPING 84(259)
1 DIMENSIONS
DN 40
2 DESIGNATION
Name, material, standard No.
Example: Sample taking connection, DN 40, 1.4404, 320-020
PIPING STANDARDS 9HX191450-L0008
85(259)
Pressure Temperature
MPa °C
1.0 20
0.7 200
Pipe
DN 10...300 EN 10216-2 P235GH EN 10216-2 3.1 Seamless
330-010
DN 350…DN 1200 EN 10217-2 +A1or P235GH EN 10217-2+A1 or 3.1 Welded
EN 10217-5+A1, EN 10217-5+A1 3.1 Welded
330-010
Elbow
DN 10...20 Bent pipe P235GH EN 10216-2 3.1 R = 3...5Do
DN 25..1200 EN 10253-2, 331-010 P235GH EN 10253-2 3.1 R = 1.5Do
Tee-piece
DN 20…1200 EN 10253-2, 333-010 P235GH EN 10253-2 3.1
Branch
connection
DN 10...300 EN 10216-2 P235GH EN 10216-2 3.1
DN 350...1200 EN 10217-2 +A1or P235GH EN 10217-2 or 3.1
EN 10217-5+A1 EN 10217-5 3.1
Reducer
DN 20...1200 EN 10253-2, 332-010 P235GH EN 10253-2 3.1
Cap
DN 20...1200 EN 10253-2 P235GH EN 10253-2 3.1
Blank flange
DN 10...1200 EN 1092-1 PN 10, P265GH EN 10028-2 3.1
Type 05
1) Gasket material depends on flow substance. See “9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selections”.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 89(259)
PIPE CLASSES, SUMMARY No: 330-001
PIPE CLASS 16C1C 3(16)
14.11.2014
Pressure Temperature
MPa °C
1.6 20
1.0 160
Pipe
DN 10...300 EN 10216-2 P235GH EN 10216-2 3.1 Seamless
330-010
DN 350…DN 700 EN 10217-2 +A1or P235GH EN 10217-2+A1 or 3.1 Welded
EN 10217-5+A1, EN 10217-5+A1 3.1 Welded
330-010
Elbow
DN 10...20 Bent pipe P235GH EN 10216-2 3.1 R = 3...5Do
DN 25..700 EN 10253-2, 331-010 P235GH EN 10253-2 3.1 R = 1.5Do
Tee-piece
DN 20…700 EN 10253-2, 333-010 P235GH EN 10253-2 3.1
Branch
connection
DN 10...300 EN 10216-2 P235GH EN 10216-2 3.1
DN 350...700 EN 10217-2 +A1or P235GH EN 10217-2+A1 or 3.1
EN 10217-5+A1 EN 10217-5+A1 3.1
Reducer
DN 20...700 EN 10253-2, 332-010 P235GH EN 10253-2 3.1
Cap
DN 20...700 EN 10253-2 P235GH EN 10253-2 3.1
Blank flange
DN 10...700 EN 1092-1 PN 16, P265GH EN 10028-2 3.1
Type 05
1) Gasket material depends on flow substance. See “9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selections”.
Pressure Temperature
MPa °C
2.5 20
1.6 220
Pipe
DN 10...700 EN 10216-2 P235GH EN 10216-2 3.1 Seamless
330-010
Elbow
DN 10...20 Bent pipe P235GH EN 10216-2 3.1 R = 3...5Do
DN 25...700 EN 10253-2, 331-010 P235GH EN 10253-2 3.1 R = 1.5Do
Tee-piece
DN 20…700 EN 10253-2, 333-010 P235GH EN 10253-2 3.1
Branch
connection
DN 10...700 EN 10216-2 P235GH EN 10216-2 3.1
Reducer
Cap
DN 20...700 EN 10253-2 P235GH EN 10253-2 3.1
1) Gasket material depends on flow substance. See “9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selection”.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 91(259)
PIPE CLASSES, SUMMARY No: 330-001
PIPE CLASS 40C1B 5(16)
14.11.2014
Pressure Temperature
MPa °C
4.0 20
1.6 300
Pipe
DN 10...600 EN 10216-2 P235GH EN 10216-2 3.1 Seamless
330-010
Elbow
DN 10...20 Bent pipe P235GH EN 10216-2 3.1 R = 3...5Do
DN 25...700 EN 10253-2, 331-010 P235GH EN 10253-2 3.1 R = 1.5Do
Tee-piece
DN 20…700 EN 10253-2, 333-010 P235GH EN 10253-2 3.1
Branch
connection
DN 10...700 EN 10216-2 P235GH EN 10216-2 3.1
Reducer
Cap
DN 20...700 EN 10253-2 P235GH EN 10253-2 3.1
1) Gasket material depends on flow substance. See “9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selection”.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 92(259)
PIPE CLASSES, SUMMARY No: 330-001
PIPE CLASS 63C2B 6(16)
14.11.2014
Pressure Temperature
MPa °C
6.3 20
6.0 160
4.0 250
Pipe
DN 10...300 EN 10216-2 16Mo3 EN 10216-2 3.1 Seamless
330-010
Elbow
DN 10...20 Bent pipe 16Mo3 EN 10216-2 3.1
Tee-piece
DN 20…300 EN 10253-2, 16Mo3 EN 10253-2 3.1
333-010
Branch
connection
DN 10...150 EN 10216-2 16Mo3 EN 10216-2 3.1
Reducer
DN 20...300 EN 10253-2, 16Mo3 EN 10253-2 3.1
332-010
Cap
DN 20...300 EN 10253-2, 16Mo3 EN 10253-2 3.1
1) Gasket material depends on flow substance. See 9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selection” .
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 93(259)
PIPE CLASSES, SUMMARY No: 330-001
PIPE CLASS 160C3B 7(16)
14.11.2014
Pressure Temperature
MPa °C
12,0 520
Pipe
DN 10…125 EN 10216-2 10CrMo9-10 EN 10216-2 3.1 Seamless
330-010
DN 150…700 EN 10216-2 X10CrMoVNb9-1 EN 10216-2 3.1 Seamless
330-010
Elbow
DN 10-125 EN 10216-2 10CrMo9-10 EN 10216-2 3.1 Main dimensions
Bent pipe, R = 5D according to
DN 150…700 EN 10216-2 X10CrMoVNb9-1 EN 10216-2 3.1 manufacturer’s
Bent pipe, R = 5D design.
Reducer
DN 10-125 Wall thickness same as 10CrMo9-10 EN 10253-2 3.1 Main dimensions
DN 150-700 that of bigger pipe X10CrMoVNb9-1 EN 10253-2 3.1 according to
manufacturer’s
design.
1) Gasket material depends on flow substance. See 9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selection
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 94(259)
PIPE CLASSES, SUMMARY No: 330-001
PIPE CLASS 160C4B 8(16)
14.11.2014
Pressure Temperature
MPa °C
14,5 340
Pipe
DN 10…400 EN 10216-2 10CrMo9-10 EN 10216-2 3.1 Seamless
330-010
Elbow
DN 10-400 EN 10216-2 10CrMo9-10 EN 10216-2 3.1 Main dimensions
Bent pipe, R = 5D according to
Wall thickness same as manufacturer’s
that of pipe design.
Cap
DN 10-400 EN 10253-2 10CrMo9-10 EN 10253-2 3.1 Main dimensions
R1=0,8D, r=0.15D according to
Wall thickness same as manufacturer’s
that of pipe design.
Tee-piece
DN 10… 400 Special T-piece, 10CrMo9-10 EN 10253-2 3.1 Main dimensions
according to
manufacturer’s
design.
Reducer
DN 10-400 Wall thickness same as 10CrMo9-10 EN 10253-2 3.1 Main dimensions
that of bigger pipe according to
manufacturer’s
design.
1) Gasket material depends on flow substance. See 9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selection
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 95(259)
PIPE CLASSES, SUMMARY No: 330-001
PIPE CLASS 250C2B 9(16)
14.11.2014
Pressure Temperature
MPa °C
20,0 160
Pipe
DN 10…300 EN 10216-2 16Mo3 EN 10216-2 3.1 Seamless
330-010
Elbow
DN 10-300 EN 10216-2 16Mo3 EN 10216-2 3.1 Main dimensions
Bent pipe, R = 5D according to
Wall thickness same as manufacturer’s
that of pipe design.
Cap
DN 10-300 EN 10253-2 16Mo3 EN 10253-2 3.1 Main dimensions
R1=0,8D, r=0.15D according to
Wall thickness same as manufacturer’s
that of pipe design.
Tee-piece
DN 10… 300 Special T-piece, 16Mo3 EN 10253-2 3.1 Main dimensions
according to
manufacturer’s
design.
Reducer
DN 10-300 Wall thickness same as 16Mo3 EN 10253-2 3.1 Main dimensions
that of bigger pipe according to
manufacturer’s
design.
1) Gasket material depends on flow substance. See 9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selection”
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 96(259)
PIPE CLASSES, SUMMARY No: 330-001
PIPE CLASS 150C5B 10(16)
14.11.2014
Pressure Temperature
MPa °C Corrosion allowance 1 mm Pi Di Material N
Manufacturing tolerance of pi m o
0.605 182 pipe -12.5% n en t
g si e
c on s
o s
m
p
o
n
e
nt
D S C
e t e
s a r
i n t
g d i
n a f
a r i
ti d c
o a
n t
e
Pi
p AS A A M S
e M 1 S a e
D E 0 T n a
N B3 6 M u m
1 6. G f l
5. 10 r. a e
A
.. M B c s
1
1 33 t s
0
2 4- u
6
0 01 r
M
0 0 e
r
’
s
M
a
t
e
r
i
a
l
T
e
s
t
R
e
p
o
r
t
El
b AS A A M 2
o M 1 S a )
w E 0 T n R
D B1 5 M u
N 6. A f
1 9 2 A a =
5. 3 1 c
.. 4 0 t 1
1 G 5 u .
2 r. M r 5
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 97(259)
Piping Dimensions Material Notes
component
Designation Standard Certificate
Tee-piece 2)
DN 20…1200 ASME B16.9 A105 ASTM A105M Manufacturer’s
A234 Gr. WPB ASTM A234M Material Test
Report
Branch
connection Manufacturer’s set on
DN 15...1200 ASME B36.10M A106 Gr. B ASTM A106M Material Test pad
weldolet
Report sockolet
Reducer Manufacturer’s 2)
DN 20…1200 ASME B16.9 A105 ASTM A105M Material Test
A234 Gr. WPB ASTM A234M Report
Cap 2)
DN 20…1200 ASME B16.9 A105 ASTM A105M Manufacturer’s
A234 Gr.WPB ASTM A234M Material Test
Report
Welding neck flange
DN 15...600 ASME B16.5, Class 150 A105 ASTM A105M Manufacturer’s
raised face Material Test
DN 700…DN 1200 ASME B16.47, series A, Report
Class 150 raised face
Blank flange
DN 15...600 ASME B16.5, Class 150 A515 Gr. 70 ASTM A515M Manufacturer’s
DN 700…DN 1200 ASME B16.47, series A, Material Test
Class 150 raised face Report
1) Gasket material depends on flow substance. See “9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selections”.
2) Fittings shall stand same pressure as pipe.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 98(259)
PIPE CLASSES, SUMMARY No: 330-001
PIPE CLASS 300C5B 11(16)
14.11.2014
Pressure Temperature
MPa °C Corrosion allowance 1 mm Pi Di Material N
Manufacturing tolerance of pi m o
1.485 222 pipe -12.5% n en t
g si e
c on s
o s
m
p
o
n
e
nt
D S C
e t e
s a r
i n t
g d i
n a f
a r i
ti d c
o a
n t
e
Pi
p AS A A M S
e M 1 S a e
D E 0 T n a
N B3 6 M u m
1 6. G f l
5. 10 r. A a e
.. M, B 1 c s
1 33 0 t s
0 4- 6 u
0 01 M r
0 0 e
r
’
s
M
a
t
e
r
i
a
l
T
e
s
t
R
e
p
o
r
t
El
b AS A A M 2
o M 1 S a )
w E 0 T n R
D B1 5 M u
N 6. A f
1 9 2 A a =
5. 3 1 c
.. 4 0 t 1
1 G 5 u .
0 r. M r 5
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 99(259)
Piping Dimensions Material Notes
component
Designation Standard Certificate
Tee-piece 2)
DN 20…800 ASME B16.9 A105 ASTM A105M Manufacturer’s
A234 Gr. WPB ASTM A234M Material Test
Report
Branch
connection Manufacturer’s set on
DN 15...1000 ASME B36.10M A106 Gr. B ASTM A106M Material Test pad
weldolet
Report sockolet
Reducer Manufacturer’s 2)
DN 20…800 ASME B16.9 A105 ASTM A105M Material Test
A234 Gr. WPB ASTM A234M Report
Cap 2)
DN 20…800 ASME B16.9 A105 ASTM A105M Manufacturer’s
A234 Gr. WPB ASTM A234M Material Test
Report
Welding neck flange
DN 15...600 ASME B16.5, A105 ASTM A105M Manufacturer’s
Class 300 Material Test
raised face Report
DN 700…1000 ASME B16.47, series A,
Class 300 raised face
Blank flange
DN 15...600 ASME B16.5, A515 Gr. 70 ASTM A515M Manufacturer’s
Class 300 Material Test
raised face Report
DN 700…1000 ASME B16.47, series A,
Class 300
raised face
1) Gasket material depends on flow substance. See “9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selections”.
2) Fittings shall stand same pressure as pipe.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 100(259)
PIPE CLASS 300C6B 12(16)
14.11.2014
Pressure Temperature
MPa °C Pi Di Material N
Corrosion allowance 1 mm pi m o
1.485 475 Manufacturing tolerance of n en t
0.8 490 pipe -12.5% g si e
c on s
o s
m
p
o
n
e
nt
D S C
e t e
s a r
i n t
g d i
n a f
a r i
ti d c
o a
n t
e
Pi
p AS A A M S
e M 3 S a e
D E 3 T n a
N B3 5 M u m
1 6. P f l
5. 10 1 A a e
.. M, 1 3 c s
9 33 3 t s
0 4- 5 u
0 01 M r
0 e
r
’
s
M
a
t
e
r
i
a
l
T
e
s
t
R
e
p
o
r
t
El
b AS A A M 2
o M 1 S a )
w E 8 T n R
D B1 2 M u
N 6. G f
1 9 r. A a =
5. F 1 c
.. 1 8 t 2
9 1 2 u .
0 M r 5
0 e
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 101(259)
Piping Dimensions Material Notes
component
Designation Standard Certificate
Tee-piece 2)
DN 20…900 ASME B16.9 A182 Gr. F11 ASTM A182M Manufacturer’s
Material Test
Report
Reducer Manufacturer’s 2)
DN 20…900 ASME B16.9 A182 Gr. F11 ASTM A182M Material Test
Report
Cap 2)
DN 20…900 ASME B16.9 A182 Gr. F11 ASTM A182M Manufacturer’s
Material Test
Report
Welding neck flange
DN 15...600 ASME B16.5, A182 Gr. F11 ASTM A182M Manufacturer’s
Class 300 Material Test
raised face Report
DN 700…900 ASME B16.47, series A,
Class 300 raised face
Blank flange
DN 15...600 ASME B16.5, A387 Gr. 11 Cl. 2 ASTM A387M Manufacturer’s
Class 300 Material Test
raised face Report
DN 700…900 ASME B16.47, series A,
Class 300
raised face
Bolt ANSI B18.2.1, stud bolt A193 Gr. B16 ASTM A193M Manufacturer’s Electro
Material Test galvanized
Nuts ANSI B18.2,2, heavy A194 Gr. 3 ASTM A194M Report Electro
hexagonal galvanized
1) Spiral wound gasket with inner and centering rings . Metal winding strips and inner ring of 316L. Filler material of purity graphite.
2) Fittings shall stand same pressure as pipe.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 102(259)
PIPE CLASS 400C5B 13(16)
14.11.2014
Pressure Temperature
MPa °C Corrosion allowance 1 mm Pi Di Material N
Manufacturing tolerance of pi m o
3.85 322 pipe -12.5% n en t
g si e
c on s
o s
m
p
o
n
e
nt
D S C
e t e
s a r
i n t
g d i
n a f
a r i
ti d c
o a
n t
e
Pi
p AS A A M S
e M 1 S a e
D E 0 T n a
N B3 6 M u m
1 6. G f l
5. 10 r. A a e
.. M, B 1 c s
9 33 0 t s
0 4- 6 u
0 01 M r
0 e
r
’
s
M
a
t
e
r
i
a
l
T
e
s
t
R
e
p
o
r
t
El
b AS A A M 2
o M 1 S a )
w E 0 T n R
D B1 5 M u
N 6. A f
1 9 2 A a =
5. 3 1 c
.. 4 0 t 1
9 G 5 u .
0 r. M r 5
0 W A e
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 103(259)
Piping Dimensions Material Notes
component
Designation Standard Certificate
Tee-piece 2)
DN 20…900 ASME B16.9 A105 ASTM A105M Manufacturer’s
A234 Gr. WPB ASTM A234M Material Test
Report
Reducer Manufacturer’s 2)
DN 20…900 ASME B16.9 A105 ASTM A105M Material Test
A234 Gr. WPB ASTM A234M Report
Cap 2)
DN 20…900 ASME B16.9 A105 ASTM A105M Manufacturer’s
A234 Gr. WPB ASTM A234M Material Test
Report
Welding neck flange
DN 15...600 ASME B16.5, A105 ASTM A105M Manufacturer’s
Class 400 Material Test
raised face Report
DN 700…900 ASME B16.47, series A,
Class 400 raised face
Blank flange
DN 15...600 ASME B16.5, A515 Gr. 70 ASTM A515M Manufacturer’s
Class 400 Material Test
raised face Report
DN 700…900 ASME B16.47, series A,
Class 400
raised face
Bolt ANSI B18.2.1, stud bolt A193 Gr. B7 ASTM A193M stamped Electro
galvanized
Nuts ANSI B18.2,2, heavy A194 Gr. 4 ASTM A194M Electro
hexagonal galvanized
1) Gasket material depends on flow substance. See “9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selections”.
2) Fittings shall stand same pressure as pipe.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 104(259)
PIPE CLASS 400C6B 14(16)
14.11.2014
Pressure Temperature
MPa °C Corrosion allowance 1 mm Pi Di Material N
Erosion allowance 2 mm pi m o
3.85 450 Manufacturing tolerance of n en t
pipe -12.5% g si e
c on s
o s
m
p
o
n
e
nt
D S C
e t e
s a r
i n t
g d i
n a f
a r i
ti d c
o a
n t
e
Pi
p AS A A M S
e M 3 S a e
D E 3 T n a
N B3 5 M u m
1 6. P f l
5. 10 1 A a e
.. M, 1 3 c s
9 33 3 t s
0 4- 5 u
0 01 M r
0 e
r
’
s
M
a
t
e
r
i
a
l
T
e
s
t
R
e
p
o
r
t
El
b AS A A M 2
o M 1 S a )
w E 8 T n R
D B1 2 M u
N 6. G f
1 9 r. A a =
5. F 1 c
.. 1 8 t 2
9 1 2 u .
0 M r 5
0 e
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 105(259)
Piping Dimensions Material Notes
component
Designation Standard Certificate
Tee-piece 2)
DN 20…900 ASME B16.9 A182 Gr. F11 ASTM A182M Manufacturer’s
Material Test
Report
Reducer Manufacturer’s 2)
DN 20…900 ASME B16.9 A182 Gr. F11 ASTM A182M Material Test
Report
Cap 2)
DN 20…900 ASME B16.9 A182 Gr. F11 ASTM A182M Manufacturer’s
Material Test
Report
Welding neck flange
DN 15...600 ASME B16.5, A182 Gr. F11 ASTM A182M Manufacturer’s
Class 400 Material Test
raised face Report
DN 700…900 ASME B16.47, series A,
Class 400 raised face
Blank flange
DN 15...600 ASME B16.5, A387 Gr. 11 Cl. 2 ASTM A387M Manufacturer’s
Class 400 Material Test
raised face Report
DN 700…900 ASME B16.47, series A,
Class 400
raised face
Bolt ANSI B18.2.1, stud bolt A193 Gr. B16 ASTM A193M Manufacturer’s Electro
Material Test galvanized
Nuts ANSI B18.2,2, heavy A194 Gr. 3 ASTM A194M Report Electro
hexagon galvanized
1) Spiral wound gasket with inner and centering rings . Metal winding strips and inner ring of 316L. Filler material of purity graphite.
2) Fittings shall stand same pressure as pipe.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 106(259)
PIPE CLASS 600C6B 15(16)
14.11.2014
Pressure Temperature
MPa °C Pi Di Material N
Corrosion allowance 1 mm pi m o
5.6 450 Manufacturing tolerance of n en t
pipe -12.5% g si e
c on s
o s
m
p
o
n
e
nt
D S C
e t e
s a r
i n t
g d i
n a f
a r i
ti d c
o a
n t
e
Pi
p AS A A M S
e M 3 S a e
D E 3 T n a
N B3 5 M u m
1 6. P f l
5. 10 1 A a e
.. M, 1 3 c s
9 33 3 t s
0 4- 5 u
0 01 M r
0 e
r
’
s
M
a
t
e
r
i
a
l
T
e
s
t
R
e
p
o
r
t
El
b AS A A M 2
o M 1 S a )
w E 8 T n R
D B1 2 M u
N 6. G f
1 9 r. A a =
5. F 1 c
.. 1 8 t 2
9 1 2 u .
0 M r 5
0 e
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 107(259)
Piping Dimensions Material Notes
component
Designation Standard Certificate
Tee-piece 2)
DN 20…900 ASME B16.9 A182 Gr. F11 ASTM A182M Manufacturer’s
Material Test
Report
Reducer Manufacturer’s 2)
DN 20…900 ASME B16.9 A182 Gr. F11 ASTM A182M Material Test
Report
Cap 2)
DN 20…900 ASME B16.9 A182 Gr. F11 ASTM A182M Manufacturer’s
Material Test
Report
Welding neck flange
DN 15...600 ASME B16.5, A182 Gr. F11 ASTM A182M Manufacturer’s
Class 600 Material Test
raised face Report
DN 700…900 ASME B16.47, series A,
Class 600 raised face
Blank flange
DN 15...600 ASME B16.5, A387 Gr. 11 Cl. 2 ASTM A387M Manufacturer’s
Class 600 Material Test
raised face Report
DN 700…900 ASME B16.47, series A,
Class 600
raised face
Bolt ANSI B18.2.1, stud bolt A193 Gr. B16 ASTM A193M Manufacturer’s Electro
Material Test galvanized
Nuts ANSI B18.2,2, heavy A194 Gr. 3 ASTM A194M Report Electro
hexagon galvanized
1) Spiral wound gasket with inner and centering rings . Metal winding strips and inner ring of 316L. Filler material of purity graphite.
2) Fittings shall stand same pressure as pipe.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 108(259)
PIPE CLASS 1500C8B 16(16)
14.11.2014
Pressure Temperature
MPa °C Pi Di Material N
Corrosion allowance 1 mm pi m o
12.1 530 Manufacturing tolerance of n en t
pipe -12.5% g si e
c on s
o s
m
p
o
n
e
nt
D S C
e t e
s a r
i n t
g d i
n a f
a r i
ti d c
o a
n t
e
Pi
p AS A A M S
e M 3 S a e
D E 3 T n a
N B3 5 M u m
1 6. P f l
5. 10 9 A a e
.. M, 1 3 c s
6 33 3 t s
0 4- 5 u
0 01 M r
D 0 e
N 71 r
7 1x ’
0 44 s
0 .4
… 5 M
9 81 a
0 3x t
0 49 e
.9 r
9 i
91 a
4x l
53 T
.9 e
8 s
t
R
e
p
o
r
t
El
b AS A A M 2
o M 1 S a )
w E 8 T n R
D B1 2 M u
N 6. G f
1 9 r. A a =
5. F 1 c
.. 9 8 t 2
9 1 2 u .
0 M r 5
0 e
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 109(259)
Piping Dimensions Material Notes
component
Designation Standard Certificate
Bent pipe
DN 15...900 R=4…6 x Do A335P91 ASTM A335M Manufacturer’s Seamless
Material Test 2)
Report
Tee-piece 2)
DN 20…900 ASME B16.9 A182 Gr. F91 ASTM A182M Manufacturer’s
Material Test
Report
Reducer Manufacturer’s 2)
DN 20…900 ASME B16.9 A182 Gr. F91 ASTM A182M Material Test
Report
Cap 2)
DN 20…900 ASME B16.9 A182 Gr. F91 ASTM A182M Manufacturer’s
Material Test
Report
Welding neck flange
DN 15...600 ASME B16.5, A182 Gr. F91 ASTM A182M Manufacturer’s
Class 1500 Material Test
raised face Report
Blank flange
DN 15...600 ASME B16.5, A387 Gr. 91 Cl. 2 ASTM A387M Manufacturer’s
Class 1500 Material Test
raised face Report
Bolt ANSI B18.2.1, stud bolt A193 Gr. B16 ASTM A193M Manufacturer’s Electro
Material Test galvanized
Nuts ANSI B18.2,2, heavy A194 Gr. 3 ASTM A194M Report Electro
hexagon galvanized
1) Spiral wound gasket with inner and centering rings . Metal winding strips and inner ring of 316L. Filler material of purity graphite.
2) Fittings shall stand same pressure as pipe.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 110(259)
PIPES FOR PIPE CLASSES 10C...250C No: 330-010
1(2)
14.11.2014
1 DIMENSIONS D
DN DxT
DN DxT
160C4B 250C2B
15 21.3 x 3.2 21.3 x 3.6
20 26.9 x 3.6 26.9 x 4.0
25 33.7 x 4.0 33.7 x 4.5
(32) 42.4 x 4.5 42.4 x 5.0
40 48.3 x5.0 48.3 x6,3
50 60.3 x 6.3 60.3 x 6.3
(65) 76.1 x 7.1 76.1 x 8.0
80 88.9 x 8.0 88.9 x 10.0
100 114.3 x 10.0 114.3 x 12.5
(125) 139.7 x 12.5 139.7 x 14.2
150 168.3 x 14.2 168.3 x 16.0
200 219.1 x 17.5 219.1 x 20.0
250 273 x 20.0 273 x 25.0
300 323.9 x 25.0 323.9 x 28.0
350 355.6 x 25.0
400 406.4 x 28.0
2 DESIGNATION
Name, D x T, material, standard No.
Example: Pipe, 219.1 x 6.3, P235GH, EN 10216-2
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 112(259)
ELBOWS FOR PIPE CLASSES 10C...63C No: 331-010
1(1)
14.11.2014
1 DIMENSIONS
Pressed elbow
Table 1 Dimensions according to pipe classes
DN DxT R
10C1C 25C1B 40C1B 63C2B
16C1C
15 21.3 x 2.0 38
20 26.9 x 2.3 According to According to According to 38
25 33.7 x 2.6 10C1C 10C1C 10C1C 38
(32) 42.4 x 2.6 48
40 48.3 x 2.6 48.3 x 2.9 57
50 60.3 x 2.9 60.3 x 3.2 76
(65) 76.1 x 2.9 76.1 x 3,6 95
80 88.9 x 3.2 88.9 x 4.0 114
100 114.3 x 3.6 114.3 x 4.5 152
(125) 139.7 x 4.0 139.7 x 6.3 190
150 168.3 x 4.5 168.3 x 7.1 229
200 219.1 x 6.3 219.1 x 8.0 305
250 273 x 6.3 273 x 10.0 381
300 323.9 x 7.1 323,9 x 11.0 457
350 355.6 x 5.6 355.6 x 8.0 355.6 x 8.0 533
400 406.4 x 6.3 406.4 x 8.0 406.4 x 8.0 610
(450) 457 x 6.3 457 x 8.8 457 x 8.8 686
500 508 x 6.3 508 x 11.0 508 x 11.0 762
600 610 x 6.3 610 x 12.5 610 x 12.5 914
700 711 x 7.1 711 x 14.2 1070
800 813 x 8.0 1220
900 914 x 10.0 1370
1000 1016 x 10.0 1525
1200 1220 x 12.5 1830
2 DESIGNATION
Name, D x T, R, material, standard No.
Example: Elbow, 219.1 x 6.3, 305, P235GH, EN 10253-2
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 113(259)
1 DIMENSIONS
See the following table for dimensions.
Note: The wall thickness of reducer is at least the same as the wall thicknesses of the
pipe at the bigger end of the reducer, however at least 2 mm.
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 114(259)
Wall Thickness T
DN1 DN2 D D1 L
10C1C 25C1B 40C1B
T/T1 T/T1 T/T1
350 150 355.6 168.3 330 7.1/4,5 8.0/4.5 10/4.5
200 219.1 330 7.1/6.3 8.0/6.3 10/6.3
250 273.0 330 7.1/6.3 8.0/6.3 10/6.3
300 323.9 330 7.1/7.1 8.0/7.1 10/7.1
Wall Thickness T
DN1 DN2 D D1 L
160C3B 160C4B 250C2B
T T T
25 15 33.7 21.3 51 4.5 4 4.5
20 26.9 51 4.5 4 4.5
4.5
80 32 88.9 42.4 89 10 8 10
40 48.3 89 10 8 10
50 60.3 89 10 8 10
(65) 76.1 89 10 8 10
3 DESIGNATION
Name, type, DN1/ DN2 x T/T1, material, standard No.
Example: Reducer, C, 500/ 350 x 7.1/5.6, P235GH, EN 10253-2
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 118(259)
1 DIMENSIONS
(32) (32) 42.4 42.4 48 48 2.6 2.6 2.6 2.6 2.9 2.9 3.6 3.6
(32) 25 42.4 33.7 48 48 2.6 2.6 2.6 2.6 2.9 2.6 3.6 3.2
40 40 48.3 48.3 57 57 2.6 2.6 2.6 2.6 3.2 3.2 3.6 3.6
40 (32) 48.3 42.4 57 57 2.6 2.6 2.6 2.6 3.2 2.9 3.6 3.6
50 50 60.3 60.3 64 64 2.9 2.9 2.9 2.9 3.6 3.6 4.5 4.5
50 40 60.3 48.3 64 60 2.9 2.6 2.9 2.6 3.6 2.9 4.5 4.0
(65) (65) 76.1 76.1 76 76 2.9 2.9 3.2 3.2 4.5 4.5 5.0 5.0
(65) 50 76.1 60.3 76 70 2.9 2.9 3.2 2.9 4.5 3.2 5.0 4.5
80 80 88.9 88.9 86 86 3.2 3.2 3.6 3.6 5.0 5.0 6.3 6.3
80 (65) 88.9 76.1 86 83 3.2 2.9 3.6 3.2 5.0 4.0 6.3 5.6
100 100 114.3 114.3 105 105 3.6 3.6 4.5 4.5 5.6 5.6 8.0 8.0
100 80 114.3 88.9 105 98 3.6 3.2 4.5 3.6 5.6 4.5 8.0 6.3
(125) (125) 139.7 139.7 124 124 4.0 4.0 5.0 5.0 7.1 7.1 8.0 8.0
(125) 100 139.7 114.3 124 117 4.0 3.6 5.0 4.5 7.1 5.6 8.0 7.1
150 150 168.3 168.3 143 143 4.5 4.5 6.3 6.3 8.0 8.0 10.0 10.0
150 (125) 168.3 139.7 143 137 4.5 4.0 6.3 5.0 8.0 6.3 10.0 8.0
200 200 219.1 219.1 178 178 6.3 6.3 7.1 7.1 10.0 10.0 12.5 12.5
200 150 219.1 168.3 178 168 6.3 4.5 7.1 5.6 10.0 8.0 12.5 10.0
250 250 273.0 273.0 216 216 7.1 7.1 8.8 8.8 12.5 12.5 14.2 14.2
250 200 273.0 219.1 216 203 7.1 6.3 8.8 7.1 12.5 10.0 14.2 12.5
300 300 323.9 323.9 254 254 8.0 8.0 10.0 10.0 14.2 14.2 17.5 17.5
300 250 323.9 273.0 254 241 8.0 6.3 10.0 8.8 14.2 12.5 17.5 16.0
350 350 355.6 355.6 279 279 8.8 8.8 11.0 11.0 16.0 16.0
350 300 355.6 323.9 279 270 8.8 7.1 11.0 10.0 16.0 14.2
400 400 406.4 406.4 305 305 10.0 10.0 12.5 12.5 17.5 17.5
400 350 406.4 355.6 305 305 10.0 8.0 12.5 11.0 17.5 16.0
(450) (450) 457.0 457.0 343 343 10.0 10.0 14.2 14.2 20.0 20.0
(450) 400 457.0 406.4 343 330 10.0 8.8 14.2 12.5 20.0 17.5
500 500 508.0 508.0 381 381 11.0 11.0 16.0 16.0 22.2 22.2
500 (450) 508.0 457.0 381 368 11.0 10.0 16.0 14.2 22.2 20.0
600 600 610.0 610.0 432 432 14.2 14.2 17.5 17.5 25.0 25.0
600 500 610.0 508.0 432 432 14.2 11.0 17.5 16.0 25.0 20.0
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 120(259)
Table 1 (continued)
700 700 711.0 711.0 521 521 14.2 14.2 20.0 20.0
700 600 711.0 610.0 521 508 14.2 12.5 20.0 17.5
2 DESIGNATION
Name, DN1/ DN2, T/ T1, material, standard No.
Example: Tee piece, 200/ 200, 6.3/ 6.3, P235GH, EN 10253-2
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 121(259)
1 DIMENSIONS
4 2
4 2
3
3
1
1
TYPE A TYPE A
2 DESIGNATION
Name, DN, type, material, standard No.
Example: Vent connection, DN 25, A, P235GH, 333-018
PIPING STANDARDS 9HX191450-L0008
CARBON STEEL PIPING 122(259)
3 DIMENSIONS D
DN DxT
15 21.3 x 2.11 21.3 x 2.11 21.3 x 2.11 21.3 x 2.41 21.3 x 4.78 21.3 x 2.77 21.3 x 3.73
20 26.7 x 2.11 26.7 x 2.11 26.7 x 2.11 26.7 x 2.41 26.7 x 5.56 26.7 x 2.87 26.7 x 3.91
25 33.4 x 2.77 33.4 x 2.77 33.4 x 2.77 33.4 x 2.77 33.4 x 4.55 33.4 x 2.90 33.4 x 4.55
(32) 42.2 x 2.77 42.2 x 2.77 42.2 x 2.77 42.2 x 2.77 42.2 x 4.85 42.2 x 3.56 42.2 x 4.85
40 48.3 x 2.77 48.3 x 2.77 48.3 x 2.77 48.3 x 2.77 48.3 x 5.08 48.3 x 3.68 48.3 x 5.08
50 60.3 x 2.77 60.3 x 2,77 60.3 x 2,77 60.3 x 3.18 60.3 x 5.54 60.3 x 3.91 60.3 x 6.35
(65) 73 x 2.77 73 x 2.77 73 x 2.77 73 x 3.18 73 x 5.49 73 x 4.37 73 x 7.01
80 88.9 x 3.18 88.9 x 3.18 88.9 x 3.05 88.9 x 3.58 88.9 x 5.49 88.9 x 4.78 88.9 x 7.62
100 114.3 x 3.58 114.3 x 3.58 114.3 x 3.05 114.3 x 3.96 114.3 x 6.02 114.3 x 5.56 114.3 x 8.56
(125) 141.3 x 3.96 141.3 x 3.96 141.3 x 3.18 141.3 x 4.78 141.3 x 7.14 141.3 x 6.55 141.3 x 12.70
150 168.3 x 4.37 168.3 x 4.37 168.3 x 3.40 168.3 x 5.16 168.3 x 7.92 168.3 x 7.92 168.3 x 12.70
200 219.1 x 4.78 219.1 x 4.78 219.1 x 3.96 219.1 x 6.35 219.1 x 8.74 219.1 x 9.53 219.1 x 15.09
250 273 x 5.16 273 x 5.16 273 x 4.78 273 x 7.09 273 x 11.13 273 x 11.13 273 x 18.26
300 323.9 x 5.56 323.9 x 5.56 323.9 x 4.78 323.9 x 8.38 323.9 x 11.13 323.9 x 12.70 323.9 x 20.62
350 355.6 x 5.56 355.6 x 5.56 355.6 x 5.16 355.6 x 8.74 355.6 x 11.91 355.6 x 14.27 355.6 x 22.23
400 406.4 x 5.56 406.4 x 5.56 406.4 x 5.56 406.4 x 9.53 406.4 x 12.70 406.4 x 15.88 406.4 x 25.40
(450) 457 x 6.35 457 x 6.35 457 x 6.35 457 x 10.31 457 x 14.27 457 x 17.48 457 x 28.58
500 508 x 6.35 508 x 6.35 508 x 6.35 508 x 11.13 508 x 15.09 508 x 19.05 508 x 31.75
550 559 x 6.35 559 x 6.35 559 x 7.92 559 x 12.70 559 x 17.48 559 x 20.62 559 x 34.93
600 610 x 6.35 610 x 6.35 610 x 8.74 610 x 14.27 610 x 17.48 610 x 22.23 610 x 36.53
700 711 x 7.14 711 x 7.14 711 x9.53 711 x 15.88 711 x 20.62 711 x 25.40 711 x 44.45
800 813 x 8.74 813 x 8.74 813 x 9.53 813 x 17.48 813 x 22.23 813 x 28.58 813 x 49.99
900 914 x 9.53 914 x 9.53 914 x 9,53 914 x 19,05 914 x 25.40 914 x 31.75 914 x 53.98
1000 1016 x 10.31 1016 x 10.31
1100 1118 x 12.70
1200 1219 x 12.70
2 DESIGNATION
Name, D x T, material, standard No.
Example: Pipe, 219.1 x 15.09, A335P91, ASTM A335M
PIPING STANDARDS 9HX191450-L0008
123(259)
4 NON-FERRO-ALLOY PIPING
PIPING STANDARDS 9HX191450-L0008
NON-FERRO-ALLOY PIPING 124(259)
CONTENT 1(1)
14.11.2014
1 GENERAL
This standard presents dimension standards and material specifications for piping
components in non-ferro-alloy pipe classes.
2 PIPE CLASSES
Material Remarks
Piping Dimension
components standard
Designation Standard CERTIFICATE
EN 10204-
Pipe ASTM B619, Hastelloy C ASTM B619 Grade 3.1
276
350-010
Elbow 351-010 Hastelloy C ASTM B619 Grade 3.1
276
Reducer 352-010 Hastelloy C ASTM B619 Grade 3.1
276
Tee piece 353-010 Hastelloy C ASTM B619 Grade 3.1
276
Collar EN 1092-1, Hastelloy C ASTM B619 Grade 3.1
276
PN 10…PN 16
Type 35
Loose Flange EN 1092-1, P265GH EN 10028-2 3.1 Hot dip galvanized
PN 10…PN 16,
type 02
Hex head bolt EN ISO 4014 Strength class 8.8 2.2 Hot dip galvanized
Nut EN ISO 4032 Strength class 8 2.2 Hot dip galvanized
Washer ISO 7089 Gr. A steel Hot dip galvanized
Gasket EN 1514-1 Type 2)
IBC PN10-16
Material Remarks
Piping Dimension
components standard
Designation Standard CERTIFICATE
EN 10204-
Pipe ASTM B862, Titanium ASTM B862 Grade 2 3.1
350-010
Elbow 351-010 Titanium ASTM B363 WBT2 3.1
Reducer 352-010 Titanium ASTM B363 WBT2 3.1
Tee piece 353-010 Titanium ASTM B363 WBT2 3.1
Collar EN 1092-1, Titanium ASTM B363 WBT2 3.1
PN 10…PN 25
Type 35
Loose Flange EN 1092-1, P265GH EN 10028-2 3.1 Hot dip galvanized
PN 10…PN 25,
Type 02
Hex head bolt ISO 4014 Strength class 8.8 2.2 Hot dip galvanized
Nut ISO 4032 Strength class 8 2.2 Hot dip galvanized
Washer ISO 7089 Gr. A steel Hot dip galvanized
Gasket EN 1514-1, 2)
PN10…25
Type IBC 1)
1 DIMENSIONS
DN 1) Do x s
10K 16K 25K
15 21.3 x 1.6
20 26.9 x 1.6
25 33.7 x 1.6
(32) 42.4 x 2.0
40 48.3 x 2.0
50 60.3 x 2.0 According to According to
(65) 76.1 x 2.0 10K 10K
80 88.9 x 2.0
100 114.3 x 2.0
(125) 139.7 x 2.0
150 168.3 x 2.0 168.3 x 2.6 168.3 x 2.6
200 219.1 x 2.0 219.1 x 2.6 219.1 x 3.2
250 273 x 2.0 273 x 3.2 273 x 3.6
300 323.9 x 2.6 323.9 x 3.6 323.9 x 4.0
2 DESIGNATION
1 DIMENSIONS
R 1)
DN 2)
10K 16K 25K 1.5D
15 21.3 x 2.0 25
20 26.9 x 2.0 According to According to 25
25 33.7 x 2.0 10K 10K 38
(32) 42.4 x 2.0 48
40 48.3 x 2.0 57
50 60.3 x 2.0 76
(65) 76.1 x 2.0 95
80 88.9 x 2.0 114
100 114.3 x 2.0 114.3 x 2.6 152
(125) 139.7 x 2.0 139.7 x 2.6 139.7 x3.2 190
150 168.3 x 2.0 168.3 x 3.2 168.3 x 4.0 229
200 219,1 x 2.0 219,1 x 3.2 219,1 x 4.0 305
250 273 x 2.6 273 x 3.6 273 x 5.0 381
300 323.9 x 2.6 323.9 x 4.0 323.9 x 6.3 457
2 DESIGNATION
Name, Do x s, R, material acc. to pipe class, standard No.
Example: Elbow, 114,3 x 2,0 x 190, Hastelloy C, 351-010
PIPING STANDARDS 9HX191450-L0008
NON-FERRO-ALLOY PIPING 130(259)
REDUCERS FOR PIPE CLASSES 10K…25K No: 352-010
1(3)
14.11.2014
1 DIMENSIONS
See the following table for dimensions.
Note: The wall thickness of reducer is at least the same as the wall thicknesses of the
pipe at the bigger end of the reducer, however at least 2 mm.
PIPING STANDARDS 9HX191450-L0008
NON-FERRO-ALLOY PIPING 131(259)
REDUCERS FOR PIPE CLASSES 10K…25K No: 352-010
2(3)
14.11.2014
Wall thickness T
DN1 DN2 D D1 L
1)
10K 16K 25K
3 DESIGNATION
Name, type, DN1/ DN2 x s, material according to pipe class, standard No.
Example: Reducer, C, 100/80 x 2.0, Hastelloy C, 352-010
PIPING STANDARDS 9HX191450-L0008
NON-FERRO-ALLOY PIPING 133(259)
TEE PIECES FOR PIPE CLASSES 10K...25K No: 353-010
1(3)
14.11.2014
1 DIMENSIONS
Table 1
DN1 DN2 Do1 Do2 L 10K 16K 25K
s1 / s2 s1 / s2 s1 / s2
1)
(32) (32) 42.4 42.4 48 2.0 2.0 2.0 2.0 2.0 2.0
(65) (65) 76.1 76.1 76 2.0 2.0 2.0 2.0 2.6 2.6
100 100 114.3 114.3 105 2.0 2.0 2.6 2.6 3.2 3.2
100 80 114.3 88.9 105 2.0 2.0 2.6 2.0 3.2 2.6
(125) (125) 139.7 139.7 124 2.0 2.0 3.2 3.2 4.0 4.0
(125) 100 139.7 114.3 124 2.0 2.0 3.2 2.0 4.0 3.2
150 150 168.3 168.3 143 2.6 2.6 4.0 4.0 5.0 5.0
150 (125) 168.3 139.7 143 2.6 2.6 4.0 3.2 5.0 4.0
200 200 219.1 219.1 178 3.2 3.2 5.0 5.0 6.3 6.3
200 150 219.1 168.3 178 3.2 2.6 5.0 3.2 6.3 5.0
250 250 273 273 216 4.0 4.0 6.3 6.3 8.0 8.0
250 200 273 219.1 216 4.0 2.6 6.3 4.0 8.0 6.3
300 300 323.9 323.9 254 5.0 5.0 8.0 8.0 10.0 10.0
300 250 323.9 273 254 5.0 3.2 8.0 5.0 10.0 6.3
PIPING STANDARDS 9HX191450-L0008
NON-FERRO-ALLOY PIPING 135(259)
TEE PIECES FOR PIPE CLASSES 10K...25K No: 353-010
3(3)
14.11.2014
2 DESIGNATION
Name, DN1/ DN2, s1/ s2, material according to pipe class , standard No.
Example: Tee piece, 100/ 80, 2.6/ 2.0, Hastelloy C, 353-010
PIPING STANDARDS 9HX191450-L0008
NON-FERRO-ALLOY PIPING 136(259)
1 DIMENSIONS
DN 50
DN 40
Note: 1) Material and pipe fittings are according to each pipe class.
2 DESIGNATION
1 DIMENSIONS
Note: 1) Material and pipe fittings are according to each pipe class.
2 DESIGNATION
Name, DN, type, material, standard No.
Example: Vent connection, DN 25, A, Hastelloy C, 355-015
PIPING STANDARDS 9HX191450-L0008
138(259)
5 PLASTIC PIPING
PIPING STANDARDS 9HX191450-L0008
PLASTIC PIPING 139(259)
CONTENT 1(1)
14.11.2014
10S2A DN 25...1400 2
10S2D DN 25…1400 3
16S2A DN 25…500 4
25S2A DN 25…300 5
PVC-C piping:
10L4B DN 25...300 7
Elbow 90°
DN 25...DN 400 SFS 5165. PN 10 GRP - 3.1 Bell and spigot type 3)
DN 25...DN 1400 SFS 5167. PN 10 Type A/B GRP - 3.1 Laminate ends
Reducer
DN 25...DN 400 SFS 5165. PN 10 GRP - 3.1 Bell and spigot type 3)
DN 25…DN 1000 SFS 5168. PN 10 GRP - 3.1 Laminate ends
DN 1100…DN 1400 Manufacturer‘s design GRP - 3.1 Laminate ends
T-Piece
DN 25…DN 400 SFS 5165. PN 10 GRP - 3.1 Bell and spigot type 3)
DN 25…DN 600 SFS 5169. PN 10 GRP - 3.1 Laminate ends
DN 700…DN 1400 Manufacturer’s design GRP - 3.1 Laminate ends
Collar
DN 25…DN 400 SFS 5165. PN 10 GRP - 3.1 Bell and spigot type 3)
DN 25…DN 1000 SFS 5174. PN 10 GRP - 3.1 Laminate ends
DN 1200…DN 1400 Manufacturer’s design GRP - 3.1 Laminate ends
Loose flange
DN 15...DN 1000 SFS 5174. PN 10 S235JR EN 10025 2.2 Hot dip galvanized
DN 1200…DN 1400 Manufacturer’s design S235JR EN 10025 2.2 Hot dip galvanized
Elbow 90°
DN 25...DN 400 SFS 5165, PN 10 GRP - 3.1 Bell and spigot type 3) 4)
DN 25...DN 1400 SFS 5167, PN 10 ,Type A/B GRP - 3.1 Laminate ends 4)
Reducer
DN 25...DN 400 SFS 5165, PN 10 GRP - 3.1 Bell and spigot type 3) 4)
DN 25...DN 1000 SFS 5168, PN 10 GRP - 3.1 Laminate ends 5)
DN 1100…DN 1400 Manufacturer’s design GRP 3.1 Laminate ends 5)
T-Piece
DN 25…DN 400 SFS 5165, PN 10 GRP - 2.2 Bell and spigot type 3) 4)
DN 25…DN 600 SFS 5169, PN 10 GRP - 2.2 Laminate ends 4)
DN 700…DN 1400 Manufacturer’s design GRP - 2.2 Laminate ends 4)
Collar
DN 25…DN 400 SFS 5165, PN 10 GRP - 3.1 Bell and spigot type 3) 4)
DN 25…DN 1000 SFS 5174, PN 10 GRP - 3.1 Laminate ends 4)
DN 1200…DN 1400 Manufacturer’s design GRP - 3.1 Laminate ends 4)
Loose flange
DN 15...DN 1000 SFS 5174, PN 10 S235JR EN 10025 2.2 Hot dip galvanized
DN 1200…DN 1400 S235JR EN 10025 2.2 Hot dip galvanized
Washer
ISO 7089 Gr. A S235JR EN 10025-2 Hot dip galvanized
Gasket
DN 25…DN 1000 SFS 5216, PN 10, Type B 2)
DN 1200…DN 1400 Manufacturer’s design
1) Vinylester based glass fibre reinforced plastic with thick barrier layer
2) Gasket material depends on flow substance. See 9HX191450-L0007 “Technical Specification for Piping
Materials and Valve Selection”
3) Bell and spigot fittings are allowed on size range DN 25-400 after Purchaser’s approval.
4) The thickness of protective layer shall be minimum 4 mm
PIPING STANDARDS 9HX191450-L0008
PLASTIC PIPING 143(259)
Piping Dimension
Material
component standard Remarks
Designation Standard Certificate
EN 10204-
Pipe
DN 25...DN 500 SFS 5166, PN 16 GRP 1) - 3.1 Laminate ends
-
Elbow 90°
DN 25...DN 400 SFS 5165, PN 16 GRP - 3.1 Bell and spigot type 3)
SFS 5167, PN 16, - Laminate ends
DN 25...DN 500 GRP 3.1
Type A/B
Reducer
DN 25...DN 400 SFS 5165, PN 16 GRP - 3.1 Bell and spigot type 3)
SFS 5168, PN 16 - 3.1 Laminate ends
DN 25...DN 500 GRP
T-Piece
DN 25…DN 400 SFS 5165, PN 16 GRP - 3.1 Bell and spigot type 3)
SFS 5169, PN 16 - Laminate ends
DN 25…DN 500 GRP 3.1
Collar
GRP - 3.1 Bell and spigot type 3)
DN 25…DN 400 SFS 5165, PN 16
DN 25…DN 500 SFS 5174, PN 16 GRP - 3.1 Laminate ends
Loose flange
DN 15...DN 500 SFS 5175, PN 16 S235JR EN 10025 2.2 Hot dip galvanized
-
Blank flange 340-012, PN 16 GRP 2.2
Washer
ISO 7089 Gr. A S235JR EN 10025-2 Hot dip galvanized
Gasket
SFS 5216, PN 16, 2)
Type B
Piping Dimension
Material
component standard Remarks
Designation Standard Certificate
EN 10204-
Pipe
DN 25...DN 300 SFS 5166, PN 25 GRP 1) - 3.1 Laminate ends
-
Elbow 90°
DN 25...DN 300 SFS 5167, PN 25, GRP - 3.1 Laminate ends
Type A/B
Reducer
DN 25...DN 300 SFS 5168, PN 25 GRP - 3.1 Laminate ends
T-Piece
DN 25…DN 300 SFS 5169, PN 25 GRP - 3.1 Laminate ends
Flange
DN 25…DN 300 SFS 5176, PN 25 GRP - 3.1 Laminate ends
Collar
SFS 5174, PN 25 GRP - 3.1 Laminate ends
DN 25…DN 300
Loose flange
DN 15...DN 300 SFS 5176, PN 25 S235JR EN 10025 2.2 Hot dip galvanized
-
Blank flange 340-012, PN 25 GRP 2.2
DN 25…DN 600
Hex head bolt Strength class
ISO 4014 8.8 ISO 898-1 2.2 Hot dip galvanized
Washer
EN ISO 887 S235JR Hot dip galvanized
Gasket
SFS 5216, PN 25, 2)
Type B
Piping Dimension
Material
component standard Remarks
5)
Designation Standard Certificate
EN 10204-
Pipe
dn 20...800 4) ISO 15494, PN 10/ HD-PE ISO 15494 3.1
water 100/SDR 17
Elbow
dn 20...800 DIN 16963 B1, Type HD-PE ISO 15494 3.1 Radius R = 1,5 x dn
100/SDR 17 3)
1,5 x dn, PN10/water
Reducer
dn 20...800 DIN 16963, PN10/ HD-PE ISO 15494 3.1 3)
100/SDR 17
water
T-Piece
dn 20..800 DIN 16963, Type T1 HD-PE ISO 15494 3.1 3)
100/SDR 17
and T5, PN 10/ water
Branch/ Saddle
Loose backing
flange
DN 15..800 ISO 15494, PN 10 P245GH EN 10028-2 3.1 For butt fusion flange
Drilling according to adaptor, hot dip
EN 1092-1 galvanized
Hex head bolt Strength
ISO 4014 class ISO 898-1 2.2 Hot dip galvanized
8.8
Nut Strength
ISO 4032 class EN 20898-2 2.2 Hot dip galvanized
8
Washer
ISO 7089 Gr. A S235JR EN 10025-2 Hot dip galvanized
Gasket EN 1514 PN 10 2)
Type FF
Piping Dimension
Material
components standard Remarks
Designation Standard Certificate
EN 10204-
Pipe
DN 25...DN 300 ISO 15493, PN 10 PVC-C 3.1
Elbow
DN 25...DN 300 DIN 8063, PN 10 PVC-C 3.1
Reducer
DN 25...DN 300 DIN 8063, PN 10 PVC-C 3.1
T-Piece
DN 25...DN 300 DIN 8063, PN 10 PVC-C 3.1
Collar
DN 25...DN 300 ISO 15493, PN 10 PVC-C 3.1
Loose flange
DN 25...DN 300 ISO 15493 PN 10 3) P245GH EN 10028-2 2.2 Hot dip galvanized
Drilling according to
EN 1092-1
Socket
DN 25...DN 300 DIN 8063 PVC-C - 3.1
Nut Strength
ISO 4032 class EN 20898-2 2.2 Hot dip galvanized
8
Washer
ISO 7089 Gr. A S235JR EN 10025-2 Hot dip galvanized
Gasket EN 1514 PN 10
Type FF 2)
Piping Dimension
Material
component standard Remarks
Designation Standard 5) Certificate
EN 10204-
Pipe
DN 25...DN 300 ISO 15493, PN 10 PVC-C/GRP 3.1
+ GRP reinforcement
Elbow
DN 25...DN 300 DIN 8063, PN 1 PVC-C/GRP 3.1 + GRP reinforcement
Reducer
DN 25...DN 300 DIN 8063, PN 10 PVC-C/GRP 3.1 + GRP reinforcement
T-Piece
DN 25...DN 300 DIN 8063 , PN 10 PVC-C/GRP 3.1 + GRP reinforcement
Collar
DN 25...DN 300 ISO 15493, PN 10 PVC-C/GRP 3.1 + GRP reinforcement
Loose flange
DN 25...DN 300 ISO 15493 PN 10 3) P245GH EN 10028-2 2.2 Hot dip galvanized
Drilling according to
EN 1092-1
Socket
DN 25...DN 300 DIN 8063 , PN 10 PVC-C/GRP - 3.1 + GRP reinforcement
Washer
ISO 7089 Gr. A S235JR EN 10025-2 Hot dip galvanized
Gasket EN 1514 PN 10
Type FF 2)
1.6 MPa 20 °C
Piping Dimension
Material
component standard Remarks
Designation Standard Certificate
EN 10204-
Pipe
DN 25...DN 200 PTFE/ ASTM 3.1 Seamless lined with
EN 10216-2, PTFE, vacuum
330-010, PN 16 P235GH D4894/
resistance
EN 10216-2
Ends with welding
neck flanges
Elbow 90°
EN 10253-2, Lined with PTFE,
DN 25...DN 200 PTFE/ ASTM 3.1
331-010, PN 16 vacuum resistance
P235GH D4894/
EN 10253-2 R = 1.5Do
Ends with welding
neck flanges
Reducer
DN 25...DN 200 EN 10253-2, PTFE/ ASTM 3.1 Lined with PTFE,
332-010, PN 16 D4894/ vacuum resistance
P235GH
EN 10253-2 Ends with welding
neck flanges
T-Piece
DN 25…DN 200 EN 10253-2 PTFE/ ASTM 3.1 Lined with PTFE,
333-010, PN 16 D4894/ vacuum resistance
P235GH
EN 10253-2 Ends with welding
neck flanges
Welding neck
flange EN 1092-1, P245GH EN 10028-2 3.1 Lined with PTFE,
DN 25...DN 200 type 11, PN 16 vacuum resistance
Washer
ISO 7089 Gr. A S235JR EN 10025-2 Hot dip galvanized
1) Gasket material depends on flow substance. See “9HX191450-L0007 “Technical Specification for Piping Materials and Valve Selections”.
PIPING STANDARDS 9HX191450-L0008
PLASTIC PIPING 149(259)
1 DIMENSIONS
Drilling pattern shall be according to standard EN 1092-1, PN10…PN 25.
2 DESIGNATION
Name, DN, pressure class of pipe class, material of the flange, material of lining plate,
standard No.
Example: Blank flange, DN 250, PN 16, GRP, 340-012
PIPING STANDARDS 9HX191450-L0008
PLASTIC PIPING 151(259)
CAP 10S…25S No: 340-014
1(1)
14.11.2014
1 DIMENSIONS
DN=Di R r h H
mm mm mm mm
40 32 6 10 20
50 40 8 10 23
(65) 52 10 15 32
80 64 12 15 35
100 80 15 15 40
(125) 100 19 15 47
150 120 23 15 53
200 160 31 20 71
250 200 39 20 84
300 240 46 20 96
350 280 54 20 109
400 320 62 20 122
(450) 360 69 20 135
500 400 77 20 147
600 480 92 20 173
700 560 108 20 198
800 640 123 20 224
900 720 139 20 249
1000 800 154 20 274
Notes:
1) Cap wall thickness T is same as the pipe wall thickness in the same pipe
class.
2 DESIGNATION
362-010 Seal water connection for pump. Stuffing box or mechanical seal
with flow-through. Principal arrangement
362-011 Seal water connection for pump. Stuffing box with inflow.
Principal arrangement
362-012 Seal water connection for pump. Stuffing box or mechanical seal.
Support of sealing water unit
362-013 Seal water connection for pump. Stuffing box or mechanical seal
with flow-through. Principal arrangement
1 DIMENSIONS
4 Check valve
3 Reducer
Part Description
2 DESIGNATION
Name, standard No.
Example: Steam trap arrangement, 360-010
PIPING STANDARDS 9HX191450-L0008
STEAM TRAPS, SEAL WATER AND SERVICE PIPING ARRANGEMENT 155(259)
STEAM TRAPS No: 360-012
MEDIUM AND LOW PRESSURE STEAM PIPING 1(1)
TYPICAL ARRANGEMENT OUTDOORS 14.11.2014
1 DIMENSIONS
3 Reducer
Part Description
Notes: Pipe end to the cooling pit must not reach to the water.
Nominal size of the piping at least DN 50.
2 DESIGNATION
1 DIMENSIONS
D1 STEAM PIPE
D2
L
DN1
TO STEAM TRAP
DN2
D1 50 65 80 100 125 150 200 250 300 350 400 450 500 600
mm 60.3 76.1 88.9 114.3 139.7 168.3 219.1 273.0 323.9 355.6 406.4 457.2 508.0 610.0
mm 33.7 33.7 60.3 60.3 88.9 114.3 168.3 168.3 168.3 219.1 219.1 273.0 273.0 323.9
DN1 25 25 25 25 25 25 25 22 25 25 25 25 40 40
DN2 25 25 25 40 40 40 40 50 50 50 50 50 50 50
2 DESIGNATION
1 DIMENSIONS
D1 50 65 80 100 125 150 200 250 300 350 400 450 500 600
mm
60.3 76.1 88.9 114.3 139.7 168.3 219.1 273.0 323.9 355.6 406.4 457.2 508.0 559 610.0
D2 25 25 50 80 80 100 150 150 150 200 200 250 250 300 300
mm
33.7 33.7 60.3 88.9 88.9 114.3 168.3 168.3 168.3 219.1 219.1 273.0 273.0 323.9 323.9
DN1 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15
DN2 20 25 25 40 40 40 40 50 50 50 50 50 50 50 50
2 DESIGNATION
3 DIMENSIONS
1
4
4 DESIGNATION
5 DIMENSIONS
3
Piping delivery limit
PIPING STANDARDS 9HX191450-L0008
STEAM TRAPS, SEAL WATER AND SERVICE PIPING ARRANGEMENT 162(259)
SEAL WATER CONNECTION FOR PUMP No: 362-011
STUFFING BOX WITH INFLOW 2(2)
PRINCIPAL ARRANGEMENT 14.11.2014
6 DESIGNATION
7 ARRANGEMENT
8 DESIGNATION
9 DIMENSIONS
5 1 Hose coupling DN 15
10 DESIGNATION
11 DIMENSIONS
1 2 3
Valve DN 25
Hose connection DN 20
1100
DN 25
2 3
Valve DN 25
Hose connection DN 20
4
DN 40
1100
Valve DN 25
Hose connection DN 20
2 3 4
1100
PIPING STANDARDS 9HX191450-L0008
STEAM TRAPS, SEAL WATER AND SERVICE PIPING ARRANGEMENT 167(259)
COMPRESSED AIR SUPPLY SYSTEM DN 20 No: 365-011
2(2)
14.11.2014
4 3 Hose connection
R ¾” external thread R 1”
12 DESIGNATION
13 DIMENSIONS
X – X Specification limit
14 DESIGNATION
15 DIMENSIONS
Hose reel, hose 1", 30 m
Connection R 1 with int. thread
8 9 1 2 3 4
560
Valve DN 40
420
635
1200
1100
7 6 5 DN 80
2 3 4
Valve DN 40
560
420
635
1200
1100
Valve DN 40
560
420
635 2 3 4
650
A
1100
1200
A A
PIPING STANDARDS 9HX191450-L0008
STEAM TRAPS, SEAL WATER AND SERVICE PIPING ARRANGEMENT 170(259)
FIRE HYDRANT DN 40 WITH HOSE REEL, INDOORS No: 367-010
2(2)
14.11.2014
16 DESIGNATION
Name, DN, standard No.
Example: Fire hydrant indoors, DN 40, 367-010
PIPING STANDARDS 9HX191450-L0008
STEAM TRAPS, SEAL WATER AND SERVICE PIPING ARRANGEMENT 171(259)
FIRE HYDRANT 2 x DN 80, OUTDOORS No: 367-011
1(2)
14.11.2014
17 DIMENSIONS
1 10 5
11 2
1 12
4
3 9
625
8
1000
7
6
PIPING STANDARDS 9HX191450-L0008
STEAM TRAPS, SEAL WATER AND SERVICE PIPING ARRANGEMENT 172(259)
FIRE HYDRANT 2 x DN 80, OUTDOORS No: 367-011
2(2)
14.11.2014
18 DESIGNATION
19 DIMENSIONS
Notes: Pipe parts under earth shall be handled with bitumen, other parts shall be painted.
PIPING STANDARDS 9HX191450-L0008
STEAM TRAPS, SEAL WATER AND SERVICE PIPING ARRANGEMENT 174(259)
FIRE HYDRANT 4 x DN 80, OUTDOOR AREA No: 367-012
2(2)
14.11.2014
20 DESIGNATION
370-005 Pipe hanger for uninsulated stainless steel pipes DN 6…DN 150
372-013 Anchorage
372-032 Clevis
21 APPLICATION
Hot, insulated carbon and stainless steel piping
22 CLAMP MATERIAL
Flat bar, S235JR, EN 10025-2 or equivalent.
24 OPERATION TEMPERATURE
T 300 C
25 SURFACE TREATMENT
Clamp: hot dip galvanized
Table
Flat Insulation
thickness
Pipe d1 Dimensions Bolt Weight 1)
bar 2)
DN Do ML D a b c e g f d hxs mm kg
10 17.2 18 42 67 7,5 46 76 7 7 20 x 3 M6 x 25 30 0,12
15 21.3 22 56 74 9,5 46 85 7 10 25 x 5 M8 x 30 30 0,28
20 26.9 27 62 77 9,5 46 91 7 10 25 x 5 M8 x 30 30 0,30
25 33.7 10 34 69 81 9,5 46 98 7 10 30 x 5 M8 x 30 30 0,38
32 42.4 (2000) 43 85 89 15 46 110 7 12 30 x 5 M10 x 40 40 0,51
40 48.3 49 89 91 15 46 115 7 12 30 x 5 M10 x 40 40 0,53
50 60.3 12 61 101 105 15 54 135 7 12 30 x 5 M10 x 40 40 0,61
65 76.1 (3500) 77 126 117 16 54 156 7 14 30 x 6 M12 x 40 40 0,83
80 88.9 89 139 124 16 54 168 7 14 30 x 6 M12 x 40 40 0,89
100 114.3 115 174 157 22 70 215 12 18 40 x 8 M16 x 50 60 2,00
125 139.7 16 140 200 170 22 70 240 12 18 40 x 8 M16 x 50 60 2,20
150 168.3 (8000) 169 229 185 22 70 269 12 18 40 x 8 M16 x 50 60 2,50
200 219.1 220 283 212 22 70 322 12 18 50 x 8 M16 x 50 60 3,50
250 273.0 20 273 348 244 30 70 381 14 23 60 x 8 M20 x 60 70 5,20
300 323.9 (15000) 324 398 285 30 86 447 14 23 60 x 8 M20 x 60 70 6,00
350 355.6 356 432 302 30 86 480 14 23 60 x 8 M20 x 60 70 6,40
400 406.4 407 498 335 36 86 539 18 27 70 x 10 M24 x 70 90 11,00
450 457.0 24 457 548 378 36 104 607 18 27 70 x 10 M24 x 70 90 11,40
500 508.0 (22000) 508 600 404 36 104 658 18 27 70 x 10 M24 x 70 90 12,00
The allowable load of the whole pipe hanger structure is determined by the weakest part of the
structure (rod or pipe clamp).
27 DESIGNATION
28 APPLICATION
Uninsulated carbon and stainless steel piping.
29 CLAMP MATERIAL
Flat bar, S235JR, EN10025-2 or equivalent
31 OPERATION TEMPERATURE
t = 20 C…70 C
32 SURFACE TREATMENT
Clamp: hot dip galvanized
Bolts and nuts: hot dip galvanized
Notes: (* ) Flat bar to DN 500, U-bar (U100) for DN 600…1200 see standard 370-
017
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 182(259)
PIPE HANGER DN 10…DN 1200 No: 370-004
2(3)
14.11.2014
Table ML = max. load (N)
Insulation Weight
Flat
Pipe d1 Dimensions Bolt thickness 1)
bar 2)
DN Do ML D a b c g f d hxs mm kg
700 711.0 30 711 825 413 27,5 768 22 33 U-bar M30 x 80 100 28,00
800 813.0 (40000) 813 925 463 27,5 869 22 33 U100 M30 x 80 100 31,00
900 914.0 914 1030 515 27,5 972 22 33 (100x50) M30 x 80 100 35,00
1000 1016.0 1016 1130 565 27,5 1073 22 33 M30 x 80 100 38,00
1200 1220.0 1220 1330 665 30 1275 22 33 M30 x 80 100 45,00
The allowable load of the whole pipe hanger structure is determined by the weakest part of the
structure (rod or pipe clamp).
34 DESIGNATION
35 APPLICATION
Clamps according to this standard are to be used for supporting of pipes
36 MATERIAL
Clamp, sleeve and threaded rod S235JR, EN 10025-2 or equivalent.
38 OPERATION TEMPERATURE
t = 20 C …70 C
39 DESIGNATION
Hanger, DN, type, 370-005
40 HANGER DIMENSIONS
Part 1, clamp
Fig. 3 Clamp
Table 2
Part 2, sleeve
Fig. 4 Sleeve
Table 3
Sleeve, dimension, mm Weight
DN d s min d1 c b l l1 l2 kg/ 100 pcs
6 M6 1.0 9 7 12 35 15 10 0.6
8
10
15 M6 1.0 9 7 12 35 15 10 0.6
20
25
32 M8 1.5 9 9 15 40 17 12 0.9
40
50
65 M8 1.5 9 9 15 40 17 12 0.9
80 M10 11 11 18 45 20 15 1.9
100
125 M12 2 13 14 20 55 25 3.5
150
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 188(259)
PIPE CLAMP FOR WELDING DN 10…DN 1200 No: 370-006
1(3)
14.11.2014
41 APPLICATION
This clamp is to be welded straight on to any steel structure.
The clamp is suitable for both insulated and uninsulated carbon and stainless steel piping.
42 CLAMP MATERIAL
Flat bar S235JR, EN 10025-2 or equivalent
44 OPERATION TEMPERATURE
t 300 C
45 SURFACE TREATMENT
Clamps hot-dip-galvanized. Damaged surface treatment shall be painted after welding.
46 DESIGNATION
Pipe clamp, DN, 370-006. Where DN = Nominal size of the pipe.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 189(259)
PIPE CLAMP FOR WELDING DN 10…DN 1200 No: 370-006
2(3)
14.11.2014
48 APPLICATION
This sliding support is used for insulated carbon and stainless steel piping. It can be free
standing or guided (see 372-015). Pipe clamps are described on standard 370-016.
49 ADDITIONAL REQUIREMENTS
When this sliding support is used as a component of an anchorage the assembly
instructions given on standard 372-013 shall be used and the designation 2 shall be given
in requisition and parts lists.
Guides number and type of guides shall be given separately in parts lists.
Because of thermal expansion the length of the support shoe L shall be checked case by
case.
50 MATERIAL
Flat bar S235JR, EN 10025-2 or equivalent
52 OPERATION TEMPERATURE
t 300 C
53 SURFACE TREATMENT
Support: hot dip galvanised
Bolts and nuts: hot dip galvanised
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 192(259)
SLIDING SUPPORT FOR INSULATED No: 370-011
PIPING DN 10…DN 150 2(3)
14.11.2014
54 DESIGNATION
DESIGNATION 1:
Sliding support, DN, 370-011
Where DN = Nominal size of the pipe
DESIGNATION 2:
Anchorage, DN, 370-011
Where DN = Nominal size of the pipe
1)If needed pipe clamps can be fixed to angle a in respect to the horizontal plane. The
maximum recommended angle=45°.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 193(259)
SLIDING SUPPORT FOR INSULATED No: 370-011
PIPING DN 50…DN 150 3(3)
14.11.2014
55 LOADS ON SUPPORTS
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
56 APPLICATION
This sliding support is used for insulated carbon and stainless steel piping. It can be free
standing or guided (see 372-015). Pipe clamps are described on a standard 370-016.
57 ADDITIONAL REQUIREMENTS
When this sliding support is used as a component of an anchorage the assembly
instruction given on standard 372-013 shall be used and the designation 2 shall be given
in requisition and parts lists.
Guides number and type of guides shall be given separately in parts lists.
Because of thermal expansion the length of the support shoe L shall be checked case by
case.
58 MATERIAL
Flat bar S235JR, EN 10025-2 or equivalent
60 OPERATION TEMPERATURE
t 300 C
61 SURFACE TREATMENT
Support: hot dip galvanised
Bolts and nuts: hot dip galvanised
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 195(259)
SLIDING SUPPORT FOR INSULATED No: 370-012
PIPING DN 200…DN 500 2(3)
14.11.2014
62 DESIGNATION
DESIGNATION 1:
Sliding support, DN, 370-012
Where DN = Nominal size of the pipe
Pipe slide
If needed pipe clamps can be fixed to angle a in respect to the horizontal plane. The maximum
recommended angle=45°.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 196(259)
SLIDING SUPPORT FOR INSULATED No: 370-012
PIPING DN 200…DN 500 3(3)
14.11.2014
DN a b c d e f g i j n o p t
300 432 160 178 229 223 170 374 37 90 206 150 50 8
350 430 160 178 240 222 186 388 36 95 204 150 50 10
400 420 160 172 250 221 214 414 34 100 202 150 50 10
450 420 160 172 265 221 239 439 33 108 201 150 50 10
500 418 160 172 300 228 264 462 28 113 201 175 75 12
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 197(259)
SLIDING SUPPORT FOR INSULATED No: 370-012
PIPING DN 200…DN 500 3(3)
14.11.2014
63 LOADS ON SUPPORTS
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
64 APPLICATION
This sliding support is used for insulated carbon and stainless steel piping. It can be free
standing or guided (see 372-015). Pipe clamps are described on a standard 370-017.
65 ADDITIONAL REQUIREMENTS
When this sliding support is used as a component of an anchorage the assembly
instructions given on standard 372-013 shall be used and the designation 2 shall be given
in requisition and parts lists.
Guides number and type of guides shall be given separately in parts lists.
Because of thermal expansion the length of the support shoe L shall be checked case by
case.
66 MATERIAL
Flat bar S235JR, EN 10025-2 or equivalent
68 OPERATION TEMPERATURE
t 300
69 SURFACE TREATMENT
Support: hot dip galvanised
Bolts and nuts: hot dip galvanised
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 199(259)
70 DESIGNATION
DESIGNATION 1:
Sliding support, DN, 370-014
Where DN = Nominal size of the pipe
DESIGNATION 2:
Anchorage, DN, 370-014
Pipe slide
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 200(259)
Pipe Dimensions of pipe support Maximum
DN Do D l H h k m t r Weight insulation
mm mm mm mm mm mm mm mm kg thickness s2
600 610.0 610 780 555 250 330 140 16 30 105 240
700 711.0 712 880 606 250 380 140 16 30 117 240
800 813.0 813 980 657 250 430 140 16 30 129 240
900 914.0 915 1085 748 290 490 145 20 40 166 280
1000 1016.0 1016 1185 798 290 540 145 20 40 180 280
1200 1220.0 1220 1390 900 290 590 145 20 40 202 280
If needed pipe clamps can be fixed to angle a in respect to the horizontal plane. The maximum
recommended angle=45°.
SLIDING SUPPORT FOR INSULATED No: 370-014
PIPING DN DN 600…DN 1200 3(4)
14.11.2014
End plate
Stiffening plate
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 201(259)
DN a b c d e f g i j n o p q t
600 384 170 155 298 258 311 539 16 107 231 225 85 - 16
700 384 170 155 348 263 362 590 19 132 231 225 85 - 16
800 384 170 155 398 269 413 641 21 149 232 225 100 150 16
900 380 170 153 450 313 464 728 19 103 281 275 85 175 20
1000 380 170 153 500 318 514 778 21 114 282 275 100 200 20
1200 380 170 153 550 319 616 880 20 119 284 275 100 225 20
71 LOADS ON SUPPORTS
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
72 APPLICATION
These pipe clamps are used for sliding supports described in separate standards.
73 MATERIAL
Flat bar, S235JR, EN 10025-2 or equivalent
75 OPERATION TEMPERATURE
T 300 C
76 SURFACE TREATMENT
Hot dip galvanised Sliding support:.
Bolts and nuts: hot dip galvanized
77 DIMENSIONS
DN 10…DN 500
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 204(259)
PIPE CLAMPS FOR SLIDING SUPPORTS DN 10…DN 500 No: 370-016
2(2)
14.11.2014
Table
78 APPLICATION
These pipe clamps are used for sliding supports described in separate standard.
79 MATERIAL
Flat bar and steel profiles S235JR, EN 10025-2 or equivalent.
81 OPERATION TEMPERATURE
t 300 C
82 SURFACE TREATMENT
Sliding support: Hot dip galvanized
Bolts and nuts: Hot dip galvanized
83 DESIGNATION:
Name, Do, 370-017, where Do = Outside diameter of the pipe
Example: Clamp, 610, 370-017.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 206(259)
PIPE CLAMPS FOR SLIDING SUPPORTS DN 600…DN 1200 No: 370-017
2(2)
14.11.2014
DN Do D a l kg
600 610 610 720 780 M30 x 80 24
700 711 712 825 885 M30 x 80 28
800 813 813 925 985 M30 x 80 31
900 914 915 1030 1090 M30 x 80 35
1000 1016 1016 1130 1190 M30 x 80 38
1200 1220 1220 1330 1390 M30 x 80 45
84 APPLICATION
This sliding support is used for uninsulated carbon and stainless steel piping. It can be
free standing or guided (see 372-015). Pipe clamps described on standard 370-016.
85 ADDITIONAL REQUIREMENTS
When this sliding support is used as a component of an anchorage the assembly
instructions given on standard 370-013 shall be used and the designation 2 shall be given
in requisition and parts lists.
Guides number and type of guides shall be given separately in parts lists.
86 MATERIAL
Flat bar and steel profiles S235JR, EN 10025-2 or equivalent.
88 OPERATION TEMPERATURE
t = 20 C….70 C
89 SURFACE TREATMENT
Sliding support: hot dip galvanized.
Bolts and nuts: hot dip galvanized
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 208(259)
SLIDING SUPPORT FOR UNINSULATED PIPING DN 10…DN 150 No: 370-018
2(3)
14.11.2014
90 DESIGNATION
DESIGNATION 1:
DESIGNATION 2:
Pipe slide
1) If needed pipe clamps can be fixed to angle a in respect to the horizontal plane. The maximum
recommended angle=45°.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 209(259)
SLIDING SUPPORT FOR UNINSULATED PIPING DN 10…DN 150 No: 370-018
3(3)
14.11.2014
91 LOADS ON SUPPORTS
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
92 APPLICATION
This sliding support is used for uninsulated carbon and stainless steel piping. It can be
free standing or guided (see support 372-015). Pipe clamps are described on standard
370-016.
93 ADDITIONAL REQUIREMENTS
When this sliding support is used as a component of an anchorage the assembly
instruction given on standard 372-013 shall be used and the designation 2 shall be given
in requisition and parts lists.
Guides number and type of guides shall be given separately in parts lists.
94 MATERIAL
Flat bar and steel profiles S235JR, EN 10025-2 or equivalent.
96 OPERATION TEMPERATURE
t = 20 C…70 C
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 211(259)
SLIDING SUPPORT FOR UNINSULATED PIPING DN 200…DN 500 No: 370-019
2(3)
14.11.2014
97 SURFACE TREATMENT
Support, hot dip galvanised
Bolts and nuts: hot dip galvanised
98 DESIGNATION
DESIGNATION 1:
Sliding support, DN, 370-019
Where DN = Nominal size of the pipe
DESIGNATION 2:
Anchorage, DN, 370-019
Where DN = Nominal size of the pipe
Pipe slide
1) If needed pipe clamps can be fixed to angle a in respect to the horizontal plane. The maximum
recommended angle=45°.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 212(259)
SLIDING SUPPORT FOR UNINSULATED PIPING DN 200…DN 500 No: 370-019
3(3)
14.11.2014
99 LOADS ON SUPPORTS
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
100 APPLICATION
This sliding support is used for uninsulated carbon and stainless steel piping. It can be
free standing or guided (see 372-015). Pipe clamps are described on standard 370-017.
Guides number and type of guides shall be given separately in parts lists.
102 MATERIAL
Flat bar and steel profiles S235JR, EN 10025-2 or equivalent.
106 DESIGNATION
DESIGNATION 1:
Sliding support, DN, 370-020
Where DN = Nominal size of the pipe
DESIGNATION 2:
Anchorage, DN, 370-020
Where DN = Nominal size of the pipe
DN Do D l H h k e Laxbxs
mm mm mm mm mm mm mm mm kg
600 610 610 780 381 76 380 280 100 x 50 x 8 61
700 711 712 880 432 76 530 400 130 x 65 x 10 75
800 813 813 980 483 76 570 440 130 x 65 x 10 82
900 914 915 1085 534 76 690 540 150 x 75 x 11 94
1000 1016 1016 1185 584 76 710 560 150 x 75 x 11 100
1200 1220 1220 1390 686 76 770 620 150 x 75 x 11 120
1) If needed pipe clamps can be fixed to angle a in respect to the horizontal plane. The maximum
recommended angle=45°.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 215(259)
SLIDING SUPPORT FOR UNINSULATED PIPING DN 600…DN 1200 No: 370-020
2(2)
14.11.2014
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
108 APPLICATION
Cold, uninsulated carbon and stainless steel piping
109 MATERIAL
113 DESIGNATION
PIPE SUPPORT
114 APPLICATION
Threaded rod shall be welded to the composite eye rod which gives necessary total length
for the rod. This total length is expressed as described in pipe hanger standards.
115 MATERIAL
S235JR, EN 10025-2 or equivalent.
119 DESIGNATION
Threaded rod, d, 372-008.
Where d = Diameter of the rod.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 219(259)
THREADED ROD No: 372-008
2(2)
14.11.2014
120 APPLICATION
This eye is used for pipe hangers described in separate standards and shall be welded to
the composite eye rod.
121 MATERIAL
Flat bar S235JR, EN 10025-2
124 DESIGNATION
Eye, d, 372-009
Where d = Diameter of the rod.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 221(259)
EYE FOR HANGER ROD No: 372-009
2(2)
14.11.2014
Table
Dimensions Weight
DN d d1 c k l bxt kg
10-40 10 12 42 24 60 30 x 5 0.05
50-80 12 14 49 28 70 40 x 6 0.10
100-200 16 18 63 34 90 50 x 8 0.21
250-350 20 23 80 45 115 60 x 8 0.32
400-500 24 27 98 58 140 70 x 10 0.57
600-1200 30 33 110 70 165 100 x 10 1.04
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 222(259)
ANCHORAGE No: 372-013
1(1)
14.11.2014
1 APPLICATION
This standard is used for anchorages of carbon and stainless steel piping, using the
sliding supports described in the standards 370-011, 370-012, 370-014, 370-018, 370-
019, 370-020
If the loads are significant, special construction shall be made for them.
Number of lugs:
2 APPLICATION
These guides are used for sliding supports of carbon and stainless steel piping. Type A
used mainly for carbon steel piping. Types B and C are used for stainless steel piping.
3 MATERIAL
Flat bar S235JR, EN 10025-2
4 SURFACE TREATMENT
Sand blasting Sa 2 1/2 and immediate priming which allows one year storage under site
conditions, top coat of epoxy paint, total thickness 200 m.
5 DESIGNATION
Name, type, standard No.
Example: Guide for sliding support, A, 372-015
1.1 Material
1.2 Designation
2.1 Material
2.2 Designation
3.1 Material
3.2 Designation
4.1 Material
4.2 Designation
Name, type, d, standard No.
Example: Attachment, D, 16, 372-025
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 233(259)
GUIDING SUPPORTS FOR INSULATED PIPES DN 150…1200 No: 372-030
1(2)
14.11.2014
13 APPLICATION
This guiding support is for insulated carbon and stainless steel piping, when guiding
tolerances or forces require stronger support than the support presented on standard 372-
015. Dimensions of sliding supports as on standards 370-011, 370-012 and 370-014.
Guides 372-015 type A shall be used.
14 MATERIAL
S235JR, EN 10025-2
16 OPERATION TEMPERATURE
t 300 C
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 234(259)
GUIDING SUPPORTS FOR INSULATED PIPES DN 150…1200 No: 372-030
2(2)
14.11.2014
17 SURFACE TREATMENT
Hot dip galvanized.
18 DESIGNATION
Guiding support, DN, type, 372-030
Where DN = Nominal size of the pipe.
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 235(259)
PIPE HANGERS No: 372-031
PLATE ATTACHMENT 1(2)
14.11.2014
19 APPLICATION
This standard is used for uninsulated and insulated carbon and stainless steel piping.
These support parts are to be used with hangers and springs for vertical and horizontal
piping
20 MATERIAL
S235JR, EN 10025-2
21 OPERATION TEMPERATURE
t 300 C
22 SURFACE TREATMENT
Hot dip galvanized.
Bolts and nuts: hot dip galvanized.
23 DESIGNATION
Plate attachment, size No, 372-031
24 DIMENSIONS
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 236(259)
PIPE HANGERS No: 372-031
PLATE ATTACHMENT 2(2)
14.11.2014
25 APPLICATION
This standard is used for carbon and stainless steel piping. To be used with plate
attachment according to standard 372-031.
26 MATERIAL
S235JR, EN 10025-2
27 OPERATION TEMPERATURE
t 300 C
28 SURFACE TREATMENT
Hot dip galvanized.
Bolts and nuts: hot dip galvanized.
29 DESIGNATION
Clevis, size No, 372-032
30 DIMENSIONS
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 238(259)
PIPE HANGERS No: 372-032
CLEVIS 2(2)
14.11.2014
31 APPLICATION
This sliding support is used for uninsulated carbon and stainless steel piping. It can be
free standing or guided (see 372-015). Sliding supports are described on standards 370-
018, 370-019 and 370-020.
32 NOTES
When this sliding support is used as a component of an anchorage the assembly
instructions given on standard 372-013 shall be used and the designation 2 shall be given
in requisition and parts lists.
Guides number and type of guides shall be given separately in parts lists.
33 MATERIAL
Flat bar and steel profiles S235JR, EN 10025-2 or equivalent.
35 OPERATION TEMPERATURE
t = 20 C…70 C
36 SURFACE TREATMENT
37 DESIGNATION
DESIGNATION 1:
DESIGNATION 2:
Pipe Dimensions
DN Do D H h
mm mm mm mm
50 60.3 61 104 73
65 76.1 77 113 73
80 88.9 89 119 74
100 114.3 115 134 74
125 139.7 140 146 76
150 168.3 169 161 76
200 219.1 220 186 76
250 273.0 273 213 76
300 323.9 324 238 76
350 355.6 356 254 76
400 406.4 407 280 76
450 457.0 457 305 76
500 508.0 508 330 76
600 610.0 610 381 76
700 711.0 712 432 76
800 813.0 813 483 76
900 914.0 915 534 76
1000 1016.0 1016 584 76
1200 1220.0 1220 686 76
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 241(259)
2-SIDED GUIDE FOR UNINSULATED PIPING DN 50…DN 1200 No: 372-033
3(3)
38 LOADS ON SUPPORTS
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
39 APPLICATION
This sliding support is used for insulated carbon and stainless steel piping. It can be free
standing or guided (see 372-015). Sliding supports are described on standards 370-011,
370-012 and 370-014.
40 ADDITIONAL REQUIREMENTS
When this sliding support is used as a component of an anchorage the assembly
instructions given on standard 372-013 shall be used and the designation 2 shall be given
in requisition and parts lists.
Guides number and type of guides shall be given separately in parts lists.
Because of thermal expansion the length of the support shoe L shall be checked case by
case.
41 MATERIAL
Flat bar and steel profiles S235JR, EN 10025-2 or equivalent.
43 OPERATION TEMPERATURE
t < 300 C
44 SURFACE TREATMENT
Sliding support: hot dip galvanized.
Bolts and nuts: hot dip galvanized
45 DESIGNATION
DESIGNATION 1:
Sliding support, DN, 372-034
Where DN = Nominal size of the pipe
DESIGNATION 2:
Anchorage, DN, 372-034
Where DN = Nominal size of the pipe
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 243(259)
2-SIDED GUIDE FOR INSULATED PIPING DN 50…DN 1200 No: 372-034
2(3)
14.11.2014
Pipe Dimensions
DN Do D H h
mm mm mm mm
50 60.3 61 164 133
65 76.1 77 173 134
80 88.9 89 179 134
100 114.3 115 226 168
125 139.7 140 238 168
150 168.3 169 253 168
200 219.1 220 280 170
250 273.0 273 307 170
300 323.9 324 382 220
350 355.6 356 398 220
400 406.4 407 424 220
450 457.0 457 449 220
500 508.0 508 474 220
600 610.0 610 555 250
700 711.0 712 606 250
800 813.0 813 657 250
900 914.0 915 748 290
1000 1016.0 1016 798 290
1200 1220.0 1220 900 290
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 244(259)
2-SIDED GUIDE FOR INSULATED PIPING DN 50…DN 1200 No:372-034
3(3)
14.11.2014
46 LOADS ON SUPPORTS
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
47 APPLICATION
This sliding support is used for uninsulated carbon and stainless steel piping. It can be
free standing or guided (see 372-015). Sliding supports are described on standards 370-
018, 370-019 and 370-020.
48 ADDITIONAL REQUIREMENTS
When this sliding support is used as a component of an anchorage the assembly
instructions given on standard 372-013 shall be used and the designation 2 shall be given
in requisition and parts lists.
Guides number and type of guides shall be given separately in parts lists.
49 MATERIAL
Flat bar and steel profiles S235JR, EN 10025-2 or equivalent.
51 OPERATION TEMPERATURE
t = 20 C…70 C
52 SURFACE TREATMENT
Sliding support: hot dip galvanized.
Bolts and nuts: hot dip galvanized
53 DESIGNATION
DESIGNATION 1:
Sliding support, DN, 372-035
Where DN = Nominal size of the pipe
DESIGNATION 2:
Anchorage, DN, 372-035
Where DN = Nominal size of the pipe
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 246(259)
4-SIDED GUIDE FOR UNINSULATED PIPING DN 50…DN 1200 No: 372-035
2(3)
14.11.2014
Pipe Dimensions
DN Do D H h
mm mm mm mm
50 60.3 61 104 73
65 76.1 77 113 73
80 88.9 89 119 74
100 114.3 115 134 74
125 139.7 140 146 76
150 168.3 169 161 76
200 219.1 220 186 76
250 273.0 273 213 76
300 323.9 324 238 76
350 355.6 356 254 76
400 406.4 407 280 76
450 457.0 457 305 76
500 508.0 508 330 76
600 610.0 610 381 76
700 711.0 712 432 76
800 813.0 813 483 76
900 914.0 915 534 76
1000 1016.0 1016 584 76
1200 1220.0 1220 686 76
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 247(259)
4-SIDED GUIDE FOR UNINSULATED PIPING DN 50…DN 1200 No:372-035
3(3)
54 LOADS ON SUPPORTS
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
55 APPLICATION
This sliding support is used for insulated carbon and stainless steel piping. It can be free
standing or guided (see 372-015). Sliding supports are described on standards 370-011,
370-012 and 370-014.
56 ADDITIONAL REQUIREMENTS
When this sliding support is used as a component of an anchorage the assembly
instructions given on standard 372-013 shall be used and the designation 2 shall be given
in requisition and parts lists.
Guides number and type of guides shall be given separately in parts lists.
Because of thermal expansion the length of the support shoe L shall be checked case by
case.
57 MATERIAL
Flat bar and steel profiles S235JR, EN 10025-2 or equivalent.
59 OPERATION TEMPERATURE
t < 300 C
60 SURFACE TREATMENT
Sliding support: hot dip galvanized.
Bolts and nuts: hot dip galvanized
61 DESIGNATION
DESIGNATION 1:
DESIGNATION 2:
Pipe Dimensions
DN Do D H h
mm mm mm mm
50 60.3 61 164 133
65 76.1 77 173 134
80 88.9 89 179 134
100 114.3 115 226 168
125 139.7 140 238 168
150 168.3 169 253 168
200 219.1 220 280 170
250 273.0 273 307 170
300 323.9 324 382 220
350 355.6 356 398 220
400 406.4 407 424 220
450 457.0 457 449 220
500 508.0 508 474 220
600 610.0 610 555 250
700 711.0 712 606 250
800 813.0 813 657 250
900 914.0 915 748 290
1000 1016.0 1016 798 290
1200 1220.0 1220 900 290
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 250(259)
4-SIDED GUIDE FOR INSULATED PIPING DN 50…DN 1200 No:372-036
3(3)
14.11.2014
62 LOADS ON SUPPORTS
The allowable loads for material S235JR are presented in the table below. The loads are in the local co-
ordinate system of the slide support.
The total load acting on the slide support must meet the following requirement.
63 APPLICATION
This anchorage is used for carbon and stainless steel pipe elbows, when the loads are
relatively low. This type is installed near to the pressure side of vibrating pumps or
similar equipment in order to prevent the vibration spreading to the pipelines. When used
for welds shall ensure strongly vibrating pumps tightness of the nuts in the clamps.
64 CLAMPS
According to 370-016 or 370-017
65 MATERIAL
Stative pipe P235GH - Plates S235JR, EN 10025-2
67 OPERATION TEMPERATURE
Maximum temperature 300 C
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 252(259)
ELBOW ANCHORAGE FOR PIPING No: 373-021
2(3)
14.11.2014
68 SURFACE TREATMENT
Clamps, hot dip galvanised. Surface treatment of other construction according to
9HX191450-L0006 “Technical Specification for Surface Treatment and Painting
-Metallic Surfaces”.
69 DESIGNATION
Elbow anchorage, DN- L, 373-021.
Where DN = Nominal size of the pipe to be anchored, L = The length of the support pipe
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 253(259)
ELBOW ANCHORAGE FOR PIPING No: 373-021
3(3)
14.11.2014
70 APPLICATION
This anchorage can be used for anchoring pipes where there is no space for sliding
supports.
The plate welded to the main pipe is made of a piece of pipe and of the same material as
the main pipe.
In case the support is made of carbon steel and pipe of stainless steel the carbon steel to
stainless steel, weld should be carefully painted against corrosion.
71 MATERIAL
Stand pipe P235GH – Plates S235JR, EN 10025-2
73 OPERATION TEMPERATURE
Maximum 300 C
74 SURFACE TREATMENT
Primary support: hot dip galvanized.
75 DESIGNATION
Base anchorage DN, L, standard number
Example: Base anchorage 200, L, 373-024
76 MATERIAL
S235JR, EN 10025-2 or equivalent.
77 CLAMP
According to 370-016
78 SURFACE TREATMENT
Painting according to project document 9HX191450-L0006 “Technical Specification for
Surface Treatment and Painting -Metallic Surfaces”.
79 DESIGNATION
Pipe clamp, welded type DN - L, 373-025
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 258(259)
PIPE CLAMP BOLTED TYPE DN 10…DN 500 No: 373-026
1(1)
14.11.2014
1 MATERIAL
S235JR, EN 10025-2 or equivalent.
2 CLAMP
According to 370-016
3 SURFACE TREATMENT
Painting according to project document 9HX191450-L0006 “Technical Specification for
Surface Treatment and Painting -Metallic Surfaces”
4 DESIGNATION
Pipe clamp, DN - L, 373-026
PIPING STANDARDS 9HX191450-L0008
PRIMARY PIPE SUPPORTS 259(259)
COMBINATIONS OF PIPE HANGERS No: 376-001
1(1)
14.11.2014
5 GENERAL
These instructions describe dimension standards for pipe support components used in
combinations.
6 COMBINATION
7 DESIGNATION
Pipe hanger combination, DN -L, 376-010A
where DN = Nominal size of the pipe
L = Total length of the composite eye-rod components given
on standards 372-008, 372-009