Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SLR-TX – 46
Seat
No.
Set P
P.T.O.
SLR-TX – 46 -2- *SLRTX46*
v) The bending moment at plastic hinge is
a) equal to zero
b) equal to yield moment of the section
c) equal to plastic moment of the section
d) greater than the plastic moment of the section
vi) If the same number of bolts has been used in the joints, then which of the
following patterns will yield highest efficiency ?
a) Chain b) Staggered
c) Diamond d) Staggered diamond
vii) The value of load factor which occurs for margin of safety in plastic design
for gravity load is about
a) 1.15 b) 1.65 c) 1.85 d) 2.25
viii) The most economical section for column is
a) rectangular b) solid round c) tubular d) hexagonal
ix) Web crippling generally occurs at the point where
a) Bending moment is maximum b) Shear force is maximum
c) Concentrated load acts d) Deflection is maximum
x) The maximum permissible slenderness ratio of a member carrying loads
resulting from wind is
a) 180 b) 200 c) 250 d) 350
xi) The rolled steel I section are most commonly used as beam because
these provides
a) Large moment of inertia of less cross sectional area
b) Large moment of resistance as compared to other section
c) greater lateral stability
d) all the above
xii) The thickness of single flat lacing should not be less than
a) 1/30th length between inner rivets b) 1/40th length between inner rivets
c) 1/50th length between inner rivets d) 1/60th length between inner rivets
xiii) Shape factor is the property which depends
a) Only on ultimate stress of material
b) Only on yield stress of material
c) Only on geometry of section
d) Both on yield stress and ultimate stress of material
xiv) The number of seismic zones in which the country has been divided as
a) 3 b) 5 c) 6 d) 7
_____________
Set P
*SLRTX46* -3- SLR-TX – 46
Seat
No.
SECTION – I
Set P
SLR-TX – 46 -4- *SLRTX46*
SECTION – II
9. A column ISHB 300 @ 0.630 kN/m with one cover plate 400 mm � 20 mm on
either side is carrying axial load of 1700 kN. Design gusseted base.
M20 grade of concrete is to be used under the base slab. 9
Set P
*SLRTX56* SLR-TX – 56
Seat
No.
Set P
Set P
*SLRTX56* -3- SLR-TX – 56
Seat
No.
SECTION – I
3. Find the shape factor of a T section with 100 mm × 10 mm cross sectional plates
as flange and 150 mm × 10 mm cross sectional plate as web. 9
4. Design a tension member to carry a factored load of 400 kN with two angles placed
back to back. Length of the member is 2.9 m. Design welded connection. 10
5. Design a continuous strut to carry a service load of 175 kN, the effective length
of the strut is 3.2 m. Design bolted connection. 9
Set P
SLR-TX – 56 -4- *SLRTX56*
SECTION – II
8. Design battening for column consisting of 2 ISLC 300 placed face to face over
total width of 300 mm. Length of column is 4 m with both ends hinged. Take
fy = 250 MPa. 9
9. A column section ISHB 350 @ 661.2 KN/m carries a factored axial compressive
load of 1650 KN and factored bending moment of 90 KNm. Design the base
plate and its connections. Assume concrete pedestal of M 20 grade. 9
___________
Set P
*SLRTC35* SLR-TC – 35
Seat
Set P
No.
T.E. (Civil Engineering) (Part – I) (CGPA) Examination, 2018
Design of Steel Structures
P.T.O.
SLR-TC – 35 -2- *SLRTC35*
vi) The failure mode in which an axially loaded compression member may fail
is by
a) local buckling b) crushing
c) torsional buckling d) all of these
vii) The effective length of a structural steel compression member of length L
effectively held in position and restrained against rotation at one end but
neither held in position nor restrained against rotation at the other end, is
a) L b) 1.2 L c) 0.8 L d) 2 L
viii) The slenderness ratio of lacing flat is limited to
a) 350 b) 145 c) 180 d) 250
ix) The best double angle compression member section is
a) Equal angle on same side of gusset
b) Unequal angles with long legs back to back
c) Unequal angles with short legs back to back
d) Equal angles on opposite side of gusset
x) For same load, unsupported length and end conditions a laced column as
compared to battened column
a) Is stronger b) Is weaker
c) Is equally strong d) Can not be compared
xi) A beam section is classed as low shear case when the factored shear force
is less than
a) 0.4 Vd b) 0.6 Vd c) 0.8 Vd d) Vd
xii) Which of the following is a correct match ?
a) Purlin – ISLC b) Girder – ISHB
c) Joist – ISF d) Castelled girder – ISA
xiii) In case of an axially loaded column machined for full bearing, the fastenings
connecting the column to the base plate in gusseted base are designed for
a) 100 % of column load b) 50 % of column load
c) 25 % of column load d) erection loads only
xiv) The thickness of base plate is determined from the
a) flexural strength of the plate
b) shear strength of plate
c) bearing strength of concrete pedestal
d) punching criteria
____________
Set P
*SLRTC35* -3- SLR-TC – 35
Seat
No.
T.E. (Civil Engineering) (Part – I) (CGPA) Examination, 2018
Design of Steel Structures
Day and Date : Thursday, 3-5-2018 Marks : 56
Time : 10.00 a.m. to 1.00 p.m.
N.B. : 1) Answer any three questions from each Section.
2) Use of IS 800 – 2007 and IS 875 Part 1, Part 2 and Part 3
are allowed.
3) Use of scientific non programmable calculator is allowed.
4) Figures to the right indicate full marks.
5) Assume suitable data if necessary and mention it clearly
before the solution.
6) Draw the appropriate sketches whenever necessary.
SECTION – I
bf
Breadth of the flange (bf) = 250 mm
Thickness of the flange(tf) = 23.6 mm
Depth of the section(d) = 600 mm
Thickness of the web(tw) = 11.8 mm
Set P
SLR-TC – 35 -4- *SLRTC35*
4. Design a tension member to carry a factored load of 340 kN. Use 20 mm
diameter bolts of grade 4.6 for the connection. Length of the member is 2.6 m. 10
5. Design a double angle section back-to-back on each side of gusset plate for a
continuous Principal rafter of a truss to carry factored load of 400 kN. Center
to center length of member between centroids of connection is 2.5 m. Use
Welded connection. 9
Section – II
8. Design a laced steel column 8 m long to carry a factored axial load of 1000 KN.
The column is restrained in position but not restrained at both ends. Provide
a single lacing system with bolted connections. The design should confirm to
specifications of IS : 800 – 2007. Also design a suitable single lacing system. 10
9. A built up steel column comprising of two ISWB 400 RSJ sections with their
webs spaced 325 mm transmits a factored axial load of 3000 KN. The joists
are connected by 10 mm thick battens. Safe bearing capacity of soil at site is
300 KN/m2. Concrete of grade fck = 25 N/mm2 is used for the foundation bed.
Permissible compressive stress in concrete = 4 N/mm2. Design a suitable slab
base foundation for the column and sketch the details of the foundation. 9
–––––––––––––––
Set P
*SLRTJ35* -1-
SLR-TJ – –35
SLR-TJ 35
Seat
No. Set P
N.B. : 1) Q. No. 1 is compulsory and attempt any three questions from each
Section.
2) Use of IS 800-2007 and IS 875 are allowed, but not allowed for MCQ
(Q. No. 1).
3) Use of scientific non programmable calculator is allowed.
4) Figures to the right indicates the full marks.
5) Assume suitable data if necessary and mention it clearly before the
solution.
6) Draw the appropriate sketches whenever necessary.
7) Q. No. 1 is compulsory. It should be solved in first 30 minutes in
Answer Book Page No. 3. Each question carries one mark.
8) Answer MCQ/Objective type questions on Page No. 3 only. Don’t
forget to mention, Q.P. Set (P/Q/R/S) on Top of Page.
P.T.O.
Set P
SLR-TJ – 35 -2- *SLRTJ35*
iv) Proof stress for minimum bolt tension is given by
a) 0.5 fub b) 0.6 fub c) 0.7 fub d) 0.8 fub
v) Which of the following is the mode of failure in a fillet weld material ?
a) Tension b) Shear c) Bearing d) Crushing
vi) The slenderness ratio in a tension member as per IS code where reversal of
stress is due to loads other than wind or seismic should not exceed
a) 350 b) 180 c) 100 d) 60
vii) Which of the following is a correct match ?
a) purlin – ISLC b) girder – ISHB
c) Joist – ISF d) castelled girder – ISA
viii) The deflection of steel beams in buildings other than industrial building is limited
to span divided by
a) 180 b) 250 c) 300 d) 325
ix) As per the IS 800 purlins are designed as a
a) Simply supported beams b) Cantilever beams
c) Continuous beams d) Compression member
x) Sag rods are designed as
a) Compression members b) Tension members
c) Laterally supported beams d) Laterally unsupported beams
xi) A beam section is classed as low shear case when the factored shear force is
less than
a) 0.4 Vd b) 0.6 Vd c) 0.8 Vd d) Vd
xii) In case of an axially loaded column machined for full bearing, the fastenings
connecting the column to the base plate in gusseted base are designed for
a) 100% of column load b) 50% of column load
c) 25% of column load d) Errection loads only
xiii) The self weight of a roof truss (N/mm2) may be obtained by
a) (1+5)5 b) (1/3+5)10 c) (1–5)5 d) (1/3 – 5)10
xiv) For economical spacing of roof truss, if t, p, r are the cost of truss, purlin and roof
coverings respectively, then
a) t = p + r b) t = 2p + r c) t = p + 3r d) t = p + 2r
______________
Set P
*SLRTJ35* -3- SLR-TJ – –35
SLR-TJ 35
Seat
No.
SECTION – I
2. A portal frame ABCD hinged at A and at D and subjected to two point loads W
and W acting at mid point of BC and at B respectively. Take AB = L, BC = 2L and
CD = L. Find the collapse load W and draw the bending moment diagram. 9
4. A double angle discontinues strut is to carry a factored axial compression of 178 KN.
The length of the strut between the centres of intersection is 3.08 m. Design the
member for the following two cases.
a) Angles placed back to back on opposite side of gusset.
b) Angles placed on the same side of gusset. 9
SECTION – II
7. Determine the design panel point loads of fink type roof truss for an industrial
building for the following data :
Overall length of building = 48 m
Overall width of building = 16.5 m
Width (c/c of roof columns) = 16 m
c/c spacing of trusses = 8 m
8. Design battening for column consisting of 2 ISLC 300 placed face to face over
total width of 300 mm. Length of column is 4 m with both ends hinged.
Take fy = 250 MPa. 10
9. A column ISHB 350 @661.2 N/m carries an axial compressive factored load of
1700 KN. Design a suitable welded gusset base. The base rests on M15 grade
concrete pedestal. 9
_____________________
Set P
*SLRVB33* SLR-VB 33
S e a t
N o .
5 A J
P.T.O.
SLR-VB 33 -2- *SLRVB33*
Set P
*SLRVB33* -3- SLR-VB 33
S e a t
N o .
SECTION I
2. A beam of uniform section is built in at the end and simply supported at the
other end. If the plastic moment capacity at the fixed end is Mp and fully plastic
moment of the beam is 2 Mp. Find the value of load at collapse. 9
4. Design a single angle strut carrying a service load of 100 KN. The length of
member is 2.1 m. Also design the connection. 9
SECTION II
7. Design an I section purlin for industrial building supported GI sheets roof Given
Spacing of trusses = 5.0 m
Spacing of purlins = 1.5 m
Inclination of main rafter to horizontal = 30°
Weight of GI sheets = 130 N/m2
Imposed snow load = 1.5 KN/m2
Wind load = 1.0 KN/m2 (suction). 9
8. Design a battened column with two channels back to back of length 10 m to carry
an axial factored load of 1400 KN. The column may be assumed to have restrained
in position but not restrained in direction at both ends. 10
9. A column ISHB 350 @ 710 N/m with two plates 450 mm × 20 mm carrying a
factored load of 3600 KN. The column is supported on concrete pedestal to be
built with M 20 concrete. 9
_____________________
Set P
*SLREP28* SLR-EP – 28
Seat
No.
Set P
T.E. Civil Engineering (Part – I) Examination, 2016
(New CGPA)
DESIGN OF STEEL STRUCTURES
Day and Date : Monday, 28-11-2016 Max. Marks : 70
Time : 10.00 a.m. to 1.00 p.m.
N.B. : 1) Q. No. 1 is compulsory. It should be solved in first 30 minutes
in Answer Book Page No. 3. Each question carries one mark.
2) Answer MCQ/Objective type questions on Page No. 3 only.
Don’t forget to mention, Q.P. Set (P/Q/R/S) on Top of Page.
3) Use of IS 800-2007 and IS 875 are allowed, but not allowed
for MCQ (Q. No. 1).
4) Use of scientific non programmable calculator is allowed.
5) Figures to the right indicates the full marks.
6) Assume suitable data if necessary and mention it clearly
before the solution.
7) Draw the appropriate sketches whenever necessary.
SECTION – I
2. A portal frame ABCD hinged at A and fixed at D and subjected to two point loads
2W and 3W acting at midpoint of BC and at B respectively. Take AB = L, BC = 2L
and CD = L. Also take the plastic moment capacity of AB = Mp, BC = 2Mp and
CD = Mp. Find the collapse load W and draw the bending moment diagram. Also
check the value of the bending moment where plastic hinge is not developed. 10
3. An ISLB 200 is used as a diagonal in a foot bridge truss. Factored axial tensile
load is 500 KN. Both flanges are connected to two gusset plates by 16 bolts of
16 mm diameter symmetrically arranged. i.e. 8 bolts per flange. Thus there are
four bolts on each side of web per flange. Determine the maximum tension it can
carry. fy= 250 MPa. 9
4. Design double angle section back to back on each side of gusset 8 mm thick for
continuous principal rafter of a truss to carry factored load of 250 KN. Centre to
centre length of member between centroids of connection is 2.5 m. 9
SECTION – II
8. Design a built up column comprising two rolled steel I sections to resist factored
axial compressive load of 4000 KN. Length of column is 5 m restrained in direction
at both ends, restrained in position at base but not in position in z-z direction.
Use fy250 MPa.
Also design a suitable single lacing system. 10
9. A column ISHB 350 @ 661.2 N/m carries an axial compressive factored load of
1700 KN. Design a suitable bolted gusset base. The base rests on M15 grade
concrete pedestal. Use 24 mm diameter bolts of grade 4.6 for making the
connection. 9
_____________________
Set P