Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
CAPE PHYSICS IA (A&I) Max. Act. CAPE PHYSICS IA (A&I) Max. Act.
Lab #8 Oscillating magnet in magnetic Mark Mark CAPE PHYSICS IA [M&M] U2 M2 S-5 Max. Act
field Lab #13 Adders Mark Mark
A Plot graph of T vs d 1 A Follows instructions 1
B Calculated gradient correctly 1 B Correctly inserts ICs 4013 & 4001 1
C Identified ΔX correctly 1 C Correctly identifies resistors by code 1
D Identified ΔY correctly 1 D Properly inserts wires in circuit board 1
E Correct sig. figs. given for gradient 1 E Correctly connects circuit to ground 1
F Correct units stated for gradient 1 F Correctly connects circuit to 9V supply 1
G Large triangle used for gradient 1 G Correctly connects ½ adder circuit 1
H Y-intercept determined correctly 1 H Correctly tests ½ adder circuit 1
I Explained whether results support I Correctly connects full adder circuit 1
whether T is α to d 1 J Correctly tests full adder circuit 1
J Calculated T of oscillation of the magnet K Properly disconnects apparatus 1
for separation d = 5mm 1 L Securely stores equipment after use 1
K 2 Reasons why in practice it would not be 1 12
possible to measure this time directly 1
Total 12
CAPE PHYSICS IA [M&M] U2 M2 S-5 Max. Act
Lab #14 T - Flip Flops Mark Mark
CAPE PHYSICS IA P/D Max. Act.
Lab #5 Resistivity Mark Mark
A Follows instructions 1
A States Hypothesis 1
B Correctly inserts ICs 4013 & 4001 1
B Draws fully labeled diagram of circuit 1
C Correctly identifies resistors by code 1
C Adequately describes procedure
D Properly inserts wires in circuit board 1
- How diameter was measured 1
E Correctly connects capacitor 1
- How resistance was found 1
F Correctly connects LEDs 1
D States manipulated variable 1
G Correctly connects circuit to ground 1
E States responding variable 1
H Correctly connects circuit to 9V supply 1
F States non-varied quantities 1
I Performs tests to verify Toggle function 1
G Appropriate graph plotted 1
J Handles apparatus gently and carefully 1
H Special precautions 1
K Properly disconnects apparatus 1
I Stated 1 adjustment to procedure 1
L Securely stores equipment after use 1
J Provided relationship between R & A 1
12
K Hypothesis confirmed / refuted 1
Total 12
CAPE Physics IA P&D Max. Act
Lab #14 Radioactivity Simulation – Leaking Mark Mark
CAPE PHYSICS IA M/M Max. Act.
Bottle
Lab #6 Magnetic Field Patterns Mark Mark
Statement of hypothesis 1
A Follows instructions 1
Appropriate apparatus selected 1
B Ensures circuit is connected properly
Stated how dependent variable measured 1
before power switched on 1
Stated how independent variable measured 1
C Uses magnetic compass correctly 1
Correct sequence of steps recorded 1
D Forms circular copper wire loop 1
Suitable number of observations recorded 1
E Forms solenoid from copper wire 1
Controlled variables identified 1
F Correctly places and moves magnetic
Showed how data is to be used 1
compass around - straight wire 1
Plot appropriate graph (ln graph) 1
- circular wire loop 1
Gradient calculated 1
- solenoid 1
Identified steps taken to improve accuracy
I Handles apparatus gently and carefully 1
with given apparatus 1
J Plots points to identify field at
Justified whether hypothesis
appropriate intervals 1
confirmed/refuted 1
K Taps compass occasionally when stuck 1
Total 12
L Properly disconnects apparatus and
securely stores equipment after use 1
Total 12