Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Page 1 of 5
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320 GC EXCAVATOR KTN
Configuration: 320 GC Excavator KTN00001-UP (MACHINE) POWERED BY C4.4 Engine
Systems Operation
320 GC, 320 and 323 Excavators Tool Control System
Media Number -M0081160-01 Publication Date -01/03/2018 Date Updated -12/03/2018
i07243736
Switches
SMCS - 1435; 7332
Illustration 1 g06263310
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 7/13/2019
320 GC Excavator KTN00001-UP (MACHINE) POWERED BY C4.4 Engine(M008523... Page 2 of 5
Illustration 2 g06235283
Electrical harness
Table 1
Supply Voltage + 4.5V ~ +5.5V
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 7/13/2019
320 GC Excavator KTN00001-UP (MACHINE) POWERED BY C4.4 Engine(M008523... Page 3 of 5
Note: The values in Table 1 are for bench testing only. Values may not represent parameters for
machine systems specifications.
Illustration 3 g06246069
PWM signal vs thumb wheel operation angle (deg)
Joystick thumb wheel for clockwise rotation of the work tool is located on the left joystick. When
joystick thumb wheel (5) is pressed FORWARD, a signal is sent to the solenoid for medium pressure
(clockwise rotation). The work tool will rotate in a clockwise direction. The joystick thumb wheel is
not serviceable. The joystick is serviceable.
Joystick thumb wheel for counterclockwise rotation of the work tool is located on the left joystick.
When the joystick thumb wheel (5) is pressed BACKWARD, a signal is sent to the solenoid for
medium pressure (counterclockwise rotation). The work tool will rotate in a counterclockwise
direction. The joystick thumb wheel is not serviceable. The joystick is serviceable.
Joystick thumb wheel for extension of the attachment control valve is located on the right joystick.
When joystick thumb wheel (6) is pressed FORWARD, a signal is sent to the solenoid for the
attachment control valve. Pilot oil will shift the spool in the attachment control valve. The oil from the
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 7/13/2019
320 GC Excavator KTN00001-UP (MACHINE) POWERED BY C4.4 Engine(M008523... Page 4 of 5
pump will flow to the work tool extend. The joystick thumb wheel is not serviceable. The joystick is
serviceable.
Joystick thumb wheel for retraction of the attachment control valve (6) is located on the right joystick.
When joystick thumb wheel (6) is pressed BACKWARD, a signal is sent to the solenoid for the
attachment control valve. Pilot oil will shift the spool in the attachment control valve. The oil from the
pump will flow to the work tool retract. The joystick thumb wheel is not serviceable. The joystick is
serviceable.
The work tool operates when the switch is depressed. When the switch is pressed, a signal is sent to
the machine ECM. The machine ECM sends a signal to the solenoids to control the attachment
control valves for one-way flow to the work tool. When the switch is released, the machine ECM
discontinues power to the solenoids. The work tool stops operating.
Illustration 4 g06218923
Foot pedal (electric) and electrical harness
Table 2
Supply Voltage + 4.5V ~ +5.5V
Output Signal 500 ± 75 Hz (PWM)
Output Range 5% ~ 95%
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 7/13/2019
320 GC Excavator KTN00001-UP (MACHINE) POWERED BY C4.4 Engine(M008523... Page 5 of 5
Note: The values in Table 2 are for bench testing only. Values may not represent parameters for
machine systems specifications.
Illustration 5 g06218935
Output signal (PWM) vs foot pedal angle (deg)
This pedal detects the operator input, and sends the input to machine ECM as a PWM signal.
Pedal for extension of the attachment control valve is located left of the travel pedals. When the pedal
is pressed FORWARD, a signal is sent to the solenoid for the attachment control valve. Pilot oil will
shift the spool in the attachment control valve. The oil from the pump will flow to the work tool.
Pedal for retraction of the attachment control valve is located left of the travel pedals. When the pedal
is pressed BACKWARD, a signal is sent to the solenoid for the attachment control valve. Pilot oil
will shift the spool in the attachment control valve. The oil from the pump will flow to the work tool.
Copyright 1993 - 2019 Caterpillar Inc. Sat Jul 13 22:42:08 UTC+0700 2019
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 7/13/2019