Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Mission
To provide quality technical education in tune with the challenges.
To offer latest technological developments in the field of
Aeronautical Engineering.
To integrate the intellectual, spirtual, ethical and social development
of the students for becoming dynamic Aeronautical Engineers.
To initiate desires for undertaking entrepreneurship and life long
learning.
Ex No: 1 DESIGN AND DRAFTING OF RIVETED JOINTS
Date:
AIM:
To design the riveted joints by over lapping and butt joint method using AUTOCAD
2004 software.
TYPE OF JOINTS:
Riveted joints may be classified according to
• Purpose for which it is used for Ex., structure (or) leak proof joints.
• The number of rows of rivet such as single, double, triple (or) quadratic riveted
joints.
LAP JOINT:
The places to be connected over lap each other and rivets pass through drilled holes.
when the plates are tension (or) compression Fig(1),a couple acts about the rivets, being not in
same plate tending to bend joints. To avoid the plates are sometimes bend before riveting to
approximately infinite force shown, to reduce the bending action.
BUTT JOINT:
The plates are kept in alignment and a butt strap (or) cover plate {either single or double}
is plate over the joint and rivets are inserted through the hole in plates aligned over another. The
connection of two main plates is through but straps. The butt joint with single butt strap has some
fracture that of lap joints. Thus therefore should never be used for high loading and pressure feed
areas which are fuselage, wings attachment are scalped that they be efficiently caused.
Those joints are called single riveted, a double riveted etc, depending upon the no of rows of
rivet on each main plate.
TEMINOLOGY:
1. Gauge line:
The line through the centers of rivet and parallel to edge of plate is termed as a row (or)
gauge line.
2. Pitch:
The distance between centers of adjacent rivet measured on gauge line called the pitch “p”.
4. Diagonal pitch:
The distance between the adjacent rivet centers to adjacent gauge line for zigzag riveting.
All the rivets gets sheaved for lap joint and butt joint with single strap the rivets are in
single shear while in butt joints with double strap, the rivets are in double shear shown figure..
A plate get torn along any section in this case all the rivets except these between the edge of
torn plate and tearing section gets sheared. It is only by this combination that the plate small tear
along a section.
5. Shearing of rivets:
Shearing area of rivet in single {lap joint} = d2
Shearing area of rivet in double shear is not exactly double of that in single but little less. As
per in Indian boiler regulations, it is taken as 1.875times the area in single shear. According
shear as of a rivet in double shear =d21.875
6. Crushing of rivets:
Crushing area of a single rivet =d×t and if „n‟ be the no of rivets under crushing the crushing
resistance is equal to σcr.
P
P
Consider the pitch length of joints draw two parallel lines AB and CD at a distance „p‟ apart
and passing through centers of adjacent rivets of a row.
The rivets in shear are equal to the no of rivets contained between these lines for Eg in fig.
First row and second row has one rivet each in shear.Thus the rivets in shear are two.
Description of joint like lap joint,butt joint with single strap (or) double strap determines the
shearing area per rivets (ie) d2 (or) 1.875d2
Total shearing area of rivets equal the produce the value determined at above.
Thus for d<2.54t crushing failure will not occurs in lap joints and butt joints with single strap
and for d<1.075t rivets will never failure in crushing in any type of joints.
Knowing „t‟ and „d‟ the pitch of rivet in found by equating the shearing resistance of rivet found
be tearing resistance of one pitch length of joints.
Plates
Rivets
=p-(d/p)
For
Lap joints,
• single 45% to 65%
Command used:
Line
Circle
Offset
Hatch
Arc
PLATE TEARING IN FRONT OF THE RIVET:
P P
TEARING OF RIVETS:
P P
SINGLE SHEAR FOR LAP JOINT:
P
P
P
P
P
DRAFTING:
Date:
Date:
RESULT:
Thus for riveted joints with over lapping and butt joints method has been
designed with the consideration of failure which are being occurred in riveted
joints and also has been drafted by using AUTOCAD 2004 software.
Ex No: 2 DESIGN AND DRAFTING OF WELDED JOINTS.
Date:
AIM:
To design the welded joints which are used for assembling aircraft structures by using
AUTOCAD 2004 software.
WELDED JOINTS:
Welded joints are threaded, cottered, or knuckle joints are permanent in nature and the
component together cannot be separated or dissembled without breaking the weld metal to the
connected part. A machine part or structure whose component parts are joint by welding is called
weldment.
Welded joints are light in weight, when compared to riveted joints due to elimination of
corer plates or straps, gassed plates, chip angle
BUTT WELD:
A butt weld is obtained by putting together the edges of two pieces having practically the
same cross section and heating until fused together.
LAP WELD:
The plates to be joined are made to overlap each other for a certain distance and the right
angle recess so forward along the width of the plates are filled with weld metal.
EDGE WELD:
This type of joint is not recommended for plates thicker than 6mm.
TEE WELD:
The plates to be joined to form a tee may be beveled at on one side, on both sides or is
may not be beveled at all. Although, these joints should preferably be welded on both sides, this
is not always possible as the two sides may not be accessible.
TEE WELD:
CORNER WELD:
If a fillet weld is placed on the inside of a corner joint, it is usually a light weld. The total
throat „t‟ of the weld is of the order of 1.35 times the thickness of the plate.
DESIGN CONSIDERATIONS OF WELDED JOINT:
Strength of welds in plane loading:
Welded joints subjected to tension may be divided into three classes with respect to the
internal
Stress set up at the external load.
IN CLASS 1, the weld is subjected only to longitudinal shear.
IN CLASS 2, the weld is in transverse shear in tension.
IN CLASS 3, the weld is in pure tension.
Command used:
Line
Circle
Offset
Hatch
Arc
DRAFTING:
Date:
RESULT:
Thus for the welded joints are designed according to its different loading conditions and
has been drafted by using AUTOCAD 2004 software.
Ex No: 3 DESIGN AND DRAFTING CONTROL COMPONENT
CAM
Date:
AIM:
To design and draft control component cam by using AUTOCAD 2004 software.
DESCRIPTION:
CAM MECHANISMS:
The transformation of one of the simple motions, such as rotation, into any other
motions is often conveniently accomplished by means of a cam mechanism. A cam mechanism
usually consists of two moving elements, the cam and the follower, mounted on fixed frame.cam
devices are versatile, and almost any arbitrarily-specified motion can be obtained. In some
instances, they offer the simplest and most compact way to transform motions.
A cam may be defined as a machine element having a cured outline or a groove, which
by its oscillation or rotation motion, gives a predetermined specified motion to another element
called the follower. The cam has a very important function in the operation of many classes of
machines, especially those of the automatic type, such as printing presses, textile machinery,
gear-cutting machines, and screw machines. In any class of machinery in which automatic
control and accurate timing are paramount, the cam is an indispensable part of variety. Some of
the most common forms will be considered in this chapter.
CAM- NOMENCLATURE:
TRACE POINT:
A theoretical point on the follower, corresponding to the point of a fictitious
knife-edge follower. It is used to generate the pitch curve. In this case of a roller follower, the
trace point is at the center of the roller.
PITCH CURVE:
The path generated by the trace point at the follower is rotated about a stationary
cam.
WORKING CURVE:
The working surface of a cam in contact with the follower. For the knife-edge
follower of the plate cam, the pitch curve and the working curves coincide. In a close or grooved
cam there is an inner profile and an outer working curve.
PITCH CIRCLE;
A circle from the cam center through the pitch point. The pitch circle radius is
used to calculate a cam of minimum size for a given pressure angle.
BASE CIRCLE:
The smallest circle from the cam center through the cam profile curve.
STROKE :
The greatest distance or angle through which the follower moves or rotates.
FOLLOWER DISPLACEMENT:
The position of the follower from a specific zero or rest position (usually it‟s the
position when the follower contact with the base circle of the cam) in relation to time or the
rotary angle of the cam.
PRESSURE ANGLE:
The angle at any point between the normal to the pitch curve and the
instantaneous direction of the follower motion. This angle is important in cam design because it
represents the steepness of the profile.
Command used:
Circle
Offset
Hatch
Arc
DRAFTING:
Date:
RESULT:
Thus the control components of cam has been drafted by using AUTOCAD 2004
software.
Ex No: 4 DESIGN AND DRAFTING CONTROL COMPONENTS
BELLCRANK
Date:
AIM:
To design and draft the control components of ell crank by using AUTOCAD 2004
software.
A bell crank is shown fig 1. Bell crank are the most component in mechanical linkage.
Bell cranks are simple devices that are used to change the direction of movement. In fig 1, the
input and output direction of movement differ by 900. Bell crank can also create mechanical
advantage when
L1 L2.
Command used:
Line
Circle
Offset
Hatch
Arc
DRAFTING:
Date:
RESULT:
Thus the control components of bell crank has been drafted by using AUTOCAD 2004
software.
Ex No: 5 DESIGN AND DRAFTING CONTROL COMPONENTS
GEAR
Date:
AIM:
To design and draft the control components of gear by using AUTOCAD 2004 software.
DESCRIPTOPN:
A gear or more correctly a "gear wheel" is a rotating machine part having cut teeth, or
cogs, which mesh with another toothed part in order to transmit torque. Two or more gears
working in tandem are called a transmission and can produce a mechanical advantage through a
gear ratio and thus may be considered a simple machine. Geared devices can change the speed,
magnitude, and direction of a power source. The most common situation is for a gear to mesh
with another gear, however a gear can also mesh a non-rotating toothed part, called a rack,
thereby producing translation instead of rotation.
When two gears of unequal number of teeth are combined a mechanical advantage is
produced, with both the rotational speeds and the torques of the two gears differing in a simple
relationship.
TYPES OF GEAR:
HELICAL GEAR:
Helical gears offer a refinement over spur gears. The leading edges of the teeth are not
parallel to the axis of rotation, but are set at an angle. Since the gear is curved, this angling
causes the tooth shape to be a segment of a helix. Helical gears can be meshed in a parallel or
crossed orientations. The former refers to when the shafts are parallel to each other; this is the
most common orientation. In the latter, the shafts are non-parallel, and in this configuration are
sometimes known as "skew gears".
DOUBLE HELICAL:
Double helical gears, or herringbone gear, overcome the problem of axial thrust presented
by "single" helical gears by having two sets of teeth that are set in a V shape. Each gear in a
double helical gear can be thought of as two standard mirror image helical gears stacked. This
cancels out the thrust since each half of the gear thrusts in the opposite direction. Double helical
gears are more difficult to manufacture due to their more complicated shape.
For each possible direction of rotation, there are two possible arrangements of two
oppositely-oriented helical gears or gear faces. In one possible orientation, the helical gear faces
are oriented so that the axial force generated by each is in the axial direction away from the
center of the gear; this arrangement is unstable. In the second possible orientation, which is
stable, the helical gear faces are oriented so that each axial force is toward the mid-line of the
gear. In both arrangements, when the gears are aligned correctly, the total (or net) axial force on
each gear is zero. If the gears become misaligned in the axial direction, the unstable arrangement
generates a net force for disassembly of the gear train, while the stable arrangement generates a
net corrective force. If the direction of rotation is reversed, the direction of the axial thrusts is
reversed, a stable configuration becomes unstable, and vice versa.
Stable double helical gears can be directly interchanged with spur gears without any need
for different bearings.
BEVEL GEAR:
A bevel gear is shaped like a right circular cone with most of its tip cut off. When two
bevel gears mesh their imaginary vertices must occupy the same point. Their shaft axes also
intersect at this point, forming an arbitrary non-straight angle between the shafts. The angle
between the shafts can be anything except zero or 180 degrees. Bevel gears with equal numbers
of teeth and shaft axes at 90 degrees are called miter gears.
The teeth of a bevel gear may be straight-cut as with spur gears, or they may be cut in a
variety of other shapes. Spiral bevel gear teeth are curved along the tooth's length and set at an
angle, analogously to the way helical gear teeth are set at an angle compared to spur gear teeth.
Zero bevel gears have teeth which are curved along their length, but not angled. Spiral bevel
gears have the same advantages and disadvantages relative to their straight-cut cousins as helical
gears do to spur gears. Straight bevel gears are generally used only at speeds below 5 m/s
(1000 ft/min), or, for small gears, 1000 rpm.
HYPOID GEAR:
Hypoid gears resemble spiral bevel gears except the shaft axes do not intersect. The pitch
surfaces appear conical but, to compensate for the offset shaft, are in fact hyperboloids of
revolution. Hypoid gears are almost always designed to operate with shafts at 90 degrees.
Depending on which side the shaft is offset to, relative to the angling of the teeth, contact
between hypoid gear teeth may be even smoother and more gradual than with spiral bevel gear
teeth. Also, the pinion can be designed with fewer teeth than a spiral bevel pinion, with the result
that gear ratios of 60:1 and higher are feasible using a single set of hypoid gear.
This style of gear is most commonly found driving mechanical differentials; which are
normally straight cut bevel gears; in motor vehicle axles.
Command used:
Line
Circle
Offset
Hatch
Arc
DRAFTING:
Date:
RESULT:
Thus the control component of gear has been drafted by using AUTOCAD 2004 software.
Ex No: 6 DESIGN AND DRAFTING CONTROL COMPONENTS
PUSH PULL ROD
Date:
AIM:
To design and draft the control component of push pull rod by using AUTOCAD 2004
software.
DESCRIPTION:
The push pull rod is used between bell crank and from bell crank to torque arms
(“horns”) to transmit the force and motion from one to the other. A push-pull rod connected to a
bell crank is shown in fig. push pull rods are also called control rods because they are often in
control systems.
APPLICATION:
AIRCRAFT:
The push-pull rod is used to move the control surface of the Aircraft.
IC ENGINE:
The push pull rod is used to operate the inlet and outlet port of the IC engines.
Command used:
Line
Circle
Offset
Hatch
Arc
DRAFTING:
Date:
RESULT:
Thus the control components of push pull rod has been drafted by using AUTOCAD
2004 software.
Ex No: 7 THREE VIEW DIAGRAM OF TYPICAL AIRCRAFT
Date:
AIM:
To design and draft the three view diagram of typical aircraft by using AUTOCAD 2004.
CATEGORIES OF AIRCRAFT:
Unpowered Powered
Hybrid moored balloon Hybrid airship
Powered
Hovercraft
Flying
Bedstead
Avrocar
WHAT IS AN AIRCRAFT:
Aircraft are vehicles which are able to fly by being supported by the air, or in general, the
atmosphere of a planet. An aircraft counters the force of gravity by using either static lift or by
using the dynamic lift of an airfoil, or in a few cases the downward thrust from jet engines.
MILITARY AIRCRAFT:
A military aircraft is any fixed-wing or rotary-wing aircraft that is operated by a legal or
insurrectionary armed service of any type. Military aircraft can be either combat or non-combat:
Combat aircraft are aircraft designed to destroy enemy equipment using its own
armament.
Non-Combat aircraft are aircraft not designed for combat as their primary function, but
may carry weapons for self-defense. Mainly operating in support roles.
Combat aircraft divide broadly into fighters and bombers, with several in-between types such as
fighter-bombers and ground-attack aircraft (including attack helicopters).
Other supporting roles are carried out by specialist patrol, search and rescue, reconnaissance,
observation, transport, training and Tanker aircraft among others.
CIVIL:
Civil aircraft divide into commercial and general types, however there are some overlaps.
COMMERCIAL:
Commercial aircraft include types designed for scheduled and charter airline flights,
carrying both passengers and cargo. The larger passenger-carrying types are often referred to as
airliners, the largest of which are wide-body aircraft. Some of the smaller types are also used in
general aviation, and some of the larger types are used as VIP aircraft.
GENERAL AVIATION:
General aviation is a catch-all covering other kinds of private and commercial use, and
involving a wide range of aircraft types such as business jets (bizjets), trainers, homebuilt,
aerobatic types, racers, gliders, war birds, firefighters, medical transports, and cargo transports,
to name a few. The vast majority of aircraft today are general aviation types.
Within general aviation, there is a further distinction between private aviation (where the
pilot is not paid for time or expenses) and commercial aviation (where the pilot is paid by a client
or employer). The aircraft used in private aviation are usually light passenger, business, or
recreational types, and are usually owned or rented by the pilot. The same types may also be
used for a wide range of commercial tasks, such as flight training, pipeline surveying, passenger
and freight transport, policing, crop dusting, and medical evacuations. However the larger, more
complex aircraft are more likely to be found in the commercial sector.
Command used:
Line
Circle
Offset
Hatch
Arc
DRAFTING:
Date:
TOP VIEW
FRONT VIEW
SIDE VIEW
RESULT:
Thus the three view diagram of a typical aircraft has been drafted by using AUTOCAD
2004 software
Ex No:8 LAYOUT OF TYPICAL WING STRUCTURE
Date:
AIM:
To draft and study the wing structural layout of a specified aircraft by using AUTOCAD
2004 software.
WING:
The primary lifting surface of an aircraft is the wing. Wing are attached to airplanes in a
location vertically and longitudinally
WING SPAR:
It is sometimes called a wing beam, is a principal span wise member of a wing structure
WING RIB:
It is sometimes called a plain rib, is a chord wise member of the wing structure used to
give the wing section is shape and also to transmit the air loads from the covering the spar.
For wooden wing construction, the wing spars must be made of a/c quality solid wood
and plywood. Wood spars may be solid or may be build up
The basic structure of a modern transport wing is shown. Transport wing consists of two
or more main spars with intermediate spars assist the main spars in carrying operational loads.
The front and rear spars provide main supporting structure for fittings attaching fuselage engine,
pylons, main landing gear and flight surface to wing.
Located between the ribs, depending upon their design may be used for purposes such as
fuel bulkheads and support of control surfaces as well as providing the aerofoil shape of the
wing.
Command used:
Line
Circle
Offset
Hatch
Arc
DRAFTING:
RESULT:
Thus the layout of typical wing structure has been drafted by using AUTOCAD 2004
software.
Ex No:9 LAYOUT OF TYPICAL FUSELAGE STRUCTURE
Date:
AIM:
To draft and study the fuselage structure layout of specialized aircraft by using
AUTOCAD 2004 software.
FUSELAGE:
The fuselage is the body of aircraft to which the wings and the tail unit are attached. It
provides space for the crew, passenger, cargo ,control and other items, depending upon it size
and design of the aircraft. The aircraft structure is designed to provide maximum strength and
minimum weight.
In general, fuselage are classified into three types depending upon the method, to which
the stress are transmitted to the structure. The three types according to this classified are truss,
semimonocoque, monocoque.
CONSTRUCTION OF FUSELAGE:
The fuselage are designed with a variety of structural components. The great majority of
fuselage are all metal and semi monocoque in construction. This statement applies to small
medium and large aircraft.
The interior structure to which the skim or plating is attached consists of longerons,
frames, bulkheads, stringer, gussets, and possible internal coastal members, riveted bound or
jointed together form a rigid structure that shapes of fuselage. The skim or plating is riveted or
bonded to the structure to form the complete unit. Fuselage for aircraft are designed with many
similarities. The forward section of the fuselage usually contain the cockpit and passenger cabin.
The shape of this section depends upon the passenger capacity and the performance specification
for the aircraft. The real section of the tail cone is usually circular or rectangular in cross –
section and taper towards the tail.
BULKHEADS:
Heavy frames reinforced by beams attached to webs are usually called bulkheads.
STRINGERS;
These are longitudinal members spaced around the fuselage circumference the extend the
full length of fuselage. The stringers attached to the out board edge of frame and the in board
face of skin.
FLOOR BEAMS:
It provides the support for the cabin floor attack to the frame and skin horizontally across
the fuselage.
KEEL BEAMS:
It is a major longitudinal fuselage component in the wing center section and wheel well
area. It extends along the fuselage center line through the wheel well and under the wing center
section. The transport fuselage contains one or more mid section assemblies. These mid section
assemblies one basically circular in shape with a constant cross size. The mid section of the
structure contains landing gear attached points.
The off section changes the cross sectional shape of the fuselage into the size and shape
necessary to join with fuselage at the body or tail cone. The center body or tail cone is in the
point of attachment for the flight control surface and depending on the aircraft design. The
fuselage sections are joined to complete the basic assembly of the fuselage may also in corporate
an engine installation area.
Command used:
Line
Circle
Offset
Hatch
Arc
DRAFTING:
Data:
FUSELAGE SHELL
LONGERONS
RESULT:
Thus the layout of the typical fuselage structure has been drafted by using AUTOCAD
2004 software.
Ex No: 10 LAYOUT OF CONTROL SYSTEM
Date:
AIM:
To draft and study the control system layout of specialized aircraft by using AUTOCAD
2004 software.
Spoilers assist the ailerons in providing roll airfoil and operate as speed brakes. The variable
pitch horizontal stabilized assist the elevator is providing pitch control high lift for takeoff and
landing is provided by trailing edge flaps and leading edge slats.
Displacement of either nor of rudder pedals send a signal to the three rudder hydraulic
actuators. The position of the rudder is shown on the EICA‟s {Engine Indicating and new
alerting system } status display
Rudder trim is available by rotating the rudder trim control to the desired direction. The
control provides signals to the electric motor that reposition the rudder neutral point. The rudder
trim indicator show the unit of rudder trim that are signaled.
The control systems from the rudder pedals and trim control to the rudder actuator are
modified by a rudder ratio changer. As airspeed increases the ratio reduces the rudder deflection
that results from the rudders input
The ratio changer receives air data computers airspeed input and provides control signals to an
actuator powered by the left hydraulic system. The actuator modifies the pilots control input
RUDDER CONROL SYSTEM – YAW CONTROL:
YAW
DAMPER
M
R C
L
AILERON CONROL SYSTEM –ROLL CONTROL:
TRIM SWITCHES
LEFT RIGHT
C
ELEVATER CONTROL SYSTEM PITCH CONTROL:
The pitch control surfaces consists of two hydraulically powered elevators and a
hydraulically powered elevators and a hydraulically powered stabilizer to improve speed stability
Moving either control column sends a signal to the hydraulic actuators on the elevators.
There are three actuators for each elevator. If one control column should i am applying sufficient
forward (or) after force to other causes two columns to disconnect pitch column is then available
using the free control system.
Elevator positions are shown on the EICA‟s status display. Separate pointers indicates the
left and right elevator deflection two elevator, “feet system” provide artificial feet forces to the
pilot‟s control columns
The aileron is located on each wing, rotating either control wheel sends a signed to the
aileron hydraulically actuators.
Two actuators are used for each aileron. It positioned are shown on the switches operate an
electric motors that provides systems to reposition the aileron‟s hydraulic system is necessary to
accurately set the aileron trim an aileron trim indicator is located on both control columns and
indicates in unit of trim.
Command used:
Line
Circle
Offset
Hatch
Arc
ELEVATOR CONTROL SYSTEM – PITCH CONTROL:
COLOUMN
DISCONNECT
LEFT RIGHT
HYDRAULI C ELEVATOR ELEVATOR
FEED FEED HYDRAULIC
PROCESS PROCESS
DRAFTING:
Date:
CONTROL WHEEL
BALANCING CABLE
CHAIN &
SPROCKET(ELEVATOR)
PUSH ROD
RESULT:
Thus the control system layout of specialized aircraft was drafted and studied by using
AUTOCAD 2004 software.
CONTENT BEYOND SYLLABUS
Ex No: 11 DESIGN OF 2D MACHINE COMPONENTS
Date:
AIM:
To draft and study the control system layout of specialized aircraft by using AUTOCAD
2004 software.
PROCEDURE:
2. Change the units to millimeters from inches and also precision to 0 by clicking format ->
units ->ok.
3. To set the paper size type zoom -> enter and type a -> enter in Command bar.
7 .From the modify tool bar, use the array command to draw the 6holes with 12dia from
centre of circles
10. Again draw the concentric of radius 100 from centre of circle
11. From the modify toolbar, use the offset command to draw the 12 & 23 distance circle.
12. Draw 2 circles. With radius 23 & 12 on the 100R circle where the 300 line co-inside.
13. From modify toolbar, mirror these circle to represent another side.
14. And offset vertical line from centre of circle with a distance both side of vertical line.
15. From modify toolbar, use the fillet command to represent fillet of radius 10 &9 to the
offset line.
AIM:
To draft and study the control system layout of specialized aircraft by using AUTOCAD
2004 software.
PROCEDURE:
2. Change the units to millimeters from inches and also precision to 0 by clicking format -> units ->
ok.
3. To set the paper size type zoom -> enter and type a -> enter in command bar
4. Draw 2 lines as the axes and draw concentric circles of specified diameter.
5. Draw a ray of 300 angle to the +ve Y axis as shown in the figure and a ray of angle 600 to the –
ve Y axis as shown in the figure.
6. Draw concentric circles from the point where the circle meets the positive Y axis as show.
8. Continue with the design until the AutoCAD drawing his complete.
AIM:
To draft and study the control system layout of specialized aircraft by using AUTOCAD
2004 software.
PROCEDURE:
2. Change the units to millimeters from inches and also precision to 0 by clicking format -> units
-> ok.
3. To set the paper size type zoom -> enter and type a -> enter in command bar
6. Draw the circle with 14dia on 62dia of circle and offset of the vertical line with distance 4 to
both sides of the vertical line
8. Use the array command from modify tool bar to represent the 6 holes with 14 dia of centre of
the circles
10. And draw the 2 circles with 14 radius and 12 dia at coincide of the offset axes
11. From the modify tool bar select the fillet command to represent the 12R fillet