Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
According to Darcy’s Law, the flow rate through a porous media is inversely
proportional to_________.
152 c ID
a- head loss b- cross-sectional area
c- length of the flow path d- none of these
In WCB system, a line is said to be free from local attraction if the difference between
153 a SEE
FB and BB is__________.
a- 180o b- 0o c- 90o d- 120o
Diesel engine is the_____________.
154 a- External combustion engine b- Internal combustion engine b FMP
c-Semi internal combustion engine d- None of the above
The graph between rainfall intensity and time is called_______________.
155 a- hyetograph b- hydrograph a ID
c- mass curve of rainfall d- both (a-& (b-
294- In National Standard for Drinking Water Quality Turbidity should be__________.
156* c SEE
a-< 9 NTU b- =5 NTU c-<5 NTU d- 5.5 NTU
In M.B. plough, the function of gunnel is to____________.
157 a FMP
a-Take side thrust of soil b-Lift soil c-Turn soil d-Pulverize the soil
Pumps in ascending order of head are_________.
158 a- axial, mixed, radial b- mixed, axial, radial a ID
c- radial, mixed, axial d- mixed, radial, axial
First step in solving numerical problems of Dynamic________
159* a-identification of forces b-selection of formula d SEE
c-both (a & b) d-Free body diagram
If compression ratio is increased______________.
a- Thermal efficiency will be increased
160 b- Volumetric efficiency will be increased d FMP
c-Air standard efficiency will be decreased
d- Air standard efficiency will be increased
In a rectangular channel, the alternate depths are 1.0 m and 2.0 m respectively. The
161* specific energy head in m is________. c ID
a- 3.38 b- 1.33 c- 2.33 d- 3.0
160-The function of secondary liner in double leach ate is__________.
162 a-Drain the leachate b- To collect the leachate c SEE
c- Leak detection d- None of these
The engine, which follows diesel cycle, is the_____________.
163 b FMP
a- Petrol engine b- Diesel engine c- Adiabatic engine d-All above
Gully erosion usually control in__________.
164* a- check dams b- diversions d ID
c- spurs d- both (a & b)
If the waste components are not separated when discarded then mixture of these
165 waste is also knows__________. a SEE
a- Commingled residential b- Putrescible waste c- None d- (a & b)
In M.B. plough, the share is made of___________.
166 a FMP
a-Chilled cast iron b-High carbon steel c-Mild steel d-Both (a& b)
If pipes are connected in parallel_______.
167 a- their discharge is added up b- their head is added up a ID
c- their velocity is added up d- their diameter is added up
161-HDPE is strong resistant to most chemicals and is considered__________.
168* a SEE
a- permeable to water b- impermeable to water c- none of these.
The turbulence in diesel engines ensures to___________.
a- Increase the volumetric efficiency b- Increase the compression ratio
169* c FMP
c- Bring the fuel quickly in contact with the air d- Increase the specific fuel
consumption
Critical Velocity Ratio for use in Kennedy’s theory, is________.
170* d ID
a-<1 b->1 c- =1 d- all of above
Percentage contribution of methane to the greenhouse effect on earth is _______
171* c SEE
a- 36-70% b- 60-70% c- 4-9% d- None of these
Diesel engine follows the principle of______________.
172 a FMP
a- Diesel cycle b- Otto cycle c-Petrol cycle d- Auto cycle
Head sluices are the gate controlled openings, in__________.
173 a- the entire length of the barrage b- the undersluices length of the barrage c ID
c- the regulator the main off taking canal d- none of these
If s = (3t2- m, where t is in secs, calculate the particle velocities when t = 1s. v
174 =______ d SEE
a-0 m/s b-2 m/s c-4 m/s d-6 m/s
A slip share is_______________.
175 a-One piece share b-Of two metal pieces share a FMP
c-Attached with landside d-None of the above
For proportionality, weir type outlets should be set at__________ depth:
176*
a- 0.9 b- 0.8 a ID
*
c- 0.6 d- 0.3
The curvature of earth is not take into consideration is called__________------
177 surveying b SEE
a- Plane surveying b- geodetic surveying c- both (a &b) d- none of above
Clutch noises are usually most noticeable when the engine is___________.
178 d FMP
a. Being started b. Deceleratingc. Stopped d. Accelerating
In an arch dam loads are resisted by__________.
179 a- weight of dam b- arch action c ID
c- both (a- and (b- d- none of them
Resistance to indentation is called_________.
180 c SEE
a- Hardness b- resilience c- strength d- ductility
In 2-stroke cycle engine, one cycle is completed in_________________.
181 a. 2 revolutions of crank shaft b. One revolution of crank shaft c. b FMP
c. 4 revolutions of crank shaft d. 3 evolutions of crank shaft
Aquifer having same hydraulic conductivity in all directions at a point is called______.
182 a- homogeneous b- isotropic b ID
c- anisotropic d- both (a-& (b-
Which are of the following source of polluting the air_______?
183 a- Using an air conditioner b- Using a hair dryer d SEE
c- Watching TV d- All of above
In m.b. plough, the mould board serves the purpose of______________.
184 a-Receiving the furrow slice b-Lifting and turning the soil d FMP
c-Pulverizing the soil d-All above
Time from the centeroid of net rainfall to the peak of hydrograph is called________.
185 a- time of concentration b- lag time d ID
c- basin lag d- both (b-& (c-
To eliminate collimation error the leveling instrument must be placed________.
186 c SEE
a- Near BS b- near FS c- exactly mid-way d- between BS and FS
As compression ratio in an engine goes up, the octane requirements of the
187 b FMP
fuel______.
a. Goes down b. Goes up c. Stay about the same d. not
concerned
Pumps in ascending order of discharge are_______.
188 a- axial, mixed, radial b- mixed, axial, radial c ID
c- radial, mixed, axial d- mixed, radial, axial
The mixture of lime stone and clay is called_________.
189 a SEE
a- Cement b- sand c- concrete d- mortar
In a four stroke diesel engine, the ignition takes place due to_______.
190 d FMP
a. Spark b. High pressure c. High temperature d. Both (b-& (c-
A rectangular channel carries a certain flow for which the alternate depths are found
191 to be 3.0 m and 1.0 m. The critical depth in m for this flow is________. b ID
a- 2.65 b- 1.65c- 0.65 d- 1.33
What are the errors associated with maps___________?
192 c SEE
a-Distance b-Area c-"DADS" d-None
In grassy lands, the best mould board for use, is______________.
193 a FMP
a-Sod or breaker type b-Stubble type c-General purpose type d-Slot type
Typical width of strip-cropping ranges from_______.
194 a- 20 to 50 m b- 30 to 100 m b ID
c- 50 to 100 m d- none of above
Which one of the micro nutrient is found in Bio solids____________.
195 d SEE
a-Sulphur b- Calcium c- Molybdenum d- Both b & c
Cam shaft is driven by__________.
196 a FMP
a-Crank shaft b-Drive wheel c-Piston d-Piston rod
A line joining the tops of liquid in piezometers is called__________.
197 a- energy line b- imaginary line c ID
c- hydraulic grade line d- datum line
Desiccation of clay during construction results in cracks that__________.
198 a- reduce the efficiency b-increase the efficiency a SEE
c- have no effect on liner efficiency d- none of these
In diesel engine, the cylinder is fitted with________________.
199 a FMP
a- Movable piston b-Piston rod c-Crank shaft d- Crank case
The Garret’s diagrams are based on________.
200 a-Lacey’s theory b-Khosla’s theory d ID
c- Bligh’s theory d- Kennedy’s theory
At a junction of tree trunk and limbs_________.
201 c SEE
a- Growth defect b- seasoning defect c- knots d- lumber grades
The rear bottom of land side is called_____________.
202 a FMP
a-Heel b-Wing c-Bearing d-Shin
The tunnel openings provided infront of a canal head regulator at a diversion
headworks_________.
a- Discharge sedimented water into the canal
203 b ID
b- discharge sediment load into the undersluices, from where I ejects out to the
downstream river
c- discharge clear water into the canal d- none of these
Factor which is not affecting deteriorating rocks____________.
204 d SEE
a- Rain b- temperature c- wind d- moisture content
205 Which type of valve arrangements requires the use of rocker arms? c FMP
a- H – head b- T – head c- I – head d- L – head
For proportionality, pipe outlets should be set at__________ depth:
206 a- 0.9 b- 0.8 d ID
c- 0.6 d- 0.3
277-The variation of shear force due to a triangular load on simply supported beam
207 is_________ c SEE
a- uniform b- linear c- parabolic d- cubic
In diesel engine the component placed at the place of spark plug, is________.
208 a-Nozzle b- Intake valve c- Exhaust valve d- Piston rod a FMP
The optimum kor water depth for a kharif crop is 19 cm with an allowed kor water
566 a ID
period of weeks, the outlet discharge factor for this crop will be________________.
a- 955 ha/cumec b- 782 ha/cumec
c- 860 ha/cumec d- none of them
The first staff reading taken in any set up of the instrument is known as__________.
567 a SEE
a-BS b-FS c- both A and B d- none
The part of engine, through which the air or air fuel mixture enters into cylinder, is
568 called___________. a FMP
a-Inlet manifold b- Intake valve c- Inlet valve d- Sleeve
Ideal minimum bed gradient in an open drain is to have sufficient velocity
at_________.
569 a ID
a- low flows b- mean flow
c- high flow d- all of above
Which senses the changes in body environment __________.
570 b SEE
a- Heart b- Brain c- Skin d- Eyes
A plough which is partly carried by the tractor when in and out of work is
called________.
571 b FMP
a-Mounted type plough b-Semi-mounted type plough
c-Trailed type plough d-Sliding plough
For laminar flow in a medium sand aquifer, the RN is___________________.
572 a-<2000 b-<1 b ID
c- 1 to 10 d-<50
The main principle of surveying is to work from__________.
573 b SEE
a-The center to boundary b- the whole to part c-The part to whole d- none of above
Changing position of an object against an opposing force is called__________.
574 d FMP
a- Power b- Torque c- Energy d- Work
Formation of a layer or film of water before it starts flowing to generate runoff, is
called____________________________.
575 c ID
a- depression storage b- percolation
c- detention storage d- none of these
Management data for solid waste includes__________.
576 d SEE
a- Altitude b- Weather condition c-Living habits d- All of above
The size of cam shaft gear is______________.
577 a-Double of the crank shaft gear b- Half of the crank shaft gear a FMP
c-Equal to the crank shaft gear d- The same as timing gear
Maximum evapotrainspiration is defined for___________________-.
578 a- Alfalfa b- Grass c ID
c- None of a- and b- d- Both of a- and b-
211-Which scattering is responsible bluish color of sky__________.
579 b SEE
a-Mie Scattering b-Rayleigh scattering c-Non selective Scattering d-None
The useful life of seed cum fertilizer drill is_______________.
580 a FMP
a-8 years b-10 years c-12 years d-15 years
The Manning’s n for a straight concrete sewer is about________________.
581 a- 0.025 b- 0.014 b ID
c- 0.30 d- 0.14
The relative closing error should not exceed__________.
582 a SEE
a- 1/600 b- 1/400 c- 1/1000 d- 1/500
When air is heated, it______________.
583 c FMP
a- Contracts and becomes heavier b- Expands and becomes heavier
c- Expands and becomes lighter d- Contracts and becomes lighter
The mercury does not wet the glass. This is due to the property of liquid
called______.
584 c ID
a- cohesion b- adhesion
c- surface tension d- viscosity
Rubber is a type of __________.
585 a- Biodegradable waste b- Integrated waste c SEE
c- Non biodegradable waste d- All of above
In I.C. engine, the tappet is also called_____________.
586 c FMP
a-Lifter b- Cam shaft c- Crank case d- Timing valve
The crop among the following, which is expected to have the maximum duty_______.
587 a- Wheat b- Rice a ID
c- Sugarcane d- Cotton
__________is produced due to anaerobic digestion of organic waste
588 a SEE
a-Biogas b- Carbon dioxide c- Carbon monoxide d-all of above
For sowing sorghum, the most suitable seed metering device is_____________.
589 a-Fluted roller type b-Inclined cell plate type a FMP
c-Foam pad type d-Horizontal cell plate type
For carrying the same discharge, a lined canal can have a bed canal slope______.
590 a- steeper b- milder b ID
c- same d- none of above
197-What are the things a map tells you__________.
591 d SEE
a-Geographic position b-Attributes c-Spatial relationships d-All of Above
Due to heat of combustion, with increase in temperature the
molecules____________.
592 c FMP
a- Move slower b- Vaporize
c- Move faster d- Stop moving
The formation of a hydraulic jump on a sloping glacis, as compared to that on a
horizontal floor, is always:
593 b ID
a- more definite and more efficient b- more definite and less efficient
c- less definite and more efficient d- less definite and less efficient
BF = 0.83 - 0.028LC, LC is__________.
594 b SEE
a-Leat constant b- lignin content c- least carbon d- none
In I.C. engine, the function of tappet, is to____________.
595 a-Close the valves b- Open the valves a FMP
c- Close or open the valves d- Deliver lubricating oil
If the discharge required for different crops grown in a field is 0.4 cumecs, and the
capacity factor and time factor are 0.8 and 0.5, the design discharge for the
596 distributary will be__________________. c ID
a- 0.80cumecs b- 0.16 cumecs
c- 1 cumecs d- 1.24 cumecs
At the magnetic pole the dip of needle is__________.
597 c SEE
a-180o b- 0 o c- 90 o d- 120 o
In tillage operation the soil broken and loosen for depth____________.
598 a FMP
a-15.2 to 91.4 cm b-100 cm c-75 cm or less d-20 c
For preventing silt deposition in a surface earthen drain. The minimum velocity in m/s
599 b ID
should be__________________.
a- 0.2 b- 0.3
c- 0.5 d- 0.6
The angles between adjacent sides are fixed by plane table is called__________.
600 a- Chain traversing b- compass traversing d SEE
c- theodolite traversing d- plane table traversing
When petrol burns completely, two of the compounds that are formed are_______.
601 a-Carbon dioxide and water b- Water and oxygen a FMP
c- Hydrocarbon and oxygen d- Nitrogen and oxygen
Aquifer having same hydraulic conductivity at different points as well as in different
directions is called_____________.
602 d ID
a- homogeneous b- isotropic
c- anisotropic d- both (a-& (b-
238-Chlorine in NHCL4 called__________.
603 a- free available chlorine b- combine available chlorine b SEE
c- mono chloramines d- none
In I.C. engine, the tappet is made of________.
604 a FMP
a-Hardened steel b- Cast iron c- Mild steel d- Chromium
When an air mass is cooled at constant vapor pressure, it gets condensed at a
temperature, called__________________________.
605 c ID
a- lapse rate b- saturation point
c- dew point d- none of these
Resistance of material to passage of liquid is called__________.
606 c SEE
a- Ease of cleaning b- resilience c- imperviousness d- scratch
Chisel plough is a_____________.
607 a-Primary tillage implements b-Secondary tillage implement a FMP
c-Lister d-Mulch former
For Agricultural point of view, effective rainfall is that portion that contributes
to_____.
608 c ID
a- Ground water recharge b- Dam storage
c- crop rootzone d- River supply
Paints are used as__________.
609 b SEE
a- Coating material b- preservatives c- water resistant d- none
With an increase in temperature the resistance of carbon is___________.
610 a- Unchanged b- Decreased c FMP
c- Increased d- None of the Above
In a wide rectangular channel if the normal depth is increased by 20%, the discharge
would increase by____________________.
611 c ID
a- 20% b- 15.5%
c- 35.5% d- 41.3%
The material which gives well finish is__________.
612 b SEE
a- Metal sheet b- plaster c- mortar d- concrete
The clearance between rocket arm and valve stem, is called_____________.
613 a FMP
a-Tappet clearance b- Valve clearance c- Sleeve d- Buffer space
The falling drops of water become sphere due to _____________________.
614 a- surface tension of water b- compressibility of water a ID
b- viscosity of water d- capillarity of water
615 Carbon produce by factories can travel __________. a SEE
a- 25miles b-<20 miles c->30miles d->20 miles
Components of m.b. plough are bolted to_______________.
616 c FMP
a-Plough bottom b-Landside c-Frog d-Shin
Kor-Watering is the irrigation water supplied to a crop__________________.
a- at the time of its sowing b- Just before harvesting
617 c ID
c- About three weeks after sowing d- About three weeks before
harvesting
Wavelength of Visible Light__________.
618 a SEE
a-400-700nm b-10-1000nm c-0.4-0.7mm d-None of the Above
Almost all bearing used in automotive engines are_____________.
a- Guide bearings b- Friction bearings
619 b FMP
c- Antifriction bearings d- None of the Above
The side slope of lined section usually adopted is selected from the consideration
of_______.
620 a- easy construction b- minimum d ID
c- minimum evaporation loss
d- approximately the same as the angle of repose of the existing natural soil
Spherical co-ordinates are utilized when radial distance and two angles are utilized to
specify the position of particles as in case of __________.
621 c SEE
a-super sonic measurement b-Doppler effect c-Radar measurement d- radius
measurement
In I.C. engine, theoretically, the exhaust valve should be opened at______________.
622 a FMP
a-T.D.C. and B.D.C b- B.D.C c- Upward or downward side d- None of the above
Retrogression is _________________.
a- the backwater effect of weir
b- the rising of the river bed upstream of the weir, during initial years of its
623 construction c ID
c- the lowering of the river bed upstream of the weir, during initial years of its
construction
d- none of them
If a particle is confined to a specific path its motion is said to__________.
624 c SEE
a-Straight line b-CirculaR c- Constrained d-none of these
Horizontal suction is also called________________.
625 b FMP
a-Vertical clearance b-Land suction c-Side clearance d-Throat clearance
‘Duty on capacity’ is also called____________.
626 a- outlet duty b- capacity factor c ID
c- full supply coefficient d- quantity duty
Biogas can be produced by__________.
627 d SEE
a- farmyard manure b- Crop residue c- kitchen waste d- All of above
Petrol and Gasoline is called a hydrocarbon because it consists essentially
of_________.
628 a- Carbon and Hydrogen b- Oxygen and Hydrogen a FMP
c- Carbon and Oxygen d- None of the Above
For preventing weeds and grass growth, the minimum velocity in an earthen drain in
629 b ID
m/s should be_________.
a- 0.3 b- 0.6
c- 0.8 d- 1.0
When reduced level of some fixed points are assumed they are termed____ .
630 a-GTS bench marks b- Permanent bench marks c SEE
c- Arbitrary bench marks d- Temporary bench marks
Generally, in 4-stoke diesel engine, the inlet valve gets opened at___________.
631 a FMP
a-5o before T.D.C b- 5o after B.D.C c- 10o after B.D.C d- 5o after T.D.C
A geologic formation which can only store water but cannot transmit significant
amounts, is called_______-.
632 c ID
a-aquitard b-aquifuge
c-aquiclude d- confined aquifer
171-Under anaerobic conditions sulphate can be reduced to__________.
633 a SEE
a-sulphide b-sulphate c-disulphate d- none of these
Cutting edge of share is 9ocalled_________.
634 a FMP
a-Shin b-Frog c-Gunnel d-Skirt
A constant infiltration rate, which is achieved after the soil is saturated, is
called_____.
635 b ID
a- maximum infiltration rate b- basic infiltration rate
c- lapse rate d- none of these
Hypothtical body capable of absorbing it receives is called__________.
636 a SEE
a- Black body b- emissivity c- absorptive body d- cylindrical body
The three general types of friction bearings are___________.
a-Journal, ball and roller b- Journal, guide and thrust
637 b FMP
c- Journal, shaft and thrust d- None of the Above
For sowing sorghum, the most suitable seed metering device is__________.
1246 a-Fluted roller type b-Inclined cell plate type a FMP
c-Foam pad type d-Horizontal cell plate type
The bed of alluvial channel carrying silted water at high velocity is expected to
be_______.
1247 b ID
a- Rippled b- duned
c- flat d- Wavy
The total solids in water are due to the presence of___________.
1248 a-Suspended and dissolved solids b- suspended and floating solids a SEE
c- colloidal and settle able solids d- Colloidal and bacterial solids
Tempering of metal is done to reduce_____________-.
1249 a- brittleness b- toughness a FMP
c- ductility d- all above
A barrage differs from a weir on account of______________.
1250 a- low set crest b- effective control over river flow d ID
c- series of gates to effect pondage d- all of them
Temporary hardness in water is due to the presence of___________.
1251 a-Chloride hardness b- carbonate hardness c SEE
c-calcium hardness d-Manganese hardness
Too high level of oil in the engine can cause the problem of______________.
1252 a-Excessive fuel consumption b- Blue smoke a FMP
c-Failure to start the engine d- None of the above
An outlet should be proportional in discharge distribution that is___________.
a- drains same discharge irrespective of varying supply in the channel
1253 b- drains more or less discharge corresponding to the varying discharge in the channel b ID
c- drain less discharge
d- drain excess discharge
In distilled water the concentration of hydrogen ion is___________.
1254 a-107 b-10-7 c-2*107 d- 2*10-7 a SEE
The shaft on which disc are mounted is called_______________.
1255 d FMP
a-Gang axle b-Arbor axle c-Main axis d-Both (a & b)
Low river training implies river training for_________________.
1256 a- high floods b- medium floods c ID
c- low floods d- project flood
The weight of hydroxyl ion in a sample of water is found to be 10-9. The pH value of
1257 the water is___________. b SEE
a-10 b- 9 c-( -9) d-1
The process of detaching the grains from ear head or the plants is called__________.
1258 a- Mowing b- Cutting d FMP
c- Winnowing d- Threshing
The soil becomes practically infertile when its pH value is about_____________.
1259 a- 0 b- 7 c ID
c- 11 d- none of them
Water having a pH value 3 is___________.
1260 a SEE
a-Acidic b-Alkaline c-Hard d-Soft
Quality of the fuel is judged by its___________.
1261 a FMP
a-Calorific value b- Power conversion c- Loss to cool the engine d- Consumption
Rate of decrease in atmospheric temperature per unit rise in vertical direction
through troposphere is called________________.
1262 b ID
a- albedo b- lapse rate
c- insulation d- both (a- & (b-
pH value is expressed in ___________.
1263 a-mg b- gm/l c- Degrees d- None of these d SEE
For sowing sorghum, the most suitable seed metering device is__________.
1264 a-Fluted roller type b-Inclined cell plate type a FMP
c-Foam pad type d-Horizontal cell plate type
NPSHA is a function of ____________________.
1265 a- pump b- system b ID
c- both pump and system d- fluid handled
pH value of portable water is___________.
1266 c SEE
a-3 & 5 b-10.5 & 12.6 c-6.5 &8 d- 1.5 & 2
A high speed of thresher mainly causes_______________.
1267 a- Grain damage b- poor threshing a FMP
c- Greater Threshing d- all above
For a given soil,________________________.
a- texture and structure represent same property
1268 b- texture implies presence of particles of different sizes d ID
c- farmer can change the texture using cultivation method
d- texture implies the proportion of sand silt and clay
Nitrate more than 50ppm in water leads to diseases called___________.
1269 b SEE
a-Typhoid b- Mathenoglobenemia c- Gaestroenteritis d-mottled teeth
Quality of the fuel is judged by its______________.
1270 d FMP
a-Volatility b- Ignition quality c- Consumption rate d- Both (a & b)
Mass movement of soil occurs at_____________________.
1271 c ID
a- critical slope b- mild slope
c- steep slope d- none o above
A minimum amount of fluorides is desirable in portable water to prevent__________.
1272 a-Scale formation b- corrosion c SEE
c-dental cavities d-water borne disease
Per unit power requirement is less in case of________________.
1273 a-Primary tillage operations b-Secondary tillage operations d FMP
c-Harrowing and hoeing d-Both (b & c)
A venturimeter is used to measured,______________.
1274 a- velocity of a flowing liquid b- pressure of a flowing fluid c ID
c- discharge of a flowing liquid d- all of these
The alkalinity or acidity of a sample of water is determined by___________.
1275 c SEE
a-MPN index b-E coli index c-pH value d-Electomatric method
Seed Processing is associated to the______________.
1276 a- Farm Processing b- post harvesting processing only a FMP
c-Process industries, only d- all above
The bed form, which is not expected in an alluvial channel with sediment motion,
is__________.
1277 d ID
a- rippled b- meandered
c- duned d- anti duned
The presence of manganese in water causes growth of___________.
1278 b SEE
a-Mosquitoes b- Microorganism c-Flies d- Algae
“Vapor lock” is associated to the___________.
1279 a-Fuel supply system of engine b- Cooling system of engine a FMP
c-Ignition system of engine d- All above
A weir essentially has___________________.
1280 a- no control over high floods b- more afflux d ID
c- shutters in part length only d- all of them
The red brownish color of water is due to the presence of dissolved impurities of____.
1281 d SEE
a-Bi carbonate b-sulphate c- Arsenic d-Iron and manganese
The common cross section of hopper in potato planter is___________.
1282 b FMP
a-Triangular b-Trapezoidal c- Rectangular d-Circular
Modular outlet is that the discharge of which is______________.
a- independent of water level in the distributary
1283 b- independent of water level in the watercourse c ID
c- independent of water levels both in the distributary or watercourse
d- all of the above
Disinfection of water removes___________.
1284 c SEE
a-Hardness b- Turbidity c-Arsenic d- Iron and manganese
The loss of value of machine with laps of time is called_____________.
1285 a- Depreciation b- Salvage value a FMP
c- Lost Value d- all above
Guide banks are provided_________________.
1286 a- in the direction of flow b- at right angle of flow a ID
c- at an angle to the flow d- all of them
The process of killing organism in water is called___________.
1287 d SEE
a-Sedimentation b-Coagulation c- Aeration d-Disinfection
Acceleration characteristics of an engine is effected by______________.
1288 a-Volatility of fuel b- Consumption rate of fuel a FMP
c-Calorific value of fuel d- Ignition quality of fuel
Which of the following crops can withstand the high WT, which normally should be
0.7 to 2.5 m below the level of the cropped land ________________?
1289 d ID
a- wheat b- lucerine
c- cotton d- rice
The process of killing infective bacteria in water is called___________.
1290 a-Sterilization b- Disinfection a SEE
c- Sedimentation d-Coagulation
Distribution of seeds in row by seed drill is affected by___________.
1291 a-Shape of seed tube b-Inclination of seed tube a FMP
c-Height of seed released from tube d-All above
Lines of equal atmospheric pressure are known as_______________.
1292 a- isohyets b- isobars b ID
c- isotherms d- contours
Diseases such as typhoid are caused by bacteria called___________.
1293 a-Non pathogenic bacteria b- Anaerobic bacteria c SEE
c-pathogenic bacteria d-Aerobic bacteria
Drawbar pull from tractor, is taken by means of______________.
1294 a- Drawbar assembly b- P.T.O a FMP
c- Standard d- Pulley
Affinity law-I deals with _____________.
1295 a- pumps head b- impeller speed b ID
c- impeller diameter d- pump design
A sample of water is added to a medium of agar and incubated at 370 for 24 hrs.
Colonies of bacteria are formed. This test is called___________.
1296 a-Total count test b- presumptive test a SEE
c- Confirmative test d-Completed test
In I.C. engine, the tappet is made of ______________.
1297 a FMP
a-Hardened steel b- Cast iron c- Mild steel d- Chromium
Energy will be required to irrigate land_______________.
1298 a- under gravity b- much above the river bed level b ID
c- in delta region d- all of above
Aeration of water is done to remove___________.
1299 a-Suspended impurities b- Floating Impurities d SEE
c- Dissolved salts d-Dissolved gaese
Time of fail of seed through seed tube is affected by______________.
1300 a-Size of seed b-Size of tube d FMP
c-Type of tube d-Both (b & c)
Detachability of soil particle increases with___________________.
1301 a- decreasing median grain size b- increasing median grain size a ID
c- both (a- and (b- d- none of above
Iron and Manganese are removed___________.
1302 a SEE
a-Aeration b-chlorination c-filtration d-lime soda treatment
1303 Smallest Hand Sprayer is_______________. a FMP
a- Hand Atomizer b- Compression Sprayer
c-Knapsack sprayer d- Bucket Sprayer
The Bernoulli’s theorem is applied for _________________.
1304 a- ideal fluid b- incompressible fluid d ID
c- steady flow d- all of these
The process of retaining water in a basin so that the suspended particles may settle as
1305 a result of the action of gravity is termed as___________. d SEE
a-Sterilization b-filtration c-chlorination d-sedimentation
The clearance between rocket arm and valve stem, is called_____________.
1306 a FMP
a-Tappet clearance b- Valve clearance c- Sleeve d- Buffer space
The anti-dunes develop on beds of alluvial streams, when Froude number is______.
1307 a- 0 b- 0.5 d ID
c- 1 d- 1.2
The detention period for water in a sedimentation tank is ___________.
1308 d SEE
a-1-2 hours b-2-4 hours c- 4-8 hours d-8-10 hours
Which of the following furrow openers is used in seed drills______________.
1309 a FMP
a-Single disc type b-Double disc type c-Runner type d-Hoe, type only
A barrage is a hydraulic structure provided on__________________.
1310 a- deep narrow valleys b- wide, shallow valleys d ID
c- rock foundation d- silt and clay and gravel
The chemical name of alum is ___________.
1311 a-Aluminum chloride b-Silver nitrate c SEE
c- aluminum Sulphate d- CoperSulphate
Knapsack sprayers are suitable for____________.
1312 a- Small Trees b- Shrubs d FMP
c- Row crops d- All Above
Semi-modular outlet is that the discharge of which__________.
a- independent of water level in the distributary
1313 b- independent of water level in the watercourse b ID
c- independent of water levels both in the distributary or watercourse
d- all of the above
Very fine suspended and colloidal impurities are removed by a process called______.
1314 c SEE
a-Softening b- Disinfection c- coagulation d- plain sedimentation
In I.C. engine, theoretically, the exhaust valve should be opened at________.
1315 a FMP
a-T.D.C. and B.D.C b- B.D.C c- Upward or downward side d- None of the above
Guide banks are provided to___________________.
1316 a- decrease depth of river flow b- confine river width b ID
c- reduce flood peak d- maintain minimum depth in the river
Alum is used for the process of ___________.
1317 b SEE
a-Filtration b-Co agulation c- Softening d- Disinfection
Hoe type furrow opener works well in____________.
1318 a-Sandy and loamy soils b-Clayey soils c-Soil covered with trashes d-All d FMP
above
While growing crop in high WT areas, open jointed drains, discharging into drains, are
1319 sometimes laid below the cropped land to lower down the WT and to rainfall a ID
effectively. These drains are called__________________.
a- tile drains b- French drains
c- gravity outlets d- surface drains
For thorough mixing up coagulant with the water, Violent agitation is done in ______.
1320 c SEE
a-Sedimentation tank b- Clari-flocculator c-Flash mixer d-Pressure filter
Major component of bronze casting_________________.
1321 a FMP
a- Copper b-Zinc c-Manganese d-Lead
Which of the following instruments is used for measuring relative humidity?
1322 a- barograph b- bimetallic actinography c ID
c- hair hygrograph d- pyranometer
The rate of infiltration in a slow sand filter varies in liters/m2/hour___________.
1323 c SEE
a-3000 to 6000 b-60 to 95 c-100 to 200 d-1000 to 2000
Generally, in 4-stoke diesel engine, the inlet valve gets opened at_____________.
1324 a FMP
a-5o before T.D.C b- 5o after B.D.C c- 10o after B.D.C d- 5o after T.D.C
Affinity law-II deals with ______________.
1325 a- pumps head b- impeller speed c ID
c- impeller diameter d- pump design
The slow sand filter is more efficient in removing bacteria because___________.
1326 a-Effective size of sand grain is small b-Uniformity coefficient of sand is small a SEE
c-water is pretreated d-size of filter is large
Chisel type furrow opener is seed drill is good for _______________.
1327 a FMP
a-Deep seeding b-Shallow seeding c-Medium seeding d-All above
Steady flow in an open channel exists when the
1328 a- flow is uniform b- depth does not change with time b ID
c- channel is frictionless d- channel bed is not curved
The difference between the water level in the filter chamber and the outlet chamber
is known as___________.
1329 a-Negative head b- pressure head b SEE
c- Working head d-Static head
What law of thermodynamics introduced the concept of entropy_____________.
1330 c FMP
a - Zeroth Law b- 1st law (c-2nd Law d-None of the Above
A network of gully is called as_________________.
1331 a- gullied area b- ravine area b ID
c- hilly area d- all above
The removal of bacteria is accomplished in slow sand filter by means of a jelly-like
1332 substance___________. a SEE
a-Zoogleal b-Metabolism c-Schmutdecke d-Pskytobolism
Generally, in 4-stoke diesel engines, the inlet valve gets closed at___________.
1333 a FMP
a-30o before B.D.C b- 5o after B.D.C c- 5o after T.D.C d- 30o after T.D.C
Theoretical velocity of the jet at vena contracta is___________________.
1334 a- (2gh-0.5 b- 2(gh-0.5 a ID
c- 2g(h-0.5 d- 2gh
The rate of infiltration in a rapid sand filter in litres/m2/hours is ___________.
1335 a-6000 to 15000 b-15000 to 18000 c SEE
c-3000 to 6000 d- 200 to 3000
Rotary type covering devices are used in____________-.
1336 d FMP
a-Planters b-Seed cum fertilizer drills c-Seed drills d-Both (a & c)
The critical shear stress τ, at which incident motion of sediment takes place, is
proportional to______________________.
1337 a- d1/2 b- d b ID
c-d2 d- none of above
where d is grain size
Water is pre treated and post treated in the case of ___________.
1338 a-Slow sand filter b-rapid sand filter b SEE
c-intermittent filter d-double filter
The value of n, in the equation PVn=C when the process is isothermal____________
1339 b FMP
a-Zero b-1 c-2 d-Infinity
The main function of diversion head-works provided at the off take of a canal from a
river is____________________.
1340 a ID
a- to raise water level in the river b- to control floods
c- store water d- control silt entry into canal
The influent for rapid sand filter should be treated earlier by ___________.
1341 a-Sedimentation with coagulation b- violent agitation a SEE
c- Aeration d- Chlorination
Washers are used____________.
1342 d FMP
a-Beneath bolt head b- beneath nut c-To hold two metal pieces d-Both (a & b)
An APM outlet is__________________.
1343 a- orifice b- weir a ID
c- meter d- none of them
The type of under drainage system provided in a rapid sand filter is ___________.
1344 a-Perforated pipe b- stoneware pipe a SEE
c- Loose jointed pipe d- None of the three
Cutting edge of share is called_____________.
1345 a FMP
a-Shin b-Frog c-Gunnel d-Skirt
Guide banks are provided____________________.
1346 a- in pairs b- asymmetrical in plan d ID
c- extending u/s and d/s of work d- all of them
Insufficient washing of sand grains in a rapid sand filter causes ___________.
1347 d SEE
a-Air binding b- Mud Balls c- Shrinkage of media d- Expansion of media
An apparatus used to obtain the volumetric chemical composition of the gaseous By-
products of combustion____________.
1348 b FMP
a-Bomb calorimeter b- Or sat analyzer
c-Chemical separator d-None of the above
A tile drain is laid below a cropped land to remove excess irrigation water. The
Drainage Coefficient of this drain is usually expressed as____________________.
a- cm of water removed from the drainage area per day
1349 a ID
b- cm of water removed per day
c- percentage of applied water, which is intercepted by this drainage
d- none of above
Pressure filter is used mostly in ___________.
1350 a-Urban water supply scheme b-Rural water supply scheme d SEE
c- swimming pools d- industrial scheme
1351 The ability of a heat engine to convert the supplied heat to work is referred to as a FMP
a-Thermal Efficiency b-Volumetric Efficiency c-Engine Efficiency d- none
Which of the following instruments is used for measuring radiation heat?
1352 a- barograph b- thermograph d ID
c- hair hygrograph d- pyranometer
The type of filter which is preferred for treating small quantities of water in railway
stations and individual industries is ___________.
1353 a-Slow sand filters b- pressure filters b SEE
c- rapid sand filter d- gravity filters
During combustion the pressure in the cylinder may increase to as much as______.
1354 a FMP
a- 50 Kg/cm2 b- 400 Kg/cm2 c- 10 Kg/cm2 d- 1 kg/cm2
For drainage works following type of pumps is used________________.
1355 a- radial flow b- axial flow b ID
c- mixed flow d- None of these
In double filtration, the name of the first filter is ___________.
1356 a-Roughing filters b- pressure filters a SEE
c-rapid sand filters d- gravity filters
The power used in overcoming friction in the engine is called_________.
1357 a FMP
a- FHP b- BHP c- IHP d- None of the Above
In a steady spatially-varied flow in a prismatic open channel, the_______________.
a- depth does not change along the channel length
1358 b- discharge is constant along the channel length c ID
c- discharge varies along the channel length
d- discharge is constant with respect to time
The object of treatment of water is to supply to consumers___________.
1359 a-Water free from all bacteria b-Water free from impurities d SEE
c-Water free from odor and color d-Potable water for daily need
The process extensively used for making nuts and bolts is__________.
1360 c FMP
a-Hot piercing b- hot spinning c- hot drawing d- Non
Cohesive force is minimum in___________________.
1361 a- sandy soils b- clayey soils a ID
c- clay-loam soils d- all above
Circle command can be selected from________________ toolbar
1362 b SEE
a-Modify b- Draw c- Dimension d- none
Hook’s Law holds up to______.
a-Yield point b- elastic limit
1363 b FMP
c- plastic limit d- breaking point
The relation among coefficients of discharge (Cd-, coefficient of velocity (Cv- and
coefficient of contraction (Cc- is_____________________.
1364 d ID
a- Cd = Cv + Cc b- Cd = Cv – Cc
c- Cd = Cv/Cc d- Cd = Cv. Cc
__________________ tool is used to create multiple copies in circular form
1365 a SEE
a-Polar array b- Rectangular array c- Copy d- Mirror
The ratio of linier stress to linier strain is called as_________.
1366 a FMP
a-Modulus of elasticity b- bulk modulus c- Poisson’s Ratio d- Non
Manning’s rugosity coefficient is proportional to_____________________.
a- d1/2 b- d
1367 c ID
c- d1/6 d- d2/3
where d is representative grain dia of bed surface
__________________ short key is used to select whole object
1368 a SEE
a-Ctrl + A b- Ctrl + Z c- F7 d- none
The modulus of elasticity for mild steel is approximately____________ kN/mm2.
1369 d FMP
a-80 b- 100 c- 110 d- 210
Fish ladder is provided on the side of___________.
1370 a- divide wall b- diaphragm wall a ID
c- corewall d- wingwall
Lines will draw perpendicular to each other when __________________ mode is ON
1371 b SEE
a-Osnap b- Ortho c- Polar d- none
The factor of safety for mild steel is ____________.
1372 b FMP
a-2 b- 4 c- 6 d- 8
An open flume outlet is________________.
1373 a- orifice b- weir b ID
c- meter d- none of them
____________________ tool is used to remove one portion of intersected lines
1374 a SEE
a-Trim b- Erase c- Fillet d- Cut
The ratio of the ultimate stress to the design stress is known as_________.
1375 c FMP
a- Elastic limit b- strain c- factor of safety d- bulk modulus
Length of guide banks u/s and d/s of the work are____________.
1376 a- the same b- more on u/s than in d/s b ID
c- less on u/s than in d/s d- as per site conditions
By layer option lies in _______________ toolbar
1377 d SEE
a-Draw b- Modify c- Dimension d- Properties
The factor of safe for steel and for steady load is__________.
1378 b FMP
a-2 b- 4 c- 6 d- 8
The method, which uses furrows on cropped farms for drainage of excess irrigation or
rain water, is called_______________.
1379 c ID
a- surface inlet b- tile drainage
c- bedding d- French drain
Copy command can be selected from ___________________ toolbar
1380 c SEE
a-Copy b- Draw c- Modify d- Dimension
An aluminum member is designed based on____________.
1381 a FMP
a- yield stress b- elastic limit stress c- proof stress d- ultimate stress
Which of the following rain gauges cannot be used for recording snow?
1382 a- weighing type b- float type c ID
c- tipping bucket type d- both a & b
To draw a line of 4 inch at 120o angle, the command prompt sequence will be written
1383 as follow_________. a SEE
a-@4<120 b- 4@<120 c- <120@4 d- 120<4@
In a body a thermal stress is one which arises because of the existence of
1384 ___________. FMP
b
a-latent heat b- temperature gradient c- total heat d- specific heat
For drainage works following type of impeller is used_________________.
1385 a- open impeller b- closed impeller a ID
c- semi-open impeller d- all of these
_______________ tool is used to create similar copy of an object to its opposite side
1386 c SEE
a-Copy b- Array c- Mirror d- Pan
A localized compressive stress at the area of contact between two members is known
1387 ______________. c FMP
a-tensile stress b- bending stress c- bearing stress d- shear stress
In a uniform flow in a channel of small bed slope, the hydraulic grade line
__________.
a-coincides with the bed
1388 b- is considerably below the free surface d ID
c-is considerably above the free surface
d- essentially coincides with the free surface
Shortcut key to ON/OFF ORTHO mode is __________.
1389 d SEE
a-F1 b- F2 c- F3 d- F8
The Poisson’s ratio for steel varies from____________.
1390 b FMP
a-0.21 to 0.25 b- 0.25 to 0.33 c- 0.33 to 0.38 d- 0.38 to0.45
A soil becomes more resistance to wind erosion at the moisture potential of
________.
1391 a ID
a- -1.5 MPa b- 1.5 MPa
c- 1.0 MPa d- none of above
Scale command lies in _________________ toolbar
1392 b SEE
a-view b- Modify c- Draw d- Visual Style
The stress in the bar when load is applied suddenly is ________as compared to the
1393 stress induce due to gradually applied load. b FMP
a-Same b- double c- three times d- four times
The discharge over a rectangular notch is_________________.
1394 a- directly proportional to H3/2 b- inversely proportional to H3/2 a ID
c- directly proportional to H5/2 d- inversely proportional to H5/2
_____________________ short key is used to undo previous operation
1395 d SEE
a-Ctrl Z b- Ctrl U c- U d- All
The energy stored in a body when strained within elastic limit is known as_________.
1396 c FMP
a- resilience b- proof resilience c- strain energy d- impact energy
The finer sediment which does not originate from the stream bed, but originate from
the catchment area, is best called as the __________________.
1397 c ID
a- bed load b- suspended load
c- wash load d- none of these
Except for 3 point, the Start- End- Direction and the Continuous options, arcs are
1398 always drawn by default in a __________ direction a SEE
a-Counter-clockwise b- clockwise c-both (a & b) d- left to right
The maximum energy that can be stored in a body due to external loading up to the
1399 elastic limit is called__________. b FMP
a- resilience b- proof resilience c- strain energyd- modulus of resilience
For a barrage, the exit gradient is independent of _________________.
1400 c ID
a- applied water head b- horizontal floor length
c- u/s cutoff depth d- d/s cutoff depth
Shortcut key to ON/OFF OSNAP is __________.
1401 c SEE
a-F1 b- F2 c- F3 d- F8
Spur gears are also called_____ gears.
1402 a FMP
a-Slow Speed b- roller c- straight d- none
A semi-modular outlet can distribute supply more or less_____________.
a- equitably in variation in levels in watercourse
1403 b ID
b- equitably in variation in levels in distributary/minor
c- all of above d- none of above
To draw a rectangle by using rectangle tool we need ___________ point/s.
1404 b SEE
a-1 b- 2 c- 4 d- 8
A rivet is specified by __________.
1405 a FMP
a- Shank diameter b- length of rivet c- type of head d- length of tail
Scour depth along guide banks is severer along________________.
1406 a- shank b- nose b ID
c- transition from nose to shank d- all of them
After selecting Circle command, Cursor turns into___________.
1407 a SEE
a-Plus sign b- circle sign c- square d-Pix box
The diameter of the rivet hole is usually_________ the nominal diameter of the rivet.
1408 a FMP
a-More than b- less than c- none of the above d-equal than
The material placed around the drains to avoid silt entry from drain joints________.
1409 a- gravel pack b- concrete pack c ID
c- pipe envelop material d- all of above
Shortcut key for PAN is _____________.
1410 b SEE
a-CTRL + P b- P c- PA d- none of these
The rivet head used for boiler plate riveting is usually__________.
1411 a-Snap head b- pan head a FMP
c- counter shank head d- conical head
The capacity of one bucket in tipping bucket rain gauge is_______________.
1412 a- 0.25 mm b- 0.5 mm a ID
c- 1.5 mm d- 1.25 mm
_________ command is used to apply a material symbol to the drawing
1413 b SEE
a-Color b- Hatch c- Pattern d- Symbol
A line joining the center of the rivet and parallel to the edge of the plate is known
1414 as__________. b FMP
a-Back pitch b- marginal pitch c-gauge line d- pitch line
For drainage works following type of pump is used_____________.
1415 a- high head low discharge b- low head high discharge b ID
c- all of above d- none of above
Shortcut to save a file in JPG is _____________.
1416 a SEE
a-JPG OUT b- Ctrl + JPG c- .JPG d- NONE
The centre to centre distance between two consecutive rivets in a row is
called___________.
1417 b FMP
a- margin b- pitch
c- back pitch d- diagonal pitch
1418 A uniform flow takes place in a steep channel of large slope. The hydraulic grade line d ID
is_______
a- coincides with the bed b- essentially coincides with the free surface
c- is above the free surface d- is below the free surface
The environment where the users create images is ________________.
1419 b SEE
a-Paper b- Model c- Drawing Sheet d- None of these
The objective of caulking in a riveted joint is to make the joint __________.
1420 a- free from corrosion b- stronger in tension d FMP
c- free from stresses d- leak proof
Gravity force opposes the _________________.
1421 a- soil lift b- initiation of movement c ID
c- soil entrainment d- both (a- and (b-
The extension to Save an AutoCAD file is__________.
1422 c SEE
a-*.JPG b- *.DIF c- *.DWG d- None of these
A lap joint is always in _________ shear.
1423 a- single b-double a FMP
c- both a&b d-none of these
The loss of head due to friction according to Darcy’s formula is____________.
1424 a- f.L/D.v2/2g b- 4f.L/D.v2/2g a ID
c- f.L/D.v2/2 d- f.L/D.v/2g
The tool used to round off corners is _____________.
1425 a SEE
a-Fillet b- Chamfer c- Radius d- None
A double strap butt joint (with equal straps- is _________.
1426 a- always in single shape b-always in double shape b FMP
c- both a&b d- all of above
The force exerted by the flowing water on the sediment particles to cause their
motion, is called______________________.
1427 b ID
a- buoyant force b- tractive force
c- kinematic force d- eddy force
To find the Area/Perimeter/Distance/Region of drawing _________tool is used.
1428 a SEE
a-Inquiry b- Dimension c- Both d- None
Which of the following riveted butt joints with double straps should have the highest
efficiency as per Indian boiler regulation ___________.
1429 c FMP
a- single riveted b-double riveted
c- quadruple riveted d- both a & c
The characteristic feature of barrage is_________________.
a- provision of raised crest b- creation of storage reservoir on u/s
1430 c ID
c- provision of a series of gates across the river for flow regulation
d- that is built in delta areas only
Wood is superior in ____________ than concrete
1431 a SEE
a-Compression b- strength c- toughness d- resilience
If the tearing efficiency of a riveted joint is 50% then ratio of diameter of
to the pitch of rivet is __________.
1432 c FMP
a- 0.20 b- 0.45
c- 0.50 d- 0.60
A non-modular outlet supplies water depending on:
1433 a- water level in the distributary/minor b- water level in the watercourse c ID
c- water level in the canal/watercourse d- All of above
To get full strength of concrete curing time should be_________.
1434 d SEE
a-3 days b- 7 days c-14 days d-28 days
The longitudinal joint in boiler is used to get the required _________.
1435 a- length of boiler b- diameter of boiler b FMP
c-both a & b d-efficiency of boiler
Spurs are aligned on the river bank in a direction________________.
1436 a- normal to dominant flow discharge b- at right angle pointing upstream d ID
c- at right angle pointing downstream d- all of them
Drying of wood is done to avoid_________.
1437 a SEE
a-Shrinkage b-strength c-hardness d-change in mass
For longitudinal joint in boilers, the type of joint used is __________.
a- butt joint with double cover plates
1438 b- butt joint with single cover plate a FMP
c- lap joint with one ring overlapping
d-any one of the above
The most important soil property for constructing mole drain is________________.
1439 a- texture b- elasticity c ID
c- plasticity d- none of above
Resistance of material to passage of liquid is called_________.
1440 c SEE
a-Ease of cleaning b- resilience c-imperviousness d- scratch
According to Indian standards, the diameter of rivet hole for a 24 mm diameter of
rivet, should be_____________.
1441 c FMP
a- 23 mm b- 24 mm
c- 25 mm d- 26 mm
For saturated condition, when humidity is 100%, the difference between dry bulb and
wet bulb temperatures is______________.
1442 d ID
a- maximum b- relatively high
c- negative d- zero
The property associated with high density of surface and hardness is called________.
1443 a SEE
a-Ease of cleaning b- resilience c-imperviousness d- scratch
The largest diameter of an external or internal screw thread is known as____.
1444 a- minor diameter b- major diameter b FMP
c- pitch diameter d- none of these
Cavitation is the process of ___________________.
a- filling the suction line and pump casing with the working fluid
1445 d ID
b- pumps selection c- pump maintenance
d- bubble formation
Wood is classified into two main groups_________.
1446 d SEE
a-Deciduous b-coniferous c-broad leaves d-both a and b
The pitch diameter is the ________ diameter of external or internal thread.
1447 a- effective b- smallest a FMP
c- largest d- none of these
One dimensional of flow analysis means______________________.
a- uniform flow b- steady uniform flow
1448 c ID
c- neglecting the variation in the transverse direction
d- neglecting the variation in the longitudinal direction
At a junction of tree trunk and limbs _________.
1449 c SEE
a-Growth defect b-seasoning defect c-knots d-lumber grades
A screw is specified by its _______________.
1450 a- major diameter b- minor diameter a FMP
c- pitch diameter d- pitch
An erosion, in which rate of soil loss exceeds the rate of soil formation is referred
as___
1451 a ID
a- accelerated erosion b- normal erosion
c- glacial erosion d- chemical erosion
Work is intentionally of good quality if wood is _________.
1452 a SEE
a-Well-seasoned b- knots c- shake d-decayed
The railway carriage coupling has __________.
1453 a- square thread b- acme thread d FMP
c- knuckle thread d- buttress thread
The hydraulic radius for a circular pipe of diameter D is______________.
1454 a- D/2 b- D/3 c ID
c- D/4 d- D/6
At a result of destructive activity of certain types of fungi wood is _________.
1455 b SEE
a-Pitch pockets b- decay c- shake d-mineral steaks
The square threads are usually found on ________.
1456 a- spindle of bench vices b- railway carriage coupling c FMP
c- feed mechanism of machine tool d- none of these
The tractive force method of designing stable channels in non-cohesive soils, is
application only when the channels________.
1457 a- Carry sedimented water b- carry clear water b ID
c- carry sedimented water, but sediment concentration does not exceed 500 ppm or so
d- carry any type of water
The opening between annual rings which contains free resins_________.
1458 a SEE
a-Pitch pockets b- decay c- shake d- mineral steaks
A locking device in which the bottom cylindrical portion is recessed to receive the tip
of the locking set screw is called__________.
1459 c FMP
a- castle nut b- jam nut
c- ring nut d- screw nut
Khosla theory is applicable to structures founded on____________.
1460 a- rock b- any type of material c ID
c- permeable material only d- none of above
Due to overstressing of standing timber, separation produced by wind is_________.
1461 c SEE
a- Pitch pockets b-decay c-shake d- mineral steaks
Which one is not a positive locking device ________.
1462 a- spring washer b-cotter pin a FMP
c- tongued washer d- spring wire lock
Adjustability of semi-modular outlet is most convenient and economical in_______.
1463 a- AOSM b- open flume a ID
c- both of them d- none of them
The brown and black discoloration caused by oxidation is called_________.
1464 d SEE
a-Pitch pockets b- decay c- shake d- mineral steaks
The washer is generally specified by its ____________.
1465 a- outer diameter b- hole diameter b FMP
c- thickness d- mean diameter
Spurs serve to train the river in order to_______________.
a- Reduce concentration of flow at the point of attack
1466 d ID
b- guiding and deflecting axis of flow
c- protecting on eroding bank tropping bank load d- all of them
The mixture of lime stone and clay is called_________.
1467 a SEE
a-Cement b- sand c- concrete d-mortar
A locking device extensively used in automobiles industry is a________.
1468 a- jam nut b- castle nut b FMP
c- screw nut d- ring nut
The fastest method of drainage to lower WT to greater depths is_____________.
1469 a- Surface drainage b- subsurface drainage c ID
c- vertical drainage d- none of above
The most essential component of concrete is_________.
1470 c SEE
a-Cement b- sand c- water d- mortar
A bolt of M 24*2 means that _________.
a- the pitch of the threads is 24 mm and depth is 2 mm
1471 b- the cross sectional area of threads is 24 mm square c FMP
c- the nominal diameter of bolt is 24 mm and the pitch is 2 mm
d- none of these
Precipitation that occurs due to lifting of moist air after striking with mountain
barriers is called___________________.
1472 c ID
a- convectional precipitation b- frontal precipitation
c- orographic precipitation d- cyclonic precipitation
Which one is not affecting the strength of concrete_________.
1473 d SEE
a-Composition b- curing time c- water d- stress
When a nut is tightened by placing a washer below it the bolt will be subjected to
__________.
1474 a FMP
a- tensile stress b- compressive stress
c- shear stress d- none of these
Output of pump is called_________________.
1475 a- Output horse power b- Input horse power c ID
c- Water horse power d- Brake horse power
Mixture of clay and powered glass is called_________.
1476 d SEE
a-Pre stressed Cement b- silica c- concrete d-mortar
Eye bolts are used for ____________.
1477 a- transmission of power b- locking device c FMP
c- lifting and transporting heavy machine d- none of these
The velocity and depth of flow in 3.0 m wide rectangular a channel are 2.0 m/s and
2.5 m, respectively. If the channel has its width enlarged to 3.5 m at a section. The
1478 discharge past that section is_______________. c ID
a- 10.0 m3/s b- 20.0 m3/s
c- 15.0 m3/s d- 17.5 m3/s
1479 The material which gives well finish is_________. b SEE
a-Metal sheet b- plaster c-mortar d- concrete
The shock absorbing capacity of a bolt may be increased by __________.
1480 a- increasing its shank diameter b- decreasing its shank diameter b FMP
c- tightening the bolt properly d- none of these
Gully erosion is the advance stage of______________.
1481 a- splash erosion b- sheet erosion b ID
c- rill erosion d- tunnel erosion
Structural frames used in multistory poultry houses are_________.
1482 a SEE
a-Beam and post b-trusses c-arch d-braces
The resilience of the bolt may be increased by ___________.
1483 a- increasing its shank diameter b- increasing its length b FMP
c- both a & b d- none of these
The energy line lies over the hydraulic gradient line by an amount equal to________.
1484 a- v2/2g b- v2/g a ID
c- v/2g d- v/g
A jointed frame that is used to support load over a relatively long span_________.
1485 b SEE
a-Beam and post b- trusses c- arch d-braces
In _______ gear, teeth are made parallel to axes of shaft or wheel
1486 b FMP
a-Helical b- Spur c- Worm d- None
The Lacey’s and kennedy’s empirical silt theories for designing irrigation channels in
non-cohesive soils, are meant to ensure_________.
a- no scouring in the channel
1487 c ID
b- no silting from out of the sedimented water entering the channel from the
headworks
c- both a and b d- neither a nor b
A type of structure is used where a high rise and floor of obstruction are desired____.
1488 c SEE
a-Beam and post b- trusses c-arch d- braces
Bevel gear is used to________
1489 a-Transmit power at 900 b-Change speed a FMP
c-Rotate the fly wheel in engine d- Reduce speed
Khosla theory of independent variables is applicable to structure on________.
1490 a- rock b- clay b ID
c- sand d- concrete
A form of energy which is convertible at any time_________.
1491 a SEE
a-Heat b- temperature c- none d- both a and b
_______ gear system is used in steering mechanism.
1492 c FMP
a-Spur b- Face c- rack and pinion d- none
In the ascending order of consumption of head, the outlets are__________.
1493 a- AOSM, open flume, pipe b- AOSM, pipe, open flume d ID
c- open flume, ASOM, pipe d- pipe, open flume, AOSM
Ability of body to give up or receive heat _________.
1494 b SEE
a-Heat b- temperature c- none d- both a and b
Ratio of load to the force applied is called______
1495 a FMP
a-Mechanical advantage b- Force ratio c- velocity ratio d- None
Spurs serve to_______________.
1496 d ID
a- repel flow b- attract flow
c- deflect flow d- all of them
The temperature of surrounding medium is called _________.
1497 c SEE
a-Heat b- latent heat c- ambient temperature d- sensible heat
______ Type of gears are used in conveyor systems.
1498 C FMP
a-Straight gears b- Chain gears c- Sprockets d- None
The type of drainage that may dispose-off excess runoff and -lower WT is_____.
1499 a- Surface drainage b- subsurface drainage A ID
c- vertical drainage d- none of above
Co efficient of thermal capacity of a material to that of water is called_________.
1500 a-Specific heat b- latent heat A SEE
c- ambient temperature d- sensible heat