Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or
part of the products, services and features described in this document may not be within the purchase scope or the usage
scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are
provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the preparation
of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document
do not constitute the warranty of any kind, express or implied.
1
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol Description
Indicates a potentially hazardous situation, which if not avoided, could
CAUTION result in equipment damage, data loss, performance degradation, or
unexpected results.
Provides additional information to emphasize or supplement important
NOTE points of the main text.
Change History
Changes between document issues are cumulative. Therefore,the latest document issue contains all the
Changes in previous issues.
2
AP6510DN-AGN
Quick Start Guide
Please download the detailed product documents from "http://support.huawei.com/support/".
The detailed path is as follows: Technical Support->Documentation->Access Network -> WLAN ->WLAN -> Product
Documentation -> AP6510DN.
Before performing Installation, confirm that the installation accessories and tools are available. 技术支持
Technical Support
Installation accessories: Installation tools:
Huawei Technologies Co., Ltd.
Flat-head Phillips Combination Diagonal Adjustable 6mm drill Address:Administration Building,Huawei
screwdriver screwdriver pliers pliers wrench Hammer bit Technologies Co., Ltd.,Bantian,Longgang
District,Shenzhen,People’s Republic of China
Installation Expansion M4X12 hexagon
Postcode:518129
suite bolt socket head cap ESD COAX Measuring Hex key
Maker Utility knife Level Email:support@huawei.com
screw gloves crimping tool tape Website:http://www.huawei.com
Packing List
Unpack the equipment. Ensure that all items listed in the package list are included in the shipment. If any item is missing,
contact the supplier.
4 M4X12 hexagon socket head cap screw 4 PCS Certificate of Conformance 1 PCS
10
6 Hoop 2 PCS
Device Overview
Product functions
4 321 5
SN Item Description 7 7 6 6
1 Wireless Wireless status indicator.
3
Installing an AP
● Select an appropriate installation position and leave space above and around the device for cooling air circulation.
● Outdoors APs are used for hotspot coverage and often installed against walls or poles. The pole diameter is 30 to 114 mm.
AP6510DN dimensions (unit: mm) without a backplane support Recommended AP6510DN installation space (unit: mm)
330 83
306
Flat washer
Spring washer
Nuts
3. Use four M4*14 hexagon socket head cap screws to fasten the wall-mounting bracket to the AP.
Hexagon
socket head
cap screw
4. Pinch the wall-mounting bracket on the expansion
5. Slide the AP into the wall-mounting bracket to complete
bolts, and fasten the Flat washer, spring washer, and
installation.
nuts in order.
Field strength
场强示意
4
Installing an AP
● Installing the AP6510DN against a vertical pole:
1. Determine the AP installation position, slide the hoop 2. Slide the AP that has the connector fastened into the wall-
through the hole of the wall-mounting bracket and attach mounting bracket.
it to the pole, And use the screwdriver to secure screws
on the hoop.
Field strength
场强示意
● The procedure for installing the AP6510DN against a horizontal pole is similar to the procedure for installing the AP6510DN
against a vertical pole.
3 上电调试
Security
lock
Lock hole
NOTE
To prevent unauthorized personnel from moving the AP, lock the AP. The preceding figure shows the security lock. The
carrier should purchase the security lock and determine the position for installing the security lock.
5
Installing Cables
● AP6510DN external cable arrangement drawing
Feed line Feed line
Ground cable
Network cable
4 Blue 4
6 Green 6
8 Brown 8
3. Put the network cable through the hole on the waterproof PG connector.
Waterproof PG connector
a b c d
4. Connect the RJ45 connector to the AP and secure the waterproof PG connector, as shown in figures b, c, and d.
a b c d
CAUTION
Ensure that the RJ45 connector is correctly connected to the AP. Otherwise, the network cable may be damaged.
Before removing the network cable, remove the waterproof PG connector, and then remove the RJ45 connector from
the AP.
6
Installing Cables
● Connecting the feed line
1. The outdoor AP's antenna ports already have 5 KA surge protection capability. Generally, no surge protection devices
need to be installed; therefore, the antenna cables are directly connected to the AP's antenna ports.
2. If higher surge protection capability is required, the customer can purchase a surge protection device. When installing the
surge protection device, ensure that it is connected to a ground cable.
a b c
Surge
protection
device
Ground cable
Waterproof
Feed line adhesive
tape
NOTE
● Wrap the feed line using one-layer PVC black insulation tape, three-layer waterproof adhesive tape, and then three-layer
PVC black insulation tape.
● Stretch the waterproof adhesive tape evenly and ensure that the upper layer of the tap overlaps 1/2 of the lower layer.
Each layer should be attached tightly.
● Wrap the three-layer waterproof adhesive tape from bottom to up, from up to bottom, and from bottom to up in order.
CAUTION
Keep the screw properly and install it again after pressing the Reset button.
7
Installing Cables
● Requirements for Laying Out Cables
● Requirements for laying out power cables
1. The power cable must be separated from ground cables and signal cables.
2. If multiple power cables are installed, you must bind the power cables.
3. The routing of power cables must meet engineering design drawing requirements.
4. If the power cable length is insufficient, replace the power cable. The power cable must be complete and cannot
have splices or welding points.
● Requirements for laying out ground cables
1. All ground cables must be connected to a ground bar.
2. The ground cable cannot be led in aerially, but buried in the earth or arranged indoor.
3. Both ends of the external conductor of the coaxial cable and those of the insulation of the shielded cable should
have good electric contact with the metal shell of the equipment they connect to.
4. Ground cables must be separated from signal cables to reduce interference between them.
5. Do not add any switch or fuse on the ground cable.
6. Do not use another device for an electrical connection with the ground cable.
7. All metal components in the shell must be securely connected to the ground cable.
● Requirements for laying out optical fibers
1. Do not press optical fibers forcibly or crush optical fibers with force. Leave sharp objects away from optical fibers
to prevent damage to optical fibers.
2. Coil up redundant optical fibers round specialize devices such as the splice tray.
3. Coil optical fibers gently and do not break them.
4. Cover optical fiber connectors with protective caps.
8
Power-on
NOTE
2 连接线缆
Power on the AP6510DN and check the indicator status to determine the system
running status.
Steady red Off Off The system fails to load the DRAM or system software.
Blinking green and The system is working properly, but the Ethernet is not
yellow alternately connected. STAs at 2.4 GHz and 5 GHz are connected.
Technical Specifications
Item Description
Weight 2.2Kg
Dimensions (H x W x D) 83mm×255mm×255mm
9
Logging In to the Router
After an AP is powered on, you can log in to the AP using the following methods.
1. Logging In to the AP Using Telnet
This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using
commands.
Procedure
Step 1 Connect a PC to the uplink port of the AP with a network cable. Figure 1-1 shows the location of the AP's uplink
port.
No Port
1 ETH/PoE
Step 2 Configure a static IP address for the PC. The IP address must be on the network segment 192.168.0.1/24
(The IP address should not be same as the AP's default IP address 192.168.0.1.) and the subnet mask is
255.255.255.0.
After the configuration is complete, run the ping 192.168.0.1 command on the PC to check whether the PC
can be pinged. If the ping operation succeeds, the connection is set up successfully. If the ping operation fails,
The connection fails to be set up. Check whether the network cable works properly.
Step 3 Access the command line window on the PC. For example, if the PC runs Windows XP, choose Start > Run
And enter cmd in the displayed dialog box.
Step 5 Enter the default user name and password admin. If the user view is displayed, you have logged in
Successfully.
When you log in for the first time, the following page is displayed:
Username: super
Password:
Enterprise AP:
----End
10
AP Local Configuration
WLAN services parameters of an AP are configured on the AC that is connected To the AP, and then delivered to the AP.
The following parameters are configured on the AP through Telnet.
1. Configuring the AP Access Mode
This section describes how to configure the mode in which an AP goes online.
2. Configuring VLANs on Wired Interfaces of an AP
This section describes how to configure VLANs on wired interfaces of an AP.
3. Configuring WDS
This section describes how to configure WDS parameters on an AP.
1 Configuring the AP Access Mode
This section describes how to configure the mode in which an AP goes online.
● AP Access Modes
After an AP starts, going online management module determines the mode in which the AP goes online. Users are
unaware of the AP access mode. In the AP startup phase, the AP obtains the its IP address, the gateway IP address,
and the AC IP address based on the access mode. After obtaining all the information, the AP sets up a Control And
Provisioning of Wireless Access Point (CAPWAP) link with the AC. The process is as follows:
1. The AP reads the configuration file and determines the mode to go online.
2. If the DHCP mode is used, the AP starts the DHCP process.
3. If the static mode is used, the AP starts the AC discovery process based on the static configuration, and
establishes a control tunnel with the discovered AC.
4. If the PPPoE mode is used, the AP initiates the PPPoE dial-up process. After obtaining the management IP
address and gateway address, the AP uses the statically configured AC IP address to discover the AC, and
establishes a control tunnel with the AC.
NOTE
By default, AP's go online in DHCP mode.
NOTE
● After the configuration is complete, run the reboot command to restart the AP.
● After the configuration is complete, run the show sysinfo command to check the configuration.
Enterprise AP(if-ethernet) # show sysinfo
ap_ipmode=pppoe
ap_ipaddr=
ap_ipversion=4
ap_netmask=
ap_gateway=
ac_ip1=
ac_ip2=
ac_ip3=
ac_ip4=
pppoe_username=wlan@huawei
pppoe_pwd_type=simple
pppoe_password=wlan@huawei
2. Configuring VLANs on Wired Interfaces of an AP
This section describes how to configure VLANs on wired interfaces of an AP.
● Introduction to the Wired Interfaces
A wired interface on an AP is connected to an AC or a switch. When the AP assigns service VLANs to packets, you can
configure VLANs on wired interfaces of the AP.
●Configuring VLANs on a Wired Interface
NOTE
By default, the PVID of a wired-side interface is 0, and no VLAN is configured on the interface.
NOTE
The configuration takes effect immediately, and you do not need to restart the AP.
12
AP Local Configuration
3. Configuring WDS
This section describes how to configure WDS parameters on an AP.
● Introduction to WDS
WDS enables multiple AP6510DNs to establish wireless links to connect two or more wired or wireless LANs. WDS-
enabled AP6510DNs can switch data packets between the LANs. WDS facilitates network deployment, and device
installation, and allows flexible networking.
● Configuring WDS
Most WDS parameters are configured on the AC. For details, see the AC configuration guides. On an AP, you can enable
or disable the radio indicator that indicates the signal strength of the last hop bridge, and configure the WDS keys.
● Enabling/Disabling the radio indicator that indicates the signal strength of the last hop bridge.
NOTE
By default, the radio indicator is enabled on an AP6510DN.
NOTE
By default, the radio indicator is enabled on an AP6510DN.
NOTE
After the configuration is complete, run the reboot command to restart the AP.
13
Declaration on Hazardous Substances in Electronic
Information Products
Hazardous Substances
Part
Pb Hg Cd Cr6+ PBB PBDE
Mechanical part O O O O O O
Board/circuit module O O O O O O
Signal cable O O O O O O
Cable connector O O O O O O
Power adapter O O O O O O
Auxiliary equipment O O O O O O
O: Indicates that the concentration of the hazardous substance contained in all the homogeneous materials of this part is
below the limit requirement of the SJ/T 11363-2006 standard.
X: Indicates that the Concentration of the hazardous substance contained in all the homogeneous materials of this part is
above the limit requirement.
QUALIFICATION CARD
14
Warranty Card
Thank you for choosing HUAWEI Technologies Co., Ltd-a leading telecom solution provider. To get better services, please
read this warranty card carefully, fill in the required information and preserve this card in good condition.
Your Name
Address/Postal Code
Telephone
Product Type
Purchase Date
Invoice Number
Dealer Name
Dealer´s Address/Telephone
Subject to the exclusions contained below, Huawei Technologies CO., Ltd. (hereinafter referred to as Huawei) warrants its
access terminals (“Products”) to be free from defects in materials and workmanship under normal consumer usage for one
year from the date of purchase of the product ("Warranty period"). During the warranty period,a Huawei authorized
service partner shall remedy defects in materials and workmanship free of charge.
Special Notice:
1. The warranty card shall be applicable only after being stamped by the dealer.
2. The warranty card must be preserved in good condition and free of any scratch or alteration.
3. To claim such service for defects that are not included in The following exclusion terms, the warranty card and the
invoice that records the product serial number shall be presented to a Huawei authorized service partner.
Exclusions:
In any of the following cases, the warranty card becomes unenforceable or inapplicable without prior notice:
1. The defects are caused by improper handling in transportation and assembly.
2. The defects are caused by the fact that the product is dismantled or altered by anyone that is not from a Huawei
authorized service partner.
3. The defects are caused by the fact that the product is used in a harsh environment that is not suitable for the operation
of the product.
4. The defects are caused by any force majeure including but not limited to fire, earthquake, lightning and tsunami.
5. The defects are caused by the fact that the product is used or handled improperly, roughly or not as instructed in the
applicable User Guide.
6. The normal wear and tear, including but not limited to the normal wear and tear of the shell and the power module, shall
not be covered by the limited warranty.
7. The warranty card is altered or illegible, or the product serial number recorded on the warranty card is inconsistent with
the actual one imprinted or labeled on the product.
In any case that is not covered by this limited warranty or should the warranty expire,Huawei shall charge for the
service(s) claimed for the products if the product is still remediable.
Huawei preserves the right for interpretation of this limited warranty.
15
HUAWEI TECHNOLOGIES CO., LTD.
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
www.huawei.com
Part Number: 31505366 Issue: 01