Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
blasthole drill
The Sandvik D50KS is a diesel powered, self-propelled drill pipe. First pass capability is 8,7 m (28' 6"). The
crawler mounted blasthole drill for mining. It is a maximum pulldown is 222 kN (50 000 lb) and bit
powerful mid-range production drill and comes with a load 267 kN (60 000 lb). Thanks to its heavy duty
low pressure air compressor for rotary drilling. Its hydraulic system, the D50KS delivers the rotary
normal range is 152 to 229 mm (6" to 9") diameter horse power for maximum productivity throughout
holes, but it can optionally drill up to 251 mm (9 7/8") its hole size range.
hole size. Maximum hole depth is 45 m (148') with 7"
D50KS undercarriage
Main rails: Wide flange beam main rails with heavily cross bracing
and reinforced at high stress areas. CAD designed.
Material: 14" x 74 lb/ft WF, ASTM alloy A572, Grade 50 steel
Construction: Electric spray transfer welding method
Jack, mast, deck supports: Welded integrally
Battery box: Lockable door left front corner of frame
Right deck: Non-skid, 609 mm (24") wide
Handrails: 42 x 1067 mm (1 - 21/32" dia. x 42") high w/ kick board
Tow hooks: Welded, 2 front, 2 rear
Leveling jacks
Number: Three
Cylinder bore: 152 mm (6") diameter
Cylinder rods: 76,2 mm (3") diameter, chrome plated
Cylinder stroke: 1,2 m (48")
Lift capacity each: 32 063 kg (70 686 lbs)
Pad connection: Ball and pinned socket
Pad diameter: 610 mm (24")
Safety check valves: Integral in each cylinder
Extension boot: 219 mm (8 5/8") diameter x 8,2 mm (5/16") wall
Pad ground clearance: 24" (610 mm) front, 457 mm (18") rear when retracted
D50KS power group
Compressor
Type: Oil flooded screw, single stage
Inlet: 29,7 m3/min (1050 cfm)
Max operating pressure: 6,9 Bar (100 psi)
Intake air cleaner:
Type - Dry type with safety element
Rating - 49,8 m3/min (1760 cfm) @ 254 mm (10") of H2O
Oil cooling: Thermostatically controlled radiator
Oil separation: Vertical barrier element, pre-separated in 265 L
(70 gal) horizontal sump
Oil filtration: 25 μm (25 micrometer) replaceable element
Drive: Direct to engine flywheel thru soft coupling
Controls: Automatic with safety shutdown system
Air shut off: Hydraulically controlled at panel
Connection to rotary head: 50,8 mm (2") shock mounted steel piping and air hose
D50KS mast
Hydraulic oil cooling system Oil cooler with 60°C (140°F) thermostats
Oil reservoir: 511 L (135 gal) w/sight glass and temperature gauge
Reservoir pressurization: 34,5 kPa (5 psi) air, filtered breather
Pump inlet supercharge: 1,2 MPa (175 psi) for rotation, feed and track
Reservoir refill system: Hand pump thru 10 μm (10 micrometer) in-tank filters
System refill capacity: 700 L (185 gal)
D50KS angle drilling (option)
Angle position lock system: Two pins lock drill table to mainframe
Position locking means - Hydraulically actuated from operator’s console
Pin size - 76 mm (3") diameter
Angle range - 0° to 30°
Angle increments - 5°
Pin lock indicators - Light indicator in cab-lock/unlock
Auxiliary pipe support: V-block type
Location - Inside mast
Pipe support bracket - Stationary V for all pipe sizes
Power - Hydraulic cylinder
Adjustable work deck:
Work deck leveling - Adjustable to 30°
Adjustment means - Deck pivots at rear of table
Position locks - Adjustable length chains to table
Table to deck dust seal - Two pieces, 7,87 mm (5/16") rubber compound
in sliding holder under deck
Loader booster cylinder: Additional swing cylinder at top of loader
assures thread alignment
D50KS options
Paint Single paint color other than standard - Orange, Grey & White
Training One week start up - USA/Canada
One week start up - International
Additional day of start up training (12 hr)
Power Group C15 402 kW, 37,4 m³/min / 6,9 Bar (1323/100)@1800 RPM
QSX15 417 kW, 29,7 m³/min / 6,9 Bar(1050/100)@1800 RPM
QSX15 417 kW, 37,4 m³/min / 6,9 Bar (1323/100)@1800 RPM
Air volume control for low pressure compressor
Service walkway around exhaust and front (cooler) sides
Dust Control Water injection 34 L/min (9 gpm) with 757 L (200 gal) tank
Water inj 34 L/min (9 gpm), 1,514 L (400 gal) (not w/ dry dust)
Sandvik dry dust collector, 102 m³/min (3600 scfm)
Tipton dry dust collector, 130 m³/min (4500 scfm)
Rotary Head Rotary head speed 0 -152 RPM, torque 8221 Nm (72 762 in-lb)
Rotary head speed 0 -188 RPM, torque 6643 Nm (58 793 in-lb)
Rotary head, dual speed 0 -126 RPM and 0 -194 RPM
Heavy duty head 5 1/2" API Box for 24,1 Bar (350 psi)
Angle Drilling Angle drilling 0°-30° in 5° increments with loader booster
Mast Equipment Extended mast, 10 m (33') single pass, with standard loader
Auto tong group
Pipe thread greaser operated from inside cab
Lubrication Air line lubricator 114 L (30 gal) reservoir
Central lube system, manual via central point
Central lube system, automatic, 19 L (5 gal)
Pre-start lubrication pump
Remote oil drain system (engine and gear boxes)
Fluids service center, fill, and hydraulic evacuation
SOS sample system for engine, compressor and hydraulics
Electrical Battery disconnect system (included in CE group)
Premium lighting upgrade, 12 lights and 175 Ampere alternator
24 Volt to 12 Volt converter
Compressed Air Cleaning kit, air gun with 7,6 m (25') hose
Cleaning kit, air gun with 15,2 m (50') hose with reel
Operator’s Cab Drill monitoring system (DMS)
Electronic depth counter (EDC), Imperial
Electronic depth counter (EDC), Metric
Cab sun shades
Window wiper, front, rear, windows, and washers
Extended cab
Electric controls for tramming, mast, and leveling
Remote tramming (requires electric controls)
D50KS options
Dimensions
Length, mast down: 14,2 m (46' 7") from cab roof to piping support
with rotary head at top of mast
Length, mast up: 9,45 m (31') from cab roof to jack pad at front of frame
Width, operating: 4,42 m (14' 6") from dust collector to cab
side walkway
Width, shipping: 3,81 m (12' 6")
Width over track shoes: 3,68 m (12' 1")
Height, mast down: 4,45 m (14' 7") with work deck removed
and safety hoop in place
Height, mast down: 5,82 m(19' 1") with work deck on
Height, mast up: 14,3 m (46' 9") from ground to piping support
with rotary head at top of mast
Weights
Bare weight (less tools): 43 545 kg (96 000 lbs)
Bare weight, std base only: 32 659 kg (72 000 lbs)
Bare weight, mast assy only: 10 886 kg (24 000 lbs)
Sandvik is a high-technology engineering group with world-leading
positions in selected areas – tools for metal working, advanced
materials technology, and mining and construction. We are
represented in 130 countries.