Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
G
F
B
E
C
D
No. Name
A Multifunction Button
H LED Indicator
1
Charging
The LED indicator will flash red if the battery level is low, which
indicates charging is necessary.
1. Plug the USB end of the charging cable to a USB charging port or
any active USB port (charging power: DC 5V).Connect the Micro
USB end of the charging cable to the charging port of the BR1005.
2. The LED indicator will turn red when charging.
3. The LED indicator will automatically turn off when the device is
fully charged. It takes up to 2.5 hours to fully charge the Bluetooth
adapter.
Note:
a. Poor quality power adapters do not provide a stable current ,
which may generate current noises when using.
b. To avoid battery over-discharge, please recharge the device once
a month if the device is not in regular use. Lithium-Ion batteries
continue to slowly discharge (self-discharge) when not in use or
while in storage.
Common Functions
1. Power On/Off
Press and hold the Multifunction Button for 3 seconds.
Power on: the LED indicator will blink blue.
Power off: the LED indicator will blink red and automatically turn off.
2. Automatically Pairing with Previously Paired Devices
BR1005 will enter pairing mode automatically when powered on for
the first time. BR1005 can remember previously paired devices and
will attempt to pair with devices automatically, without going into
pairing mode.
3. Quickly Enter Pairing Mode
Quickly double-click the Multifunction Button to enter pairing
mode after the BR1005 is powered on.
4. TX/RX Mode Switch
TX/RX mode can only be successfully switched after the adapter is
turned off for 5 seconds.
Note: turn off the BR1005 and restart it after 5 seconds if the mode
switch is not functioning properly.
2
5. Clear Pairing History
Please follow the guides below to clear the pairing history if pairing
failures are encountered:
1) Turn off the BR1005, switch TX (RX) mode to RX (TX) mode after 5
seconds, and then restart the BR1005.
2) Turn off the BR1005, switch RX (TX) mode to TX (RX) mode after
5 seconds. After that, the pairing history of TX (RX) mode will be
cleared.
6. AUX and SPDIF Mode Switch
You can freely switch between SPDIF and AUX mode. In SPDIF
mode, connect devices through SPDIF IN for TX mode and SPDIF
OUT for RX mode.
7. RX Mode: Pause/Play
Press the Multifunction Button to pause or play while playing music.
8. Auto-off
In RX mode, the BR1005 will automatically power off if there is no
device to be connected within 6 minutes. The BR1005 will not turn
off automatically in TX mode.
3
LED Indicator
LED Indicator (TX Mode) Status
Blue LED flashes twice every 3 seconds Automatically Pairing with Previously Paired Devices
How to Use
1. Pairing
1) Set your Bluetooth enabled devices like Bluetooth headphones or
speakers to pairing mode.
2) Set the BR1005 to TX mode. Then press and hold the Multifunction
Button for 3 seconds to turn it on. Tap the Multifunction Button
twice to enter pairing mode with the LED indicator keeps rapidly
flashing blue. The BR1005 will automatically exit pairing mode if
there is no device to be connected within 2 minutes.
3) Place your Bluetooth audio receiving devices like earphones or
speakers closely to the BR1005. After approximately 30 seconds,
pairing will be completed. The BR1005 LED indicator will turn solid
blue.
4) Switch between AUX and SPDIF mode. Connect the BR1005 to
your audio output devices like TV through a 3.5mm audio cable or
optical digital cable.
Note:
a. BR1005 will enter pairing mode automatically when powered on for
the first time.
b. BR1005 can only automatically re-pair to the 4 most recently
connected devices.
4
3) Turn on your first device and wait for 10 to 20 seconds. Both of your
devices are now ready for pairing. Turn on the BR1005, the devices
will automatically connect in.
Note:
a. Please turn off the BR1005 and restart it to re-pair if two devices
cannot play music at the same time. If the problem still exists after
repeating the whole steps above, please contact Inateck Support
at: support@inateck.com.
b. It is advised to switch off the Bluetooth function of your other
devices to avoid signal interference.
c. We have performed the compatibility testing with various Bluetooth
chipsets on the market. But please note not all these chipsets use
the same software, compatibility issue might still encounter for
some Bluetooth devices. Please contact our customer support team
for help.
d. BR1005 can automatically re-pair to the 2 most recently connected
devices.
5
LED Indicator
LED Indicator(RX Mode) Status
Blue LED flashes twice every 3 seconds Automatically Pairing with Previously Paired Devices
How to Use
1. Pairing
1) Set the BR1005 to RX mode before turning it on.
2) Turn on the BR1005 by pressing and holding the Multifunction
Button for 3 seconds. Rapidly tap the Multifunction Button twice
to enter pairing mode with the LED indicator flashes blue and red
alternately.
3) Activate the Bluetooth function on your transmitting device and
find "Inateck BR1005" to connect. The BR1005 LED indicator will
turn solid blue after successfully paired.
4) Connect the BR1005 to your headphone or home stereo playback
device through a 3.5mm audio or SPDIF OUT port to enjoy the
music.
Note:
a. If a PIN code is required for pairing, try 0000, 8888, 1111 or 1234.
b. This product has no built-in microphone which cannot be used for
hands-free calls.
c. BR1005 can remember 8 paired devices, when the number of paired
devices exceeds 8, the first one will be replaced.
6
3) Turn off the BR1005 after successfully pairing it with your second
device. Activate the Bluetooth function on your first device, turn on
the BR1005 after about 20 seconds. After approximately 30 seconds,
pairing will be completed.
Product Specifications
Bluetooth Version V4.1, Class Ⅱ
Dimensions 60*60*18.4mm
Package Contents
BR1005 × 1
3.5mm Audio Cable × 1
Optical Digital Cable × 1
3.5mm Female to RCA Male Cable × 1
Micro-B Charging Cable × 1
User Manual × 1
7
FAQ
1. BR1005 will not automatically re-pair to my devices after turning on
it. I am having trouble pairing and connecting to my devices after
turning on it.
Follow the previous instructions in the “Clear Pairing History”
section to clean the pairing list and reconnect.
2. BR1005 will not power on.
Plug BR1005 into a charger and see if the LED indicator turns red.
Please recharge it until the LED indicator turns off to make sure the
adapter has enough battery power. Please contact our customer
support team if you need further assistance.
3. After connecting with my Bluetooth device, I cannot hear any music
from my sound system.
Please check the following:
•Your sound system is connected to the adapter via the audio cable
or optical digital cable.
•Make sure the audio port of the BR1005 and the audio output
setting on your TV are matching. In TX mode, the audio output
mode on your TV would be digital audio if it is connected to the
BR1005 through the SPDIF port.
• Make sure the music volume is at an audible level on both your
Bluetooth device and sound system.
• For some systems, you may need to select “AUX” or “Line-in” as
the audio input mode.
• Some devices (such as computer) require manually selecting the
music output mode.
Support
If you need any further assistance regarding the Inateck BR1005
wireless adapter, please contact our customer support team at
support@inateck.com.
8
Deutsch
Übersicht
G
F
B
E
C
D
No. Bestandteile
A Multifunktionsknopf
G USB-Ladebuchse
H LED-Anzeige
9
Aufladen
Die LED-Anzeige blinkt rot, wenn ein niedriger Ladestand erreicht ist
und ein Aufladen notwendig ist.
1. Binden Sie den USB-Stecker des Ladekabels an einen freien aktiven
USB-Anschluss an (Netzteil, Ladegerät oder Rechner: Ladespannung
5 Volt). Verbinden Sie den Mikro-USB-Stecker des Kabels mit der
Ladebuchse am BR1005.
2. Die LED-Anzeige leuchtet während des Ladevorgangs permanent rot.
3. Die LED-Anzeige erlischt automatisch, wenn der Ladevorgang
abgeschlossen ist. Es dauert in der Regel 2,5 Stunden, um einen
vollständigen Ladevorgang abzuschließen.
Bitte beachten:
a. Bei Budget-Netzteilen könnte es zu Ladestörgeräuschen kommen,
da aufgrund subqualitativer Bauteile meist keine stabile Spannung
gewährleistet werden kann.
b. Um eine Tiefenentladung des Akkumulators zu vermeiden, wird
empfohlen, das Gerät mindestens einmal im Monat pro forma zu
laden. Lithium-Ionen-Akkumulatoren entladen sich allmählich auch
lagernd und wenn Sie nicht in Betrieb sind
Allgemeine Funktionen
1. An- und Ausschalten.
Halten Sie den Multifunktionsknopf für ca. drei Sekunden gedrückt.
Angeschaltet: die LED blinkt blau.
Ausgeschaltet: Die LED blinkt kurz rot und erlischt dann
automatisch.
2. Automatische Wiederkopplung mit bereits gespeicherten Geräten.
Das BR1005 geht automatisch in den Kopplungsmodus, sobald es
zum ersten Mal in Betrieb genommen wird. Außerdem merkt sich
das BR1005 die bereits vollzogenen Kopplungen und Verbindungen
und wird somit eine Wiederherstellung dieser Verbindungen in
chronologischer Reihenfolge versuchen, ohne noch einmal in den
Kopplungsmodus überzugehen.
3. Schnellaktivierung des Kopplungsmodus.
Drücken Sie den Multifunktionsknopf zweimal schnell
hintereinander, nachdem das BR1005 eingeschaltet wurde, um den
Kopplungsmodus zu erzwingen.
10
4. TX/RX-Modusschalter
Wechseln Sie den Modusschalter beim Ausschalten, um den
gewünschten Modus zu wählen.
TX/RX-Modi können nur gewechselt werden, nachdem das BR1005
mindestens für fünf Sekunden ausgeschaltet ist.
Tipp: Schalten Sie das BR1005 ab und nach fünf Sekunden wieder
ein, falls der Modusschalter nicht ordnungsgemäß funktioniert, um
eine Störung auszuschließen.
5. Kopplungseinträge löschen und Speicher leeren
Bitte beachten Sie folgende Arbeitsschritte, um bei
Kopplungsfehlern den Speicher zurückzusetzen:
1) Schalten Sie das BR1005 ab, wechseln den Modus TX(RX) nach
fünf Sekunden auf RX(TX).
2) Schalten Sie das BR1005 ab, wechseln den Modus RX(TX) nach
fünf Sekunden auf TX(RX).
Nach diesen Schritte werden die Kopplungseinträge von TX(RX)
Modus gelöscht werden.
6. AUX-/SPDIF-Modusschalter
Sie können beliebig zwischen SPDIF- und AUX-Modus hin- und
herwechseln. Im SPDIF-Modus können Geräte im TX-Modus über
den SPDIF-Eingang und im RX-Modus über den SPDIF-Ausgang
angebunden werden.
7. RX-Modus: Pause/Wiedergabe
Betätigen Sie den Multifunktionsknopf jeweils einmal kurz, um
abspielende Musik zu pausieren oder wiederzugeben.
8. Automatische Abschaltung
Im RX-Modus schaltet sich das BR1005 automatisch nach sechs
Minuten ab, wenn keine Kopplung erfolgt. Das BR1005 schaltet sich
im TX-Modus jedoch nicht automatisch ab.
Bluetooth-Sendemodus (TX)
Der Sendemodus ermöglicht es dem BR1005, Audiosignale von
kabelgebundenen Wiedergabegeräten ohne Bluetooth (TV, Rechner,
Stereoanlage) an Bluetooth-Kopfhörer oder Bluetooth-Lautsprecher
zu übermitteln. In diesem Modus werden die Wiedergabegeräte über
das Audiokabel mit dem BR1005 verbunden, während die Kopplung
mit den Kopfhörern oder Lautsprechern via Bluetooth geschieht.
11
LED-Anzeige
LED-Anzeige (TX-Modus) Status
Blaue LED blinkt alle drei Sekunden Automatische Wiederkopplung mit bereits
gespeicherten Geräten
12
Bitte beachten:
a. Das BR1005 geht bei der ersten Inbetriebnahme automatisch in den
Kopplungsmodus über.
b. Das BR1005 merkt sich bis zu vier der zuletzt gekoppelten Geräte
und versucht beim Einschalten, sich mit diesen automatisch wieder
zu verbinden.
13
Bluetooth-Empfangsmodus (RX)
Im RX-Modus können Sie via Bluetooth Musik über eigentlich
kabelgebundene Ausgabegeräte wie Kopfhörer oder Lautsprecher
wiedergeben, indem der Adapter mit diesen per Audio- oder
Optikkabel verbunden ist. Verbinden Sie das BR1005 mit den
Ausgabegeräten (Lautsprecher oder Kopfhörer), um dann eine
Kopplung mit Bluetooth-fähigen Wiedergabe- bzw. Stammgeräten
(Smartphone, Tablet o.ä.) zu vollziehen. So können Sie Klänge
an konventionelle Ausgabegeräte via Bluetooth übertragen und
vermeiden eventuell unnötiges Kabelgewirr.
LED-Anzeige
LED-Anzeige (RX-Modus) Status
LED blinkt alle drei Sekunden zweimal blau Automatische Wiederkopplung mit bereits
gespeicherten Geräten
14
3) Aktivieren Sie die Bluetooth-Suche auf Ihrem Stammgerät und
suchen Sie nach dem Eintrag „BR1005“. Tippen Sie auf den Eintrag,
um eine Verbindung herzustellen.
4) Verbinden Sie den Adapter nun mit einem Ausgabegerät via Klinke
oder optisches Audiokabel, um Ihre Musik genießen zu können.
Bitte beachten:
a. Wenn ein Kopplungscode verlangt wird, probieren Sie die
Ziffernfolgen „0000“, „8888“, „1111“ oder „1234“ aus.
b. Das BR1005 besitzt kein integriertes Mikrofon und ist somit auch
nicht für Freisprechtelefonate geeignet.
c. Das BR1005 kann sich im RX-Modus bis zu acht Geräteeinträge
merken. Wird diese Anzahl überschritten, so wird der älteste
Verbindungseintrag gelöscht.
15
Technische Daten
Bluetooth-Version V4.1, Class Ⅱ
Ladespannung 5V Gleichstrom
Ladestrom ≥300mA
Maße 60*60*18.4mm
Lieferumfang
Ein BR1005
Ein 3,5 mm Klinkenkabel
Ein optisches Audiokabel
Ein 3,5 mm Kabel (Klinkenbuchse auf RCA)
Ein Mikro-USB-Ladekabel
Eine Betriebsanleitung
16
2. Das BR1005 schaltet sich nicht ein.
Binden Sie das BR1005 über das Ladekabel an einen USB-Ausgang
an und überprüfen Sie, ob die LED rot leuchtet. Bitte laden Sie das
BR1005 nun so lange, bis die LED erlischt, um einen adäquaten
Ladestand zu gewährleisten. Wenn das Problem bestehen
bleibt, nehmen Sie bitte Kontakt zu uns auf, um im Rahmen der
Gewährleistung einen Defekt auzuschließen.
3. N a c h e r f o l g t e r K o p p l u n g w i r d k e i n e M u s i k ü b e r m e i n e
Ausgabegeräte wiedergegeben.
Bitte überprüfen Sie folgende Zustände:
• Ist das Wiedergabegerät per Audio- oder Optikkabel korrekt an
den Adapter angebunden?
• Stellen Sie sicher, dass Kabelanbindung an Wiedergabegerät und
Adapter übereinstimmen und kompatibel sind. Im TX-Modus
ist der Audiomodus des Wiedergabegeräts (zum Beispiel TV)
als „Digitales Audio“ ausgewiesen, wenn das Gerät via SPDIF-
Schnittstelle mit dem BR1005 verbunden ist.
• Überprüfen Sie, ob die Lautstärke an Wiedergabegerät und
Bluetooth-Ausgabegerät hoch genug ist, um wahrnehmbar zu
sein.
• Bei manchen Tonsystemen muss „AUX“ oder „Line Out“ als
Audio-Ausgang verwendet werden, um Töne an den BR1005 zu
übermitteln.
• Manche Geräte, zum Beispiel einige PCs, verlangen nach einer
manuellen Aktivierung des (Bluetooth-)Wiedergabemodus.
17
日本語
製品概要
G
F
B
E
C
D
No. Name
A 多機能ボダン
B TX /RX モード切り替えスイッチ(TX:トランスミッター RX:レシーバー)
D 3.5mm ステレオミニジャック
E 入力用光コネクタ(SPDIF IN)
F 出力用光コネクタ(SPDIF OUT)
G 電源コネクタ
H LED ランプ
18
充電
電力不足の場合赤色 LED ランプは高速点滅します。下記の手順に従
って本製品を充電してください。
1. 本製品の電源コネクタに付属の USB 電源ケーブルを接続する
2. USB 電源ケーブルを AC アダプタに接続する
3. USB AC アダプタを AC コンセントに差し込みます。(電源が入ると、
赤色 LED ランプが点灯します。充電が完了すると LED ランプは自
動的に消灯します。)
ご注意 :
充電しながら本製品を使用すると、ノイズが入る恐れがあります。
基本操作
1. 電源オン / オフ
多機能ボダンを 3 秒間に長押してください。
電源オン:青色 LED ランプは点滅する
電源オフ:赤色 LED ランプは点滅してから消灯する
2. 既にペアリング済みの機器と自動的に再接続する
既にペアリング済の機器の場合は、LED ランプが点灯した時点で自
動的に再接続します。
3. ペアリングモードに入る方法
電源オンの状態に多機能ボタンをダブルクリックしてから、ペアリ
ングモードに入ります。
4. TX/RX モードの切り替え
電源オフの状態に TX/RX モード切り替えスイッチを使って、TX モ
ードと RX モードを手軽に切り替えられます。必ず電源オフ後 5 秒
以上を経ってから、モードを切り替えてください。
ご注意 : 切替エラーが発生する場合は、本製品の電源をオフにして
から 5 秒後に再起動してください。
5. ペアリング履歴を削除する
Bluetooth 搭載機器とペアリングできない場合は、下記の手順に従
って本製品のペアリング履歴を削除してからもう一度やり直してく
ださい。
19
* TX モードにペアリング履歴を削除する方法
1) 電源をオフします。
2) 5 秒間以上をお待ちしてから RX モードに切り替えて、電源をオ
ンにしてください。そして電源をオフにしてください。
3) それから 5 秒後に、TX モードに戻って電源をオンにしてください。
* RX モードにペアリング履歴を削除する方法
1) 電源をオフします。
2) 5 秒間以上をお待ちしてから TX モードに切り替えて、電源をオ
ンにしてください。そして電源をオフにしてください。
3) それから 5 秒後に、RX モードに戻って電源をオンにしてください。
6. AUX/SPDIF モードを切り替える
AUX/SPDIF 切り替えスイッチを使って、AUX モードと SPDIF モー
ドを手軽に切り替えられます。SPDIF モードでは BR1005 をトラン
スミッター(TX モード)として使う場合は、SPDIF IN 端子経由に
てデバイスを接続してください。BR1005 をレシーバー(RX モード)
として使う場合は、SPDIF OUT 端子経由にてデバイスを接続してく
ださい。
7. RX モードに一時停止 / 再生
音声を再生中に多機能ボタンを押すと、一時停止となります。再び
押すと、再生を再開します。
8. オートパワーオフ
RX モード : ペアリングモードで接続可能デバイスを 6 分以内に見
つからないと、本製品はオートパワーオフします。
TX モード : オートパワーオフになりません。
20
LED ランプの見方
LED ランプの状態 本製品の状態
21
2. 2 台デバイスと同時にペアリングの方法
TX モードで本製品は 2 台の Bluetooth オーディオデバイスと同時に
ペアリングできます。
1) 上記のペアリング手順に従って、1 台目のデバイスとベアリングし
てください。そして、1 台目のデバイスの電源をオフにしてください。
2) 多機能ボタンをダブルクリックして、青色 LED が高速点滅して再
びペアリングモードに入ります。そして、2 台目のデバイスと接続
してから本製品の電源をオフにしてください。
3) 1 台目のデバイスを電源オンにして、約 20 秒ぐらいお待ちください。
そして本製品の電源をオンにして、2 台のデバイスとペアリング完
了までお待ちください。
ご注意 :
a. ペアリングが完了した後、音声が聞こえない場合は本製品をリスタ
ートしてみてください。もし問題が続けると上記の手順に従っても
う一度やり直してください。または、support@inateck.com まで
ご連絡ください。
b. 意図しない機器と接続されてしまう可能性がありますので、ペアリ
ングを実施する際に他の Bluetooth デバイスの電源をオフにしてく
ださい。
c. 特定の Bluetooth デバイスと接続する時に、相性問題が出る可能性
があります。この場合は、support@inateck.com までご連絡くだ
さい。
22
LED ランプの見方
LED ランプの状態 本製品の状態
How to Use
1. 1 台デバイスとペアリングの方法
1) 電源オフの状態で RX モードに切り替えてください。多機能ボタン
を 3 秒押して、電源がオンになります。赤色 LED と青色 LED が交
替に点滅し、自動的にペアリングモードに入ります。
2) ぺアリングしたい機器から本製品を検索します。本製品が見つかる
と,デバイス名「Inateck BR1005」が検索画面上に表示されます。
画面上のデバイス名をタップします。本製品の LED ランプが点滅
から点灯に変わると、ペアリングの完了です。
3) AUX モードまたは SPDIF モードを選択して、3.5mm オーディオケ
ーブルまたは光ケーブルを介して、本製品とイヤホン、スピーカー
などオーディオデバイスを接続してください。
ご注意 :
a. PIN コードが入力必要な場合は、0000、8888、1111、または 1234
を試してください。
b. 本製品は内蔵マイクがありません。通話機能に対応できかねます。
c. RX モードにペアリング情報は 8 台まで記憶できます。9台目を登
録した場合は、古い情報から順番に削除されます。削除された機器
と再接続する場合は、再度ペアリングが必要です。
2. 2 台デバイスと同時にペアリングの方法
RX モードに本製品は 2 台のデバイス(スマートフォン、タブレット
など)と同時に接続できます。下記の手順に従って操作してください。
* 2 台のデバイスの音声を同時に再生できかねます。例えば A 機器で
音声を再生中に、B 機器で音声を再生したい場合は、まず A 機器の音
声を一時停止必要です。
1) 上記のペアリング手順に従って、本製品を 1 台目のデバイスとペア
リングしてください。その後 1 台目のデバイスの Bluetooth 機能を
一時オフにしてください。そして、多機能ボタンをダブルクリック
してから本製品は再びペアリングモードに入ります。
23
2) 2 台目のデバイスとペアリングしてください。その後本製品の電源
をオフにしてください。そして、1 台目のデバイスの Bluetooth 機
能をオンにしてから 20 秒ぐらいお待ちください。本製品の電源を
オンにしてから自動的に 2 台のデバイスとペアリングします。ペア
リング完了まで約 30 秒ぐらい掛かります。
基本仕様
Bluetooth 仕様 V4.1, Class Ⅱ
最大使用時間 (AUX) 約 20 時間
最大使用時間 (SPDIF) 約 16 時間
充電時間 2.5 時間
入力電圧 DC5V
入力電流 ≥300mA
重量 Approx. 40.6g
外形寸法 60*60*18.4mm
パッケージ
BR1005 × 1
3.5MM オーディオケーブル × 1
光ケーブル × 1
RCA ケーブル × 1
Micro-B USB 充電ケーブル × 1
取扱説明書 × 1
24
FAQ
1. Bluetooth 搭載機器とペアリングできない
• 意図しない機器と接続されてしまう場合は、その機器の電源を切
ってからやり直してください。
・「三、基本操作>ペアリング履歴を削除する」に記載する手順
により、本製品のペアリング履歴を削除してからやり直してくだ
さい。
2. 本製品は起動できない
赤色 LED ランプを消灯まで充電してください。フル充電されても
問題が続けると Inateck カスタマーサポートまでご連絡ください。
3. 音声が聞こえない(Bluetooth 接続)
下記のことはご確認ください :
• すべてのケーブルはしっかり接続したのでしょうか。
• TX モードに本製品は光ケーブルでテレビと接続する場合、テレ
ビの音声出力設定がデジタルオーディオ出力(デジタル音声出力)
に設定してください。
• お使いデバイスはマナーモードに設定されたことはないでしょう
か。
• 一部のシステムでは、「AUX」または「Line-in」とのオーディオ
入力モードを選択する必要があります。
• 一部のデバイス(コンピュータなど)では、音楽出力モードを手
動で選択する必要があります。
サポート
当社の製品に関するお問い合わせやコメントがおありでしたら、
support@inateck.com までご連絡ください。御連絡を承り次第ご 対
応いたします。
25
Contact Information
USA
Tel.: +1 513-644-9712
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: support@inateck.com
Web: www.inateck.com
Addr.: F&M Technology LLC, 9852 Crescent Park Drive,
West Chester, OH 45069 USA
Japan
Email: support@inateck.com
Web: www.inateck.com/jp/
Addr.: F&M株式会社 東京都昭島市拝島町三丁目10番3号