SikaFast®-5211 NT Fast curing, two-part structural adhesive
Technical Product Data
Component A Component B Properties ® ® SikaFast -5211 NT SikaFast -5200 Chemical base Acrylate 1 Colour (CQP 001-1) White Black Colour mixed Grey Curing mechanism Radical polymerisation Density (CQP 006-4) 1.15 kg/l approx. 1.5 kg/l approx. Density mixed (calculated) 1.19 kg/l approx. Mixing ratio by volume 10 : 1 by weight 10 : 1.3 Consistency Thixotropic paste Application temperature 5 - 40°C Open time2 (CQP 526-2) 3 min approx. Fixture time2 time to reach 80% of final strength 9 min approx. Shore A hardness (CQP 023-1 / ISO 868) 90 approx. Shore D hardness (CQP 023-1 / ISO 868) 50 approx. Tensile strength2 (CQP 036-1 / ISO 37) 10 MPa approx. Elongation at break2 (CQP 036-1 / ISO 37) 200% approx. E-Modulus2 (CQP 036-1 / ISO 37) 250 MPa approx. Tensile Lap-Shear Strength2 (CQP 046-6 / ISO 4587) 10 MPa approx. Glass transition temperature (CQP 509-1 / ISO 6721-2) 60°C approx. Service temperature -40 - 80°C 3 Shelf life (CQP 016-1) 9 months 1) 2) 3) CQP = Corporate Quality Procedures 23°C / 50% r.h. Stored at temperature below 25°C and not exposed to direct sun light
Description Product Benefits Areas of Application
® ® SikaFast -5211 NT is a fast curing, - Strength development within SikaFast -5211 NT is a fast curing, flexibilised structural, two-part minutes after application flexibilised structural adhesive adhesive system, which is based - Adhesion to a wide range of designed to replace mechanical on Sika’s Acrylic Double Perfor- substrates without or with limited fixings such as rivets, screws or mance (ADP) polymer technology. surface preparation welding. It is suitable for high Uncured SikaFast®-5211 NT is a - High strength and impact re- strength fastening of concealed pasty, non-sagging, hardly inflam- sistance joints and exhibits excellent adhe- mable material which allows an - Solvent and acid free sion on different types of sub- easy and precise application. - Lower odour than MMA contain- strates including top coats, plas- SikaFast®-5211 NT is manu- ing products tics, glass, wood, etc. factured in accordance with ISO - Easy mixing This product is recommended for 9001 / 14001 quality assurance professional experienced users system and the responsible care only. Tests with actual substrates program. and conditions have to be per- formed to ensure adhesion and material compatibility. SikaFast -5211 NT 1 / 2 ® Cure Mechanism Application Packaging Information ® SikaFast -5211 NT cures accord- SikaFast®-5211 NT is applied with Dual cartridge 250 ml ing to radical chain polymerisation a mixing ratio of 10 : 1 (± 10%) by when mixed with SikaFast®-5200. volume through a 24 elements static mixer. Value Bases Open and fixture time are influ- enced by mixing ratio deviations as Consider that if applied in large All technical data stated in this well as temperature, e.g. as higher masses, heat is generated by the Product Data Sheet are based on the temperature as shorter the exothermic reaction. To avoid laboratory tests. Actual measured open and fixture time and vice excessive temperature increase, data may vary due to circum- versa. bond line thickness is limited to 3 stances beyond our control. mm, but must measure at least 0.5 Chemical Resistance mm. The mixed adhesive has an Health and Safety Information ® SikaFast -5211 NT is resistant to open time of approx. 3 minutes For information and advice re- many chemicals. For specific in- and achieves handling strength garding transportation, handling, formation, contact the Technical (fixture time) in approx. 9 minutes. storage and disposal of chemical Department of Sika Industry. Optimum temperature for the products, users shall refer to the bonding process is between 15°C actual Safety Data Sheets contain- and 25°C. The approved tempera- ing physical, ecological, toxicologi- Adhesion results ture range for substrates and ad- cal and other safety related data. The following table summarises hesive is between 5°C and 40°C. lap-shear test results obtained with The influence of the reactivity by Legal Notes different standard substrates. The- temperature changes has to be The information, and, in particular, the se results are indications only. Due respected. recommendations relating to the appli- to the diversity of substrates, pre- After the open time has elapsed cation and end-use of Sika products, liminary tests are mandatory. the bonded parts must not be are given in good faith based on Sika's moved against each other any- current knowledge and experience of Adhesion table (typical values) the products when properly stored, more. When the fixture time is Material FM 1 Value handled and applied under normal reached the parts can be moved if conditions in accordance with Sika's AlMg3 C 10 MPa no additional stress is distributed to recommendations. In practice, the Stainless steel C 10 MPa the bond line. differences in materials, substrates and El. galv. steel C 10 MPa For additional information and actual site conditions are such that no support in evaluation of the appro- warranty in respect of merchantability Glass C/A 8 MPa or of fitness for a particular purpose, priate application equipment con- ABS A 7 MPa tact the Sika System Engineering nor any liability arising out of any legal PVC C/S 10 MPa relationship whatsoever, can be in- department of Sika Industry. ferred either from this information, or PC A 9 MPa Removal from any written recommendations, or Table 1: Lap shear samples according to ISO Uncured excess of SikaFast®-5211 NT from any other advice offered. The user 4587 bond line thickness 1.5 mm of the product must test the product’s 1 can be removed easily before suitability for the intended application Failure mode: Adhesive, Cohesive, Substrate curing with a dry wipe, with Sika® and purpose. Sika reserves the right to Remover-208 or another suitable change the properties of its products. Method of application solvent. Once the adhesive is The proprietary rights of third parties Substrate preparation cured it can only be removed me- must be observed. All orders are ac- Surfaces must be clean, dry and chanically. cepted subject to our current terms of free from grease, oil and dust. Hands and exposed skin should be sale and delivery. Users must always Remove all loose particles or resi- washed immediately using Sika® refer to the most recent issue of the dues by cleaning it thoroughly. For Handclean towels or a suitable local Product Data Sheet for the prod- best adhesion performance pre- uct concerned, copies of which will be ® industrial hand cleaner and water. supplied on request. treat the bonding area with Sika Do not use solvents! ADPrep prior to the bonding pro- cess. Due to the diversity of mate- rials, preliminary tests with original Further Information substrates are necessary. Copies of the following publications are available on request: Advice on specific applications is available from the Technical De- - Safety Data Sheet partment of Sika Industry. - General Guidelines Bonding with SikaFast® adhe- sives SikaFast -5211 NT 2 / 2 ®