Sei sulla pagina 1di 223

LECTURE NOTES

ON

ELECTRONIC DEVICES AND CIRCUITS

B.Tech IIIsemester
(Common for ECE/EEE)

Dr. P.Ashok Babu, Professor


Mr. V R Seshagiri Rao, Professor
Mr. K.Sudhakar Reddy, AssosciateProfessor
Mr. B.Naresh, AssosciateProfessor

ELECTRONICS AND COMMUNICATION ENGINEERING

INSTITUTE OF AERONAUTICAL ENGINEERING


(Autonomous)
DUNDIGAL, HYDERABAD - 500043
ELECTRONIC DEVICES AND CIRCUITS

III Semester: ECE

Course Code Category Hours / Week Credits Maximum Marks


L T P C CIA SEE Total
AEC001 Foundation
3 1 - 4 30 70 100
Contact Classes: 45 Tutorial Classes: 15 Practical Classes: Nil Total Classes: 60
OBJECTIVES:
The course should enable the students to:
1. Be acquainted with electrical characteristics of ideal and practical diodes under forward and reverse
bias to analyze and design diode application circuits such as rectifiers and voltage regulators.
2. Utilize operational principles of bipolar junction transistors and field effect transistors to derive
appropriate small-signal models and use them for the analysis of basic amplifier circuits.
3. Perform DC analysis (algebraically and graphically using current voltage curves with super
imposed load line) and design of CB,CE and CC transistor circuits.
4. IV. Compare and contrast different biasing and compensation techniques

UNIT-I SEMICONDUCTOR DIODES Classes: 08


PN Junction Diode : Theory of PN diode, energy band diagram of PN diode, PN junction as a diode,
operation and V-I characteristics , static and dynamic resistances, diode equivalent circuits, diffusion
and transition capacitance, diode current equation, temperature dependence of V-I characteristics,
Zener diode characteristics ,break down mechanisms in semiconductor diodes, Zener diode as a
voltageregulator.

UNIT-II SPECIAL PURPOSE ELECTRONIC DEVICES AND RECTIFIERS Classes: 10

Special purpose electronic devices: principles of operation and characteristics of silicon controlled
rectifier, tunnel diode, varactor diode, photodiode; Half wave rectifier, full wave rectifier, general filter
consideration, harmonic components in a rectifier circuit , Inductor Filter, capacitor filter, L-Section
filter, multiple L-C section, RC filter, comparison of filters.

UNIT-III TRANSISTORS Classes: 08


Bipolar Junction Transistors: Construction of BJT, operation of BJT, minority carrier distributions and
current components, configurations, characteristics, BJT specifications; Applications: Amplifier,switch.

Field Effect Transistors: Types of FET, FET construction, symbol, principle of operation, V-I
characteristics, FET parameters, FET as voltage variable resistor, comparison of BJT and FET;
MOSFET construction and operation; Uni-Junction Transistor: Symbol, principle of operation,
characteristics, applications (UJT as relaxation oscillator).

UNIT-IV BIASING AND COMPENSATION TECHNIQUES Classes: 10

Need for biasing, BJT operating point, The DC and AC load lines, types of biasing circuits, bias
stability, stabilization factors, stabilization against variations in VBE and β; Bias compensation
techniques, thermal runaway, thermal stability, biasing the FET and MOSFET.
Classes: 09
UNIT-V BJT AND FET AMPLIFIERS
BJT small signal analysis, BJT hybrid model, determination of h-parameters from transistor
characteristics, transistor amplifiers analysis using h- parameters; F ET small signal model, FET as
common source amplifier, FET as common drain amplifier, FE T as common gate amplifier,
generalized FET amplifier .

Text Books:
nd
1. J. Millman, C.C.Halkias, “Millman‘s Integrated Electronics”, Tata McGraw-Hill, 2 Edition, 2001.
2. J. Millman, C.C.Halkias, Satyabrata Jit, ―Millman‘s Electronic Devices and Circuits‖, Tata
nd
McGrawHill, 2 Edition, 1998.
th
3. David A. Bell, ―Electronic Devices and Circuits‖, Oxford University Press ,5 Edition,2008.

Reference Books:
st
1. Sedha.R.S, “A Text Book of Applied Electronics‖, Sultan Chand Publishers”,1 Edition, 2008
th
2. R L. Boylestad, Louis Nashelsky, “Electronic Devices and Circuits‖, PEI/PHI”, 9 edition,
2006.Gupta.J.B,
nd
3. “Electron Devices and Circuits‖, S.K.Kataria & Sons”, 2 Edition,2012. Salivahanan, N. Suresh
Kumar,A. Vallavaraj.

Web References:

Hhttp://wwwmdp.eng.cam.ac.uk/web/library/enginfo/electrical/hong1.pd
https://archive.org/details/ElectronicDevicesCircuits http://nptel.ac.in/courses/Webcourse-contents/
http://www.satishkashyap.com/2013/03/video-lectures-on-electron-devices-by.html

E-Text Books:

http://services.eng.uts.edu.au/pmcl/ec/Downloads/LectureNotes.pdf
http://nptel.ac.in/courses/122106025/
http://www.freebookcentre.net/electronics-ebooks-download/Electronic-Devices-and-Circuits-
(PDF-313p).html
https://www.jntubook.com/electronic-device-circuits-textbook-free-
download/http://www.faadooengineers.com/threads/32735-Electronic-Devices-And-Circuits-
(EDC)-by- J-B-Gupta-full-book-pdf
1

UNIT 1
PN JUNCTION DIODE
INTRODUCTON
Based on the electrical conductivity all the materials in nature are classified as insulators, semiconductors,
and conductors.

Insulator: An insulator is a material that offers a very low level (or negligible) of conductivity when
voltage is applied. Eg: Paper, Mica, glass, quartz. Typical resistivity level of an insulator is of the order of
1010 to 1012 Ω-cm. The energy band structure of an insulator is shown in the fig.1.1. Band structure of a
material defines the band of energy levels that an electron can occupy. Valance band is the range of
electron energy where the electron remain bended too the atom and do not contribute to the electric
current. Conduction bend is the range of electron energies higher than valance band where electrons are
free to accelerate under the influence of external voltage source resulting in the flow of charge.
The energy band between the valance band and conduction band is called as forbidden band gap.
It is the energy required by an electron to move from balance band to conduction band i.e. the energy
required for a valance electron to become a free electron.
1 eV = 1.6 x 10-19 J
For an insulator, as shown in the fig.1.1 there is a large forbidden band gap of greater than 5Ev. Because
of this large gap there a very few electrons in the CB and hence the conductivity of insulator is poor. Even
an increase in temperature or applied electric field is insufficient to transfer electrons from VB to CB.
2

CB
CB CB

o
Forbidden band Eo =≈6eV
gap Eo ≈6eV

VB
VB
VB

Insulator Semiconductor Conductor

FiG:1.1 Energy band diagrams insulator, semiconductor and conductor

Conductors: A conductor is a material which supports a generous flow of charge when a voltage
is applied across its terminals. i.e. it has very high conductivity. Eg: Copper, Aluminum, Silver,
Gold. The resistivity of a conductor is in the order of 10-4 and 10-6 Ω-cm. The Valance and
conduction bands overlap (fig1.1) and there is no energy gap for the electrons to move from
valance band to conduction band. This implies that there are free electrons in CB even at
absolute zero temperature (0K). Therefore at room temperature when electric field is applied
large current flows through the conductor.

Semiconductor: A semiconductor is a material that has its conductivity somewhere between the
insulator and conductor. The resistivity level is in the range of 10 and 104 Ω-cm. Two of the most
commonly used are Silicon (Si=14 atomic no.) and germanium (Ge=32 atomic no.). Both have 4
valance electrons. The forbidden band gap is in the order of 1eV. For eg., the band gap energy
for Si, Ge and GaAs is 1.21, 0.785 and 1.42 eV, respectively at absolute zero temperature (0K).
At 0K and at low temperatures, the valance band electrons do not have sufficient energy to move
from V to CB. Thus semiconductors act a insulators at 0K. as the temperature increases, a large
number of valance electrons acquire sufficient energy to leave the VB, cross the forbidden
bandgap and reach CB. These are now free electrons as they can move freely under the influence
of electric field. At room temperature there are sufficient electrons in the CB and hence the
semiconductor is capable of conducting some current at roomtemperature.
Inversely related to the conductivity of a material is its resistance to the flow of charge or
current. Typical resistivity values for various materials’ are given as follows.
3

Insulator Semiconductor Conductor


10-6 Ω-cm (Cu) 50Ω-cm (Ge) 1012 Ω-cm
(mica)

50x103 Ω-cm (Si)

Typical resistivity values

SemiconductorTypes

A pure form of semiconductors is called as intrinsic semiconductor. Conduction in intrinsic sc is


either due to thermal excitation or crystal defects. Si and Ge are the two most important semiconductors
used. Other examples include Gallium arsenide GaAs, Indium Antimonide (InSb) etc.

Let us consider the structure of Si.A Si atomic no. is 14 and it has 4 valance electrons. These 4
electrons are shared by four neighboring atoms in the crystal structure by means of covalent bond. Fig.
1.2a shows the crystal structure of Si at absolute zero temperature (0K). Hence a pure SC acts has poor
conductivity (due to lack of free electrons) at low or absolute zero temperature.

Covalent bond

Valence electron

Fig. 1.2a crystal structure of Si at 0K


4

At room temperature some of the covalent bonds break up to thermal energy as shown in
fig 1.2b. The valance electrons that jump into conduction band are called as free electrons that
are available forconduction.

Free electron

Valance electron

hole

Fig. 1.2b crystal structure of Si at room


temperature0K

The absence of electrons in covalent bond is represented by a small circle usually


referred to as hole which is of positive charge. Even a hole serves as carrier of electricity in a
manner similar to that of freeelectron.

The mechanism by which a hole contributes to conductivity is explained as follows:

When a bond is in complete so that a hole exists, it is relatively easy for a valance
electron in the neighboring atom to leave its covalent bond to fill this hole. An electron moving
from a bond to fill a hole moves in a direction opposite to that of the electron. This hole, in its
new position may now be filled by an electron from another covalent bond and the hole will
correspondingly move one more step in the direction opposite to the motion of electron. Here we
have a mechanism for conduction of electricity which does not involve free electrons. This
phenomenon is illustrated infig1.3
5

Electron movement

Hole movement

Fig. 1.3a

Fig. 1.3b

Fig. 1.3c
6

Fig 1.3a show that there is a hole at ion 6.Imagine that an electron from ion 5 moves into
the hole at ion 6 so that the configuration of 1.3b results. If we compare both fig1.3a &fig 1.3b, it
appears as if the hole has moved towards the left from ion6 to ion 5. Further if we compare fig
1.3b and fig 1.3c, the hole moves from ion5 to ion 4. This discussion indicates the motion of
hole is in a direction opposite to that of motion of electron. Hence we consider holes as physical
entities whose movement constitutes flow ofcurrent.

In a pure semiconductor, the number of holes is equal to the number of free electrons.

EXTRINSICSEMICONDUCTOR:
Intrinsic semiconductor has very limited applications as they conduct very small amounts
of current at room temperature. The current conduction capability of intrinsic semiconductor can
be increased significantly by adding a small amounts impurity to the intrinsic semiconductor. By
adding impurities it becomes impure or extrinsic semiconductor. This process of adding
impurities is called as doping. The amount of impurity added is 1 part in 106 atoms.

N type semiconductor: If the added impurity is a pentavalent atom then the resultant
semiconductor is called N-type semiconductor. Examples of pentavalent impurities are
Phosphorus, Arsenic, Bismuth, Antimony etc.

A pentavalent impurity has five valance electrons. Fig 1.3a shows the crystal structure of N-
type semiconductor material where four out of five valance electrons of the impurity
atom(antimony) forms covalent bond with the four intrinsic semiconductor atoms. The fifth
electron is loosely bound to the impurity atom. This loosely bound electron can be easily

Fifth valance electron of SB

CB
Ec
Ed
Donor energy level
Ev
VB

Fig. 1.3a crystal structure of NtypeSC Fig. 1.3bEnergy band diagram of Ntype
7

excited from the valance band to the conduction band by the application of electric field or
increasing the thermal energy. The energy required to detach the fifth electron form the impurity
atom is very small of the order of 0.01ev for Ge and 0.05 eV for Si.

The effect of doping creates a discrete energy level called donor energy level in the forbidden
band gap with energy level Ed slightly less than the conduction band (fig 1.3b). The difference
between the energy levels of the conducting band and the donor energy level is the energy
required to free the fifth valance electron (0.01 eV for Ge and 0.05 eV for Si). At room
temperature almost all the fifth electrons from the donor impurity atom are raised to conduction
band and hence the number of electrons in the conduction band increases significantly. Thus
every antimony atom contributes to one conduction electron without creating a hole.

In the N-type sc the no. of electrons increases and the no. of holes decreases compared to
those available in an intrinsic sc. The reason for decrease in the no. of holes is that the larger no.
of electrons present increases the recombination of electrons with holes. Thus current in N type
sc is dominated by electrons which are referred to as majority carriers. Holes are the minority
carriers in N typesc

P type semiconductor: If the added impurity is a trivalent atom then the resultant semiconductor
is called P-type semiconductor. Examples of trivalent impurities are Boron, Gallium , indium etc.

The crystal structure of p type sc is shown in the fig1.3c. The three valance electrons of the
impurity (boon) forms three covalent bonds with the neighboring atoms and a vacancy exists in
the fourth bond giving rise to the holes. The hole is ready to accept an electron from the
neighboring atoms. Each trivalent atom contributes to one hole generation and thus introduces a
large no. of holes in the valance band. At the same time the no. electrons are decreased compared
to those available in intrinsic sc because of increased recombination due to creation of additional
holes.

hole

Fig. 1.3c crystal structure of P type sc


8

Thus in P type sc , holes are majority carriers and electrons are minority carriers. Since
each trivalent impurity atoms are capable accepting an electron, these are called as acceptor
atoms. The following fig 1.3d shows the pictorial representation of P type sc

hole (majority carrier)

Electron (minority carrier)

Acceptor atoms

Fig. 1.3d crystal structure of P type sc

 The conductivity of N type sc is greater than that of P type sc as the mobility of


electron is greater than that ofhole.

 For the same level of doping in N type sc and P type sc, the conductivity of anNtype
sc is around twice that of a P typesc

CONDUCTIVITY OFSEMICONDUCTOR:
In a pure sc, the no. of holes is equal to the no. of electrons. Thermal agitation continue to
produce new electron- hole pairs and the electron hole pairs disappear because of recombination.
with each electron hole pair created , two charge carrying particles are formed . One is negative
which is a free electron with mobility µ n . The other is a positive i.e., hole with mobility µ p . The
electrons and hole move in opppsitte direction in a an electric field E, but since they are of
opposite sign, the current due to each is in the same direction. Hence the total current density J
within the intrinsic sc is given by

J = Jn + Jp

=q n µn E + q p µp E

= (n µn + p µp)qE

=σ E

Where n=no. of electrons / unit volume i.e., concentration of free electrons

P= no. of holes / unit volume i.e., concentration of holes

E=applied electric field strength, V/m

q= charge of electron or hole I n Coulombs


9

Hence, σ is the conductivity of sc which is equal to (n µ n + p µp)q. he resistivity of sc is


reciprocal of conductivity.

Ρ = 1/ σ

It is evident from the above equation that current density with in a sc is directly
proportional to applied electric field E.

For pure sc, n=p= ni where ni = intrinsic concentration. The value of ni is given by

ni 2=AT3 exp (-EGO/KT)

therefore, J= ni ( µn + µp) qE

Hence conductivity in intrinsic sc is σi= ni ( µn + µp) q

Intrinsic conductivity increases at the rate of 5% per o C for Ge and 7% per o C for Si.

Conductivity in extrinsic sc (N Type and P Type):

The conductivity of intrinsic sc is given by σi= ni ( µn + µp) q = (n µn + p µp)q

For N type , n>>p

Therefore σ= q n µn

For P type ,p>>n

The energy band diagram of p-n junction under open circuitconditions

( Expression for pn junction diode barrier potential. )

 It is known that the Fermi level in n-type material lies just below the conduction band while in
p-type material, it lies just above the valenceband.
 When p-n junction is formed, the diffusion starts. The changes get adjusted so as toequalize
the Fermi level in the two parts of p-njunction.
 This is similar to adjustment of water levels in two tanks of unequal level, when connected
eachother.
 The changes flow from p to n and n to p side till, the Fermi level on two sides get linedup.
 In n-type semi conductor , EF is close to conduction band Ecn and it is close to valence band
edge EVP onp-side.
 So the conduction band edge of n-type semiconductor can‟t be at the same level as that of p-
type semiconductor.
10

 Hence, as shown, the energy band diagram for p-n junction is where a shift in energy levels E0
isindicated.
11
12

1.0..5 Doide current equation


• When a forward bias (VA>0) is applied, the potential barrier to diffusion across the
junction isreduced

– Minority carriers are “injected” into the quasi-neutral regions =>Dnp> 0, Dpn>0

• Minority carriers diffuse in the quasi-neutral regions, recombining with majoritycarriers

• Solve minority-carrier diffusion equations in quasi-neutral regions to obtain excess


carrier distributionsDnp(x,VA),Dpn(x,VA)
13

– boundaryconditions:
• p side: Dnp(-xp),Dnp(-)
• n side: Dpn(xn),Dpn()
• Find minority-carrier current densities in quasi-neutral regionsEvaluate Jn at x=-xp&Jp
at x=xn to obtain total current density J
J (VA ) Jn (xp ,VA ) J p (xn ,VA )

Consider the equilibrium (VA = 0) carrier concentrations:

Consider the equilibrium (VA = 0) carrier concentrations:


p side n side

p p 0 (x p ) N A nn0 (xn ) N D


n2 i n2
n p0 (x p )  pn0 (xn ) i
NA ND
If low-level injection conditions hold in the quasi-neutral regions
when VA 0, then
pp (xp ) NA nn (xn ) ND
14

The voltage applied to a pn junction falls mostly across the depletion


region (assuming low-level injection in the quasi-neutral regions).
We can draw 2 quasi-Fermi levels in the depletion region:

p n ie( Ei FP )/ kT
n n ie( FN Ei )/ kT

pn n2i e( F N FP )/ kT

pn n i2eqV / AkT

Excess Carrier Concentrations at –xp, xn


p side n side

pp (xp ) NA nn (xn ) ND


n 2 e q V /kT
A
n 2 e q V /kT
A

np (xp )  i pn (x n ) i
NA ND
n p0 e q V /kT A
pe
n0
q V /kTA

2

np (xp ) ni qV / kT e A 1  n2
pn (xn ) ie N D  qVA / kT
1 
NA
15




Excess Carrier Distribution (n side)


d 2p pn pn
• From the minority carrier diffusionequation: n 
dx2  D  L2
p p p

• We have the following boundary conditions:


p (x ) p (e qV /kT1)A p ()  0
n n no n

• For simplicity, use a new coordinatesystem:


NEW: x’’ 0 0 x’

x'/ Lp
p (x') Ae A e
x'/ Lp
• Then, the solution is of theform:
n 1 2

x'/ Lp
p (x')Ae A e
x '/ Lp

n 1 2

Fromthex=boundarycondition:

Fromthex=xnboundarycondition:

x'/Lp
Therefore pn (x') pno (eqVA/kT 1)e , x' 0

Similarly, we can derive


n(x'')n
p po
(e qVA/kT 1)ex''/Ln , x'' 0
16

Total Current Density


J qD dnp (x'') Dn
p side:
n n q n p0 (e qVAkT1)e x ''Ln
dx'' Ln
dpn (x') Dp qVkT x' Lp
n side: J p qDp q pn0 (e A
1)e
dx' Lp

J Jn xx J p xx Jn x0 J p x0


p n

Jqn2 i LNDn Dp  qV kT  1)


L N  (e A

n A p D



Ideal Diode Equation

II(e
0
qVAkT
1)
 Dp 2 Dn 
I0 Aqni  N 
 

L p D
Ln N A 
17

Diode Saturation Current I0


• I0 can vary by orders of magnitude,depending on the
semiconductor material and dopant concentrations:
 Dp  Dn
I0 Aqn2i  

L N


 p D Ln N A

• In an asymmetrically doped (one-sided) pn junction, theterm


associated with the more heavily doped side is negligible:
– If the p side is much more heavily doped, I 0 Aqni 2
 D  
L Np 
 p D 
2 Dn 
 – If the n side is much more heavily doped, I Aqn 
0 i  
LN
n A

Carrier Concentration Profiles


under ReverseBias

• Depletion of minority carriers at edges of depletionregion


• The only current which flows is due to drift of minority carriers
across the junction. This current is fed by diffusion of minority
carriers toward junction (supplied by thermalgeneration).
18

Alternative Derivation of Formula for I0


“Depletion approximation”:
• I0 is the rate at which carriers
are thermally generated within
one diffusion length of the
depletionregion:
n np  ni / N A
2
  -LN -xp x -xp
t n n
p p 2
n /N
ni D xn x xn LP
p p
t
i n 2 / NA
  2 
i n / N D
I 0 qALN  qALP 
 
 n   p 





• Under forward bias (VA > 0), the potential barrier to carrier
diffusionisreducedminoritycarriersare“injected”intothe
quasi-neutralregions.
– The minority-carrier concentrations at the edges of the depletionregion
change with the applied bias V A, by the factor e q VA /kT
– The excess carrier concentrations in the quasi-neutral regions decay to
zero away from the depletion region, due torecombination.

IqAn2 i LNDn Dp (e qV kT1)


A

pn junction diodecurrent LN 


n A p D

• I0canbeviewedasthedriftcurrentduetominoritycarriers
generatedwithinadiffusionlengthofthedepletionregion

QUANTITATIVE THEORY OF PN JUNCTIONDIODE:


PN JUNCTION WITH NO APPLIED VOLTAGE OR OPENCIRCUIT
CONDITION:
In a piece of sc, if one half is doped by p type impurity and the other half is doped by n
type impurity, a PN junction is formed. The plane dividing the two halves or zones is called PN
junction. As shown in the fig the n type material has high concentration of free electrons, while p
type material has high concentration of holes. Therefore at the junction there is a tendency of
19

free electrons to diffuse over to the P side and the holes to the N side. This process is called

diffusion. As the free electrons move across the junction from N type to P type, the donor atoms
become positively charged. Hence a positive charge is built on the N-side of the junction. The
free electrons that cross the junction uncover the negative acceptor ions by filing the holes.
Therefore a negative charge is developed on the p –side of the junction..This net negative charge
on the p side prevents further diffusion of electrons into the p side. Similarly the net positive
charge on the N side repels the hole crossing from p side to N side. Thus a barrier sis set up near
the junction which prevents the further movement of charge carriers i.e. electrons and holes. As a
consequence of induced electric field across the depletion layer, an electrostatic potential
difference is established between P and N regions, which are called the potential barrier, junction
barrier, diffusion potential or contact potential, Vo. The magnitude of the contact potential Vo
varies with doping levels and temperature. Vo is 0.3V for Ge and 0.72 V for Si.

The electrostatic field across the junction caused by the positively charged N-Type region
tends to drive the holes away from the junction and negatively charged p type regions tend to
drive the electrons away from the junction. The majority holes diffusing out of the P region leave
behind negatively charged acceptor atoms bound to the lattice, thus exposing a negatives pace
charge in a previously neutral region. Similarly electrons diffusing from the N region expose
positively ionized donor atoms and a double space charge builds up at the junction as shown in
the fig. 1.7
20

It is noticed that the space charge layers are of opposite sign to the majority carriers
diffusing into them, which tends to reduce the diffusion rate. Thus the double space of the layer
causes an electric field to be set up across the junction directed from N to P regions, which is in
such a direction to inhibit the diffusion of majority electrons and holes as illustrated in fig 1.7.
The shape of the charge density, ρ, depends upon how diode id doped. Thus the junction region
is depleted of mobile charge carriers. Hence it is called depletion layer, space region, and
transition region. The depletion region is of the order of 0.5µm thick. There are no mobile
carriers in this narrow depletion region. Hence no current flows across the junction and the
system is in equilibrium. To the left of this depletion layer, the carrier concentration is p= N Aand
to its right it is n=ND.
21

FORWARD BIASED JUNCTIONDIODE

When a diode is connected in a Forward Bias condition, a negative voltage is applied to the N-
type material and a positive voltage is applied to the P-type material. If this external voltage
becomes greater than the value of the potential barrier, approx. 0.7 volts for silicon and 0.3 volts
for germanium, the potential barriers opposition will be overcome and current will start to flow.
This is because the negative voltage pushes or repels electrons towards the junction giving them
the energy to cross over and combine with the holes being pushed in the opposite direction
towards the junction by the positive voltage. This results in a characteristics curve of zero current
22

flowing up to this voltage point, called the "knee" on the static curves and then a high current
flow through the diode with little increase in the external voltage as shown below.

Forward Characteristics Curve for a Junction Diode

The application of a forward biasing voltage on the junction diode results in the depletion layer
becoming very thin and narrow which represents a low impedance path through the junction
thereby allowing high currents to flow. The point at which this sudden increase in current takes
place is represented on the static I-V characteristics curve above as the "knee" point.

Forward Biased Junction Diode showing a Reduction in the Depletion Layer


23

This condition represents the low resistance path through the PN junction allowing very large
currents to flow through the diode with only a small increase in bias voltage. The actual potential
difference across the junction or diode is kept constant by the action of the depletion layer at
approximately 0.3v for germanium and approximately 0.7v for silicon junction diodes. Since the
diode can conduct "infinite" current above this knee point as it effectively becomes a short
circuit, therefore resistors are used in series with the diode to limit its current flow. Exceeding its
maximum forward current specification causes the device to dissipate more power in the form of
heat than it was designed for resulting in a very quick failure of the device.

1.1.2 PN JUNCTION UNDER REVERSE BIAS CONDITION:

A silicon p–n junction in reverse bias.

Reverse Biased Junction Diode

When a diode is connected in a Reverse Bias condition, a positive voltage is applied to the N-
type material and a negative voltage is applied to the P-type material. The positive voltage
applied to the N-type material attracts electrons towards the positive electrode and away fromthe
junction, while the holes in the P-type end are also attracted away from the junction towards the
negative electrode. The net result is that the depletion layer grows wider due to a lack of
electrons and holes and presents a high impedance path, almost an insulator. The result is that a
high potential barrier is created thus preventing current from flowing through the semiconductor
material.

Reverse Biased Junction Diode showing an Increase in the Depletion Layer


24

This condition represents a high resistance value to the PN junction and practically zero current
flows through the junction diode with an increase in bias voltage. However, a very small leakage
current does flow through the junction which can be measured in microamperes, (μA). One final
point, if the reverse bias voltage Vr applied to the diode is increased to a sufficiently high enough
value, it will cause the PN junction to overheat and fail due to the avalanche effect around the
junction. This may cause the diode to become shorted and will result in the flow of maximum
circuit current, and this shown as a step downward slope in the reverse static characteristics
curve below.

Reverse Characteristics Curve for a Junction Diode


25

Sometimes this avalanche effect has practical applications in voltage stabilising circuits where a
series limiting resistor is used with the diode to limit this reverse breakdown current to a preset
maximum value thereby producing a fixed voltage output across the diode. These types of diodes
are commonly known as Zener Diodes and are discussed in a later tutorial.

V-I CHARACTERISTICS AND THEIRTEMPERATURE


DEPENDENCE:
Diode terminal characteristics equation for diode junction current:

v

I D  I(e vT
0 1)
Where VT = kT/q;
VD_ diode terminal voltage, Volts
Io _ temperature-dependent saturation current, µA
T _ absolute temperature of p-n junction, K
k _ Boltzmann’s constant 1.38x 10 -23J/K)
q _ electron charge 1.6x10-19 C
= empirical constant, 1 for Ge and 2 for Si

Temperature Effects on Diode


26

Temperature can have a marked effect on the characteristics of a silicon semiconductor diode as
shown in Fig. 1.24. It has been found experimentally that the reverse saturation current Io will just about
double in magnitude for every 10°C increase in temperature.

It is not uncommon for a germanium diode with an Io in the order of 1 or 2 A at 25°C to have a leakage
current of 100 A _ 0.1 mA at a temperature of 100°C. Typical values of Io for silicon are much lower than
that of germanium for similar power and current levels. The result is that even at high temperatures the
levels of Io for silicon diodes do not reach the same high levels obtained.for germanium—a very
important reason that silicon devices enjoy a significantly higher level of development and utilization in
design. Fundamentally, the open-circuit equivalent in the reverse bias region is better realized at any
temperature with silicon than with germanium. The increasing levels of Io with temperature account for
the lower levels of threshold voltage, as shown in Fig. 1.24. Simply increase the level of Io in and not rise
in diode current. Of course, the level of TK also will be increase, but the increasing level of Io will
overpower the smaller percent change in TK. As the temperature increases the forward characteristics are
actually becoming more“ideal,”

IDEAL VERSUS PRACTICAL RESISTANCELEVELS


DC or Static Resistance
The application of a dc voltage to a circuit containing a semiconductor diode will result in an
operating point on the characteristic curve that will not change with time. The resistance of the diode at
the operating point can be found simply by finding the corresponding levels of VD and ID as shown in
Fig. 1.25 and applying the followingEquation:
27

The dc resistance levels at the knee and below will be greater than the resistance levels obtained for the
vertical rise section of the characteristics. The resistance levels in the reverse-bias region will naturally be
quite high. Since ohmmeters typically employ a relatively constant-current source, the resistance
determined will be at a preset current level (typically, a few mill amperes).

Figure 1.25 determining the dc resistance of a diode at a particular operating point.

AC or Dynamic Resistance
It is obvious from Eq. 1.5 that the dc resistance of a diode is independent of the shape of the
characteristic in the region surrounding the point of interest. If a sinusoidal rather than dc input is applied,
the situation will change completely. The varying input will move the instantaneous operating point up
and down a region of the characteristics and thus defines a specific change in current and voltage as
shown in Fig. 1.27. With no applied varying signal, the point of operation would be the Q-point appearing
on Fig. 1.27 determined by the applied dc levels. The designation Q-point is derived from the word
quiescent, which means “still or unvarying.” A straight-line drawn tangent to the curve through the Q-
point as shown in Fig. 1.28 will define a particular change in voltage and current that can be used to
determine the ac or dynamic resistance for this region of the diode characteristics. In equationform,
28

DIODE EQUIVALENTCIRCUITS
An equivalent circuit is a combination of elements properly chosen to best represent the actual
terminal characteristics of a device, system, or such in a particular operating region. In other words, once
the equivalent circuit is defined, the device symbol can be removed from a schematic and the equivalent
circuit inserted in its place without severely affecting the actual behaviour of the system. The result is
often a network that can be solved using traditional circuit analysis techniques.

Piecewise-Linear Equivalent Circuit


One technique for obtaining an equivalent circuit for a diode is to approximate the characteristics
of the device by straight-line segments, as shown in Fig. 1.31. The resulting equivalent circuit is naturally
called the piecewise-linear equivalent circuit. It should be obvious from Fig. 1.31 that the straight-line
segments do not result in an exact duplication of the actual characteristics, especially in the knee region.
However, the resulting segments are sufficiently close to the actual curve to establish an equivalent circuit
that will provide an excellent first approximation to the actual behaviour of the device. The ideal diode is
included to establish that there is only one direction of conduction through the device, and a reverse-bias
condition will result in the open- circuit state for the device. Since a silicon semiconductor, diode does not
reach the conduction state until VD reaches 0.7 V with a forward bias (as shown in Fig. 1.31), a battery
VT opposing the conduction direction must appear in the equivalent circuit as shown in Fig. 1.32. The
battery simply specifies that the voltage across the device must be greater than the threshold battery
voltage before conduction through the device in the direction dictated by the ideal diode can be
established. When conduction is established, the resistance of the diode will be the specified value of rav.
29

The approximate level of rav can usually be determined from a specified operating point on the
specification sheet. For instance, for a silicon semiconductor diode, if IF _ 10 mA (a forward conduction
current for the diode) at VD _ 0.8 V, we know for silicon that a shift of 0.7 V is required before the
characteristics rise.
30

TRANSITION AND DIFFUSIONCAPACITANCE


Electronic devices are inherently sensitive to very high frequencies. Most shunt capacitive effects
that can be ignored at lower frequencies because the reactance XC=1/2πfC is very large (open-circuit
equivalent). This, however, cannot be ignored at very high frequencies. XC will become sufficiently small
due to the high value of f to introduce a low-reactance “shorting” path. In the p-n semiconductor diode,
there are two capacitive effects to be considered. In the reverse-bias region we have the transition- or
depletion region capacitance (CT), while in the forward-bias region we have the diffusion (CD) or storage
capacitance. Recall that the basic equation for the capacitance of a parallel-plate capacitor is defined by
C=€A/d, where € is the permittivity of the dielectric (insulator) between the plates of area A separated by
a distance d. In the reverse-, bias region there is a depletion region (free of carriers) that behaves
essentially like an insulator between the layers of opposite charge. Since the depletion width (d) will
increase with increased reverse-bias potential, the resulting transition capacitance will decrease. The fact
that the capacitance is dependent on the applied reverse-bias potential has application in a number of
electronic systems. Although the effect described above will also be present in the forward-bias region, it
is over shadowed by a capacitance effect directly dependent on the rate at which charge is injectedinto
31

the regions just outside the depletion region. The capacitive effects described above are represented by a
capacitor in parallel with the ideal diode, as shown in Fig. 1.38. For low- or mid-frequency applications
(except in the power area), however, the capacitor is normally not included in the diode symbol.

Diode capacitances: The diode exhibits two types of capacitances transition capacitance and diffusion

capacitance.

. Transition capacitance: The capacitance which appears between positive ion layer in n-region and

negative ion layer inp-region.

· Diffusion capacitance: This capacitance originates due to diffusion of charge carriers in the

oppositeregions.

The transition capacitance is very small as compared to the diffusion capacitance.

In reverse bias transition, the capacitance is the dominant and is given by:

where CT - transition capacitance

A - diode cross sectional area

W - depletion region width

In forward bias, the diffusion capacitance is the dominant and is given by:

where CD - diffusion capacitance

dQ - change in charge stored in depletion region

V - change in applied voltage

- time interval for change in voltage

g - diode conductance

r - diode resistance
32

The diffusion capacitance at low frequencies is given by the formula:

The diffusion capacitance at high frequencies is inversely proportional

to the frequency and is given by the formula:

Note: The variation of diffusion capacitance with applied voltage is used in the
design ofvaractor.

BREAK DOWNMECHANISMS

When an ordinary P-N junction diodeis reverse biased, normally only very small reverse saturation
current flows. This current is due to movement of minority carriers. It is almost independent of the
voltage applied. However, if the reverse bias is increased, a point is reached when the junction breaks
down and the reverse current increases abruptly. This current could be large enough to destroy the
junction. If the reverse current is limited by means of a suitable series resistor, the power dissipation at the
junction will not be excessive, and the device may be operated continuously in its breakdown region to its
normal (reverse saturation) level. It is found that for a suitably designed diode, the breakdown voltage is
very stable over a wide range of reverse currents. This quality gives the breakdowndiodemany useful
applications as a voltage referencesource.

The critical value of the voltage, at which the breakdown of a P-N junction diode occurs is called the
breakdown voltage. The breakdown voltage depends on the width of the depletion region, which, in turn,
depends on the doping level. The junction offers almost zero resistance at the breakdown point.

There are two mechanisms by which breakdown can occur at a reverse biased P-N junction :

1. avalanche breakdownand
2. Zenerbreakdown.

Avalanche breakdown and

The minority carriers, under reverse biased conditions, flowing through the junction acquire a
kinetic energy which increases with the increase in reverse voltage. At a sufficiently high reverse
voltage (say 5 V or more), the kinetic energy of minority carriers becomes so large that they
knock out electrons from the covalent bonds of the semiconductor material. As a result of
33

collision, the liberated electrons in turn liberate more electrons and the current becomes very
large leading to the breakdown of the crystal structure itself. This phenomenon is called the
avalanche breakdown. The breakdown region is the knee of the characteristic curve. Now the
current is not controlled by the junction voltage but rather by the external circuit.

Zener breakdown

Under a very high reverse voltage, the depletion region expands and the potential barrier increases leading
to a very high electric field across the junction. The electric field will break some of the covalent bonds of
the semiconductor atoms leading to a large number of free minority carriers, which suddenly increase the
reverse current. This is called the Zener effect. The breakdown occurs at a particular and constant value of
reverse voltage called the breakdown voltage, it is found that Zener breakdown occurs at electric field
intensity of about 3 x 10^7 V/m.

Either of the two (Zener breakdown or avalanche breakdown) may occur independently, or both
of these may occur simultaneously. Diode junctions that breakdown below 5 V are caused by Zener
effect. Junctions that experience breakdown above 5 V are caused by avalanche effect. Junctions that
breakdown around 5 V are usually caused by combination of two effects. The Zener breakdown occurs in
heavily doped junctions (P-type semiconductor moderately doped and N-type heavily doped), which
produce narrow depletion layers. The avalanche breakdown occurs in lightly doped junctions, which
produce wide depletion layers. With the increase in junction temperature Zener breakdown voltage is
reduced while the avalanche breakdown voltage increases. The Zener diodes have a negative temperature
coefficient while avalanche diodes have a positive temperature coefficient. Diodes that have breakdown
voltages around 5 V have zero temperature coefficient. The breakdown phenomenon is reversible and
harmless so long as the safe operating temperature ismaintained.

ZENERDIODES
34

The Zener diode is like a general-purpose signal diode consisting of a silicon PN junction. When biased
in the forward direction it behaves just like a normal signal diode passing the rated current, but as soon as
a reverse voltage applied across the zener diode exceeds the rated voltage of the device, the diodes
breakdown voltage VBis reached at which point a process called Avalanche Breakdown occurs in the
semiconductor depletion layer and a current starts to flow through the diode to limit this increase in
voltage.

The current now flowing through the zener diode increases dramatically to the maximum circuit value
(which is usually limited by a series resistor) and once achived this reverse saturation current remains
fairly constant over a wide range of applied voltages. This breakdown voltage point, VBis called the
"zener voltage" for zener diodes and can range from less than one volt to hundreds of volts.

The point at which the zener voltage triggers the current to flow through the diode can be very accurately
controlled (to less than 1% tolerance) in the doping stage of the diodes semiconductor construction giving
the diode a specific zener breakdown voltage, (Vz) for example, 4.3V or 7.5V. This zener breakdown
voltage on the I-V curve is almost a vertical straight line.

Zener Diode I-V Characteristics

The Zener Diode is used in its "reverse bias" or reverse breakdown mode, i.e. the diodes anode connects
35

to the negative supply. From the I-V characteristics curve above, we can see that the zener diode has a
region in its reverse bias characteristics of almost a constant negative voltage regardless of the value of
the current flowing through the diode and remains nearly constant even with large changes in current as
long as the zener diodes current remains between the breakdown current IZ(min)and the maximum current
ratingIZ(max).

This ability to control itself can be used to great effect to regulate or stabilise a voltage source against
supply or load variations. The fact that the voltage across the diode in the breakdown region is almost
constant turns out to be an important application of the zener diode as a voltage regulator. The function of
a regulator is to provide a constant output voltage to a load connected in parallel with it in spite of the
ripples in the supply voltage or the variation in the load current and the zener diode will continue to
regulate the voltage until the diodes current falls below the minimum IZ(min)value in the reverse breakdown
region.
36

UNIT-II
SPECIAL PURPOSE ELECTRONIC DEVICES AND
RECTIFIERS
PRINCIPLE OF OPERATION AND CHARACTERISTICS OF
TUNNELDIODE:
A tunnel diode or Esaki diode is a type of semiconductor diode which is capable of very fast
operation, well into the microwave frequency region, by using quantum mechanical effects.

It was invented in August 1957 by Leo Esaki when he was with Tokyo Tsushin Kogyo, now
known as Sony. In 1973 he received the Nobel Prize in Physics, jointly with Brian Josephson, for
discovering the electron tunneling effect used in these diodes. Robert Noyce independently came
up with the idea of a tunnel diode while working for William Shockley, but was discouraged
from pursuing it.

Fig:Tunnel diode schematic symbol

These diodes have a heavily dopedp–n junction only some 10 nm (100 Å) wide. The heavy
doping results in a broken bandgap, where conduction band electron states on the n-side are more
or less aligned with valence band hole states on the p-side.

Tunnel diodes were manufactured by Sony for the first time in 1957 followed by GeneralElectric
and other companies from about 1960, and are still made in low volume today. Tunnel diodes are
usually made from germanium, but can also be made in gallium arsenide and silicon materials.
They can be used as oscillators, amplifiers, frequency converters anddetectors.

Tunnelling Phenomenon:

In a conventional semiconductor diode, conduction takes place while the p–n junction is forward
biased and blocks current flow when the junction is reverse biased. This occurs up to a point
known as the “reverse breakdown voltage” when conduction begins (often accompanied by
destruction of the device). In the tunnel diode, the dopant concentration in the p and n layers are
increased to the point where the reverse breakdown voltage becomes zero and the diode
conducts in the reverse direction. However, when forward-biased, an odd effect occurs called
37

“quantum mechanical tunnelling” which gives rise to a region where an increase in forward
voltage is accompanied by a decrease in forward current. This negative resistance region can be
exploited in a solid state version of the dynatron oscillator which normally uses a
tetrodethermionic valve (or tube).

Forward bias operation

Under normal forward bias operation, as voltage begins to increase, electrons at first tunnel
through the very narrow p–n junction barrier because filled electron states in the conduction band
on the n-side become aligned with empty valence band hole states on the p-side of the p-n
junction. As voltage increases further these states become more misaligned and the current
drops – this is called negative resistance because current decreases with increasing voltage. As
voltage increases yet further, the diode begins to operate as a normal diode, where electrons
travel by conduction across the p–n junction, and no longer by tunneling through the p–n
junction barrier. Thus the most important operating region for a tunnel diode is the negative
resistance region.

Reverse bias operation

When used in the reverse direction they are called back diodes and can act as fast rectifiers with
zero offset voltage and extreme linearity for power signals (they have an accurate square law
characteristic in the reverse direction).

Under reverse bias filled states on the p-side become increasingly aligned with empty states on
the n-side and electrons now tunnel through the pn junction barrier in reverse direction – this is
the Zener effect that also occurs in zener diodes.

Technical comparisons
38

A rough approximation of the VI curve for a tunnel diode, showing the negative differential
resistance region.The Japanese physicist Leo Esaki invented the tunnel diode in 1958.It consists
of a p-n junction with highly doped regions. Because of the thinness of the junction, the electrons
can pass through the potential barrier of the dam layer at a suitable polarization, reaching the
energy states on the other sides of the junction. The current-voltage characteristic of the diode is
represented in Figure 1. In this sketch i p and Up are the peak, and iv and Uv are the valley
values for the current and voltage respectively. The form of this dependence can be qualitatively
explained by considering the tunneling processes that take place in a thin p-njunction.
39

Energy band structure of tunnel diode:

For the degenerated semiconductors, the energy band diagram at thermal equilibrium is
presented in Figure2.

In Figure 3 the tunneling processes in different points of the current voltage characteristic for the
tunnel diode are presented.

In Fig. 3a, the thermal equilibrium situation corresponding to point 1


40

from the Fig. 1 diagram presented; in this case the electrons will uniformly tunnel in both
directions, so the current will be null. At a direct polarization, a non-zero electron flow will
tunnel from the occupied states of the conduction band of the n region to the emptystates
of the valence band from the p region. The current attains a maximum when the overlap of the
empty and occupied states reaches the maximum value; a minimum value is reached when there
are no states for tunneling on the sides of the barrier. In this case, the tunnel current should drop
to zero.

Advantages of tunnel diodes:

 Environmental immunity i.e peak point is not a function oftemperature.


 lowcost.
 low noise.
 low powerconsumption.
 High speed i.e tunneling takes place very fast at the speed of light in the order of
nanoseconds
 simplicity i.e a tunnel diode can be used along with a d.c supply and a few passive
elements to obtain various applicationcircuits.

Applications for tunnel diodes:

 local oscillators for UHF televisiontuners


 Trigger circuits inoscilloscopes
 High speed counter circuits and very fast-rise time pulse generatorcircuits
 The tunnel diode can also be used as low-noise microwaveamplifier.

VARACTORDIODE:

Varactor diode is a special type of diode which uses transition capacitance property i.e voltage
variable capacitance .These are also called as varicap,VVC(voltage variable capacitance) or tuning
diodes.

The varactor diode symbol is shown below with a diagram representation.

Fig:symbol of varactor diode


41

When a reverse voltage is applied to a PN junction , the holes in the p-region are attracted to the
anode terminal and electrons in the n-region are attracted to the cathode terminal creating a region
where there is little current.This region ,the depletion region, is essentially devoid of carriers and
behaves as the dielectric of a capacitor.

The depletion region increases as reverse voltage across it increases; and since capacitance varies
inversely as dielectric thickness, the junction capacitance will decrease as the voltage across the
PN junction increases. So by varying the reverse voltage across a PN junction the junction
capacitance can be varied .This is shown in the typical varactor voltage-capacitance curve below.

Fig:voltage- capacitance curve

Notice the nonlinear increase in capacitance as the reverse voltage is decreased. This nonlinearity
allows the varactor to be used also as a harmonic generator.

Major varactor considerations are:


(a) Capacitancevalue
(b) Voltage
(c) Variation in capacitance withvoltage.
(d) Maximum workingvoltage
(e) Leakage current

Applications:

 Tunedcircuits.
 FMmodulators
 Automatic frequency controldevices
 Adjustable bandpassfilters
 Parametric amplifiers
 Televisionreceivers.

SCHOTTKYDIODE:
42

A Schottky diode is a majority carrier device, where electron-hole recombination is usually not
important. Hence, Schottky diodes have a much faster response under forward bias conditions
than p-n junction diodes. Therefore, Schottky diodes are used in applications where the speed of
a response is important, for example, in microwave detectors, mixers, and varactors. schottky
diodes are specially manufactured to solve the problem of fast switching which consists of a
metal to semiconductor junction.The symbol of schottky diode is as follows:

Fig:symbol of schottky diode

Structure and principle of operation


1. Structure

The structure of a metal-semiconductor junction is shown in Figure 1. It consists of a metal contacting a


piece of semiconductor. An ideal Ohmic contact, a contact such that no potential exists between the metal
and the semiconductor, is made to the other side of the semiconductor. The sign convention of the applied
voltage and current is also shown on Figure 1.

Figure 1 : Structure and sign convention of a metal-semiconductor junction


Flatband diagram and built-inpotential
The barrier between the metal and the semiconductor can be identified on an energy band diagram. To
constructsuchdiagramwefirstconsidertheenergybanddiagramofthemetalandthesemiconductor,and align
them using the same vacuum level as shown in Figure 2 (a). As the metal and semiconductor are brought
together, the Fermi energies of the metal and the semiconductor do not change right away. This yields the
flatband diagram of Figure 2(b).
43

Figure 2 : Energy band diagram of the metal and the semiconductor before (a) and after (b) contact is
made.

B, is defined as the potential difference between the Fermi energy of the metal andthe
band edge where the majority carriers reside. From Figure 2 (b) one finds that for an n-type semiconductor
the barrier height is obtainedfrom:

(1.1)

M
metals as measured in vacuum can be found in Table 1. For p-type material, the barrier height is given by
the difference between the valence band edge and the Fermi energy in the metal:

(1.2)

A metal-semiconductor junction will therefore form a barrier for electrons and holes if the Fermi energy of
the metal as drawn on the flatband diagram is somewhere between the conduction and valence band edge.

In addition, we define the built-in potenti I, as the difference between the Fermi energy of the metal and
that of the semiconductor.

(1.3)

(1.4)
44

Energy band diagram of a metal-semiconductor contact in thermal equilibrium.


The flatband diagram, shown in Figure 2 (b), is not a thermal equilibrium diagram, since the Fermi energy
in the metal differs from that in the semiconductor. Electrons in the n-type semiconductor can lower their
energy by traversing the junction. As the electrons leave the semiconductor, a positive charge, due to the
ionized donor atoms, stays behind. This charge creates a negative field and lowers the band edges of the
semiconductor. Electrons flow into the metal until equilibrium is reached between the diffusion of electrons
from the semiconductor into the metal and the drift of electrons caused by the field created by the ionized
impurity atoms. This equilibrium is characterized by a constant Fermi energy throughout the structure.

Figure 3 : Energy band diagram of a metal-semiconductor contact in thermal equilibrium.

It is of interest to note that in thermal equilibrium, i.e. with no external voltage applied, there is a region in
the semiconductor close to the junction which is depleted of mobile carriers. We call this the depletion
region. The potential across the semiconductor equals the built-in potential

Forward and reverse bias


Operation of a metal-semiconductor junction under forward and reverse bias is illustrated with Figure 4. As
a positive bias is applied to the metal (Figure 4 (a)), the Fermi energy of the metal is lowered with respectto
the Fermi energy in the semiconductor. This results in a smaller potential drop across thesemiconductor.
45

The balance between diffusion and drift is disturbed and more electrons will diffuse towards the metal than
the number drifting into the semiconductor. This leads to a positive current through the junction at a voltage
comparable to the built-in potential.

Figure 4 : Energy band diagram of a metal-semiconductor junction under (a) forward and (b) reverse
bias

As a negative voltage is applied (Figure 4 (b)), the Fermi energy of the metal is raised with respect to the
Fermi energy in the semiconductor. The potential across the semiconductor now increases, yielding a larger
depletion region and a larger electric field at the interface. The barrier, which restricts the electrons to the
metal, is unchanged so that the flow of electrons is limited by that barrier independent of the applied
voltage. The metal-semiconductor junction with positive barrier height has therefore a pronounced
rectifying behavior. A large current exists under forward bias, while almost no current exists under reverse
bias.

Characteristics of Schottky Diode:

Due to minority carrier free region, schottky diode cannot store the charge.Hence due to lack of charge
storage,it can switch off very fast than a conventional diode.it can be easily switched off for the frequencies
above 300MHz.The barrier at the junction for a schottky diode is less than that of normal p-n diode in both
forward and reverse bias region.The barrier potential and breakdown voltage in forward bias and reverse
bias region respectively are also less than p-n junction diode.The barrier potential is 0.25V as compared to
46

0.7V for normal diode.

Applications:

Due to fast switching characteristics this diode is very useful for high frequency applications such as digital
computer,high speed TTl,radar systems,mixers,detectors in communication equipments and analog to
digital converters.

PRINCIPLE OF OPERATION OFSCR


A silicon-controlled rectifier (or semiconductor-controlled rectifier) is a four-layer solid state
device that controls current. The name "silicon controlled rectifier" or SCR is General Electric's
trade name for a type of thyristor. The SCR was developed by a team of power engineers led by
Gordon Hall and commercialized by Frank W. "Bill" Gutzwiller in 1957.symbol of SCR is given
below:

Fig : symbol of SCR

Construction of SCR

An SCR consists of four layers of alternating P and N type semiconductor materials. Silicon is
used as the intrinsic semiconductor, to which the proper dopants are added. The junctions are
either diffused or alloyed. The planar construction is used for low power SCRs (and all the
junctions are diffused). The mesa type construction is used for high power SCRs. In this case,
junction J2 is obtained by the diffusion method and then the outer two layers are alloyed to it,
since the PNPN pellet is required to handle large currents. It is properly braced with tungsten or
molybdenum plates to provide greater mechanical strength. One of these plates is hard soldered
to a copper stud, which is threaded for attachment of heat sink. The doping of PNPN will depend
ontheapplicationofSCR,sinceitscharacteristicsaresimilartothoseofthethyratron.Today,
47

the term thyristor applies to the larger family of multilayer devices that exhibit bistable state-
change behaviour, that is, switching either ON or OFF.

The operation of a SCR and other thyristors can be understood in terms of a pair of tightly
coupled bipolar junction transistors, arranged to cause the self-latching action.The following
figures are construction of SCR,its two transistor model and symbol respectively

Fig: Construction,Two transistor model of SCR and symbol of SCR

. SCR Working Principle

The SCR is a four-layer, three-junction and a three-terminal device and is shown in fig.a. The
end P-region is the anode, the end N-region is the cathode and the inner P-region is the gate. The
anode to cathode is connected in series with the load circuit. Essentially the device is a switch.
Ideally it remains off (voltage blocking state), or appears to have an infinite impedance until both
the anode and gate terminals have suitable positive voltages with respect to the cathode terminal.
The thyristor then switches on and current flows and continues to conduct without further gate
signals. Ideally the thyristor has zero impedance in conduction state. For switching off or
reverting to the blocking state, there must be no gate signal and the anode current must be
reduced to zero. Current can flow only in onedirection.
48

In absence of external bias voltages, the majority carrier in each layer diffuses until there is a
built-in voltage that retards further diffusion. Some majority carriers have enough energy to cross
the barrier caused by the retarding electric field at each junction. These carriers then become
minority carriers and can recombine with majority carriers. Minority carriers in each layer can be
accelerated across each junction by the fixed field, but because of absence of external circuit in
this case the sum of majority and minority carrier currents must be zero.

A voltage bias, as shown in figure, and an external circuit to carry current allow internal currents
which include the following terms:

The current Ix is due to

 Majority carriers (holes) crossing junctionJ1


 Minority carriers crossing junctionJ1
 Holes injected at junction J2 diffusing through the N-region and crossing junction J1and
 Minority carriers from junction J2 diffusing through the N-region and crossing junction
J1.

V I characteristics of SCR:

As already mentioned, the SCR is a four-layer device with three terminals, namely, the anode,
the cathode and the gate. When the anode is made positive with respect to the cathode, junctions
J1 and J3 are forward biased and junction J2 is reverse-biased and only the leakage current will
flow through the device. The SCR is then said to be in the forward blocking state or in the
forwardmodeoroffstate.Butwhenthecathodeismadepositivewithrespecttotheanode,
49

junctions J1 and J3 are reverse-biased, a small reverse leakage current will flow through the SCR
and the SGR is said to be in the reverse blocking state or in reverse mode.

When the anode is positive with respect to cathode i.e. when the SCR is in forward mode, the
SCR does not conduct unless the forward voltage exceeds certain value, called the forward
breakover voltage, VFB0. In non-conducting state, the current through the SCR is the leakage
current which is very small and is negligible. If a positive gate current is supplied, the SCR can
become conducting at a voltage much lesser than forward break-over voltage. The larger the gate
current, lower the break-over voltage. With sufficiently large gate current, the SCR behaves
identical to PN rectifier. Once the SCR is switched on, the forward voltage drop across it is
suddenly reduced to very small value, say about 1 volt. In the conducting or on-state, the current
through the SCR is limited by the external impedance.

When the anode is negative with respect to cathode, that is when the SCR is in reverse mode or
in blocking state no current flows through the SCR except very small leakage current of the order
of few micro-amperes. But if the reverse voltage is increased beyond a certain value, called the
reverse break-over voltage, VRB0avalanche break down takes place. Forward break-over voltage
VFB0is usually higher than reverse breakovervoltage,VRBO.

From the foregoing discussion, it can be seen that the SCR has two stable and reversible
operating states. The change over from off-state to on-state, called turn-on, can be achieved by
increasing the forward voltage beyond VFB0. A more convenient and useful method of turn-on
the device employs the gate drive. If the forward voltage is less than the forward break-over
voltage, VFB0, it can be turned-on by applying a positive voltage between the gate and the
cathode. This method is called the gate control. Another very important feature of the gate is that
once the SCR is triggered to on-state the gate loses itscontrol.

The switching action of gate takes place only when

(i) SCR is forward biased i.e. anode is positive with respect to cathode,and

(ii) Suitable positive voltage is applied between the gate and thecathode.

Once the SCR has been switched on, it has no control on the amount of current flowing through
it. The current through the SCR is entirely controlled by the external impedance connected in the
circuit and the applied voltage. There is, however, a very small, about 1 V, potential drop across
the SCR. The forward current through the SCR can be reduced by reducing the applied voltage
or by increasing the circuit impedance. There is, however, a minimum forward current that must
be maintained to keep the SCR in conducting state. This is called the holding current rating of
SCR. If the current through the SCR is reduced below the level of holding current, the device
returns to off-state or blockingstate.

The SCR can be switched off by reducing the forward current below the level of holding current
which may be done either by reducing the applied voltage or by increasing the circuitimpedance.
50

Note : The gate can only trigger or switch-on the SCR, it cannot switch off.

Alternatively the SCR can be switched off by applying negative voltage to the anode (reverse
mode), the SCR naturally will be switched off.

Here one point is worth mentioning, the SCR takes certain time to switch off. The time, called
the turn-off time, must be allowed before forward voltage may be applied again otherwise the
device will switch-on with forward voltage without any gate pulse. The turn-off time is about 15
micro-seconds, which is immaterial when dealing with power frequency, but this becomes
important in the inverter circuits, which are to operate at highfrequency.

Merits of SCR

1. Very small amount of gate drive isrequired.


2. SCRs with high voltage and current ratings areavailable.
3.On state losses of SCR areless.

Demerits of SCR

1.Gate has no control,once SCR is turned on.


2.External circuits are required for turning it off.
3.Operationg frequencies are low.
4.Additional protection circuits are required.

Application of SCRs
SCRs are mainly used in devices where the control of high power, possibly coupled with high
voltage, is demanded. Their operation makes them suitable for use in medium to high-voltage
AC power control applications, such as lamp dimming, regulators and motorcontrol.

SCRs and similar devices are used for rectification of high power AC in high-voltage
directcurrent power transmission

PHOTODIODE:
The photo diode is a semiconductor p-n junction device whose region of operation is limited to
the reverse biased region.The figure below shows the symbol of photodiode
51

Fig:Symbol for photodiode.

Principle of operation:
A photodiode is a type of photo detector capable of converting light into either current or
voltage, depending upon the mode of operation. The common, traditional solar cell used to
generate electric solar power is a large area photodiode. A photodiode is designed to operate in
reverse bias. The deletion region width is large.Under normal conditions it carries small reverse
current due to minority charge carriers.When light is incident through glass window on the p-n
junction,photons in the light bombard the p-n junction and some energy s imparted to the valence
electrons.So valence electrons break covalent bonds and become free electrons.Thus more
electron-hole pairs are generated.Thus total number of minority charge carriers increases and
hence reverse current increases.This is the basic principle of operation of photodiode.

Characteristics of photodiode:
When the P-N junction is reverse-biased, a reverse saturation current flows due to thermally
generated holes and electrons being swept across the junction as the minority carriers. With the
increase in temperature of the junction more and more hole-electron pairs are created and so the
reverse saturation current I0 increases. The same effect can be had by illuminating the junction.
When light energy bombards a P-N junction, it dislodges valence electrons. The more light
striking the junction the larger the reverse current in a diode. It is due to generation of more and
more charge carriers with the increase in level of illumination. This is clearly shown in ‘ figure
52

for different intensity levels. The dark current is the current that exists when no light is incident.
It is to be noted here that current becomes zero only with a positive applied bias equals to VQ.
The almost equal spacing between the curves for the same increment in luminous flux reveals
that the reverse saturation current I0increases linearly with the luminous flux as shown in figure.
Increase in reverse voltage does not increase the reverse current significantly, because all
available charge carriers are already being swept across the junction. For reducing the reverse
saturation current I0 to zero, it is necessary to forward bias the junction by an amount equal to
barrier potential. Thus the photodiode can be used as a photoconductivedevice.

Fig: characteristics of photodiode

On removal of reverse bias applied across the photodiode, minority charge carriers continue to
be swept across the junction while the diode is illuminated. This has the effect of increasing the
concentration of holes in the P-side and that of electrons in the N-side But the barrier potential is
negative on the P-side and positive on the N-side, and was created by holes flowing from P to N-
side and electrons from N to P-side during fabrication of junction. Thus the flow of minority
carriers tends to reduce the barrier potential.

When an external circuit is connected across the diode terminals, the minority carrier; return to
the original side via the external circuit. The electrons which crossed the junction from P to N-
side now flow out through the N-terminal and into the P-terminal This means that the device is
behaving as a voltage cell with the N-side being the negative terminal and the P-side the positive
terminal. Thus, the photodiode is & photovoltaic device as well as photoconductive device.

Advantages:
The advantages of photodiode are:
1. It can be used as variable resistancedevice.
53

2. Highly sensitive to the light.


3. The speed of operation is veryhigh.

Disadvantages:
1.Temperature dependent dark current.
2.poor temperature stability.
3.Current needs amplification for driving other circuits.

Applications:

1.Alarm system.
2.counting system.

Problems:
1. In a particular application single phase half wave rectifier using SCR is used.The average load
voltage is 80V.If supply voltage is 230V,50Hz a.c.find the firing angle of the SCR.

2. In a particular application single phase half wave rectifier using SCR s used.The supply
voltage is 325sin t where =100πrad/sec.Find the time for which SCR remains OFF ifforward
breakover voltage is125V.

. RECTIFIERS & FILTERS:


INTRODUCTION
For the operation of most of the electronics devices and circuits, a d.c. source is required. So it is
advantageous to convert domestic a.c. supply into d.c.voltages. The process of converting a.c.
voltage into d.c. voltage is called as rectification. This is achieved with i) Step-down
Transformer, ii) Rectifier, iii) Filter and iv) Voltage regulatorcircuits.
These elements constitute d.c. regulated power supply shown in the fig 1 below.
54

 Transformer – steps down 230V AC mains to low voltageAC.


 Rectifier – converts AC to DC, but the DC output isvarying.
 Smoothing – smooth the DC from varying greatly to a smallripple.
 Regulator – eliminates ripple by setting DC output to a fixedvoltage.

The block diagram of a regulated D.C. power supply consists of step-down transformer,
rectifier, filter, voltage regulator and load. An ideal regulated power supply is an electronics
circuit designed to provide a predetermined d.c. voltage Vo which is independent of the load
current and variations in the input voltage ad temperature. If the output of a regulator circuit is a
AC voltage then it is termed as voltage stabilizer, whereas if the output is a DC voltage then it is
termed as voltage regulator.

RECTIFIER:
Any electrical device which offers a low resistance to the current in one direction but a high resistance to
the current in the opposite direction is called rectifier. Such a device is capable of converting a sinusoidal
input waveform, whose average value is zero, into a unidirectional Waveform, with a non-zero average
component. A rectifier is a device, which converts a.c. voltage (bi-directional) to pulsating d.c. voltage
(Unidirectional).

Characteristics of a Rectifier Circuit:


Any electrical device which offers a low resistance to the current in one direction but a high
resistance to the current in the opposite direction is called rectifier. Such a device is capable of
converting a sinusoidal input waveform, whose average value is zero, into a unidirectional
waveform, with a non-zero average component.
55

A rectifier is a device, which converts a.c. voltage (bi-directional) to pulsating d.c..Load


currents: They are two types of output current. They are average or d.c. current and RMS
currents.

Average or DC current: The average current of a periodic function is defined as the area of one
cycle of the curve divided by the base.
It is expressed mathematically as

Area over oneperiod


i) Average value/dc value/mean value=
Total time period

1T
Vdc 
T Vd (wt)
0

ii) Effective (or) R.M.Scurrent:

The effective (or) R.M.S. current squared ofa periodic function of time is given by the area of one
cycle of the curve, which represents the square of the function divided by the base.

1T 2
T 0
Vrms  V d (wt)

iii) Peakfactor:
It is the ratio of peak value to Rms value

peakvalue
Peak factor =
rmsvalue
iv) Formfactor:

It is the ratio of Rms value to average value


56

Rmsvalue
Formfactor=
averagevalue

v) RippleFactor():ItisdefinedasrationofR.M.S.valueofa.c.componenttothed.c.
component in the output is known as “RippleFactor”.
Vac

Vdc

Vac  Vrms
2
Vdc2

vi) Efficiency ( ):

It is the ratio of d.c output power to the a.c. input power. It signifies, how efficiently the rectifier circuit
converts a.c. power into d.c. power.

o / p power

i / p power

vii) Peak Inverse Voltage(PIV):


It is defined as the maximum reverse voltage that a diode can withstand without destroying
the junction.

viii) Transformer Utilization Factor(UTF):

The d.c. power to be delivered to the load in a rectifier circuit decides the rating of the
Transformer used in the circuit. So, transformer utilization factor is defined as

Pdc
TUF 
pac(rated)

ix) %Regulation:
57

The variation of the d.c. output voltage as a function of d.c. load current is called regulation. The
percentage regulation is defined as

VNL VFL
% Re gulation  *100
VFL

For an ideal power supply, % Regulation is zero.

CLASSIFICATION OFRECTIFIERS:
Using one or more diodes in the circuit, following rectifier circuits can be designed.

1) Half - WaveRectifier
2) Full – WaveRectifier
3) BridgeRectifier

HALF-WAVERECTIFIER:
A Half – wave rectifier as shown in fig 2 is one, which converts a.c. voltage into a pulsating voltage
using only one half cycle of the applied a.c. voltage.

The a.c. voltage is applied to the rectifier circuit using step-down transformer-rectifying element i.e.,
p-n junction diode and the source of a.c. voltage, all connected is series. The a.c. voltage is applied
to the rectifier circuit using step-down transformer
58

V=Vm sin (wt)


The input to the rectifier circuit, Where Vm is the peak value of secondary a.c. voltage.

Operation:
For the positive half-cycle of input a.c. voltage, the diode D is forward biased and hence it conducts.
Now a current flows in the circuit and there is a voltage drop across RL. The waveform of the diode
current (or) load current is shown in fig 3.
For the negative half-cycle of input, the diode D is reverse biased and hence it does not
Conduct. Now no current flows in the circuit i.e., i=0 and Vo=0. Thus for the negative half- cycle no
power is delivered to the load.

Analysis:
In the analysis of a HWR, the following parameters are to be analyzed.

1. DC outputcurrent
2. DC Outputvoltage
3. R.M.S.Current
4. R.M.S.voltage
5. Rectifier Efficiency (η )

6. Ripple factor (γ)


7. PeakFactor
8. %Regulation
9. Transformer Utilization Factor(TUF)
59

10. formfactor
11. o/p frequency

Let a sinusoidal voltage Vi be applied to the input of the rectifier.


Then V=Vm sin (wt) Where Vm is the maximum value of the secondary voltage. Let the diode be
idealizedtopiece-wiselinearapproximationwithresistanceRfintheforwarddirectioni.e.,intheON state
and Rr (=∞) in the reverse direction i.e., in the OFF state. Now the current ‘i’ in the diode (or) in the
load resistance RL isgivenby V=Vmsin(wt)

i) AVERAGE VOLTAGE

1T
Vdc  Vd(wt)
T 0
1 2
Vdc 
T V ()d
0
1 2

Vdc   V ()d

2 

1
Vdc 
20
V m sin(wt)

V
Vdc  m



ii).AVERAGE CURRENT:

I
Idc  m


iii) RMS VOLTAGE:

1T
Vrms 
T 0
V 2 d (wt)
60



1 2
Vrms  
2 0
(Vmsim(wt)) d2 (wt)




V
Vrms  m
2



IV) RMSCURRENT

I
I rms  m

V) PEAKFACTOR

peakvalue
Peak factor =
rmsvalue

Vm
Peak Factor =
(Vm / 2)

Peak Factor =2

vi) FORMFACTOR

Rmsvalue
Form factor=
averagevalue

(Vm / 2)
Form factor=
Vm / 

Form Factor =1.57

vii) Ripple Factor:


61

Vac

Vdc

Vac  Vrms
2
Vdc2

V 2 V2
 rms dc
Vac

2
Vrms
 1
Vdc2

1.21

viii) Efficiency ( ):

o / ppower
 *100
i / ppower
pac
= *100
Pdc

=40.8

ix) Transformer Utilization Factor(TUF):


The d.c. power to be delivered to the load in a rectifier circuit decides the rating of the transformer
used in the circuit. Therefore, transformer utilization factor is defined as
pdc
TUF 
Pac(rated)

TUF =0.286.
The value of TUF is low which shows that in half-wave circuit, the transformer is not fully utilized.
If the transformer rating is 1 KVA (1000VA) then the half-wave rectifier can deliver
1000 X 0.287 = 287 watts to resistance load.

x) Peak Inverse Voltage(PIV):


62

It is defined as the maximum reverse voltage that a diode can withstand without destroying the
junction. The peak inverse voltage across a diode is the peak of the negative half- cycle. For half-
wave rectifier, PIV is Vm.

DISADVANTAGES OF HALF-WAVE RECTIFIER:

1. The ripple factor ishigh.


2. The efficiency islow.
3. The Transformer Utilization factor islow.
Because of all these disadvantages, the half-wave rectifier circuit is normally not used as a
power rectifier circuit.

FULL WAVERECTIFIER:
A full-wave rectifier converts an ac voltage into a pulsating dc voltage using both half cycles of
the applied ac voltage. In order to rectify both the half cycles of ac input, two diodes are used in
this circuit. The diodes feed a common load RL with the help of a center-tap transformer. A
center-tap transformer is the one, which produces two sinusoidal waveforms of same magnitude
and frequency but out of phase with respect to the ground in the secondary winding of the
transformer. The full wave rectifier is shown in the fig 4 below
63

Fig. 5 shows the input and output wave forms of the ckt.
During positive half of the input signal, anode of diode D1 becomes positive and at the
same time the anode of diode D2 becomes negative. Hence D1 conducts and D2 does not
conduct. The load current flows through D1 and the voltage drop across RL will be equal to the
input voltage.
During the negative half cycle of the input, the anode of D1 becomes negative and the
anode of D2 becomes positive. Hence, D1 does not conduct and D2 conducts. The load current
flows through D2 and the voltage drop across RL will be equal to the input voltage. It is noted
that the load current flows in the both the half cycles of ac voltage and in the same direction
through the load resistance.

i) AVERAGEVOLTAGE

ii) AVERAGECURRENT
64

iii) RMSVOLTAGE:

1T
Vrms 
T 0
V 2 d (wt)



2
1
2 
Vrms  (Vmsim(wt)) d2 (wt)
 0







IV) RMSCURRENT

2I
I rms  m


V) PEAKFACTOR

peakvalue
Peak factor =
rmsvalue
65

Vm
Peak Factor =
(Vm / 2)

Peak Factor =2

vi) FORMFACTOR

Rms value
Form factor=
averagevalue

Form factor= (Vm / 2)


2Vm / 

Form Factor =1.11

vii) Ripple Factor:

viii) Efficiency ( ):

o / ppower
 *100
i / ppower
66

ix) Transformer Utilization Factor(TUF):

The d.c. power to be delivered to the load in a rectifier circuit decides the rating of the
transformer used in the circuit. So, transformer utilization factor is defined as
pdc
TUF 
Pac(rated)

x) Peak Inverse Voltage(PIV):

It is defined as the maximum reverse voltage that a diode can withstand without destroying the
67

junction. The peak inverse voltage across a diode is the peak of the negative half- cycle. For half-
wave rectifier, PIV is 2Vm

xi) %Regulation

.
Advantages

1) Ripple factor = 0.482 (against 1.21 forHWR)


2) Rectification efficiency is 0.812 (against 0.405 forHWR)
3) Better TUF (secondary) is 0.574 (0.287 forHWR)
4) No core saturation problem
Disadvantages:
1) Requires center tappedtransformer.

BRIDGERECTIFIER.

Another type of circuit that produces the same output waveform as the full wave rectifier circuit
above, is that of the Full Wave Bridge Rectifier. This type of single phase rectifier uses four
individual rectifying diodes connected in a closed loop "bridge" configuration to produce the
desired output. The main advantage of this bridge circuit is that it does not require a special
centre tapped transformer, thereby reducing its size and cost. The single secondary winding is
connected to one side of the diode bridge network and the load to the other side as shownbelow.

The Diode Bridge Rectifier


68

The four diodes labelled D1 to D4 are arranged in "series pairs" with only two diodes conducting
current during each half cycle. During the positive half cycle of the supply, diodes D1 and D2
conduct in series while diodes D3 and D4 are reverse biased and the current flows through the
load as shown below (fig 7).

The Positive Half-cycle

The Negative Half-cycle

During the negative half cycle of the supply, diodes D3 and D4 conduct in series (fig 8), but
diodes D1 and D2 switch "OFF" as they are now reverse biased. The current flowing through the
load is the same direction as before.
69

As the current flowing through the load is unidirectional, so the voltage developed across the
load is also unidirectional the same as for the previous two diode full-wave rectifier, therefore
the average DC voltage across the load is 0.637Vmax. However in reality, during each half cycle
the current flows through two diodes instead of just one so the amplitude of the output voltage is
two voltage drops ( 2 x 0.7 = 1.4V ) less than the input V MAX amplitude. The ripple frequency is
now twice the supply frequency (e.g. 100Hz for a 50Hz supply)
70

FILTERS

The output of a rectifier contains dc component as well as ac component. Filters are used to
minimize the undesirable ac i.e., ripple leaving only the dc component to appear at the output.

Some important filters are:

1. Inductorfilter

2. Capacitorfilter
3. LC or L sectionfilter
4. CLC or Π-typefilter

CAPACITOR FILTER

This is the most simple form of the filter circuitand in this arrangement a high value capacitor C
is placed directly across the output terminals, as shown in figure. During the conduction period it
gets charged and stores up energy to it during non-conduction period. Through this process, the
time duration during which Ft is to be noted here that the capacitor C gets charged to the peak
because there is no resistance (except the negligible forward resistance of diode) in the charging
path. But the discharging time is quite large (roughly 100 times more than the charging time
depending upon the value of RL) because it discharges through load resistanceRL.
71

The function of the capacitor filter may be viewed in terms of impedances. The large value
capacitor C offers a low impedance shunt path to the ac components or ripples but offers high
impedance to the dc component. Thus ripples get bypassed through capacitor C and only dc
component flows through the load resistance RL

Capacitor filter is very popular because of its low cost, small size, light weight and good
characteristics.
72
73

CAPACITOR FILTER WITH HWR

CAPACITOR FILTER WITH FWR


74
75

The worthnoting points about shunt capacitor filter are:

1. For a fixed-value filter capacitance larger the load resistance RL larger will be the discharge
time constant CRL and therefore, lower the ripples and more the output voltage. On the other
hand lower the load resistance (or more the load current), lower will be the outputvoltage.

2. Similarly smaller the filter capacitor, the less charge it can hold and more it will discharge.
Thus the peak-to-peak value of the ripple will increase, and the average dc level will decrease.
Larger the filter capacitor, the more charge it can hold and the less it will discharge. Hence the
peak-to-peak value of the ripple will be less, and the average dc level will increase. But, the
maximum value of the capacitance that can be employed is limited by another factor. The larger
the capacitance value, the greater is the current required to charge the capacitor to a given
voltage. The maximum current that can be handled by a diode is limited by the figure quoted by
the manufacturer. Thus the maximum value of the capacitance, that can be used in the shunt filter
capacitor islimited.
76

SERIES INDUCTORFILTER.

In this arrangement a high value inductor or choke L is connected in series with the rectifier
element and the load, as illustrated in figure. The filtering action of an inductor filter depends
upon its property of opposing any change in the current flowing through it. When the output
current of the rectifier increases above a certain value, energy is stored in it in the form of
magnetic field and this energy is given up when the output current falls below the average value.
Thus by placing a choke coil in series with the rectifier output and load, any sudden change in
current that might have occurred in the circuit without an inductor is smoothed out by the
presence of the inductor L.

The function of the inductor filter may be viewed in terms of impedances. The choke offers high
impedance to the ac components but offers almost zero resistance to the desired dc components.
Thus ripples are removed to a large extent. Nature of the output voltage without filter and with
choke filter is shown in figure.
77

For dc (zero frequency), the choke resistance Rc in series with the load resistance RL forms a
voltage divider and dc voltage across the load is given as

where Vdc is dc voltage output from a full-wave rectifier. Usually choke coil resistance Rc, is
much small than RL and, therefore, almost entire of the dc voltage is available across the load
resistance RL.

Since the reactance of inductor increases with the increase in frequency, better filtering of the
higher harmonic components takes place, so effect of third and higher harmonic voltages can be
neglected.

As obvious from equation , if choke coil resistance Rc is negligible in comparison to load


resistance RL, then the entire dc component of rectifier output is available across 2 RL and isequal
to — VLmax. The ac voltage partly drops across XL and partly overRL.

L-SECTION FILTER:
A simple series inductor reduces both the peakand effective values of the output current and
output voltage. On the other hand a simple shunt capacitor filterreduces the ripple voltage but
increases the diode current. The diode may get damaged due to large current and at the same
time it causes greater heating of supply transformer resulting in reducedefficiency.

In an inductor filter, ripple factor increases with the increase in load resistance RL while in a
capacitor filter it varies inversely with load resistance RL.

From economical point of view also, neither series inductor nor shunt capacitor type filters are
suitable.

Practical filter-circuitsare derived by combining the voltage stabilizing action of shunt capacitor
with the current smoothing action of series choke coil. By using combination of inductor and
capacitor ripple factor can be lowered, diode current can be restricted and simultaneously ripple
factor can be made almost independent of load resistance (or load current). Two types of most
commonly used combinations are choke-input or L-section filter-and capacitor-input or Pi-Filter.
78

Choke-input filter is explained below:

Choke-input filter consists of a choke L connected in series with the rectifier and a capacitor C
connected across the load . This is also sometimes called the L-section filter because in this
arrangement inductor and capacitor are connected, as an inverted L. ln figure only one filter
section is shown. But several identical sections are often employed to improve the smoothing
action. (The choke L on the input side of the filter readily allows dc to pass but opposes the flow
of ac components because its dc resistance is negligibly small but ac impedance is large. Any
fluctuation that remains in the current even after passing through the choke are largely by-passed
around the load by the shunt capacitor because Xc is much smaller than RL. Ripples can be
reduced effectively by making XL greater than Xc at ripple frequency. However, a small ripple
still remains in the filtered output and this is considered negligible if it than l%. The rectified and
filtered output voltage waveforms from a full-wave re with choke-input filter are shown in
figure.
79

Π-SECTION FILTER:

Capacitor-Input or Pi-Filter.

Such a filter consists of a shunt capacitor C1 at the input followed by an L-section filter formed
by series inductor L and shunt capacitor C2. This is also called the n-filter because the shape of
the circuit diagram for this filter appears like Greek letter n (pi). Since the rectifier feeds directly
into the capacitor so it is also called capacitor input filter.

As the rectified output is fed directly into a capacitor C1. Such a filter can be used with a half-
wave rectifier (series inductor and L-section filters cannot be used with half-wave rectifiers).
Usually electrolytic capacitors are used even though their capacitances are large but they occupy
minimum space. Usually both capacitors C1 and C2 are enclosed in one metal container. The
metal container serves as, the common ground for the two capacitors.

A capacitor-input or pi- filter is characterized by a high voltage output at low current drains.
Such a filter is used, if, for a given transformer, higher voltage than that can be obtained from an
L-section filter is required and if low ripple than that can be obtained from a shunt capacitor
filter or L-section filter is desired. In this filter, the input capacitor C1 is selected to offer very
low reactance to the ripple frequency. Hence major part of filtering is accomplished by theinput
80

capacitor C1. Most of the remaining ripple is removed by the L-section filter consisting of a
choke L and capacitor C2.)

The action of this filter can best be understood by considering the action of L-section filter,
formed by L and C2, upon the triangular output voltage wave from the input capacitor C1 The
charging and discharging action of input capacitor C1 has already been discussed. The output
voltage is roughly the same as across input capacitor C1 less the dc voltage drop in inductor. The
ripples contained in this output are reduced further by L-section filter. The output voltage of pi-
filter falls off rapidly with the increase in load-current and, therefore, the voltage regulation with
this filter is very poor.

SALIENT FEATURES OF L-SECTION AND PI-FILTERS.

1. In pi-filter the dc output voltage is much larger than that can be had from an L-section filter
with the same inputvoltage.

2.In pi-filter ripples are less in comparison to those in shunt capacitor or L-section filter. So
smaller valued choke is required in a pi-filter in comparison to that required in L-sectionfilter.

3.In pi-filter, the capacitor is to be charged to the peak value hence the rms current in supply
transformer is larger as compared in case of L-sectionfilter.

4.Voltage regulation in case of pi-filter is very poor, as already mentioned. So n-filters are
suitable for fixed loads whereas L-section filters can work satisfactorily with varying loads
provided a minimum current ismaintained.

5.In case of a pi-filter PIV is larger than that in case of an L-sectionfilter.

COMPARISON OF FILTERS
1) A capacitor filter provides Vm volts at less load current. But regulation ispoor.
2) An Inductor filter gives high ripple voltage for low load currents. It is used for
high loadcurrents
3) L – Section filter gives a ripple factor independent of load current.Voltage
Regulation can be improved by use of bleeder resistance
4) Multiple L – Section filter or π filters give much less ripple than the single L –
SectionFilter.
81
82

UNIT III
TRANSISTORS
INTRODUCTI
ON
A bipolar junction transistor (BJT) is a three terminal device in which operation depends on the
interaction of both majority and minority carriers and hence the name bipolar. The BJT is
analogus to vacuum triode and is comparatively smaller in size. It is used i amplifier and
oscillator circuits, and as a switch in digital circuits. It has wide applications in computers,
satellites and other modern communication systems.

CONSTRUCTION OF BJT AND ITSSYMBOLS


The Bipolar Transistor basic construction consists of two PN-junctions producing three
connecting terminals with each terminal being given a name to identify it from the other two.
These three terminals are known and labelled as the Emitter ( E ), the Base ( B ) and the
Collector ( C ) respectively. There are two basic types of bipolar transistor construction, PNP
and NPN, which basically describes the physical arrangement of the P-type and N-type
semiconductor materials from which they aremade.

Transistors are three terminal active devices made from different semiconductor materials that
can act as either an insulator or a conductor by the application of a small signal voltage. The
transistor's ability to change between these two states enables it to have two basic functions:
"switching" (digital electronics) or "amplification" (analogue electronics). Then bipolar
transistors have the ability to operate within three different regions:

 1. Active Region - the transistor operates as an amplifier and Ic =β.Ib


 2. Saturation - the transistor is "fully-ON" operating as a switch and Ic =I(saturation) 
 3. Cut-off - the transistor is "fully-OFF" operating as a switch and Ic =0

Bipolar Transistors are current regulating devices that control the amount of current flowing
through them in proportion to the amount of biasing voltage applied to their base terminal acting
like a current-controlled switch. The principle of operation of the two transistor types PNP and
NPN, is exactly the same the only difference being in their biasing and the polarity of the power
supply for each type(fig 1).
83

Bipolar Transistor Construction

 Fig:1
The construction and circuit symbols for both the PNP and NPN bipolar transistor are
given above with the arrow in the circuit symbol always showing the direction of
"conventional current flow" between the base terminal and its emitter terminal. The
direction of the arrow always points from the positive P-type region to the negative N-
type region for both transistor types, exactly the same as for the standard diode symbol

Transistor Operation:
Working of a n-p-n transistor:

The n-p-n transistor with base to emitter junction forward biased and collector base junction
reverse biased is as shown in figure.
84

As the base to emitter junction is forward biased the majority carriers emitted by the n-type
emitter i.e., electrons have a tendency to flow towards the base which constitutes the emitter current IE.

As the base is p-type there is chance of recombination of electrons emitted by the emitter with
the holes in the p-type base. But as the base is very thin and lightly doped only few electrons emitted
by the n-type emitter less than 5% combines with the holes in the p-type base, theRemaining more
than 95% electrons emitted by the n-type emitter cross over into the collector region constitute
the collectorcurrent .

IE = IB + IC

Working of a p-n-p transistor:

The p-n-p transistor with base to emitter junction is forward biased and collector to base
junction reverse biased is as show in figure.

As the base to emitter junction is forward biased the majority carriers emitted by the p-type
emitter i.e., holes have a tendency to flow towards the base which constitutes the emitter current IE.

As the base is n-type there is a chance of recombination of holes emitted by the emitter with
the electrons in the n-type base. But as the base us very thin and lightly doped only few electrons less
than 5% combine with the holes emitted by the p-type emitter, the remaining 95% charge carriers cross
over into the collector region to constitute thecollectorcurrent.

IE = IB + IC
85

TRANSISTOR CURRENTCOMPONENTS:

FIG 2

The above fig 2 shows the various current components, which flow across the forward biased
emitter junction and reverse- biased collector junction. The emitter current IEconsists of hole
current IPE (holes crossing from emitter into base) and electron current InE(electrons crossing
from base into emitter).The ratio of hole to electron currents, IpE/ InE , crossing the emitter
junction is proportional to the ratio of the conductivity of the p material to that of the n
material. In a transistor, the doping of that of the emitter is made much larger than the doping
of the base. This feature ensures (in p-n-p transistor) that the emitter current consists an
almost entirely of holes. Such a situation is desired since the current which results from
electrons crossing the emitter junction from base to emitter does not contribute carriers,
which can reach thecollector.

Not all the holes crossing the emitter junction JE reach the the collector junction JC
Because some of them combine with the electrons in n-type base. If IpC is hole current at junction JC
there must be a bulk recombination current ( IPE- IpC ) leaving the base.

Actually, electrons enter the base region through the base lead to supply those charges, which have
been lost by recombination with the holes injected in to the base across JE.If the emitter were open
circuited so that IE=0 then IpC would be zero. Under these circumstances, the base and collector
current IC would equal the reverse saturation current ICO. If IE≠0then
IC= ICO- IpC
86

For a p-n-p transistor, ICO consists of holes moving across JCfrom left to right (base to collector) and
electrons crossing JC in opposite direction. Assumed referenced direction for ICO i.e. from right to left,
then for a p-n-p transistor, ICOis negative. For an n-p-n transistor, ICO is positive.The basic operation
will be described using the pnp transistor. The operation of the pnp transistor is exactly the same if the
roles played by the electron and hole are interchanged.

One p-n junction of a transistor is reverse-biased, whereas the other is forward-biased.

Forward-biased junction of a pnptransistor

Reverse-biased junction of a pnptransistor

Both biasing potentials have been applied to a pnp transistor and resulting majority and minority
carrier flows indicated.

Majority carriers (+) will diffuse across the forward-biased p-n junction into the n-type material.
87

A very small number of carriers (+) will through n-type material to the base terminal. Resulting
IB is typically in order of microamperes.

The large number of majority carriers will diffuse across the reverse-biased junction into the p-
type material connected to the collector terminal

Applying KCL to the transistor :

IE = IC + IB

The comprises of two components – the majority and minority carriers

IC = ICmajority + ICOminority

ICO – ICcurrent with emitter terminal open and is called leakage current

Various parameters which relate the current components is given below

Emitter efficiency:

currentofinjectedcar riersatJ E

totalemitt ercurrent

IPE I
  pE
I pE InE I nE

Transport Factor:

injectedca rriercurrentreachingJC
* 
injectedca rrierncurrentatJ E
IpC
* 
InE

Large signal current gain:

The ratio of the negative of collector current increment to the emitter current change from zero (cut-
off)to IE the large signal current gain of a common base transistor.

 (IC ICO )

IE

Since ICand IE have opposite signs, then α, as defined, is always positive. Typically numerical
values of α lies in the range of 0.90 to 0.995
88

I pC I pC I pE
  *
IE InE IE
* 

The transistor alpha is the product of the transport factor and the emitter efficiency. This
statement assumes that the collector multiplication ratio * is unity. * is the ratio of total current
crossing JC to hole arriving at thejunction.

Bipolar TransistorConfigurations

As the Bipolar Transistor is a three terminal device, there are basically three possible ways
to connect it within an electronic circuit with one terminal being common to both the input
and output. Each method of connection responding differently to its input signal within a
circuit as the static characteristics of the transistor vary with each circuit arrangement.

 1. Common Base Configuration - has Voltage Gain but no CurrentGain.


 2 Common Emitter Configuration - has both Current and VoltageGain. 
 3. Common Collector Configuration - has Current Gain but no VoltageGain.

COMMON-BASECONFIGURATION

Common-base terminology is derived from the fact that the : base is common to both input
and output of t configuration. base is usually the terminal closest to or at ground potential.
Majority carriers can cross the reverse-biased junction because the injected majority carriers
will appear as minority carriers in the n-type material. All current directions will refer to
conventional (hole) flow and the arrows in all electronic symbols have a direction defined by
this convention.

Note that the applied biasing (voltage sources) are such as to establish current in the direction
indicated for each branch.
89

To describe the behavior of common-base amplifiers requires two set of characteristics:

1. Input or driving pointcharacteristics.


2. Output or collector characteristics

The output characteristics has 3 basicregions:

 Active region –defined by the biasingarrangements


 Cutoff region – region where the collector current is 0A
 Saturation region- region of the characteristics to the left of VCB =0V
90

The curves (output characteristics) clearly indicate that a first approximation to the relationship
between IE and IC in the active region is given by

IC ≈IE

Once a transistor is in the ‘on’ state, the base-emitter voltage will be assumed to beVBE = 0.7V

In the dc mode the level of IC and IE due to the majority carriers are related by a quantity called alpha
= αdc

IC = IE + ICBO

It can then be summarize to IC = IE (ignore ICBO due to small value)

For ac situations where the point of operation moves on the characteristics curve, an ac alpha defined
by αac
91

Alpha a common base current gain factor that shows the efficiency by calculating the current percent
from current flow from emitter to collector. The value of  is typical from 0.9 ~ 0.998.

Biasing:Proper biasing CB configuration in active region by approximation I C IE (IB 0 uA)

COMMON-EMITTERCONFIGURATION

It is called common-emitter configuration since : emitter is common or reference to both input


and output terminals.emitter is usually the terminal closest to or at ground potential.

Almost amplifier design is using connection of CE due to the high gain for current and voltage.

Two set of characteristics are necessary to describe the behavior for CE ;input (base terminal) and
output (collector terminal) parameters.

Proper Biasing common-emitter configuration in active region


92

IB is microamperes compared to miliamperes of IC.

IB will flow when VBE> 0.7V for silicon and 0.3V for germanium

Before this value IB is very small and no IB.

Base-emitter junction is forward bias Increasing VCE will reduce IB for different values.

Output characteristics for acommon-emitter npn transistor

For small VCE (VCE< VCESAT, IC increase linearly with increasing of VCE
93

VCE> VCESAT IC not totally depends on VCE constant IC

IB(uA) is very small compare to IC (mA). Small increase in IB cause big increase in IC

IB=0 A  ICEO occur.

Noticing the value when IC=0A. There is still some value of current flows.

Beta () or amplification factor

The ratio of dc collector current (IC) to the dc base current (IB) is dc beta (dc ) which is dc
current gain where IC and IB are determined at a particular operating point, Q-point (quiescent
point). It’s define by the following equation:

30 <dc < 300  2N3904

On data sheet, dc=hfe with h is derived from ac hybrid equivalent cct. FE are derived from
forward-current amplification and common-emitter configuration respectively.
94

For ac conditions, an ac beta has been defined as the changes of collector current (I C) compared to
the changes of base current (IB) where IC and IB are determined at operating point. On data sheet,
ac=hfe It can defined by the following equation:

From output characteristics of commonemitter configuration, find ac and dc with an

Operating point at IB=25 A and VCE =7.5V


95
96

Relationship analysis between α and β

COMMON – COLLECTORCONFIGURATION

Also called emitter-follower (EF). It is called common-emitter configuration since both


the signal

source and the load share the collector terminal as a common connection point.The output
voltage is obtained at emitter terminal. The input characteristic of common-collector
configuration is similar with common-emitter. configuration.Common-collector circuit
configuration is provided with the load resistor connected from emitter to ground.It is used
primarily for impedance-matching purpose since it has high input impedance and low output
impedance.
97

For the common-collector configuration, the output characteristics are a plot of IE vs VCE for a
range of values of IB.

Limits of opearation

Many BJT transistor used as an amplifier. Thus it is important to notice the limits of operations.At
least 3 maximum values is mentioned in data sheet.

There are:
98

a) Maximum power dissipation at collector: P Cmaxor PD

b) Maximum collector-emitter voltage: VCEmax sometimes named as VBR(CEO)


orVCEO.

c) Maximum collector current: ICmax

There are few rules that need to be followed for BJT transistor used as an amplifier. The rules are:
transistor need to be operate in active region!

IC < ICmax

PC < PCmax

Note: VCE is at maximum and IC is at minimum (ICMAX=ICEO)inthe cutoff region. ICis


at maximum and VCEis at minimum (VCEmax = Vcesat = VCEO) in the saturation region. The
transistor operates in the active region between saturation andcutoff.
99

Refer to the fig. Example; A derating factor of 2mW/°C indicates the power dissipation is reduced
2mW each degree centigrade increase of temperature.

Step1:

The maximum collector powerdissipation,

PD=ICMAX x VCEmax= 18m x 20 = 360mW

Step 2:

At any point on the characteristics the product of and must be equal to 360 mW.

Ex. 1. If choose ICmax= 5 mA, substitute into the (1), we get

VCEmaxICmax= 360 mW

VCEmax(5 m)=360/5=7.2 V

Ex.2. If choose VCEmax=18 V, substitute into (1), we get


100

VCEmaxICmax= 360 mW

(10) ICMAX=360m/18=20 mA

Derating PDmax

PDMAX is usually specified at 25°C.

The higher temperature goes, the less is P DMAX

Example;A derating factor of 2mW/°C indicates the power dissipation is reduced 2mW each
degree centigrade increase of temperature.

THE TRANSISTOR AS ANAMPLIFIER


Consider the circuit fragment shown at right, which includes an NPN transistor connected
between two power supply “rails” VCC and VEE (with, naturally, VCC >VEE ). Assume that
some method has been used to bias the transistor’s base terminal at the voltage VB >VEE
so that the transistor’s base-emitter junction is forward-biased and conductingcurrent
IB as shown (we’ll discuss ways of biasing the transistor in a subsequent section). What
we want to determine are the relationships between the various voltages and currents, the
resistor values RC and RE , and the transistor’s β

We start the analysis by connecting the base and emitter voltages using the forward
bias diode drop

VBE ≈ 0.6V across the base-emitter PN junction. As we know from our previous studyof
the semiconductor diode, this voltage will be a very weak function of the base current IB ,
sowewillusetheworkingassumptionthatitisafixed,constantvalue.Consequently,if
we know VB , then we also know VE , and vice versa. Given VE , we now know the
voltage drop across the resistor RE , so we also know the current through it: I E = (VE −
VEE) RE.

Knowing IE and the transistor’s current gain β immediately tells us the other two
transistor currents IB and IC , since the currents are related through β as shown in below
Figure The value of RC then gives us the collector voltage VC ,since I C = (VCC −VC) RC
.Thuswehavesucceededinrelatingthecircuit’sstatevariables(currentsandvoltages),as
we set out to do. Note that there are some conditions that must be met for our solution to be
realistic: all the currents must flow in the directions shown by the arrows in Figure , and it
must be the case that VEE <VE <VB ≤ VC <VCC . If one or more of these conditions is violated
by our solution, then our solution fails, and the transistor circuit is operating as a switch
rather than as an amplifier (we’ll discuss transistor switch circuits in the nextsection).
101
102

Transistor as switch
103

FIELD EFFECT TRANSISTOR


INTRODUCTION
1. The Field effect transistor is abbreviated as FET , it is an another semiconductor device like a
BJT which can be used as an amplifier orswitch.
2. The Field effect transistor is a voltage operated device. Whereas Bipolar junction transistor is a
current controlled device. Unlike BJT a FET requires virtually no inputcurrent.
3. This gives it an extremely high input resistance , which is its most important advantage over a
bipolartransistor.
4. FET is also a three terminal device, labeled as source, drain andgate.
5. The source can be viewed as BJT’s emitter, the drain as collector, and the gate as the counter
part of the base.
6. The material that connects the source to drain is referred to as thechannel.

7. FET operation depends only on the flow of majority carriers ,therefore they are called uni polar
devices. BJT operation depends on both minority and majoritycarriers.

8. As FET has conduction through only majority carriers it is less noisy thanBJT.

9. FETs are much easier to fabricate and are particularly suitable for ICs because they occupy
less space thanBJTs.

10. FET amplifiers have low gain bandwidth product due to the junction capacitive effects and
produce more signal distortion except for small signaloperation.
104

11. The performance of FET is relatively unaffected by ambient temperature changes. As it has a
negative temperature coefficient at high current levels, it prevents the FET from thermal
breakdown. The BJT has a positive temperature coefficient at high current levels which leads
to thermalbreakdown.

CLASSIFICATION OFFET:
There are two major categories of field effect transistors:

1. Junction Field EffectTransistors

2. MOSFETs

These are further sub divided in to P- channel and N-channel devices.

MOSFETs are further classified in to two types Depletion MOSFETs and Enhancement
. MOSFETs

When the channel is of N-type the JFET is referred to as an N-channel JFET ,when the
channel is of P-type the JFET is referred to as P-channel JFET.

The schematic symbols for the P-channel and N-channel JFETs are shown in the figure.

CONSTRUCTION AND OPERATION OF N- CHANNEL


FET
If the gate is an N-type material, the channel must be a P-type material.

CONSTRUCTION OF N-CHANNEL JFET


105

A piece of N- type material, referred to as channel has two smaller pieces of P-type material
attached to its sides, forming PN junctions. The channel ends are designated as the drain and
source . And the two pieces of P-type material are connected together and their terminal is
called the gate. Since this channel is in the N-type bar, the FET is known as N-channelJFET.

OPERATION OF N-CHANNEL JFET:-

The overall operation of the JFET is based on varying the width of the channel to control the drain
current.

A piece of N type material referred to as the channel, has two smaller pieces of P
type material attached to its sites, farming PN –Junctions. The channel’s ends are designated the
drain and the source. And the two pieces of P type material are connected together and their
terminal is called the gate. With the gate terminal not connected and the potential applied positive
at the drain negative at the source a drain current Id flows. When the gate is biased negative with
respective to the source the PN junctions are reverse biased and depletion regions are formed. The
channel is more lightly doped than the P type gate blocks, so the depletion regions penetrate deeply
into the channel. Since depletion region is a region depleted of charge carriers it behaves as an
Insulator. The result is that the channel is narrowed. Its resistance is increased and Id is reduced.
When the negative gate bias voltage is further increased, the depletion regions meet at the center
and Id is cut offcompletely.

There are two ways to control the channel width

1. By varying the value ofVgs


2. And by Varying the value of Vds holding Vgsconstant

1 By varying the value of Vgs :-

We can vary the width of the channel and in turn vary the amount of drain
current. This can be done by varying the value of Vgs. This point is illustrated in the fig below.
Here we are dealing with N channel FET. So channel is of N type and gate is of P type that
constitutes a PN junction. This PN junction is always reverse biased in JFET operation .The
reversebiasisappliedbyabatteryvoltageVgsconnectedbetweenthegateandthesource
106

terminal i.e positive terminal of the battery is connected to the source and negative terminal to
gate.

1) When a PN junction is reverse biased the electrons and holes diffuse across junction by
leaving immobile ions on the N and P sides , the region containing these immobile ions is
known as depletionregions.
2) If both P and N regions are heavily doped then the depletion region extends symmetrically
on bothsides.
3) But in N channel FET P region is heavily doped than N type thus depletion region extends
more in N region than Pregion.
4) So when no Vds is applied the depletion region is symmetrical and the conductivity becomes
Zero. Since there are no mobile carriers in thejunction.
5) Asthereversebiasvoltageisincreasesthethicknessofthedepletionregionalsoincreases.
i.e. the effective channel width decreases .
6) By varying the value of Vgs we can vary the width of thechannel.

2 Varying the value of Vds holding Vgs constant :-

1) When no voltage is applied to the gate i.e. Vgs=0 , Vds is applied between source and drain
the electrons will flow from source to drain through the channel constituting drain currentId
.
2) With Vgs= 0 for Id= 0 the channel between the gate junctions is entirely open .In response to
a small applied voltage Vds , the entire bar acts as a simple semi conductor resistor and the
current Id increases linearly with Vds.
3) The channel resistances are represented as rd and rs as shown in thefig.
107

4) This increasing drain current Id produces a voltage drop across rd which reverse biases the
gate to source junction,(rd> rs) .Thus the depletion region is formed which is not
symmetrical.
5) The depletion region i.e. developed penetrates deeper in to the channel near drain and less
towardssourcebecauseVrd>>Vrs.Soreversebiasishigherneardrainthanatsource.
6) As a result growing depletion region reduces the effective width of the channel. Eventually a
voltage Vds is reached at which the channel is pinched off. This is the voltage where the
current Id begins to level off and approach a constantvalue.
7) So, by varying the value of Vds we can vary the width of the channel holding Vgsconstant.

When both Vgs and Vds is applied:-

It is of course in principle not possible for the channel to close Completely and there by reduce
the current Id to Zero for, if such indeed, could be the case the gate voltage Vgs is applied in the
direction to provide additional reverse bias

1) When voltage is applied between the drain and source with a battery Vdd, the electrons
flow from source to drain through the narrow channel existing between thedepletion
108

regions. This constitutes the drain current Id, its conventional direction is from drain to
source.
2) The value of drain current is maximum when no external voltage is applied between gate
and source and is designated byIdss.

3) When Vgs is increased beyond Zero the depletion regions are widened. This reduces the
effective width of the channel and therefore controls the flow of drain current through the
channel.
4) When Vgs is further increased a stage is reached at which to depletion regions touch each
other that means the entire channel is closed with depletion region. This reduces the drain
current toZero.

CHARACTERISTICS OF N-CHANNEL JFET:-


The family of curves that shows the relation between current and voltage are known as
characteristic curves.

There are two important characteristics of a JFET.

1) Drain or VICharacteristics
2) Transfercharacteristics

1. DrainCharacteristics:-

Drain characteristics shows the relation between the drain to source voltage
Vds and drain current Id. In order to explain typical drain characteristics let us consider the
curve with Vgs= 0.V.
109

1) When Vds is applied and it is increasing the drain current I D also increases linearly up to
kneepoint.
2) This shows that FET behaves like an ordinary resistor.This region is called as ohmicregion.
3) ID increases with increase in drain to source voltage. Here the drain current is increased
slowly as compared to ohmicregion.

4)
5)
6)

4) It is because of the fact that there is an increase in V DS .This in turn increases the reverse
bias voltage across the gate source junction .As a result of this depletion region grows in size
thereby reducing the effective width of thechannel.

5) All the drain to source voltage corresponding to point the channel width is reduced to a
minimum value and is known as pinchoff.

6) The drain to source voltage at which channel pinch off occurs is called pinch offvoltage(Vp).

PINCH OFF Region:-

1) This is the region shown by the curve as saturationregion.


2) It is also called as saturation region or constant current region. Because of the channel is
occupied with depletion region , the depletion region is more towards the drain and less
towards the source, so the channel is limited, with this only limited number of carriers
are only allowed to cross this channel from source drain causing a current that is
constantinthisregion.TouseFETasan amplifieritisoperatedinthissaturationregion.
3) In this drain current remains constant at its maximum valueI DSS.

4) The drain current in the pinch off region depends upon the gate to source voltage and is
given by therelation

Id =Idss [1-Vgs/Vp]2
This is known as shokley’s relation.
110

BREAKDOWN REGION:-

1) The region is shown by the curve .In this region, the drain current increases rapidly as
the drain to source voltage isincreased.
2) It is because of the gate to source junction due to avalancheeffect.
3) The avalanche break down occurs at progressively lower value of VDS because the
reverse bias gate voltage adds to the drain voltage thereby increasing effective voltage
across the gatejunction
This causes

1. The maximum saturation drain current issmaller


2. The ohmic region portiondecreased.
4) It is important to note that the maximum voltage VDS which can be applied to FET is the
lowest voltage which causes available breakdown.

2. TRANSFERCHARACTERISTICS:-

These curves shows the relationship between drain current I D and gate to source
voltage VGS for different values ofVDS.

1) First adjust the drain to source voltage to some suitable value , then increase the gate
to source voltage in small suitablevalue.
2) Plot the graph between gate to source voltage along the horizontal axis and current
I Don the vertical axis. We shall obtain a curve likethis.
111

3) As we know that if Vgs is more negative curves drain current to reduce . where Vgs is
made sufficiently negative, Id is reduced to zero. This is caused by the widening of the
depletion region to a point where it is completely closes the channel. The value of Vgsat
the cutoff point is designed asVgsoff

4) The upper end of the curve as shown by the drain current value is equal to I dss that is
when Vgs = 0 the drain current ismaximum.

5) While the lower end is indicated by a voltage equal toVgsoff


6) IfVgscontinuouslyincreasing,thechannelwidth isreduced, thenId=0
7) It may be noted that curve is part of the parabola; it may be expressedas
Id=Idss[1-Vgs/Vgsoff]2

DIFFERENCE BETWEEN Vp AND Vgsoff –

Vp is the value of Vgs that causes the JFET to become constant current component, It is
measured at Vgs =0V and has a constant drain current of Id=Idss .Where Vgsoff is the value of Vgs that
reduces Id to approximately zero.

Why the gate to source junction of a JFET be always reverse biased ?

The gate to source junction of a JFET is never allowed to become forward biased because
the gate material is not designed to handle any significant amount of current. If the junction is
allowed to become forward biased, current is generated through the gate material. This current may
destroy the component.

There is one more important characteristic of JFET reverse biasing i.e. J FET ‘s
have extremely high characteristic gate input impedance. This impedance is typically in the high
mega ohm range. With the advantage of extremely high input impedance it draws no current from
the source. The high input impedance of the JFET has led to its extensive use in integrated circuits.
The low current requirements of the component makes it perfect for use in ICs. Where thousands of
transistors must be etched on to a single piece of silicon. The low current draw helps the IC to
remain relatively cool, thus allowing more components to be placed in a smaller physicalarea.

JFETPARAMETERS
The electrical behavior of JFET may be described in terms of certain parameters. Such parameters
are obtained from the characteristiccurves.

A C Drain resistance(rd):

It is also called dynamic drain resistance and is the a.c.resistance between the drain and source
terminal,when the JFET is operating in the pinch off or saturation region.It is given by the ratio of
small change in drain to source voltage ∆Vds to the corresponding change in drain current ∆I d for a
constant gate to source voltage Vgs.

Mathematically it is expressed as rd=∆Vds/ ∆Id where Vgs is held constant.


112

TRANCE CONDUCTANCE (gm):

It is also called forward transconductance . It is given by the ratio of small change in drain current
(∆Id) to the corresponding change in gate to source voltage (∆Vds)

Mathematically the transconductance can be written as

gm=∆Id/∆Vds

AMPLIFICATION FACTOR (µ)

It is given by the ratio of small change in drain to source voltage (∆Vds) to the corresponding change
in gate to source voltage (∆Vgs)for a constant drain current (Id).

Thus µ=∆Vds/∆Vgs when Id held constant

The amplification factor µ may be expressed as a product of transconductance (g m)and ac drain


resistance (rd)

µ=∆Vds/∆Vgs=gm rd

MOSFET:-
We now turn our attention to the insulated gate FET or metal oxide semi conductor FET which is
having the greater commercial importance than the junction FET.

Most MOSFETS however are triodes, with the substrate internally connected to the source. The
circuit symbols used by several manufacturers are indicated in the Fig below.

(a) DepletiontypeMOSFET (b) Enhancement typeMOSFET

Both of them are P- channel

Here are two basic types of MOSFETS


113

(1) Depletiontype (2) Enhancement type MOSFET.

D-MOSFETS can be operated in both the depletion mode and the enhancement mode. E MOSFETS
are restricted to operate in enhancement mode. The primary difference between them is their
physical construction.

The construction difference between the two is shown in the fig given below.

As we can see the D MOSFET have physical channel between the source and drain
terminals(Shaded area)

The E MOSFET on the other hand has no such channel physically. It depends on the gate
voltage to form a channel between the source and the drainterminals.
114

Both MOSFETS have an insulating layer between the gate and the rest of the component.
This insulating layer is made up of SIO2 a glass like insulating material. The gate material is made up
of metal conductor .Thus going from gate to substrate, we can have metal oxide semi conductor
which is where the term MOSFET comes from.

Since the gate is insulated from the rest of the component, the MOSFET is
sometimes referred to as an insulated gate FET orIGFET.

The foundation of the MOSFET is called the substrate. This material is represented in the schematic
symbol by the center line that is connected to the source.

In the symbol for the MOSFET, the arrow is placed on the substrate. As with JFET an arrow pointing
in represents an N-channel device, while an arrow pointing out represents p-channeldevice.

CONSTRUCTION OF AN N-CHANNEL MOSFET:-

The N- channel MOSFET consists of a lightly doped p type substance into which two heavily
doped n+ regions are diffused as shown in the Fig. These n+ sections , which will act as source and
drain. A thin layer of insulation silicon dioxide (SIO2) is grown over the surface of the structure, and
holes are cut into oxide layer, allowing contact with the source and drain. Then the gate metal area
is overlaid on the oxide, covering the entire channel region.Metal contacts are made to drain and
source and the contact to the metal over the channel area is the gate terminal.The metal area of the
gate, in conjunction with the insulating dielectric oxide layer and the semiconductor channel, forms
a parallel plate capacitor. The insulating layer ofsio2

Is the reason why this device is called the insulated gate field effect transistor. This layer results in an
extremely high input resistance (10 10 to 10power 15ohms) for MOSFET.

DEPLETION MOSFET
The basic structure of D –MOSFET is shown in the fig. An N-channel is diffused between source
and drain with the device an appreciable drain current IDSS flows foe zero gate to source voltage,
Vgs=0.

Depletion mode operation:-


115

1) The above fig shows the D-MOSFET operating conditions with gate and source terminals
shortedtogether(VGS=0V)

2) At this stage ID= IDSS where VGS=0V, with this voltage VDS, an appreciable drain current IDSS
flows.

3) If the gate to source voltage is made negative i.e. VGs is negative .Positive charges are induced
in the channel through the SIO2 of the gatecapacitor.

4) Since the current in a FET is due to majority carriers(electrons for an N-type material) , the
inducedpositivechargesmakethechannellessconductiveandthedraincurrentdropsasVgs is
made morenegative.

5) The re distribution of charge in the channel causes an effective depletion of majority carriers ,
which accounts for the designation depletionMOSFET.

6) That means biasing voltage Vgs depletes the channel of free carriers This effectively reduces
the width of the channel , increasing itsresistance.

7) Note that negative Vgs has the same effect on the MOSFET as it has on theJFET.

8) As shown in the fig above, the depletion layer generated by Vgs (represented by the white
space between the insulating material and the channel) cuts into the channel, reducing its
width.Asaresult,Id<Idss.TheactualvalueofIDdependsonthevalueofIdss,Vgs(off)andVgs.

Enhancement mode operation of the D-MOSFET:-

1) This operating mode is a result of applying a positive gate to source voltage Vgs to the
device.
2) When Vgs is positive the channel is effectively widened. This reduces the resistance of the
channel allowing ID to exceed the value ofIDSS
3) When Vgs is given positive the majority carriers in the p-type are holes. The holes in the p
type substrate are repelled by the +ve gatevoltage.
4) At the same time, the conduction band electrons (minority carriers) in the p type material
are attracted towards the channel by the +gatevoltage.
5) With the build up of electrons near the channel , the area to the right of the physical
channel effectively becomes an N typematerial.
6) The extended n type channel now allows more current, Id>Idss
116

Characteristics of Depletion MOSFET:-

The fig. shows the drain characteristics for the N channel depletion type MOSFET

1) The curves are plotted for both Vgs positive and Vgs negativevoltages
.
2) When Vgs=0 and negative the MOSFET operates in depletion mode when Vgs is positive ,the
MOSFET operates in the enhancementmode.
3) The difference between JFET and D MOSFET is that JFET does not operate for positive values
ofVgs.

4) When Vds=0, there is no conduction takes place between source to drain, if Vgs<0 and
Vds>0 then Id increaseslinearly.

5) But as Vgs,0 induces positive charges holes in the channel, and controls the channel width.
Thustheconductionbetweensourceto drainismaintainedasconstant,i.e.Idisconstant.

6) If Vgs>0 the gate induces more electrons in channel side, it is added with the free electrons
generated by source. again the potential applied to gate determines the channel width and
maintains constant current flow through it as shown inFig
117

TRANSFER CHARACTERISTICS:-

The combination of 3 operating states i.e. Vgs=0V, VGs<0V, Vgs>0V is represented by the D
MOSFET transconductance curve shown in Fig.

1) Here in this curve it may be noted that the region AB of the characteristics similar to that of
JFET.

2) This curve extends for the positive values ofVgs

3) Note that Id=Idss for Vgs=0V when Vgs is negative,Id< Idss when Vgs= Vgs(off) ,Id is reduced
to approximately omA.Where Vgs is positive Id>Idss.So obviously Idss is not the maximum
possible value of Id for aMOSFET.
118

4) ThecurvesaresimilartoJFETso thettheD MOSFEThavethesametransconductance


equation.

E-MOSFETS
The E MOSFET is capable of operating only in the enhancement mode.The gate potential
must be positive w.r.t to source.

1) when the value of Vgs=0V, there is no channel connecting the source and drain
materials.

2) As aresult , there can be no significant amount of draincurrent.

3) When Vgs=0, the Vdd supply tries to force free electrons from source to drain but the
presence of p-region does not permit the electrons to pass through it. Thus there is no
drain current atVgs=0,

4) If Vgs is positive, it induces a negative charge in the p type substrate just adjacent to
the SIO2layer.

5) As the holes are repelled by the positive gate voltage, the minority carrier electrons
attracted toward this voltage. This forms an effective N type bridge between source
and drain providing a path for draincurrent.

6) This +ve gate voltage forma a channel between the source anddrain.

7) This produces a thin layer of N type channel in the P type substarate.This layer of free
electrons is called N type inversionlayer.
119

8) The minimum Vgs which produces this inversion layer is called threshold voltage and
is designated by Vgs(th).This is the point at which the device turns on is called the
threshold voltageVgs(th)
9) When the voltage Vgs is <Vgs (th) no current flows from drain tosource.

10) How ever when the voltage Vgs > Vgs (th) the inversion layer connects the drainto
source and we get significant values ofcurrent.

CHARACTERISTICS OF E MOSFET:-
1. DRAINCHARACTERISTICS

The volt ampere drain characteristics of an N-channel enhancement mode MOSFET are given in

the fig.
120

2. TRANSFER CHARACTERISTICS:-

1) The current Idss at Vgs≤ 0 is very small beinf of the order of a few nanoamps.
2) As Vgs is made +ve , the current Id increases slowly at forst, and then much more
rapidly with an increase inVgs.
3) The standard transconductance formula will not work for the EMOSFET.
4) To determine the value of ID at a given value of VGs we must use the following
relation
Id =K[Vgs-Vgs(Th)]2

Where K is constant for the MOSFET . found as

K=

From the data specification sheets, the 2N7000 has the following ratings.

Id(on)= 75mA(minimum).

And Vgs(th)=0.8(minimum)

APPLICATION OFMOSFET
One of the primary contributions to electronics made by MOSFETs can be found in the
area of digital (computer electronics). The signals in digital circuits are made up of
rapidly switching dc levels. This signal is called as a rectangular wave ,made up of two dc
levels (or logic levels). These logic levels are 0V and+5V.

A group of circuits with similar circuitry and operating characteristics is referred to as a


logic family. All the circuits in a given logic family respond to the same logic levels, have
similar speed and power-handling capabilities , and can be directly connected together.
One such logic family is complementary MOS (or CMOS) logic. This logic family is
made up entirely ofMOSFETs.
121

COMPARISON OF MOSFET WITHJFET


a. In enhancement and depletion types of MOSFET, the transverse electric field
induced across an insulating layer deposited on the semiconductor material
controls the conductivity of thechannel.

b. IntheJFETthetransverseelectricfieldacrossthe reversebiasedPNjunction
controls the conductivity of thechannel.

c. The gate leakage current in a MOSFET is of the order of 10 -12A. Hence the input
resistance of a MOSFET is very high in the order of 1010 to 1015 Ω. The gate
leakage current of a JFET is of the order of 10-9A., and its input resistance is of
the order of108Ω.

d. The output characteristics of the JFET are flatter than those of the MOSFET,
and hence the drain resistance of a JFET (0.1 to 1MΩ) is much higher than that
of a MOSFET (1 to50kΩ).

e. JFETs are operated only in the depletion mode. The depletion typeMOSFET
may be operated in both depletion and enhancementmode.

f. Comparing to JFET, MOSFETs are easier tofabricate.

g. Special digital CMOS circuits are available which involve near zero power
dissipation and very low voltage and current requirements. This makesthem
suitable for portablesystems.

UNIJUNCTION TRANSISTOR(UJT):
Another device whose construction is similar to that of the FET is shown in the figure.
122

It is a three terminal device, having two layers.It consists of a slab of lightly doped N-type
silicon material. The two base contacts are attached to both ends of this N-type surface. These
are denoted as B1 and B2 respectively.

A P-type material is used to form a pn junction at the boundary of the aluminium rod and
N-type slab. The N-type is lightly doped while P-type is heavily doped. That is N-type
provides high resistivity and P-type provides low resistivity.

This device was originally described in the literature as the double-base diode, but is now
commercially available under the designation Uni Junction transistor (UJT).

The standard symbol for this device is shown in the fig.

Here the emitter arrow is inclined and points toward B1 and This emitter arrow which is at an
angle to the vertical line representing N-type material. This arrow indicates the direction of
flow of conventional current when UJT is forward biased.

EQUIVALENT CIRCUIT OF UJT

The circuit of UJT is shown in the fig.

In the construction ,the terminal emitter is closer to B2 as compared to B1.

If we see the equivalent circuit of UJT, The internal resistances of the two bases are
represented as Rb1and Rb2. Hence Rb1 is greater than Rb2. The pn junction is represented by a
123

normal diode with Vd as the drop acrossit. When the emitter diode is not conducting then
the resistance between the two bases B1 and B2 is called interbase resistance denotesRbb

Rbb=Rb1+Rb2

Its value ranges from 4kΩ to 12kΩ

Intrinsic stand off ratio (η)

Consider UJT as shown in the fig. to which supply Vbb is connected. With Ie=0, That is
emitter diode is not conducting ,

Rbb=Rb1+Rb2

Then the voltage drop across Rb1 can be obtained by using potential divider rule.

Replacing with its equivalent circuit

Rbb=Rb1+Rb2

When Ie =0

VRB1= ) VBB = η.VBB WhenIe=0

η = Intrinsic stand offratio= ) when Ie=0


124

η= )whenIe=0

The value of η is from 0.5 to 0.8 the voltage Vrb1 is called intrinsic stand off voltage, because
it keeps the emitter diode reverse biased for all emitter voltages less than V rb1.

Operation

1. The supply Vbb is applied between B2 and B1.

2. Variable emitter voltage Veis applied across the emitterterminals.

3. If Veis varied , potential of A is decided by η and is equal to ηVbb

Va=Vrb1= ηVbb

Case 1: If Ve< Va

As long as Ve< Va, the pn junction is reverse biased. Hence emitter current I e will not flow.
Thus UJT is said to be off.

Case 2: if Ve>Vp

The diode drop Vd is generally between 0.3 to 0.7v.

We can write Vp=Va+Vd = ηVbb+Vd

When Ve becomes equal to or greater than V p the pn junction becomes forward biased and
current Ie flows. Thus UJT is said to be ON.

VI Characteristics

1.The graph of Ie against emitter voltage plotted for a particular value of V bb is called the
characteristics of UJT.
125

The characteristics can be divided in to three main regions.

1.cutoff 2. Negative resistance region 3. Saturationregion.

1. cut off: The V e< Vp and the pn junction is reverse biased . A small amount of reverse
saturation current Ie0 flows through the device which is negligibly small of the order of micro
amps. This condition remains till the peakpoint.

2. Negative resistance region: When emitter voltage Vebecomes equal to Vp then p n junction
becomes forward biased and Iestarts flowing. The voltage across the device decreases in this
region though the current through the device increases. Hence the region is called negative
resistance region. This decreases the resistance R b1 . This region is stable and used in many
applications. This region continues till valleypoint.

3. Saturation region: The region to the right of the valley point is called saturation region. In
the valley point, the resistance changes from negative to positive. The resistance remains
positive in the saturationregion.

As Vbb increases , the potential Vp corresponding to peak point will increase.

Applications of UJT

The UJT is mainly used in the triggering of other devices such as SCR. It is also used in the
sawtooth wave generators and some timing circuits. The most popular application of UJT is
as a relaxation oscillator to obtain short pulses for triggering ofSCRs.
126

The relaxation oscillator using UJT which is ment for generating sawtooth waveform. It
consists of a UJT and a capacitor , which is charged through emitter resistor as the supply
voltage Vbb is switched 0N.
127

UNIT IV
BIASING AND COMPENSATION TECHNIQUES

NEED FOR TRANSISTORBIASING:

If the o/p signal must be a faithful reproduction of the i/p signal, the transistor must be
operated in active region. That means an operating point has to be established in this region .
To establish an operating point (proper values of collector current Icand collector to emitter
voltage VCE) appropriate supply voltages and resistances must be suitably chosen in the ckt. This
process of selecting proper supply voltages and resistance for obtaining desired operating point
or Q point is called as biasing and the ckt used for transistor biasing is called as biasingckt.

There are four conditions to be met by a transistor so that it acts as a faithful ampr:

1) Emitter base junction must be forward biased (VBE=0.7Vfor Si, 0.2V for Ge) and collector
base junction must be reverse biased for all levels of i/psignal.
2) Vce voltage should not fall below VCE(sat) (0.3V for Si, 0.1V for Ge) for any part of the i/p
signal.ForVCElessthanVCE(sat)thecollectorbasejunctionisnotprobablyreversebiased.
3) The value of the signal Ic when no signal is applied should be at least equal to the max.
collector current t due to signalalone.
4) Max. rating of the transistor Ic(max), VCE(max) and PD(max) should not be exceeded at any
value of i/p signal.

Consider the fig shown in fig1. If operating point is selected at A, A represents a condition
when no bias is applied to the transistor i.e, I c=0, VCE =0. It does not satisfy the above said
conditions necessary for faithful amplification.

Point C is too close to P D(max) curve of the transistor. Therefore the o/p voltage swing in the
positive direction is limited.

Point B is located in the middle of active region .It will allow both positive and negative half
cycles in the o/p signal. It also provides linear gain and larger possible o/p voltages and currents

Hence operating point for a transistor amplifier is selected to be in the middle of active
region.
128

IC(max)

PD(max)

Vce(sat)
fig1

DC LOADLINE:

Referring to the biasing circuit of fig 4.2a, the values of VCC and RC are fixed and Ic and VCE
are dependent onRB.

Applying Kirchhoff’s voltage law to the collector circuit in fig. 4.2a, we get
129

The straight line represented by AB in fig4.2b is called the dc load line. The coordinates of
the end point A are obtained by substituting V CE =0 in the above equation. Then .

Therefore The coordinates of A are VCE =0 and .

The coordinates of B are obtained by substituting Ic=0 in the above equation. Then Vce =
Vcc. Therefore the coordinates of B are VCE =Vcc and Ic=0. Thus the dc load line AB can be
drawn if the values of Rc and Vcc areknown.

As shown in the fig4.2b, the optimum POINT IS LOCATED AT THE MID POINT OF THE
MIDWAY BETWEEN a AND b. In order to get faithful amplification, the Q point must be well
within the active region of the transistor.

Even though the Q point is fixed properly, it is very important to ensure that the operating
point remains stable where it is originally fixed. If the Q point shifts nearer to either A or B, the
output voltage and current get clipped, thereby o/p signal is distorted.

In practice, the Q-point tends to shift its position due to any or all of the following three
main factors.

1) Reverse saturation current, Ico, which doubles for every 10oC raise intemperature
2) Base emitter Voltage ,VBE, which decreases by 2.5 mV per oC
3) Transistor current gain, hFE or β which increases withtemperature.

If base current IB is kept constant since IBis approximately equal to Vcc/RB. If the transistor
is replaced by another one of the same type, one cannot ensure that the new transistor will
have identical parameters as that of the first one. Parameters such as β vary over a range. This
results in the variation of collector current Ic for a given IB. Hence , in the o/p characteristics,
the spacing between the curves might increase or decrease which leads to the shifting of the Q-
point to a location which might be completelyunsatisfactory.

AC LOADLINE:

Afterdrawingthedcloadline,theoperatingpointQisproperlylocatedatthecenterof the dc
load line. This operating point is chosen under zero input signal condition of the circuit. Hence
the ac load line should also pas through the operating point Q. The effective ac load resistance
Rac, is a combination of RC parallel toRLi.e. || . So the slope of theac
130

load line CQDwillbe . To draw the ac load line, two end points, I.e. VCE(max) and

IC(max) when the signal is applied arerequired.

, which locates point D on theVceaxis.

, which locates the point C on the ICaxis.

By joining points c and D, ac load line CD is constructed. As RC> Rac, The dc load line is less steep
than ac load line.

STABILITY FACTOR(S):

The rise of temperature results in increase in the value of transistor gain β and the
leakage current Ico. So, IC also increases which results in a shift in operating point. Therefore,
The biasing network should be provided with thermal stability. Maintenance of the operating
point is specified by S, which indicates the degree of change in operating point due to change in
temperature.

The extent to which IC is stabilized with varying IC is measured by a stability factor S

ForCEconfiguration

Differentiate the above equation w.r.t IC , Weget


131

S should be small to have better thermal stability.

Stability factor S’ and S’’:

S’ is defined as the rate of change of IC with VBE, keeping IC and VBEconstant.

S’’ is defined as the rate of change of IC with β, keeping ICO and VBEconstant.

METHODS OF TRANSISTORBIASING:

1) Fixed bias (base bias)

This form of biasing is also called base bias. In the fig 4.3 shown, the single power source (for
example, a battery) is used for both collector and base of a transistor, although separate batteries can also be
used.

In the given circuit,

Vcc = IBRB + Vbe

Therefore, IB = (Vcc - Vbe)/RB


132

Since the equation is independent of current ICR, dIB//dICR =0 and the stability factor is given by
the equation….. reduces to

S=1+β

Since β is a large quantity, this is very poor biasing circuit. Therefore in practice the circuit is not
used for biasing.

For a given transistor, Vbe does not vary significantly during use. As Vcc is of fixed value, on selection
of RB, the base current IB is fixed. Therefore this type is called fixed bias type of circuit.

Also for given circuit, Vcc = ICRC + Vce

Therefore, Vce = Vcc - ICRC

Merits:

 Itissimpletoshifttheoperatingpointanywhereintheactiveregionbymerely
changing the base resistor(RB).
 A very small number of components arerequired.

Demerits:

 Thecollectorcurrentdoesnotremainconstantwithvariationintemperature or
power supply voltage. Therefore the operating point isunstable.
 Changes in Vbe will change IB and thus cause RE to change. This in turn will
alter the gain of thestage.
 When the transistor is replaced with another one, considerable change inthe
value of β can be expected. Due to this change the operating point willshift.

2) EMITTER-FEEDBACKBIAS:

The emitter feedback bias circuit is shown in the fig 4.4. The fixed bias circuit is modified
by attaching an external resistor to the emitter. This resistor introduces negative feedback that
stabilizes the Q-point. From Kirchhoff's voltage law, the voltage across the base resistor is

VRb = VCC - IeRe - Vbe.


133

From Ohm's law, the base current is

Ib = VRb / Rb.

The way feedback controls the bias point is as follows. If Vbe is held constant and
temperature increases, emitter current increases. However, a larger I e increases the emitter
voltage Ve = IeRe, which in turn reduces the voltage VRb across the base resistor. A lower base-
resistor voltage drop reduces the base current, which results in less collector current because I c
= ß IB. Collector current and emitter current are related by I c = α Ie with α ≈ 1, so increase in
emitter current with temperature is opposed, and operating point is kept stable.

Similarly, if the transistor is replaced by another, there may be a change in I C


(corresponding to change in β-value, for example). By similar process as above, the change is
negated and operating point kept stable.

For the given circuit,

IB = (VCC - Vbe)/(RB + (β+1)RE).

Merits:

The circuit has the tendency to stabilize operating point against changes in temperature
and β-value.

Demerits:

 In this circuit, to keep IC independent of β the following condition must bemet:


134

which is approximately the case if ( β + 1 )RE>> RB.

 Asβ-valueisfixedforagiventransistor,thisrelationcan besatisfiedeitherby
keeping RE very large, or making RB verylow.

 If RE is of large value, high VCC is necessary. This increases cost as well


as precautions necessary whilehandling.
 If RB is low, a separate low voltage supply should be used in the basecircuit.
Using two supplies of different voltages isimpractical.

 In addition to the above, RE causes ac feedback which reduces the voltage gainof
theamplifier.

3) COLLECTOR TO BASE BIAS OR COLLECTOR FEED-BACK BIAS:

This configuration shown in fig 4.5 employs negative feedback to prevent thermal
runaway and stabilize the operating point. In this form of biasing, the base resistor RB is
connected to the collector instead of connecting it to the DC source Vcc. So any thermal
runaway will induce a voltage drop across the RC resistor that will throttle the transistor's base
current.

From Kirchhoff's voltage law, the voltage across the base resistor Rbis
135

By the Ebers–Moll model, Ic = βIb, and so

From Ohm's law, the base current , andso

Hence, the base current Ib is

If Vbe is held constant and temperature increases, then the collector current Ic increases.
However, a larger Ic causes the voltage drop across resistor Rc to increase, which in turn
reduces the voltage across the base resistor Rb. A lower base-resistor voltage drop reduces
the base current Ib, which results in less collector current Ic. Because an increase in collector
current with temperature is opposed, the operating point is keptstable.

Merits:

 Circuit stabilizes the operating point against variations in temperature and β(i.e.
replacement oftransistor)

Demerits:

 In this circuit, to keep Ic independent of β, the following condition must bemet:

which is the case when

 As β-value is fixed (and generally unknown) for a given transistor, this relation
can be satisfied either by keeping Rc fairly large or making Rb verylow.
136

 If Rc is large, a high Vcc is necessary, which increases cost as well as precautions


necessary whilehandling.
 If Rb is low, the reverse bias of the collector–base region is small, which limits the
range of collector voltage swing that leaves the transistor in activemode.

 The resistor Rb causes an AC feedback, reducing thevoltage gainof the amplifier.


This undesirable effect is a trade-off for greaterQ-pointstability.

Usage: The feedback also decreases the input impedance of the amplifier as seen from
the base, which can be advantageous. Due to the gain reduction from feedback, this biasing
form is used only when the trade-off for stability is warranted.

4) COLLECTOR –EMITTER FEEDBACKBIAS:

The above fig4.6 shows the collector –emitter feedback bias circuit that can be obtained
by applying both the collector feedback and emitter feedback. Here the collector feedback is
provided by connecting a resistance RB from the collector to the base and emitter feedback is
provided by connecting an emitter Re from emitter to ground. Both feed backs are used to
137

control collector current and base current IB in the opposite direction to increase the stability
as compared to the previous biasingcircuits.

5) VOLTAGE DIVIDER BIAS OR SELF BIAS OR EMITTERBIAS:

The voltage divider as shown in the fig 4.7 is formed using external resistors R 1 and R2.
The voltage across R2 forward biases the emitter junction. By proper selection of resistors
R1and R2, the operating point of the transistor can be made independent of β. In this circuit, the
voltage divider holds the base voltage fixed independent of base current provided the divider
current is large compared to the base current. However, even with a fixed base voltage,
collector current varies with temperature (for example) so an emitter resistor is added to
stabilize the Q-point, similar to the above circuits with emitterresistor.

In this circuit the base voltage is given by:

voltageacross

provided .

Also
138

For the given circuit,

Let the current in resistor R1 is I1 and this is divided into two parts – current through
base and resistor R2. Since the base current is very small so for all practical purpose it is
assumed that I1 also flows through R2, so we have

Applying KVL in the circuit, we have

It is apparent from above expression that the collector current is independent of ? thus
the stability is excellent. In all practical cases the value of VBE is quite small in comparison to
the V2, so it can be ignored in the above expression so the collector current is almost
independent of the transistor parameters thus this arrangement provides excellentstability.
Again applying KVL in collector circuit, we have

The resistor RE provides stability to the circuit. If the current through the collector rises,
the voltage across the resistor RE also rises. This will cause VCE to increase as the voltage V2 is
independent of collector current. This decreases the base current, thus collector current
increases to its former value.
Stability factor for such circuit arrangement is given by
139

If Req/RE is very small compared to 1, it can be ignored in the above expression thus we
have

Which is excellent since it is the smallest possible value for the stability. In actual
practice the value of stability factor is around 8-10, since Req/RE cannot be ignored as
compared to 1.

Merits:

 Unlike above circuits, only one dc supply isnecessary.


 Operating point is almost independent of β variation.
 Operating point stabilized against shift intemperature.

Demerits:

 In this circuit, to keep IC independent of β the following condition must bemet:

which is approximately the caseif

where R1 || R2 denotes the equivalent resistance of R1 and R2 connected in parallel.

 As β-value is fixed for a given transistor, this relation can be satisfied either by
keeping RE fairly large, or making R1||R2 very low.

 If RE is of large value, high VCC is necessary. This increases cost as well as


precautions necessary whilehandling.
 If R1 || R2 is low, either R1 is low, or R2 is low, or both are low. A low R1 raises V B
closer to VC, reducing the available swing in collector voltage, and limiting how large RCcan be
made without driving the transistor out of active mode. A low R2lowers Vbe, reducingthe
140

allowed collector current. Lowering both resistor values draws more current from the power
supply and lowers the input resistance of the amplifier as seen from the base.

 AC as well as DC feedback is caused by RE, which reduces the AC voltage gain of


the amplifier. A method to avoid AC feedback while retaining DC feedback is discussedbelow.

Usage: The circuit's stability and merits as above make it widely used for linear circuits.

BIAS COMPENSATION USING DIODE ANDTRANSISTOR:

The various biasing circuits considered use some type of negative feedback to stabilize
the operation point. Also, diodes, thermistors and sensistors can be used to compensate for
variations in current.

DIODE COMPENSATION:

The following fig4.8 shows a transistor amplifier with a diode D connected across the
base-emitter junction for compensation of change in collector saturation current I CO. The diode
is of the same material as the transistor and it is reverse biased by e the emitter-base junction
141

voltage VBE, allowing the diode reverse saturation current I O to flow through diode D. The base
current IB=I-IO.

As long as temperature is constant, diode D operates as a resistor. As the temperature


increases, ICO of the transistor increases. Hence, to compensate for this, the base current I B
should be decreased.

The increase in temperature will also cause the leakage current I O through D to increase
and thereby decrease the base current IB. This is the required action to keep Ic constant.

This type of bias compensation does not need a change in Ic to effect the change in I C, as
both IO and ICO can track almost equally according to the change in temperature.

THERMISTOR COMPENSATION:

The following fig4.9 a thermistor R T, having a negative temperature coefficient is


connected in parallel with R2. The resistance of thermistor decreases exponentially with
increase of temperature. An increase of temperature will decrease the base voltage VBE,
reducing IB andIC.

SENSISTOR COMPENSATION:

In the following fig4.10 shown a sensistor Rs having a positive temperature coefficient is


connected across R1 or RE. Rs increases with temperature. As the temperature increases, the
equivalent resistance of the parallel combination of R1 and Rs also increases and hence V BE
142

decreases, reducing IB and Ic. This reduced Ic compensates for increased Ic caused by the
increase in VBE, ICO and β due to temperature.

THERMAL RUNAWAY AND THERMALSTABILITY:

THERMAL RUNAWAY:

The collector current for the CE circuit is given by The three


variables in the equation, β, , and increases with rise in temperature. In particular, the
reverse saturation current or leakage current changes greatly with temperature. Specifically
itdoublesforevery10oCriseintemperature.Thecollectorcurrentcausesthecollectorbase
junction temperature to rise which in turn, increase , as a result will increase still further,
which will further rise the temperature at the collector base junction. This process will become
cumulative leading at the collector base junction. This process will become cumulative leading
to “thermal runaway”. Consequently, the ratings of the transistor are exceeded which may
destroy the transistoritself.

The collector is made larger in size than the emitter in order to help the heat developed
at the collector junction. However if the circuit is designed such that the base current is
made to decrease automatically with rise in temperature, then the decrease in will
compensate for increaseinthe , keeping almostconstant.
143

THERMAL RESISTANCE

Consider transistor used in a circuit where the ambient temperature of the air around
the transistor is TAoC and the temperature of the collector-base junction of the transistor is TJoC.

Due to heating within the transistor TJ is higher than TA. As the temperature difference TJ- TA is
greater,thepowerdissipatedinthetransistor,PDwillbegreater,i.e,TJ-TA PD

The equation can be written as TJ- TA PD. , where is the constant of proportionality
and is called the Thermal resistance. Rearranging the above equation = TJ- TA /PD. Hence is
measured in oC/W which may be as small as 0.2 oC/W for a high power transistor that has an
efficient heat sink or up to 1000oC/W for small signal, low power transistor which have no
coolingprovision.

As Θ represents total thermal resistance from a transistor junction to the ambient


temperature, it is referred to as ΘJ-A. However, for power transistors, thermal resistance is
given form junction to case,ΘJ-C.

The amount resistance from junction to ambience is considered to consist of 2 parts.

ΘJ-A = ΘJ-C - ΘC-A.

Which indicates the heat dissipated in the junction must make its way to the surrounding air
through two series paths from junction to case and from case to air. Hence the power
dissipated.

PD=(TJ-TA ΘJ-A

=(TJ-TA ΘJ-C +ΘC-A)

ΘJ-C is determined by the type of manufacture of the transistor and how it is located I the case,
but ΘC-A is determined by the surface area of the case or flange and its contact with air. If the
effective surface area of the transistor case could be increased, the resistance to heat flows, or
could be increased ΘC-A, could be decreased. This can be achieved by the use of a heat sink.

The heat sink is a relatively large, finned, usually black metallic heat conducting device in
close contact with transistor case or flange. Many versions of heat sink exist depending upon
the shape and size of the transistor. Larger the heat sink smaller is the thermal resistance ΘHS-A.

This thermal resistance is not added to ΘC-A in series, but is instead in parallel with it and if
144

ΘHS-A is much less than ΘC-A, then ΘC-A will be reduced significantly, thereby improving the
dissipation capability of the transistor. Thus

ΘJ-A =ΘJ-C+ΘC-A||ΘHS-A.

CONDITION FOR THERMALSTABILITY:


For preventing thermal runaway, the required condition I the rate at which the heat is released
at the collector junction should not exceed the rate at which the heat can be dissipated under steady
state condition. Hence the condition to be satisfied to avoid thermal runaway is given by

If the circuit is properly designed, then the transistor cannot runaway below a specified ambient
temperature or even under any conditions.

In the self biased circuit the transistor is biased in the active region. The power generated at the
junction without any signal is

Let us assume that the quiescent collector and the emitter currents are equal. Then

………………….(1)

The condition to prevent thermal runaway can be writtenas

As Θ and are positive, should be negative in order to satisfy the above condition.

Differentiating equation (1) w.r.t weget

Hence to avoid thermal runaway it is necessary that


145

SinceVCE=VCC-IC(RE+RC) then eq(4) implies that VCE<VCC/2. IF the inequality of eq(4) is not
satisfied and VCE<VCC/2, then from eq(3), is positive., and the corresponding eq(2) should
be satisfied. Other wise thermal runaway willoccur.

BIASING FET:-
For the proper functioning of a linear FET amplifier, it is necessary to maintain the
operating point Q stable in the central portion of the pinch off region The Q point should be
independent of device parameter variations and ambient temperature variations

This can be achieved by suitably selecting the gate to source voltage VGS and drain current I D which is
referred to as biasing

JFET biasing circuits are very similar to BJT biasing circuitsThe main difference between
JFET circuits and BJT circuits is the operation of the active components themselves

There are mainly two types of Biasing circuits

1) Selfbias
2) Voltage dividerbias.

SELFBIAS
Self bias is a JFET biasing circuit that uses a source resistor to help reverse bias the JFET gate. A self
bias circuit is shown in the fig. Self bias is the most common type of JFET bias. This JFET must be
operated such that gate source junction is always reverse biased. This condition requires a negative VGS
for an N channel JFET and a positive VGS for P channel JFET. This can be achieved using the self bias
arrangement as shown in Fig. The gate resistor RG doesn’t affect the bias because it has essentially no
voltage drop across it, and : the gate remains at 0V .RG is necessary only to isolate an ac signal from
ground in amplifier applications. The voltage drop across resistor RS makes gate source junction reverse
biased.
146

For the dc analysis coupling capacitors are open circuits.

For the N channel FET in Fig (a)

IS produces a voltage drop across RS and makes the source positive w.r.t ground. In any JFET circuit all
the source current passes through the device to the drain circuit .This is due to the fact that there is no
significant gatecurrent.

We can define source current as IS =ID

(VG =0 because there is no gate current flowing in RG So VG across RG is zero)

VG =0 then VS= ISRS =IDRS

VGS = VG-VS =0-ID RS=- ID RS

DC analysis of self Bias:-

In the following DC analysis, the N channel J FET shown in the fig. is used for illustration.

For DC analysis we can replace coupling capacitors by open circuits and we can also replace the resistor
RG by a short circuit equivalent.:. IG = 0.The relation between ID and VGS is given by

Id=Idss[1- ]2

VGS for N channel JFET is =-id Rs

Substuting this value in the above equation

Id=Idss[1- ]2

Id=Idss[1+ ]2

For the N-chanel FET in the above figure


147

Is produces a voltage drop across Rs and makes the source positive w.r.t ground in any JFET circuit all the

sourcecurrent passesthroughthedevicetodraincircuitthisisduetothefactthatthereisnosignificant gate current.

Therefore we can define source current as Is=Id and Vg=0then

Vs= Is Rs =IdRs

Vgs=Vg-Vs=0-IdRs=-IdRs

Drawing the self biasline:-

Typical transfer characteristics for a self biased JFET are shown in the fig.

The maximum drain current is 6mA and the gate source cut off voltage is -3V. This means the gate
voltage has to be between 0 and -3V.

Now using the equation VGS = -IDRS and assuming RS of any suitable value we can draw the self bias line.

Let us assume RS = 500Ω

With this Rs , we can plot two points corresponding to I D = 0 and Id = IDSS

for ID = 0

VGS = -ID RS

VGS = 0X (500.Ω) = 0V

So the first point is (0 ,0)


148

( Id, VGS)

For ID= IDSS=6mA

VGS = (-6mA) (500 Ω) = -3V

So the 2nd Point will be (6mA,-3V)

By plotting these two points, we can draw the straight line through the points. This line will
intersect the transconductance curve and it is known as self bias line.The intersection point gives the
operating point of the self bias JFET for the circuit.

At Q point , the ID is slightly > than 2mA and VGS is slightly > -1V. The Q point for the self bias
JFET depends on the value of Rs.If Rs is large, Q point far down on the transconductance curve ,I D is
small, when Rs is small Q point is far up on the curve , I D is large.

VOLTAGE DIVIDERBIAS:-

The fig. shows N channel JFET with voltage divider bias. The voltage at the source of JFET must
be more positive than the voltage at the gate in order to keep the gate to source junction reverse
biased. The source voltageis

VS = IDRS

The gate voltage is set by resistors R1 and R2 as expressed by the following equation using the
voltage divider formula.

Vg= Vdd

For dc analysis
149

Applying KVL to the input circuit

VG-VGS-VS =0

:: VGS = VG-Vs=VG-ISRS

VGS=VG-IDRS :: IS =ID

Applying KVL to the input circuit we get

VDS+IDRD+VS-VDD =0

::VDS = VDD-IDRD-IDRS

VDS = VDD-ID ( RD +RS )

The Q point of a JFET amplifier , using the voltage divider biasis

IDQ = IDSS[1-VGS/VP]2

VDSQ = VDD-ID ( RD+RS)


150

UNIT V

BJT AND FET AMPLIFIERS

5.0 Introduction

characteristics of an active device such as BJT are non-linear. The analysis of a non-
linear device is complex. Thus to simplify the analysis of the BJT, its operation is
restricted to the linear V-I characteristics around the Q-point i.e. in the active region.
This approximation ispossible only with small input signals. With small input signals
transistor can be replaced with small signal linear model. This model is also called small
signal equivalentcircuit.

5..1Two –Port Devices and Network Parameters

Small signal low frequency transistor Models:

All the transistor amplifiers are two port networks having two voltages and two currents. The
positive directions of voltages and currents are shown in fig. 1.

Fig. 1

A two-port network is represented by four external variables: voltage V1 and current I1 at the
input port, and voltage V2 and current I2 at the output port, so that the two-port network can be
treated as a black box modeled by the relationships between the four variables,V 1,V2, I1,I2 . Out of
four variables two can be selected as are independent variables and two are dependent
variables.The dependent variables can be expressed interns of independent variables. This leads to
various two port parameters out of which the following three areimportant:

1. Impedance parameters (z-parameters)


2. Admittance parameters (y-parameters)
3. Hybrid parameters(h-parameters)
151

z-parameters
A two-port network can be described by z-parameters as

In matrix form, the above equation can be rewritten as

Where

Input impedance with output port open circuited

Reverse transfer impedance with input port open circuited

Forward transfer impedance with output port open circuited

Output impedance with input port open circuited

Y-parameters

A two-port network can be described by Y-parameters as


152

In matrix form, the above equation can be rewritten as

Input admittance with output port short circuited

Reverse transfer admittance with input port short circuited

Forward transfer admittance with output port short circuited

Output admittance with input port short circuited

Hybrid parameters(h-parameters)

If the input current I1 and output voltage V2 are taken as independent variables, the dependent
variables V1 and I2 can be written as

Where h11, h12, h21, h22 are called as hybrid parameters.


153

Input impedence with o/p port short circuited

Reverse voltage transfer ratio with i/p port open circuited

Forward voltage transfer ratio with o/p port short circuited

output impedence with i/p port open circuited

THE HYBRID MODEL FOR TWO PORTNETWORK:


Based on the definition of hybrid parameters the mathematical model for two pert networks
known as h-parameter model can be developed. The hybrid equations can be written as:

(The following convenient alternative subscript notation is recommended


by the IEEE Standards:
i=11=input o = 22 =output

f =21 = forward transfer r = 12 = reverse transfer)

We may now use the four h parameters to construct a mathematical model of the device of
Fig.(1). The hybrid circuit for any device indicated in Fig.(2). We can verify that the model of
Fig.(2) satisfies above equations by writing Kirchhoff'svoltage and current laws for inputand
154

output ports.

If these parameters are specified for a particular configuration, then suffixes e,b or c are also
included, e.g. hfe ,h ib are h parameters of common emitter and common collector amplifiers

Using two equations the generalized model of the amplifier can be drawn as shown in fig. 2.

Fig. 2

5.2.1 TRANSISTOR HYBRID MODEL:


The hybrid model for a transistor amplifier can be derived as follow:

Let us consider CE configuration as show in fig. 3. The variables, iB, iC ,vC, and vB represent total
instantaneous currents and voltages iB and vC can be taken as independent variables and vB, IC as
dependent variables.
155

Fig. 3

VB = f1 (iB ,vC )

IC = f2 (iB ,vC).

Using Taylor 's series expression, and neglecting higher order terms we obtain.

The partial derivatives are taken keeping the collector voltage or base current constant. The Δ vB,
Δ vC, Δ iB, Δ iC represent the small signal (incremental) base and collector current and voltage and
can be represented as vB, iC, iB ,vC
156

The model for CE configuration is shown in fig. 4.

Fig. 4

To determine the four h-parameters of transistor amplifier, input and output characteristic are
used. Input characteristic depicts the relationship between input voltage and input current with
output voltage as parameter. The output characteristic depicts the relationship between output
voltage and output current with input current as parameter. Fig. 5, shows the output
characteristics of CE amplifier.

Fig. 5

The current increments are taken around the quiescent point Q which corresponds to iB = IB and
to the collector voltage VCE = VC

The value of hoe at the quiescent operating point is given by the slope of the output characteristic
at the operating point (i.e. slope of tangent AB).
157

hie is the slope of the appropriate input on fig. 6, at the operating point (slope of tangent EF at Q).

Fig. 6

A vertical line on the input characteristic represents constant base current. The parameter hre can
be obtained from the ratio (VB2– V B1 ) and (VC2– V C1 ) for at Q.

Typical CE h-parametersof transistor 2N1573 are given below:

hie = 1000 ohm.


hre = 2.5 * 10 –4
hfe = 50
hoe=25 A /V

ANALYSIS OF A TRANSISTOR AMPLIFIER USING H-


PARAMETERS:
To form a transistor amplifier it is only necessary to connect an external load and signal source
as indicated in fig. 1and to bias the transistor properly.
158

Fig. 1

Consider the two-port network of CE amplifier. RS is the source resistance and ZL is the load
impedence h-parameters are assumed to be constant over the operating range. The ac equivalent
circuit is shown in fig. 2. (Phasor notations are used assuming sinusoidal voltage input). The
quantities of interest are the current gain, input impedence, voltage gain, and output impedence.

Fig. 2

Currentgain:
For the transistor amplifier stage, Ai is defined as the ratio of output to input currents.

Inputimpedence:
159

The impedence looking into the amplifier input terminals ( 1,1' ) is the input impedence Z i

Voltagegain:
The ratio of output voltage to input voltage gives the gain of the transistors.

OutputAdmittance:
It is defined as
160

Av is the voltage gain for an ideal voltage source (Rv = 0).

Consider input source to be a current source I S in parallel with a resistance RS as shown in fig. 3.

Fig. 3

In this case, overall current gain AIS is defined as


161

h-parameters
To analyze multistage amplifier the h-parameters of the transistor used are obtained from
manufacture data sheet. The manufacture data sheet usually provides h-parameter in CE
configuration. These parameters may be converted into CC and CB values. For example
fig.4hrc in terms of CE parameter can be obtained as follows.

Fig. 4

For CE transistor configuaration

Vbe = hie Ib + hre Vce

Ic = h fe Ib + hoe Vce

The circuit can be redrawn like CC transistor configuration as shown in fig. 5.

Vbc = hie Ib + hrc Vec

Ic = hfe Ib + hoe Vec


162

hybrid model for transistor in three different configurations

Typical h-parameter values for a transistor


Parameter CE CC CB
hi 1100 Ω 1100 Ω 22 Ω
hr 2.5 × 10-4 1 3 × 10-4
hf 50 -51 -0.98
ho 25 µA/V 25 µA/V 0.49 µA/V

Analysis of a Transistor amplifier circuit using h-parameters


163

A transistor amplifier can be constructed by connecting an external load and signal


source and biasing the transistor properly.

Fig.1.4 Basic Amplifier Circuit

The two port network of Fig. 1.4 represents a transistor in any one of its configuration. It
is assumed that h-parameters remain constant over the operating range.The input is sinusoidal
and I1,V1,I2 and V2 are phase quantities

Fig. 1.5 Transistor replaced by its Hybrid Model

Current Gain or Current Amplification (Ai)

For transistor amplifier the current gain Ai is defined as the ratio of output current to input
current,i.e,
Ai =IL /I1 = -I2 / I1
From the circuit ofFig
I2= hfI1+hoV2
164

Substituting V2 = ILZL = -I2ZL

I2= hf I1- I2ZLho

I2 + I2ZL ho = hf I1

I2( 1+ ZLho) = hf I1

Ai = -I2 / I1 = - hf / ( 1+ ZLho)

Therefore,

Ai = - hf / ( 1+ ZLho)

Input Impedence (Zi)

In the circuitofFig , RSis the signal source resistance .The impedence seen when looking into
the amplifier terminals (1,1’) is the amplifier input impedenceZi,

Zi = V1 / I1

From the input circuit of Fig V1 = hi I1 + hrV2

Zi = ( hi I1 + hrV2) / I1

= hi + hr V2 / I1

Substituting

V2 = -I2 ZL = A1I1ZL

Zi = hi + hr A1I1ZL / I1

= hi + hr A1ZL

Substituting for Ai

Zi = hi - hf hr ZL / (1+ hoZL)

= hi - hf hr ZL / ZL(1/ZL+ ho)
165

Taking the Load admittance as YL =1/ ZL

Zi = hi - hf hr / (YL + ho)

Voltage Gain or Voltage Gain Amplification Factor(Av)

The ratio of output voltage V2 to input voltage V1 give the voltage gain of the transistor i.e,

Av = V2 / V1

Substituting

V2 = -I2 ZL = A1I1ZL

Av = A1I1ZL / V1 = AiZL / Zi

Output Admittance (Yo)

Yo is obtained by setting VS to zero, ZL to infinity and by driving the output terminals from a
generator V2. If the current V2 is I2 then Yo= I2/V2 with VS=0 and RL= ∞.

From the circuit of fig

I2= hf I1 + hoV2

Dividing by V2,

I2 / V2 = hf I1/V2 + ho

With V2= 0, by KVL in input circuit,

RSI1 + hi I1 + hrV2 = 0

(RS + hi) I1 + hrV2 = 0

Hence, I2 / V2= -hr / (RS +hi)

= hf (-hr/( RS + hi)+ho

Yo= ho- hf hr/( RS + hi)


166

The output admittance is a function of source resistance. If the source impedence is resistive then
Yo is real.

Voltage Amplification Factor(Avs) taking into account the resistance (Rs) of the source

Fig. 5.6 Thevenin’s Equivalent Input Circuit

This overall voltage gain Avs is given by

Avs = V2 / VS = V2V1 / V1VS = Av V1/ VS

From the equivalent input circuit using Thevenin’s equivalent for the source shown in Fig. 5.6

V1 = VS Zi / (Zi+ RS)

V1 / VS = Zi / ( Zi + RS)

Then, Avs =Av Zi / ( Zi + RS)

Substituting Av = AiZL /Zi

Avs = AiZL / ( Zi + RS)

Avs = AiZL RS / ( Zi + RS) RS

Avs = AisZL / RS

Current Amplification (Ais) taking into account the sourse Resistance(RS)


167

Fig. 1.7 Norton’s Equivalent Input Circuit

The modified input circuit using Norton’s equivalent circuit for the calculation of Ais is shown in
Fig. 1.7
OverallCurrentGain,Ais=-I2/ IS=-I2I1/I1IS=Ai I1/IS
FromFig.1.7 I1= IS RS / (RS +Zi)
I1 / IS = RS / (RS + Zi)
andhence, Ais = AiRS / (RS +Zi)

Operating Power Gain (AP)


The operating power gain APof the transistor is definedas
AP = P2 / P1 = -V2 I2 / V1 I1 = AvAi= AiAiZL/ Zi AP
= A 2(Zi / Z)
L i

Small Signal analysis of a transistor amplifier


Ai = - hf / ( 1+ ZLho) Av = AiZL / Zi

Zi = hi + hr A1ZL = hi - hf hr / (YL + ho) Avs = Av Zi / ( Zi + RS) = AiZL / ( Zi + RS)


= AisZL / RS

Yo= ho- hf hr/( RS + hi) = 1/ Zo Ais = Ai RS / (RS + Zi) = Avs = Ais RS/ ZL
168

Simplified common emitter hybrid model:

In most practical cases it is appropriate to obtain approximate values of A V , A i etc rather than
calculating exact values. How the circuit can be modified without greatly reducing the accuracy.
Fig. 4shows the CE amplifier equivalent circuit in terms of h-parameters Since 1 / hoe in parallel
with RL is approximately equal to RL if 1 / hoe>> RL then hoe may be neglected. Under these
conditions.

Ic = hfe IB .

hre vc = hre Ic RL = hre hfe Ib RL .

Fig. 4

Since h fe.h re = 0.01(approximately), this voltage may be neglected in comparison with h ic Ib


drop across h ie provided RL is not very large. If load resistance RL is small than hoe and hre can
be neglected.

Output impedence seems to be infinite. When Vs = 0, and an external voltage is applied at the
output we fined Ib = 0, I C = 0. True value depends upon RS and lies between 40 K and 80K.

On the same lines, the calculations for CC and CB can be done.

CE amplifier with an emitter resistor:

The voltage gain of a CE stage depends upon hfe. This transistor parameter depends upon
temperature, aging and the operating point. Moreover, h fe may vary widely from device to
device, even for same type of transistor. To stabilize voltage gain A V of each stage, it should be
169

independent of hfe. A simple and effective way is to connect an emitter resistor Re as shown in
fig. 5. The resistor provides negative feedback and provide stabilization.

Fig. 5

An approximate analysis of the circuit can be made using the simplified model.
170

Subject to above approximation A V is completely stable. The output resistance is infinite for the
approximatemodel.

Comparison of Transistor Amplifier Configuration

The characteristics of three configurations are summarized in Table .Here the quantities
Ai,Av,Ri,Ro and AP are calculated for a typical transistor whose h-parameters are given in table
.The values of RL and Rs are taken as 3KΩ.

Table: Performance schedule of three transistor configurations

Quantity CB CC CE
AI 0.98 47.5 -46.5
AV 131 0.989 -131
AP 128.38 46.98 6091.5
Ri 22.6 Ω 144 kΩ 1065 Ω
Ro 1.72 MΩ 80.5 Ω 45.5 kΩ

The values of current gain, voltage gain, input impedance and output impedance
calculated as a function of load and source impedances

Characteristics of Common Base Amplifier

(i) Current gain is less than unity and its magnitude decreases with the increase ofload
resistance RL,
(ii) Voltage gain AVis high for normal values ofRL,
(iii) The input resistance Riis the lowest of all the three configurations,and
(iv) The output resistance Ro is the highest of all the threeconfigurations.

Applications The CB amplifier is not commonly used for amplification purpose. It is used for

(i) Matching a very low impedancesource


(ii) As a non inverting amplifier to voltage gain exceedingunity.
171

(iii) For driving a high impedanceload.


(iv) As a constant currentsource.

Characteristics of Common Collector Amplifier

(i) For low RL(< 10 kΩ), the current gain Aiis high and almost equal to that of aCE
amplifier.
(ii) The voltage gain AVis less thanunity.
(iii) The input resistance is the highest of all the threeconfigurations.
(iv) The output resistance is the lowest of all the threeconfigurations.

Applications The CC amplifier is widely used as a buffer stage between a high impedance source
and a low impedance load.

Characteristics of Common Emitter Amplifier

(i) The current gain Aiis high for RL< 10kΩ.


(ii) The voltage gain is high for normal values of load resistanceR L.
(iii) The input resistance Riismedium.
(iv) The output resistance Ro is moderatelyhigh.

Applications: CE amplifier is widely used for amplification.

Simplified common emitter hybrid model:

In most practical cases it is appropriate to obtain approximate values of A V , A i etc rather than
calculating exact values. How the circuit can be modified without greatly reducing the accuracy.
Fig 1. 8shows the CE amplifier equivalent circuit in terms of h-parameters Since 1 / hoe in
parallel with RL is approximately equal to RL if 1 / hoe>> RL then hoe may be neglected. Under
these conditions.

Ic = hfe IB .

hre vc = hre Ic RL = hre hfe Ib RL .


172

Fig 1.8

Since h fe.h re » 0.01, this voltage may be neglected in comparison with h ic Ib drop across h ie
provided RL is not very large. If load resistance R L is small than hoe and hre can be neglected.

Output impedence seems to be infinite. When Vs = 0, and an external voltage is applied at the
output we fined Ib = 0, I C = 0. True value depends upon RS and lies between 40 K and 80K.

On the same lines, the calculations for CC and CB can be done.

CE amplifier with an emitter resistor:

The voltage gain of a CE stage depends upon hfe. This transistor parameter depends upon
temperature, aging and the operating point. Moreover, hfe may vary widely from device to
device, even for same type of transistor. To stabilize voltage gain A V of each stage, it should be
independent of hfe. A simple and effective way is to connect an emitter resistor R e as shown in
fig.1.9. The resistor provides negative feedback and provide stabilization.
173

Fig.1.9

An approximate analysis of the circuit can be made using the simplified model.

Subject to above approximation A V is completely stable. The output resistance is infinite for the
approximate model.
174

Common Base Amplifier:

The common base amplifier circuit is


shown in Fig. 1. The VEE source
forward biases the emitter diode and
VCC source reverse biased collector
diode. The ac source vinis connected to
emitter through a couplingcapacitor so
that it blocks dc. This ac voltage
produces small fluctuation in currents
and voltages. The load resistance RL is
also connected to collector through
coupling capacitor so the fluctuation
in collector base voltage will be
observed acrossRL.

The dc equivalent circuit is obtained


by reducing all ac sources to zero and
opening all capacitors. The dc
collector current is same as IE and VCB Fig. 1
is given by

VCB = VCC - IC RC.

These current and voltage fix the Q point. The ac equivalent circuit is obtained by reducing all dc
sources to zero and shorting all coupling capacitors. r'e represents the ac resistance of the diode
as shown in Fig.2.

Fig. 2

Fig. 3, shows the diode curve relating IE and VBE. In the absence of ac signal, the transistor
operates at Q point (point of intersection of load line and input characteristic). When the ac
175

signal is applied, the emitter current and voltage also change. If the signal is small, the operating
point swings sinusoidally about Q point (A to B).

Fig .3

If the ac signal is small, the points A and B are close to Q, and arc A B can be approximated by a
straight line and diode appears to be a resistance given by

If the input signal is small, input voltage and current will be sinusoidal but if the input voltage is
large then current will no longer be sinusoidal because of the non linearity of diode curve. The
emitter current is elongated on the positive half cycle and compressed on negative half cycle.
Therefore the output will also be distorted.

r'e is the ratio of ΔVBE and Δ IE and its value depends upon the location of Q. Higher up the Q
point small will be the value of r' e because the same change in V BE produces large change in IE.
The slope of the curve at Q determines the value of r' e. From calculation it can be proved that.

r'e = 25mV / IE
176

Common BaseAmplifier
Proof:

In general, the current through a diode is given by

Where q is he charge on electron, V is the drop across diode, T is the temperature and K is a
constant.

On differentiating w.r.t V, we get,

The value of (q / KT) at 25°C is approximately 40.

Therefore,

or,

To a close approximation the small changes in collector current equal the small changes in
emitter current. In the ac equivalent circuit, the current ‘iC' is shown upward because if ‘ie'
increases, then ‘iC' also increases in the same direction.

Voltage gain:

Since the ac input voltage source is connected across r'e. Therefore, the ac emitter current is
given by

ie = Vin / r'e
177

or, Vin = ier'e

The output voltage is given by V out = ic (RC || RL)

Under open circuit condition vout = ic Rc

Example-1

Find the voltage gain and output of the amplifier shown in fig. 4, if input voltage is 1.5mV.

Fig. 4

Solution:

The emitter dc current I E is given by

Therefore, emitter ac resistance =

or, AV=56.6
178

and, Vout = 1.5 x 56.6 = 84.9 mV

Example-2

Repeat example-1 if ac source has resistance R s = 100 W .

Solution:

The ac equivalent circuit with ac source resistance is shown in fig. 5.

Fig. 5

The emitter ac current is given by

or,

Therefore, voltage gain of the amplifier =

and, Vout = 1.5 x 8.71 =13.1mV

Small Signal CE Amplifiers:

CE amplifiers are very popular to amplify the small signal ac. After a transistor has been biased
with a Q point near the middle of a dc load line, ac source can be coupled to the base. This
produces fluctuations in the base current and hence in the collector current of the same shape and
frequency. The output will be enlarged sine wave of same frequency.
179

The amplifier is called linear if it does not change the wave shape of the signal. As long as the
input signal is small, the transistor will use only a small part of the load line and the operation
will be linear.

On the other hand, if the input signal is too large. The fluctuations along the load line will drive
the transistor into either saturation or cut off. This clips the peaks of the input and the amplifier is
no longer linear.

The CE amplifier configuration is shown in fig. 1.

Fig. 1

The coupling capacitor (CC ) passes an ac signal from one point to another. At the same time it
does not allow the dc to pass through it. Hence it is also called blocking capacitor.

Fig. 2

For example in fig. 2, the ac voltage at point A is transmitted to point B. For this series reactance
XC should be very small compared to series resistance R S. The circuit to the left of A may be a
source and a series resistor or may be the Thevenin equivalent of a complex circuit. Similarly R L
may be the load resistance or equivalent resistance of a complex network. The current in the loop
is given by
180

As frequencyincreases, decreases, and current increases until it reaches to its


maximum value vin / R. Therefore the capacitor couples the signal properly from A to Bwhen
XC<< R. The size of the coupling capacitor depends upon the lowest frequency to be coupled.
Normally, for lowest frequencyXC 0.1R is taken as designrule.

The coupling capacitor acts like a switch, which is open to dc and shorted for ac.

The bypass capacitor Cbis similar to a coupling capacitor, except that it couples an ungrounded
point to a grounded point. The Cb capacitor looks like a short to an ac signal and therefore
emitter is said ac grounded. A bypass capacitor does not disturb the dc voltage at emitterbecause
it looks open to dc current. As a designrule XCb 0.1RE at Analysis of CEamplifier:

In a transistor amplifier, the dc source sets up quiescent current and voltages. The ac source then
produces fluctuations in these current and voltages. The simplest way to analyze this circuit is to
split the analysis in two parts: dc analysis and ac analysis. One can use superposition theorem for
analysis .

AC & DC Equivalent Circuits:

For dc equivalent circuit, reduce all ac voltage sources to zero and open all ac current sources
and open all capacitors. With this reduced circuit shown in fig. 3dc current and voltages can be
calculated.
181

Fig. 3

For ac equivalent circuits reduce dc voltage sources to zero and open current sources and short
all capacitors. This circuit is used to calculate ac currents and voltage as shown in fig. 4.

Fig. 4

The total current in any branch is the sum of dc and ac currents through that branch. The total
voltage across any branch is the sum of the dc voltage and ac voltage across that branch.

Phase Inversion:

Because of the fluctuation is base current; collector current and collector voltage also swings
above and below the quiescent voltage. The ac output voltage is inverted with respect to the ac
input voltage, meaning it is 180o out of phase with input.

During the positive half cycle base current increase, causing the collector current to increase.
This produces a large voltage drop across the collector resistor; therefore, the voltage output
decreases and negative half cycle of output voltage is obtained. Conversely, on the negative half
cycle of input voltage less collector current flows and the voltage drop across the collector
resistor decreases, and hence collector voltage increases we get the positive half cycle of output
voltage as shown in fig. 5.
182

Fig. 5

lowest frequency.

AC Load line:

Consider the dc equivalent circuit fig. 1.

Fig. 1
183

Assuming IC = IC(approx), the output circuit voltage equation can be written as

The slop of the d.c load lineis .

When considering the ac equivalent circuit, the output impedance becomes R C || RL which is less
than (RC +RE).

In the absence of ac signal, this load line passes through Q point. Therefore ac load line is a line
of slope (-1 / ( RC || RL) ) passing through Q point. Therefore, the output voltage fluctuations
will now be corresponding to ac load line as shown in fig. 2. Under this condition, Q-point is not
in the middle of load line, therefore Q-point is selected slightly upward, means slightly shifted to
saturation side.

Fig. 2

Analysis of CEamplifier

Voltage gain:

To find the voltage gain, consider an unloaded CE amplifier. The ac equivalent circuit is shown in
fig. 3. The transistor can be replaced by its collector equivalent model i.e. a current source and
emitter diode which offers ac resistance r'e.
184

Fig. 3

The input voltage appears directly across the emitter diode.

Therefore emitter current ie = Vin / r'e.

Since, collector current approximately equals emitter current and iC = ie and vout = - ie RC (The
minus sign is used here to indicate phase inversion)

Further vout = - (Vin RC) / r'e

Therefore voltage gain A = vout / vin = -RC / r'e

The ac source driving an amplifier has to supply alternating current to the amplifier. The input
impedance of an amplifier determines how much current the amplifier takes from the ac source.

In a normal frequency range of an amplifier, where all capacitors look like ac shorts and other
reactance are negligible, the ac input impedance is defined as

zin= vin/ iin

Where vin, iin are peak to peak values or rms values

The impedance looking directly into the base is symbolized zin(base) and is given by

Z in(base) = vin / ib ,

Since,v in = ie

r'ezin (base) = r'e.


185

From the ac equivalent circuit, the input impedance zin is the parallel combination of R1 , R2 and
r'e.

Zin = R1||R2 e

The Thevenin voltage appearing at the output is

vout = Avin

The Thevenin impedance is the parallel combination of RCand the internal impedance of the
current source. The collector current source is an ideal source, therefore it has an infinite internal
impedance.

zout = RC.

The simplified ac equivalent circuit is shown in fig. 4.

Analysis of CE amplifier
Example-1:

Select R1 and R2 for maximum output voltage swing in the circuit shown in fig. 5.
186

Fig. 5

Solution:

We first determine ICQ for the circuit

For maximum swing,

V'CC = 2 VCEQ

The quiescent value for VCE is the given by

VCEQ= (3.13 mA) (500 W ) = 1.56 V

The intersection of the ac load line on the vCE axis is V'CC = 3.13V. From the
manufacturer's specification, β for the 2N3904 is 180. RB is set equal to 0.1 βRE. So,

RB = 0.1(180 )(100) = 1.8 K W

VBB = (3.13 x 10-3) (1.1 x 100) + 0.7 = 1.044 V

Since we know VBB and RB, we find R1 and R2,

The maximum output voltage swing, ignoring the non-linearity's at saturation and cutoff,
would then be

The load lines are shown on the characteristics of fig. 6.


187

Fig. 6

The maximum power dissipated by the transistor is calculated to assure that it does not
exceed the specifications. The maximum average power dissipated in the transistor is

P(transistor)= VCEQ ICQ = (1.56 (V)) (3.13 mA) =4.87 mW

This is well within the 350 mW maximum given on the specification sheet. The maximum
conversion efficiency is

The swamped Amplifier:

The ac resistance of the emitter diode r'e equals 25mV / IE and depends on the temperature. Any
change in r'e will change the voltage gain in CE amplifier. In some applications, a change in
voltage is acceptable. But in many applications we need a stable voltage gain is required.

To make it stable, a resistance rE is inserted in series with the emitter and therefore emitter is no
longer ac grounded. fig .7.
188

Fig. 7

Because of this the ac emitter current flows through rE and produces an ac voltage at the emitter.
If rE is much greater than r'e almost all of the ac input signal appears at the emitter, and the
emitter is bootstrapped to the base for ac as well as for dc.

In this case, the collector circuit is given by

Now r'e has a less effect on voltage gain, swamping means rE >> r'e If swamping is less,
voltage gain varies with temperature. If swamping is heavy, then gain reduces very much.

Design of Amplifier :

Example -1 (Common Emitter Amplifier Design)


189

Design a common-emitter amplifier with a transistor having a β =200 and VBE = 0.7 V. Obtain
an overall gain of |A V | ≥ 100 and maximum output voltage swing. Use the CE configuration
shown in fig. 1with two power supplies. Rsource is the resistance associated with the source,
vsource. Let Rsource= 100 Ohms. The output load is 2KΩ. Determine the resistor values of the
bias circuitry, the maximum undistorted output voltage swing, and the stage voltage gain.

Fig. 1

Solution:

The maximum voltage across the amplifier is 10 V since the power supply can be visualized as a
10V power supply with a ground in the center. In this case, the ground has no significance to the
operation of the amplifier since the input and output are isolated from the power supplies by
capacitors.

We will have to select the value for RC and we are really not given enough information to do so.
Let choose RC = Rload.

We don't have enough information to solve for RB – we can't use the bias stability criterion since
we don't have the value of RE either. We will have to (arbitrarily) select a value of RB or RE. If
this leads to a contradiction, or “bad” component values (e.g., unobtainable resistor values), we
can come back and modify our choice. Let us select a value for RE that is large enough to obtain a
reasonable value of VBB, Selecting RE as 400Ω will not appreciably reduce the collector current
yet it will help in maintaining a reasonable value of VBB. Thus,

RB = 0.1 β RE = 0.1 (200)(400) = 8 K Ω

To insure that we have the maximum voltage swing at the output, we will use
190

Note that we are carrying out our calculations to four places so that we can get accuracy to three
places. The bias resistors are determined by

Since we designed the bias circuit to place the quiescent point in the middle of the ac load line,
we can use

Vout(undistorted p-p) 1.8 (2.94 x 10-3 ) (2 K Ω || 2 K Ω ) =5.29 V

Now we can determine the gain of the amplifier itself.

Using voltage division, we can determine the gain of the overall circuit.

The value of Rin can be obtained as

Thus the overall gain of the amplifier is

This shows that the common-emitter amplifier provides high voltage gain. However, it is very
noisy, it has a low input impedance, and it does not have the stability of the emitter resistor
common emitter a

Design ofAmplifier
Example-2 (Emitter-Resistor Amplifier Design)

Design an emitter-resistor amplifier as shown in fig. 2to drive a 2 KΩ load using a pnp silicon
transistor, VCC = -24V, β = 200, Av = -10, and VBE = -0.7 V. Determine all element valuesand
calculate Ai, Rin, ICQ and the maximum undistorted symmetrical output voltage swing forthree
191

values of RC as given below:

1. RC =Rload
2. RC = 0.1Rload
3. RC = 10Rload

Fig. 2

Solution:

(a) RC =Rload

We use the various equations derived in previous lecture in order to derive the parameters of the
circuit.

From the voltage gain, we can solve for R'E.

So R'E = re + RE = 100 Ω

We can find the quiescent value of the collector current I C form the collector-emitter loop using
the equation for the condition of maximum output swing.

Therefore,
192

This is small enough that we shall ignore it to find that RE = 100 Ω. Since we now know β and RE.
We can use the design guideline.

RB = 0.1 β RE = 2 k Ω

As designed earlier, the biasing circuitry can be designed in the same manner and given by

VBB = -1.52 V

R1 = 2.14 K Ω

R2 = 3.6 K Ω

The maximum undistorted symmetrical peak to peak output swing is then

Vout (P-P) = 1.8 ICQ (Rload || RC ) = 13.5 V

Thus current gain Ai = -9.1

and input impedance Rin = 1.82 K Ω

(b) RC = 0.1Rload

we repeat the steps of parts (a) to find

RC =200 Ω Ri = 390 Ω

ICQ =-57.4 mA R2 =4.7K Ω

r'e = 0.45 Ω vout(p-p) = 18.7 V

RB = 360 Ω Ai = -1.64

VBB = -1.84 V Rin = 327 Ω

(C) RC =10Rload

Once again, we follow the steps of part (a) to find

RC =20 K Ω R1 =3.28K Ω

ICQ =-1.07 mA R2 = 85.6K Ω

r'e = 24.2 Ω vout(p-p) = 3.9 V


193

RB = 3.64K Ω Ai =-14.5
VBB = -0.886 V Rin = 2.91K W

We now compare the results obtained Table-I for the purpose of making the best choice for RC.

ICQ Ai Rin vout(p-p)

RC = Rload -7.5 mA -9.1 1.82K W 13.5 V

RC = 0.1 Rload -57.4 mA -1.64 327 W 20.8 V

RC = 10 Rload -1.07mA -14.5 2.91W 3.9 V

Table - 1 Comparsion for the three selections of R C

It indicates that of the three given ratios of RC to Rload, RC = Rload has the most desirable
performance in the CE amplifier stage.

It can be used as a guide to develop a reasonable designs. In most cases, this choice will provide
performance that meets specifications. In some applications, it may be necessary to do additional
analysis to find the optimum ratio of RC to Rload.

mplifier.

Design ofAmplifier
Example-2 (Emitter-Resistor Amplifier Design)

Design an emitter-resistor amplifier as shown in fig. 2to drive a 2 KΩ load using a pnp silicon
transistor, VCC = -24V, β = 200, Av = -10, and VBE = -0.7 V. Determine all element values and
calculate Ai, Rin, ICQ and the maximum undistorted symmetrical output voltage swing for three
values of RC as given below:

1. RC =Rload
2. RC = 0.1Rload
3. RC = 10Rload
194

Fig. 2

Solution:

(a) RC =Rload

We use the various equations derived in previous lecture in order to derive the parameters of the
circuit.

From the voltage gain, we can solve for R'E.

So R'E = re + RE = 100 Ω

We can find the quiescent value of the collector current I C form the collector-emitter loop using
the equation for the condition of maximum output swing.

Therefore,

This is small enough that we shall ignore it to find that RE = 100 Ω. Since we now know β and RE.
We can use the design guideline.

RB = 0.1 β RE = 2 k Ω
195

As designed earlier, the biasing circuitry can be designed in the same manner and given by

VBB = -1.52 V

R1 = 2.14 K Ω

R2 = 3.6 K Ω

The maximum undistorted symmetrical peak to peak output swing is then

Vout (P-P) = 1.8 ICQ (Rload || RC ) = 13.5 V

Thus current gain Ai = -9.1

and input impedance Rin = 1.82 K Ω

(b) RC = 0.1Rload

we repeat the steps of parts (a) to find

RC =200 Ω Ri = 390 Ω

ICQ =-57.4 mA R2 =4.7K Ω

r'e = 0.45 Ω vout(p-p) = 18.7 V

RB = 360 Ω Ai = -1.64

VBB = -1.84 V Rin = 327 Ω

(C) RC =10Rload

Once again, we follow the steps of part (a) to find

RC =20 K Ω R1 =3.28K Ω

ICQ =-1.07 mA R2 = 85.6K Ω

r'e = 24.2 Ω vout(p-p) = 3.9 V

RB = 3.64K Ω Ai =-14.5
VBB = -0.886 V Rin = 2.91K W

We now compare the results obtained Table-I for the purpose of making the best choice for RC.
196

ICQ Ai Rin vout(p-p)

RC = Rload -7.5 mA -9.1 1.82K W 13.5 V

RC = 0.1 Rload -57.4 mA -1.64 327 W 20.8 V

RC = 10 Rload -1.07mA -14.5 2.91W 3.9 V

Table - 1 Comparsion for the three selections of R C

It indicates that of the three given ratios of RC to Rload, RC = Rload has the most desirable
performance in the CE amplifier stage.

It can be used as a guide to develop a reasonable designs. In most cases, this choice will provide
performance that meets specifications. In some applications, it may be necessary to do additional
analysis to find the optimum ratio of RC to Rload.

Design ofAmplifier
Example- 3 (Capacitor-Coupled Emitter-Resistor Amplifier Design)

Design an emitter-resistor amplifier as shown in fig. 3with AV =-10, β =200 and R load = 1K Ω.
A pnp transistor is used and maximum symmetrical output swing is required.

Fig. 3

Solution:

As designed earlier, we shall chose RC = Rload = 10 kΩ.


197

The voltage gain is given by

where R'E= RE + r'e.

Substituting AV, Rload and RC in this equation, we find R'E= 50 Ω.

We need to know the value of r'e to fine RE. We first find Rac and Rdc, and then calculate the Q
point as follows (we assume r'e is small, so RE = R'E)

Rac = RE + RC || Rload = 550 Ω

Rdc = RE + RC = 1050 Ω

Now, the first step is to calculate the quiescent collector current needed to place the Q-point into
the center of the ac load line (i.e., maximum swing). The equation is

The quantity, r'e , is found as follows

Then

RE = 50 - re = 46.67 Ω

If there were a current gain or input resistance specification for this design, we would use it to
solve for the value of RB. Since is no such specification, we use the expression

RB =0.1 β RE = 0.1 (200) (46.6) = 932 Ω

Then continuing with the design steps,

and
198

The last equality assumes that rO is large compared to RC.

The maximum undistorted peak to peak output swing is given by

1.8 | ICQ | ( RC || Rload )=1.8 ( 0.0075 ) ( 500 ) = 6.75 V

The power delivered into the load and the maximum power dissipated by the transistor are found
as

The load lines for this circuit are shown in fig. 4.

Common Collector Amplifier:

If a high impedance source is connected to low impedance amplifier then most of the signal is
dropped across the internal impedance of the source. To avoid this problem common collector
199

amplifier is used in between source and CE amplifier. It increases the input impedence of the CE
amplifier without significant change in input voltage.

Fig. 1, shows a common collector (CC) amplifier. Since there is no resistance in collector circuit,
therefore collector is ac grounded. It is also called grounded collector amplifier. When input
source drives the base, output appears across emitter resistor. A CC amplifier is like a heavily
swamped CE amplifier with a collector resistor shorted and output taken across emitter resistor.

vout = vin - vBE

Fig. 1

Therefore, this circuit is also called emitter follower, because V BE is very small. As vin increases,
vout increases.

If vin is 2V, vout = 1.3V

If vin is 3V, vout = 2.3V.

Since vout follows exactly the vin therefore, there is no phase inversion between input and output.

The output circuit voltage equation is given by

VCE = VCC – IE RE

Since IE = C

IC = (VCC – VCE ) / RE

This is the equation of dc load line. The dc load line is shown in Fig.1.
200

Common CollectorAmplifier:
Voltage gain:

Fig. 2, shows an emitter follower driven by a small ac voltage. The input is applied at the base of
transistor and output is taken across the emitter resistor. Fig. 3, shows the ac equivalent circuit of
the amplifier. The emitter is replaced by ac resistance r'e.

Fig. 2 Fig. 3
The ac output voltage is given by

vout = RE ie

and, vin = ie (RE + r'e )

Therefore, A = RE / ( RE +r'e )

Since r'e<< RE

v= (approx)

Therefore, it is a unity gain amplifier. The practical


emitter follower circuit is shown in Fig. 4. Fig. 4

The ac source (vS) with a series resistance RS drives the transistor base. Because of the biasing
resistor and input impedance of the base, some of the ac signal is lost across the source resistor.
201

The ac equivalent circuit is shown in Fig. 5.

Fig. 5

The input impedance at the base is given by

The total input impedance of an emitter follower includes biasing resistors in parallel with input
impedance of the base.

zin = R1 || R2|| (r'e + RE)

Since RE is very large as compared to R1 and R2.

Thus, zin ≈ R1 ||R2

Therefore input impedance is very high.

Applying Thevenin's theorem to the base circuit of Fig. 5, it becomes a source vin and a series
resistance (R1 || R2 || RS ) as shown in Fig. 6.
202

Fig. 6

Common CollectorAmplifier
Example 1:

Find the Q-point of the emitter follower circuit of fig. 7with R1 = 10 KΩ and R2 = 20 KΩ.
Assume the transistor has a β of 100 and input capacitor C is very-very large.
203

Fig. 7

Solution:

We first find the Thevenin's equivalent of the base bias circuitry.

RB = R1 || R2 = 6.67 K Ω

From the bias equation we have

Example - 2

Find the output voltage swing of the circuit of fig. 7.

Solution:

The Q-Point location has already been calculated in Example-1. We found that the quiescent
collector current is 4.95 mA.

The Output voltage swing = 2 . IC peak . (RE || RLoad) = 2(4.95 x 10-3) (300) = 2.97V

This is less than the maximum possible output swing. Continuing the analysis,
204

VCEQ = VCC – ICQ RE = 9.03 V

V'CC = VCEQ + ICQ (RE || RLoad ) = 10.5 V

The load lines for this problem are shown in Fig. 8.

CLASSIFICATION OF AMPLIFIERS:

A circuit that increases the amplitude of the given input signal is an amplifier.A small ac signal
fed to the amplifier is obtained as a larger ac signal of the same frequency at the
output.Amplifiers constitute an essential part of radio,television and other communication
circuits.Depending on the nature and level of amplification and the impedance matching
requirements different types of amplifiers can be considered and they are discussed in this
chapter.

Amplifiers can be classified as follows:

1.Based on the transistor configuration

(a) Common emitteramplifier

(b) Common baseamplifier

(c ) Common emitter amplifier


205

2. Based on the active devices

(a) BJTamplifier

(b) FETamplifier

3. Based on the Q-point(operatingcondition)

(a) Class Aamplifier

(b) Class Bamplifier

(c) Class Camplifier

(d) Class AB amplifier

4.Based on the number ofstages

(a) Single stageamplifiers

(b) Multistageamplifiers

5.Based on theoutput

(a)Voltage amplifiers

(b)Power amplifiers

6. Based on the frequency response

(a)Audio frequency(AF) amplifier

(b)Intermediate Frequencyamplifier(IF)

(c )Radio Frequencyamplifier(RF)

7. Based on thebandwidth

(a) Narrow band amplifier(normally RF amplifier)


206

(b) Wide band amplifier(normally videoamplifier)

Distortion in amplifiers:

Amplifier Distortion

From the previous tutorials we learnt that for a signal amplifier to work correctly it requires some
form of DC Bias on its Base or Gate terminal so that it amplifies the input signal over its entire
cycle with the bias "Q-point" set as near to the middle of the load line as possible. This then gave
us a "Class-A" type amplification with the most common configuration being Common Emitter
for Bipolar transistors and Common Source for unipolar transistors. We also saw that the Power,
Voltage or Current Gain, (amplification) provided by the amplifier is the ratio of the peak input
value to its peak output value. However, if we incorrectly design our amplifier circuit and set the
biasing Q-point at the wrong position on the load line or apply too large an input signal, the
resultant output signal may not be an exact reproduction of the original input signal waveform. In
other words the amplifier will suffer from distortion. Consider the common emitter amplifier
circuit below.

Common Emitter Amplifier

Distortion of the signal waveform may take place because:

1. Amplification may not be taking place over the whole signal cycle due to incorrectbiasing.

2. The input signal may be too large, causing the amplifier tolimit.
207

3. The amplification may not be linear over the entire frequency range ofinputs.

This means then that during the amplification process of the signal waveform, some form of
Amplifier Distortion has occurred.

Amplifiers are basically designed to amplify small voltage input signals into much larger output
signals and this means that the output signal is constantly changing by some factor or value times
the input signal for all input frequencies. We saw previously that this multiplication factor is
called the Beta, β value of the transistor. Common emitter or even common source type transistor
circuits work fine for small AC input signals but suffer from one major disadvantage, the bias Q-
point of a bipolar amplifier depends on the same Beta value which may vary from transistors of
the same type, ie. the Q-point for one transistor is not necessarily the same as the Q-point for
another transistor of the same type due to the inherent manufacturing tolerances. If this occurs
the amplifier may not be linear and Amplitude Distortion will result but careful choice of the
transistor and biasing components can minimise the effect of amplifierdistortion.

Amplitude Distortion

Amplitude distortion occurs when the peak values of the frequency waveform are attenuated
causing distortion due to a shift in the Q-point and amplification may not take place over the
whole signal cycle. This non-linearity of the output waveform is shown below.

Amplitude Distortion due to Incorrect Biasing

If the bias is correct the output waveform should look like that of the input waveform only
bigger, (amplified). If there is insufficient bias the output waveform will look like the one on the
right with the negative part of the output waveform "cut-off". If there is too much bias the output
208

waveform will look like the one on the left with the positive part "cut-off". When the bias
voltage is too small, during the negative part of the cycle the transistor does not conduct fully so
the output is set by the supply voltage. When the bias is too great the positive part of the cycle
saturates the transistor and the output drops almost to zero.

Even with the correct biasing voltage level set, it is still possible for the output waveform to
become distorted due to a large input signal being amplified by the circuits gain. The output
voltage signal becomes clipped in both the positive and negative parts of the waveform an no
longer resembles a sine wave, even when the bias is correct. This type of amplitude distortion is
called Clipping and is the result of "Over-driving" the input of the amplifier.

When the input amplitude becomes too large, the clipping becomes substantial and forces the
output waveform signal to exceed the power supply voltage rails with the peak (+ve half) and the
trough (-ve half) parts of the waveform signal becoming flattened or "Clipped-off". To avoid this
the maximum value of the input signal must be limited to a level that will prevent this clipping
effect as shown above.

Amplitude Distortion due to Clipping

Amplitude Distortion greatly reduces the efficiency of an amplifier circuit. These "flat tops" of
the distorted output waveform either due to incorrect biasing or over driving the input do not
contribute anything to the strength of the output signal at the desired frequency. Having said all
that, some well known guitarist and rock bands actually prefer that their distinctive sound is
highly distorted or "overdriven" by heavily clipping the output waveform to both the +ve and -ve
power supply rails. Also, excessive amounts of clipping can also produce an output which
resembles a "square wave" shape which can then be used in electronic or digital circuits.
209

We have seen that with a DC signal the level of gain of the amplifier can vary with signal
amplitude, but as well as Amplitude Distortion, other types of distortion can occur with AC
signals in amplifier circuits, such as Frequency Distortion and Phase Distortion.

Frequency Distortion

Frequency Distortion occurs in a transistor amplifier when the level of amplification varies with
frequency. Many of the input signals that a practical amplifier will amplify consist of the
required signal waveform called the "Fundamental Frequency" plus a number of different
frequencies called "Harmonics" superimposed onto it. Normally, the amplitude of these
harmonics are a fraction of the fundamental amplitude and therefore have very little or no effect
on the output waveform. However, the output waveform can become distorted if these harmonic
frequencies increase in amplitude with regards to the fundamental frequency. For example,
consider the waveform below:

Frequency Distortion due to Harmonics

In the example above, the input waveform consists a the fundamental frequency plus a second
harmonic signal. The resultant output waveform is shown on the right hand side. The frequency
distortion occurs when the fundamental frequency combines with the second harmonic to distort
the output signal. Harmonics are therefore multiples of the fundamental frequency and in our
simple example a second harmonic was used. Therefore, the frequency of the harmonic is 2
times the fundamental, 2 x f or 2f. Then a third harmonic would be 3f, a fourth, 4f, and so on.
Frequency distortion due to harmonics is always a possibility in amplifier circuits containing
reactive elements such as capacitance or inductance.

Phase Distortion

Phase Distortion or Delay Distortion occurs in a non-linear transistor amplifier when there is a
time delay between the input signal and its appearance at the output. If we call the phase change
between the input and the output zero at the fundamental frequency, the resultant phase angle
delay will be the difference between the harmonic and the fundamental. This time delay will
depend on the construction of the amplifier and will increase progressively with frequency
within the bandwidth of the amplifier. For example, consider the waveform below:
210

Phase Distortion due to Delay

Any practical amplifier will have a combination of both "Frequency" and "Phase" distortion
together with amplitude distortion but in most applications such as in audio amplifiers or power
amplifiers, unless the distortion is excessive or severe it will not generally affect the operation of
the system.

FET AMPLIFIERS
5.4.0 INTRODUCTION
Field Effect Transistor (FET) amplifiers provide an excellent voltage gain and high input
impedence. Because of high input impedence and other characteristics of JFETs they are
preferred over BJTs for certain types of applications.

There are 3 basic FET circuit configurations:


i)Common Source
ii)Common Drain
iii)Common Gain
Similar to BJT CE,CC and CB circuits, only difference is in BJT large output collector
current is controlled by small input base current whereas FET controls output current by means
of small input voltage. In both the cases output current is controlled variable.
FET amplifier circuits use voltage controlled nature of the JFET. In Pinch off region, I D
depends only on VGS.

Common Source (CS)Amplifier


211

Fig. 7.1 (a) CS Amplifier (b) Small-signal equivalent circuit

A simple Common Source amplifier is shown in Fig. 7.1(a) and associated small signal
equivalent circuit using voltage-source model of FET is shown in Fig. 7.1(b)

Voltage Gain
Source resistance (RS) is used to set the Q-Point but is bypassed by CS for mid-frequency
operation. From the small signal equivalent circuit ,the output voltage
VO = -RDµVgs(RD + rd)
Where Vgs = Vi , the input voltage,
Hence, the voltage gain,
AV = VO / Vi = -RDµ(RD + rd)

Input Impedence
From Fig. 7.1(b) Input Impedence is
Zi = RG
For voltage divider bias as in CE Amplifiers of BJT
RG = R1 ║ R2

Output Impedance
212

Output impedance is the impedance measured at the output terminals with the input voltage V I =
0
From the Fig. 7.1(b) when the input voltage Vi = 0, Vgs = 0 and hence
µ Vgs = 0
The equivalent circuit for calculating output impedence is given in Fig. 7.2.
Output impedence Zo = rd ║ RD
Normally rd will be far greater than RD . Hence Zo ≈ RD

Common DrainAmplifier
A simple common drain amplifier is shown in Fig. 7.2(a) and associated small signal equivalent
circuit using the voltage source model of FET is shown in Fig. 7.2(b).Since voltage Vgd is more
easily determined than Vgs, the voltage source in the output circuit is expressed in terms of V gs
and Thevenin’s theorem.

Fig. 7.2 (a)CD Amplifier (b)Small-signal equivalent circuit


Voltage Gain
The output voltage,
VO = RSµVgd / (µ + 1) RS+ rd
Where Vgd = Vi the inputvoltage.
Hence, the voltage gain,
Av = VO / Vi = RSµ / (µ + 1) RS + rd
213

Input Impedence
From Fig. 7.2(b), Input Impedence Zi = RG

Output Impedence
From Fig. 7.2(b), Output impedence measured at the output terminals with input voltage Vi = 0
can be calculated from the following equivalent circuit.
As Vi = 0: Vgd = 0: µvgd / (µ + 1) = 0
Output Impedence
ZO = rd / (µ + 1) ║RS
When µ » 1
ZO = ( rd / µ) ║RS = (1/gm) ║RS

BIASINGFET:-
For the proper functioning of a linear FET amplifier, it is necessary to maintain the
operating point Q stable in the central portion of the pinch off region The Q point should be
independent of device parameter variations and ambient temperature variations

This can be achieved by suitably selecting the gate to source voltage VGS and drain current I D which is
referred to as biasing

JFET biasing circuits are very similar to BJT biasing circuitsThe main difference between JFET
circuits and BJT circuits is the operation of the active components themselves

There are mainly two types of Biasing circuits

1. Selfbias
2. Voltage dividerbias.

5.5.1. SELF BIAS:-


Self bias is a JFET biasing circuit that uses a source resistor to help reverse bias the JFET gate.

A self bias circuit is shown in the fig 7.3


214

Self bias is the most common type of JFET bias. This JFET must be operated such that gate
source junction is always reverse biased. This condition requires a negative V GS for an N channel JFET
and a positive VGS for P channel JFET. This can be achieved using the self bias arrangement as shown in
Fig 7.3. The gate resistor RG doesn’t affect the bias because it has essentially no voltage drop across it,
and : the gate remains at 0V .RG is necessary only to isolate an ac signal from ground in amplifier
applications. The voltage drop across resistor RS makes gate source junction reversebiased.

DC analysis of self Bias:-

In the following DC analysis , the N channel J FET shown in the fig7.4. is used for illustration.

ForDCanalysiswecanreplacecouplingcapacitorsbyopencircuitsand we canalsoreplace the


resistor RG by a short circuitequivalent.

:. IG = 0

The relation between ID and VGS is given by

Id=Idss[1- ]2
215

VGS for N channel JFET is =-id Rs

Substuting this value in the above equation

Id=Idss[1- ]2

Id=Idss[1+ ]2

For the N-chanel FET in the above figure

Is produces a voltage drop across Rs and makes the source positive w.r.t ground

in any JFET circuit all the source current passes through the device to drain circuit this is due to the fact that

there is no significant gate current

therefore we can define source current as Is=Id and Vg=0 then

Vs= Is Rs =IdRs

Vgs=Vg-Vs=0-IdRs=-IdRs

Drawing the self bias line:-

Typical transfer characteristics for a self biased JFET are shown in the fig7.5.

The maximum drain current is 6mA and the gate source cut off voltage is -3V. This means the gate
voltage has to be between 0 and -3V.
216

Now using the equation VGS = -IDRS and assuming RS of any suitable value we can draw the self bias line.

Let us assume RS = 500Ω

With this Rs , we can plot two points corresponding to I D = 0 and Id = IDSS

for ID = 0

VGS = -ID RS

VGS = 0X (500.Ω) = 0V

So the first point is (0 ,0)

( Id, VGS)

For ID= IDSS=6mA

VGS = (-6mA) (500 Ω) = -3V

So the 2nd Point will be (6mA,-3V)

By plotting these two points, we can draw the straight line through the points. This line will
intersect the transconductance curve and it is known as self bias line. The intersection point gives the
operating point of the self bias JFET for the circuit.

At Q point , the ID is slightly > than 2mA and VGS is slightly > -1V. The Q point for the self bias
JFET depends on the value of Rs.If Rs is large, Q point far down on the transconductance curve ,ID is
small, when Rs is small Q point is far up on the curve , I D is large.
217

5.5.2 VOLTAGE DIVIDER BIAS:-

The fig7.6 shows N channel JFET with voltage divider bias. The voltage at the source of JFET
must be more positive than the voltage at the gate in order to keep the gate to source junction reverse
biased. The source voltageis

VS = IDRS

The gate voltage is set by resistors R1 and R2 as expressed by the following equation using the
voltage divider formula.

Vg= Vdd

For dc analysis fig 7.7


218

Applying KVL to the input circuit

VG-VGS-VS =0

:: VGS = VG-Vs=VG-ISRS

VGS=VG-IDRS :: IS =ID

Applying KVL to the input circuit we get

VDS+IDRD+VS-VDD =0

::VDS = VDD-IDRD-IDRS

VDS = VDD-ID ( RD +RS )

The Q point of a JFET amplifier , using the voltage divider biasis

IDQ = IDSS[1-VGS/VP]2

VDSQ = VDD-ID ( RD+RS)

5.6 JFET AS A VVR OR VDR:-


Let us consider the drain characteristics of FET as shown in the fig.

In this characteristics we can see that in the region before pinch off voltage, drain characteristics
are linear, i.e. FET operation is linear. In this region the FET is useful as a voltage controlled resistor,i.e.
the drain to source resistance is controlled by the bias voltage VGS.( In this region only FET behaves like
an ordinary resistor This resistances can be varied by V GS ) .The operation of FET in the region is useful in
219

most linear applications of FET.In such an application the FET is also referred to as a voltage variable
resistor (VVR) or voltage dependent resistor (VDR).

The drain to source conductance ( rd )

gd= for small values of VDS which may also be expressed as

gd=gd0(1- )1/2)

Where gd0 is the value of drain conductance

When the variation of the rd with VGS can be closely approximated by the expression

rd= ) Where ro = drain resistance at zero gate bias.K = a constant, dependent uponFET
type.

5.6.1 APPLICATION OF VVR

The VVR property of FET can be used to vary the voltage gain of a multistage amplifier A, as the
signal level is increased. This action is called AGC automatic gain control. A typical arrangement is shown
in the fig.

Here maximum value of signal is taken rectified; filter to produce a DC voltage proportional to
the output signal level. This voltage is applied to the gate of JFET, this causing the resistance between
drain and source to change. As this resistance is connected across RE, so effective RE also changes
220

according to change in the drain to source resistance. When output signal level increases, the drain to
source resistance rd increases, increasing effective RE. Increase in RE causes the gain of transistor Q1 to
decrease, reducing the output signal. Exactly reverse process takes place when output signal level
decreased.

:: The output signal level is maintained constant. It is to be noted that the DC bias conditions of
Q1 are not affected by JFET since FET is isolated from Q1 by capacitor C2

Potrebbero piacerti anche