Sei sulla pagina 1di 5

Current Date: 3/3/2019 10:22:01 PM

Units System: kN_m

Design code: AISC 360-16 ASD

DEMANDS
Description Pu Mu22 Mu33 Vu2
Vu3 Load type
kN kN*m kN*m kN kN

LC-3 -45.45 0.00 0.00 -1.12


0.01 Design
LC-4 -8.13 0.00 0.00 -0.23
0.00 Design
LC-5 39.15 0.00 0.00 16.90 -
0.06 Design
LC-6 37.06 0.00 0.00 -22.32 -
15.86 Design
LC-7 10.56 0.00 0.00 -20.50
0.03 Design
LC-8 34.37 0.00 0.00 -22.17
15.84 Design
LC-9 -51.58 0.00 0.00 6.24
0.00 Design
LC-10 -64.10 0.00 0.00 -1.62
0.27 Design
LC-11 -77.01 0.00 0.00 -9.47
0.04 Design
LC-12 -64.49 0.00 0.00 -1.61 -
0.23 Design
LC-13 -12.02 0.00 0.00 16.79 -
0.04 Design
LC-14 -13.28 0.00 0.00 -6.75 -
9.52 Design
LC-15 -29.17 0.00 0.00 -5.66
0.01 Design
LC-16 -14.89 0.00 0.00 -6.66
9.50 Design
LC-17 -24.54 0.00 0.00 8.92
0.22 Design
LC-18 -25.79 0.00 0.00 -14.61 -
9.25 Design
LC-19 -41.69 0.00 0.00 -13.52
0.28 Design
LC-20 -27.40 0.00 0.00 -14.52
9.76 Design
LC-21 -84.43 0.00 0.00 -19.21
0.07 Design
LC-22 -83.17 0.00 0.00 4.32
9.55 Design
LC-23 -67.27 0.00 0.00 3.23
0.02 Design
LC-24 -81.56 0.00 0.00 4.23 -
9.47 Design
LC-25 -71.91 0.00 0.00 -11.35 -
0.20 Design
LC-26 -70.65 0.00 0.00 12.19
9.28 Design
LC-27 -54.76 0.00 0.00 11.09 -
0.25 Design
LC-28 -69.04 0.00 0.00 12.09 -
9.74 Design
LC-29 -75.01 0.00 0.00 -1.89
0.02 Design
LC-30 -64.30 0.00 0.00 -1.62
0.02 Design
LC-31 -36.70 0.00 0.00 18.05 -
0.04 Design
LC-32 -37.96 0.00 0.00 -5.49 -
9.52 Design
LC-33 -53.86 0.00 0.00 -4.39
0.01 Design
LC-34 -39.57 0.00 0.00 -5.39
9.50 Design
LC-35 -52.35 0.00 0.00 8.22
0.29 Design
LC-36 -53.61 0.00 0.00 -15.31 -
9.18 Design
LC-37 -69.50 0.00 0.00 -14.22
0.35 Design
LC-38 -55.22 0.00 0.00 -15.22
9.83 Design
LC-39 -115.47 0.00 0.00 -21.88
0.08 Design
LC-40 -114.21 0.00 0.00 1.66
9.56 Design
LC-41 -98.31 0.00 0.00 0.57
0.03 Design
LC-42 -112.60 0.00 0.00 1.57 -
9.46 Design
LC-43 -99.82 0.00 0.00 -12.05 -
0.25 Design
LC-44 -98.57 0.00 0.00 11.49
9.23 Design
LC-45 -82.67 0.00 0.00 10.39 -
0.30 Design
LC-46 -96.96 0.00 0.00 11.39 -
9.79 Design
LC-47 -20.54 0.00 0.00 8.90 -
0.01 Design
LC-48 -36.19 0.00 0.00 -0.92
0.32 Design
LC-49 -52.33 0.00 0.00 -10.74
0.04 Design
LC-50 -36.68 0.00 0.00 -0.91 -
0.30 Design

Design for major axisBase plate (AISC 360-16 ASD)


GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. Max. Sta.
References

Base plate
Distance from anchor to edge [mm] 115.24 6.35 -

Weld size [1/16in] 5 3.00 - table


J2.4

DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio
References

Concrete base
Axial bearing [kN/m2] 11993.24 524.84 LC-39-38 0.04 DG1
3.1.1;

A2 = ((B/N)*Ncs)*Ncs = ((400 [mm] /550 [mm] )*650 [mm] )*650 [mm] = 3.07E+05 [mm2] DG1 Sec
3.1.1
A1 = B*N = 400 [mm] *550 [mm] = 2.20E+05 [mm2] DG1 Sec
3.1.1
fp, max = (1/W)*min(0.85*f'c*(A2/A1)1/2, 1.7*f'c) = 0.433*min(0.85*27.58 [N/mm2] *(1.4)1/2, 1.7*27.58 [N/mm2] ) = 11.99
[N/mm2] DG1
3.1.1
Base plate
Flexural yielding (bearing interface) [kN*m/m] 5.99 1.86 LC-39-38 0.31
DG1 Sec 3.1.2

(1/W)Mn = (1/W)*Fy*tp2/4 = 0.599*248.21 [N/mm2] *12.7 [mm] 2/4 = 5.99 [kN*m/m] DG1 Eq.
3.3.13
A2 = ((B/N)*Ncs)*Ncs = ((400 [mm] /550 [mm] )*650 [mm] )*650 [mm] = 3.07E+05 [mm2] DG1 Sec
3.1.1
A1 = B*N = 400 [mm] *550 [mm] = 2.20E+05 [mm2] DG1 Sec
3.1.1
m = (N - 0.95*dc)/2 = (550 [mm] - 0.95*508 [mm] )/2 = 33.7 [mm] DG1 Sec
3.1.2
n = (B - 0.8*bc)/2 = (400 [mm] - 0.8*289.56 [mm] )/2 = 84.18 [mm] DG1 Sec
3.1.2
Pp = min(0.85*f'c*A1*(A2/A1)1/2, 1.7*f'c*A1) = min(0.85*27.58 [N/mm2] *2.20E+05 [mm2] *(1.4)1/2, 1.7*27.58 [N/mm2]
*2.20E+05 [mm2] ) = 6094.97 [kN] Eq. J8-2

X = (4*dc*bc/(dc + bc) )*P/((1/W)*Pp) = (4*508 [mm] *289.56 [mm] /(508 [mm] + 289.56 [mm] )2)*115.47 [kN] /
2

(0.433*6094.97 [kN] ) = 0.0405 DG1 Sec


3.1.2
l = min(2*(X)1/2/(1 + (1 - X)1/2), 1.0) = min(2*(0.0405)1/2/(1 + (1 - 0.0405)1/2), 1.0) = 0.203 DG1 Sec
3.1.2

n' = l*(dc*bc)1/2/4 = 0.203*(508 [mm] *289.56 [mm] )1/2/4 = 19.49 [mm] DG1 Sec
3.1.2
l = max(m, n, n') = max(33.7 [mm] , 84.18 [mm] , 19.49 [mm] ) = 84.18 [mm] DG1 Sec
3.1.2
fp = P/(B*N) = 115.47 [kN] /(400 [mm] *550 [mm] ) = 0.525 [N/mm2] DG1 Sec
3.1.2
Mpl = fp*(l2/2) = 0.525 [N/mm2] *(84.18 [mm] 2/2) = 1.86 [kN*m/m] DG1 Sec
3.1.2

Flexural yielding (tension interface) [kN*m/m] 5.99 3.76 LC-5-4 0.63


DG1 Eq. 3.3.13

(1/W)Mn = (1/W)*Fy*tp2/4 = 0.599*248.21 [N/mm2] *12.7 [mm] 2/4 = 5.99 [kN*m/m] DG1 Eq.
3.3.13
MpT = Mstrip/Beff = 1.34 [kN*m] /357.39 [mm] = 3.76 [kN*m/m]

Column
Weld capacity [kN/m] 1218.98 47.49 LC-5-4 0.04 p. 8-9,
Sec. J2.5, Sec. J2.4, DG1 p. 35

LoadAngleFactor = 1 + 0.5*(sin(q))1.5 = 1 + 0.5*(sin(1.57))1.5 = 1.5 p. 8-9


Fw = 0.6*FEXX*LoadAngleFactor = 0.6*482.63 [N/mm2] *1.5 = 434.37 [N/mm2] Sec. J2.5
Aw = (2)1/2/2*D/16 [in] *L = (2)1/2/2*5/16 [in] *1000 [mm] = 5612.66 [mm2] Sec. J2.4
(1/W)Rw = (1/W)*Fw*Aw/L = 0.5*434.37 [N/mm2] *5612.66 [mm2] /1000 [mm] = 1.22 [kN/mm]
beff = 2*L = 2*68.7 [mm] = 137.39 [mm] DG1 p.
35
Maximum weld load = T/beff = 6.52 [kN] /137.39 [mm] = 0.0475 [kN/mm]

Elastic method weld shear capacity [kN/m] 812.66 27.43 LC-6-5 0.03 p. 8-9,
Sec. J2.5, Sec. J2.4

LoadAngleFactor = 1 + 0.5*(sin(q))1.5 = 1 + 0.5*(sin(0))1.5 = 1 p. 8-9


Fw = 0.6*FEXX*LoadAngleFactor = 0.6*482.63 [N/mm2] *1 = 289.58 [N/mm2] Sec. J2.5
Aw = (2)1/2/2*D/16 [in] *L = (2)1/2/2*5/16 [in] *1000 [mm] = 5612.66 [mm2] Sec. J2.4
(1/W)Rw = (1/W)*Fw*Aw/L = 0.5*289.58 [N/mm2] *5612.66 [mm2] /1000 [mm] = 0.813 [kN/mm]
fv = V/Lshear = 22.32 [kN] /813.82 [mm] = 0.0274 [kN/mm]

Elastic method weld axial capacity [kN/m] 1218.98 37.96 LC-5-4 0.03 p. 8-9,
Sec. J2.5, Sec. J2.4
LoadAngleFactor = 1 + 0.5*(sin(q))1.5 = 1 + 0.5*(sin(1.57))1.5 = 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor = 0.6*482.63 [N/mm2] *1.5 = 434.37 [N/mm2] Sec. J2.5
Aw = (2)1/2/2*D/16 [in] *L = (2)1/2/2*5/16 [in] *1000 [mm] = 5612.66 [mm2] Sec. J2.4
(1/W)Rw = (1/W)*Fw*Aw/L = 0.5*434.37 [N/mm2] *5612.66 [mm2] /1000 [mm] = 1.22 [kN/mm]
fa = P/L = 39.15 [kN] /1031.24 [mm] = 0.038 [kN/mm]
fb = M*c/I = 0 [kN*m] *254 [mm] /6.92E+07 [mm3] = 0 [kN/mm]
f = fb + fa = 0 [kN/mm] + 0.038 [kN/mm] = 0.038 [kN/mm]

Ratio 0.63

Global critical strength ratio 0.63

Major axisMaximum compression (LC-39)


N/mm2

Maximum bearing pressure 0.52


Minimum bearing pressure 0.52
Maximum anchor tension 0.00
Minimum anchor tension 0.00
Neutral axis angle 0.00
Bearing length 1000000000000000000000000000000000.00

Anchors tensions
Anchor Transverse Longitudinal Shear Tension
mm mm kN kN

1 -80.00 -110.00 -3.65 0.00


2 -80.00 0.00 -3.65 0.00
3 -80.00 110.00 -3.65 0.00
4 80.00 110.00 -3.65 0.00
5 80.00 0.00 -3.65 0.00
6 80.00 -110.00 -3.65 0.00

Maximum tension (LC-5)


N/mm2

Maximum bearing pressure 0.00


Minimum bearing pressure 0.00
Maximum anchor tension 6.52
Minimum anchor tension 6.52
Neutral axis angle 0.00
Bearing length -1000000000000000000000000000000000.00

Anchors tensions
Anchor Transverse Longitudinal Shear Tension
mm mm kN kN

1 -80.00 -110.00 2.82 6.52


2 -80.00 0.00 2.82 6.52
3 -80.00 110.00 2.82 6.52
4 80.00 110.00 2.82 6.52
5 80.00 0.00 2.82 6.52
6 80.00 -110.00 2.82 6.52

NOTES
Anchors only designed for LRFD code

NOTATION
A1 : Base plate area
A2 : Maximum area of portion of the concrete supporting surface that is geometrically similar to and
concentric with the load area
Aw : Effective area of the weld
A2/A1 : Ratio between the concrete support area and the base plate area
B : Base plate design width
bc : Width of column section
beff : Effective width of the compression block
Beff : Controlling ffective width
c : Distance to weld group
dc : Column depth
D : Number of sixteenths of an inch in the weld size
fa : Axial stress on welds
fb : Bending stress on welds
f'c : Specified compressive strength of concrete
f : Combined stress on welds
FEXX : Electrode classification number
fp : Uniformly bearing stress under base plate
fp, max : Maximum uniformly bearing stress under base plate
fv : Vertical shear force on weld
Fw : Nominal strength of the weld metal per unit area
Fy : Specified minimum yield stress
I : Inertia of weld group
L : Distance from the anchor rod to the column
l : Critical base plate cantilever dimension
L : Length of weld
Lshear : Length of weld receiving shear
l : Auxiliary variable to calculate the critical base plate cantilever dimension
LoadAngleFactor : Load angle factor
M : Bending required
m : Base plate bearing interface cantilever direction parallel to moment direction
Mpl : Plate bending moment per unit width
MpT : Plate bending moment per unit width at tension unstiffened strip interface
Mstrip : Maximum bending moment at the strip
Maximum weld load : Maximum weld load
N : Base plate design length
n : Base plate bearing interface cantilever direction perpendicular to moment direction
n' : Yield line theory cantilever distance from column web or column flange
Ncs : Length of the concrete supporting surface or pier parallel to moment design direction
P : Required axial force
Pp : Nominal bearing stress
(1/W) : Design factors
(1/W)Mn : Design or allowable strength per unit length
(1/W)Rw : Fillet weld capacity per unit length
T : Anchor rod tensile strength required
tp : Plate thickness
q : Load angle
V : Shear load
wmin : Minimum weld size required
X : Auxiliary variable to calculate the critical base plate cantilever dimension

Potrebbero piacerti anche