Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
LET'S DO IT MINER-
Q1. Which cut is used for solid blasting in Indian coal Mines
c) Wedge cut
Q2. Permitted explosives are safe to use because
d) Special chemical are used to extinguish the spark produced during blasting.
Q3. Burden is the distance between
c) Distance between first row of blast holes and bench
Q4. Which of the following explosive have maximum strength
c) RDX
Q5. To measure the performance of blasting which factor is calculated
d) Powder factor
Q6. What is the formula for blast ability?
a) B = c / t
Q7 As per provision of regulation 170 (1a)(b) of CMR 1957 danger zone is an area falling a radius of -----
---
d) 300m
Q8 While blasting in hot strata the temperature of hole should not exceed
d) 80 c
c) muffled blasting
Q10 While dealing with Misfire shot the relieving hole is drilled at a distance not less than
a) 10 m
Q11 As per CMR the recapping of rope is done once at least in every
c) 6 months
Q12 what is the maximum angle of fleet is permissible in winding as per CMR
b) 1.5
Q13 a coal seam is said to be of degree III if rate of emission of gas in m3 /te of coal raised is
c) more than 10
Q 14 reportable injury means any injury other than serious bodily injury, which involves the enforced
absence of injured person from work for a period of
d) 72 hours or more
Q15 When the air and mineral flow is in same direction the ventilation is known as
a) Homotropal ventilation
Q17 A seam is worked at a depth of 70 mtrs . from surface and the width of the galleries is 3.2 mtr the
dimension of the pillar should not exceed
b)16.5 mtrs
Q18 in board and pillar panel worked in conjuction with hydraulic stowing extraction line preferred is
a) step diagonal
a) Sedimentary rocks
Q22 In India a coal seam is defined as a thick coal seam if its thickness is
a) CO2 + N2
Q24 When working approaches waterlogged areas apparatus used as precautionary measure is
d)Drum winding
c) Explosion
d) 5mg/m2 of air
a) 4.5 years
a) to prevent the passage of flame from inside to the outside of the lamp
e) Silica gel
b) 3
Q34 According to CMR 1957 CH4 % in return airway should not exceed
c) 0.75%
Q35 the wet bulb temperature in development faces should not exceed
a) 33 C
Q36 In contiguous seams means the parting between two seams is within
b) 9m
Q37 which of the following instruments is used to measure the cooling power of the air
d) Katathermometer
a) Splicing
Q42 fast and accurate extension of centerlines in long tunnels can be done by
Q43 Mechanized opencast mining in India is economically feasible at present if the overburden to coal
ratio is approximately up to
c) 1in 8
Q44 for overburden removal with shovel dumper combination the optimum size of the dumper depends
on
Q45 In an underground coal mine the place where explosive is stored in underground is called as
a) Reserve station
Q46 for heavy duty crushing on hard material the type of jaw crusher normally selected is
Q47 To separate two finely divided solids from one another the process to be selected is
a) Floating
a) Hydrothermal
Q50 If the RQD of the ore and wall rock are low the method of stoping selected will be
c) Block caving
Q52 In the panel caving system of block caving the contact between the ore and capping is kept
b)Inclined
c)2000:1
Q54 In any working below ground there should be provided at least two shafts or incline which should be
away from each other by a minimum distance
b)13.5 mtrs
Q56 RQD is a quantitative index based on core recovery procedure, which is determined by incorporation
of only those pieces of core that is
Q57 In a contoured Map if there are higher values in side the loop it indicates
a) Ridge
Q58 The intersection of a vertical line through the observer’s station with the upper portion of the
celestrial sphere is called
a) Nadir
a) Subtractive
a) 1in 5000
Q61 The earliest indication of the spontaneous heating of coal can be given by
a) Sweating of strata
Q62 In an underground coal mine ventilated by 100 HP fan (Air HP) it is required to double the quantity
ofair for the purpose of air HP required will be
c) 800 H.P.
a) Galena
b) Labour Ministry
a) Over wind
Q66 balance rope is used on Koepe friction winder
Q68 LHD is a
a) involute
a) A dry method
Q71 Notice to regional inspector of mines about occurrence of serious accident is given in form
a) IV A
Q72 Blasting Gallery method is not suitable for working seam thickness
a) Less than 7 m
Q73 The size and speed of rotation being the same the head developed is max in case of
d) A forward bladed centrifugal fan
Q74 In water gas explosion the two highly explosive gases that are involved are
a) H2 and CO
Q75 In an underground working area CH4 and CO2 are normally expected to be found respectively
Q76 The most important parameter of a dust that governs its physiological effect is
d) Size of dust
Q77 In a mine a big roof fall has taken place in the mine intake place in main intake airway. The fan drift
water gauge
b) Will register an increase
Q79 . 60 dB + 60dB
c) 63 dB
Q80 In ventilation network analysis, kirchhoff’s first law is used which states
d) 4 amp
Q86 A 10% increase in cross sectional area of a roadway will reduce the resistance approximately by
a) 10%
Q87 The recommended instrument for the air borne respirable dust sampling in the Indian mines is
d)NCB/MRE-113A
Q88 The oxygen concentration in underground mine should not be less than
c)19%
b)38 cms
Q90 A cap lamp must be able to produce an illumination of
a) 0.25 lumans
a) filtration
d)Colour of dust
c)Psychrometer
c)1 0 C / 38m
Q.2: The spacing of the trenches pits and boreholes depend on:
a) The length of the ore body.
b) The modes of occurrence of the deposits.
c) The depth of the deposits.
d) The outcrops of the deposits.
Answer:(b)
Q.3: The grade which is available from a property after actual mining is:
a) Computed grade.
b) Effective grade.
c) Run - of - mine grade.
d) Pit head grade.
Answer:(b)
Q.6: The drill holes which are driven vertically and make the sides of the excavation are
Described as:
a) Easers.
b) Simpers.
c) Dressers.
d) Hole directors.
Answer:(c)
Q.10: The openings in the mini, which serve as a means of entry is known as:
a) Shafts.
b) Edits
c) Cross cut.
d) Stop.
Answer:(a)
Q.15: The width of the ore body which can be economically mined is:
a) Stopping width.
b) Assay width.
c) Actual width.
d) Grady width.
Answer:(a)
Q.20: When the material collected to represent a rock type, or a formation or an ore body in
the quantitative sense then it is termed as:
a) Specimen.
b) Sample.
c) Both specimen and sample can be used.
d) Quantitative specimen.
Answer:(b)
Q.24: The ore reserves for which tonnage and grade are computed party from specific
Measurements and partly from projection for a reasonable distance on geologic evidence is
Known as:
a) Proved or measured ore reserves
b) Probable or indicated ore reserves.
c) Possible or inferred ore reserves.
d) Actual ore reserves.
Answer:(d)