Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Rev. 3.0
May 2009
1. Release Info / Disclaimer
CASH FEVER™ - Setup and Configuration
(for APL™ based installations)
Rev. 3.0
Copyright Notice:
© 2007 - 2009, ATRONIC. All rights reserved.
No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval
system, or translated into any human or computer language, in any form or by any means, electronic,
mechanical, magnetic, manual, or otherwise, or disclosed to third parties without the express written
permission obtained from a properly authorized official of ATRONIC.
DISCLAIMER
ATRONIC makes no representation or warranties, express or implied, with respect to this publication,
or any product of ATRONIC, including but not limited to warranties of merchantability or fitness for any
particular purpose. ATRONIC reserves the right to make changes, enhancements, revisions and altera-
tions of any kind to this publication or the product(s) it covers without obligation to notify any person,
institution or organization of such changes, enhancements, revisions and alterations.
TRADEMARKS
This document may contain trademarks of ATRONIC. All other brand and product names are trademarks
or registered trademarks of their respective companies.
Table of Contents
1. Release Info / Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Hardware Components / Package . . . . . . . . . . . . . . . . . . . 7
3.3 Important Configuration Notes . . . . . . . . . . . . . . . . . . . . . 8
3.3.1 Progressive Calculation . . . . . . . . . . . . . . . . . . . . . 8
3.3.2 Base Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3.3 Configuration Code . . . . . . . . . . . . . . . . . . . . . . . 8
3.3.4 Jackpot Handpays . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3.5 Older Commboard Software . . . . . . . . . . . . . . . . . . 8
4. Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1 Atronic Progressive Link™ (APL™) . . . . . . . . . . . . . . . . . . . 9
4.1.1 What is APL™? . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1.2 CASH FEVER™ Link Size . . . . . . . . . . . . . . . . . . . . . 9
4.1.3 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1.4 Commboard Wiring Diagram . . . . . . . . . . . . . . . . . 11
4.2 Commboard Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2.1 Required Settings . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.2 Optional Settings . . . . . . . . . . . . . . . . . . . . . . . . 14
6. Machine Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.2 RAM Reset Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.3 Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.3.1 Initial Setup - Required Settings . . . . . . . . . . . . . . . 23
8. Jackpot Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8.1 Jackpot Configuration Procedure . . . . . . . . . . . . . . . . . . . 25
9. Machine Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
9.1 Service Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
9.1.1 Recommended Service Menu Settings . . . . . . . . . . . 31
9.1.2 Service Menu Overview . . . . . . . . . . . . . . . . . . . . 32
11. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
11.1 Jackpot Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
11.2 Change APL™ Master Machine . . . . . . . . . . . . . . . . . . . . 41
11.3 APL™ Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 42
12. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
12.1 Commboard Connectors . . . . . . . . . . . . . . . . . . . . . . . . 44
12.1.1 Commboard Connector Pin-out . . . . . . . . . . . . . . 45
12.2 Commboard DIP Switch Table . . . . . . . . . . . . . . . . . . . . . 46
12.3 How to identify the Software Level . . . . . . . . . . . . . . . . . . 47
2. Introduction
2.1 About this Manual
Scope
This document describes how to set up and configure a CASH
FEVER™ link. It describes how to set up the participating gam-
ing machines, how to link them and how to carry out the jack-
pot configuration and the display configuration.
Target Audience
We address qualified technical personnel, who are involved in
setup and configuration of a CASH FEVER™ link. With this user
group we assume that they are basically computer literate and
familiar with gaming machine and progressive jackpot termi-
nology.
Please read this document carefully before you start the set-
up, to avoid incorrect configuration.
Software Version
This document relates to display software version 3.02
(installation package CASH FEVER V3.02.00).
Related Publications
More detailed information about installation, basic setup and
operation of Atronic e-motion™ gaming machines may be
found in the following publications:
Installation Manuals
• Manual EMC - Installation
• Manual E - Installation
Operation Manuals
• Manual EMC - Operating (C4.x.x STD)
• Manual E - Operating (C5.x.x STD)
3. Overview
3.1 Preface
CASH FEVER™ is the ultimate concept in linked gaming from
Atronic and offers an amazing 4-level progressive jackpot.
All bonus games are played with the same number of lines,
bet per line and play modes as the game that triggered the
bonus session.
As the bonus games are played the credits are accrued on Dr.
CashFever’s Thermometer in the upper screen. Each of the 4
jackpots are triggered in turn when a specific number of cred-
its are awarded during the bonus games - the more credits
won during the bonus games the "hotter" the thermometer
becomes for bigger jackpot wins.
4. Setup
4.1 Atronic Progressive Link™ (APL™)
4.1.1 What is APL™?
The CASH FEVER™ links use Atronic Progressive Link™ (APL™)
technology to link the participating gaming machines. APL™
provides a very simple way to link Atronic games to a local
area progressive.
This figure shows the wiring diagram of a typical CASH FEVER™ APL™ link.
* If less than 16 EGMs are linked, the APL power supply can be connected at either ends of the link
or in the middle of the link.
** If 16 to 20 EGM are linked the APL power supply has to be connected in the middle of the link,
using a RJ-45 Y-adapter (Adapter WE8 - 2 WE8).
P17 P5
P18
Commboard 68k
Rev. 2.10 P9
B1
CPU 68k
U28
S9 P16
P3 12V
5V
SLAVE
P7 P15
P1 U34 U35
P12 P4 P19
Machine
P20
Data Controller
Battery 3.6V + P14 P10 (MDC)
P2 P13
0 0 0 0 0 0 ON ON
P11
1
1
7 89
7 89
7 89
7 89
7 89
7 89
2 34
2 34
2 34
2 34
2 34
5 6 5 6 5 6 5 6 5 6 5 6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
S1 S2 S3 S4 S6 S7 S5 S8
U28
S9 P16
P3 12V
5V
SLAVE
P7 P15
P1 U34 U35
P12 P4 P19
Machine
P20
Data Controller
Battery 3.6V + P14 P10 (MDC)
P2 P13
0 0 0 0 0 0 ON ON
P11
1
1
7 89
7 89
7 89
7 89
7 89
7 89
2 34
2 34
2 34
2 34
2 34
2 34
5 6 5 6 5 6 5 6 5 6 5 6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
S1 S2 S3 S4 S6 S7 S5 S8
Rev. 2.10 P3 P4
B1
nected
CPU 68k 1
U28
S9 P16
P3 12V
MASTER
5V
P7 P15
P1 U34 U35
P12 P4 P19
Machine
P20
Data Controller
Battery 3.6V + P14 P10 (MDC)
P2 P13
0 0 0 0 0 0 ON ON
P11
1
1
7 89
7 89
7 89
7 89
7 89
7 89
2 34
2 34
2 34
2 34
2 34
2 34
5 6 5 6 5 6 5 6 5 6 5 6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
S1 S2 S3 S4 S6 S7 S5 S8
Note: As connectors P10 and P11 on the commboard are wired parallel it does not matter which one is used
for input or output. However it is recommended to use this wiring pattern for ease of maintenance.
Required Settings
Optional Settings
Commboard 68k
1. Set an APL™ progressive address with rotary switches S1 Example: To set APL™ progressive ad-
and S2 on the commboard. Each machine in the link must dress “15”, set S1 to “1” and S2 to “5”
have a unique address from "01" to "20". Address "00" is
not valid.
S1 Set APL Progressive Address (x10)
S2 Set APL Progressive Address (x1)
4. Configure APL™ mode to APL2™ (on all machines in the Note: The Media Controller has to be
link). connected to the APL™ master com-
S5/5 OFF (recommended setting) mboard.
This enables communication on SAS channel 1 on com- Note: See chapter 12.1.1 "Commboard
mboard connectors P12 (RS-232 interface) and P2 (TTL Connector Pin-out" for a commboard
interface). connectors layout.
3. Optional: Close jumper B1 on the commboard. This short- Note: Close jumper B1 if you use an
cuts digital ground on commboard connector P12 to elec- Atronic Systems MDC.
trical ground.
This enables communication on SAS channel 2 on com- Note: See chapter 12.1.1 "Commboard
mboard connectors P4 (RS-232 interface) and P19 (TTL Connector Pin-out" for a commboard
interface). connectors layout.
S8/2
Allocates Progressive Jackpot Polls
Affected long polls: 80, 86
S8/3
Allocates EFT Polls
Affected long polls: 22-26, 28, 29, 62-67
S8/4
Allocates Legacy Bonusing Polls
Affected long polls: 2E, 8A, 8B
S8/5
Allocates Control Polls
Affected long polls: 03-07, 0A-0C, 94, A8
S8/6
Allocates Ticketing Polls and Exceptions
Affected long polls: 4C, 4D, 57, 58, 70, 71, 7D
Affected exceptions: 3F, 57, 67, 68
5.1 General
The media controller is a small PC that provides video anima-
tions and jackpot values which are displayed on the plasma/
LCD display(s). It comes with a pre-installed Windows® XP
Professional operating system (english version required) and
CASH FEVER™ display software. Two displays and an audio de- Note: Although an APL™ slave ma-
vice can be connected. The mains voltage for the media con- chine can send progressive jackpot
troller is provided by an Uninterruptible Power Supply (UPS). values to the media controller, it has
to be connected to the APL™ master.
The media controller receives the jackpot broadcasts from the Only the APL™ master can send the
APL™ master machine. It is connected by a RS485-to-RS232 trigger signal to start the jackpot hit
converter and a small commboard add-on board, the OH Dis- presentation.
play Board.
Important: The base stand or box where the me- Plasma/LCD Display
dia controller is situated has to be actively vented
to prevent the media controller from overheating.
Logic Box
EGM 1
5.3 Signage Cabling APL Master
The VGA cable, the audio cable and the signage mains cable
is usually threaded through one of the posts that hold the sig-
nage. You may need to temporarily remove the signage mains Vented Base Stand
plug to thread it through the post.
Media
UPS Controller
Mains
The plasma/LCD display(s) which are connected to the media Unit
controller have to support a 1024 x 768 pixel display resolu-
tion at 60 Hz with highest (32 bit) color quality via VGA (RGB)
or DVI connector.
This section describes how to connect the media controller. As Rev. 2.10 P9 P3 P4
B1
CPU 68k 1
the signage type may vary these steps are described in gen-
U28
S9 P16
P3 12V
eral.
5V
P7 P15
P1 U34 U35
P12 P4 P19
P10
(see also chapter 4.2 "Commboard Setup") and install the
Battery 3.6V + P14
P2 P13
1
7 89
7 89
7 89
7 89
7 89
7 89
2 34
2 34
2 34
2 34
2 34
2 34
5 6 5 6 5 6 5 6 5 6 5 6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
S1 S2 S3 S4 S6 S7 S5 S8
Not con
Rev. 2.10 P3 P4
B1
nected
CPU 68k 1
U28
P7 P15
the OH Display Board. P1 U34 U35
P12 P4 P19
P20
b) Connect the 14-pin terminal strip to connector P3 on Battery 3.6V + P14 P10
the commboard. 0 0 0 0 0 0 ON ON
P2 P13
P11
1
1
7 89
7 89
7 89
7 89
7 89
7 89
2 34
2 34
2 34
2 34
2 34
2 34
5 6 5 6 5 6 5 6 5 6 5 6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
S1 S2 S3 S4 S6 S7 S5 S8
Note: You may need to remove the cover from the serial plug
to thread the cable into the machine. VGA(2)
4. Connect the signage to the media controller. Mains
Input
a) Thread the VGA cable, the audio cable and the signage
mains cable through one of the posts that holds the
signage.
6. Machine Setup
This section describes how to carry out a RAM Reset and the
Initial Setup which is required to configure basic machine set-
tings and carry out jackpot configuration.
6.1 Overview
Atronic machines usually come configured as specified with
the order. However it may be necessary to re-configure basic
machine settings, such as denomination, metering, paytable,
etc. These settings can not be altered during normal opera-
tion, as they require a machine reinitialisation for technical or
jurisdictional reasons. Applying new progressive jackpot set-
tings also requires a RAM Reset.
3. Jackpot Configuration
After the Initial Setup has been carried out, it is necessary
to carry out the progressive jackpot configuration. Do not
insert credits before the jackpot configuration is done.
+
Replace the commboard EPROMs U34 and U35 with the P1 U6
commboard clear EPROMs "Q-CB-RAM-CLEAR" U34 and U7
U35. SD
U8
U22
U9
5. Reinstall mainboard and commboard and switch machine
power on. This step has to be carried out with the security
LED D19
device (SD) installed.
6. Wait (at least) until the Atronic logo and a progress bar
is displayed on screen. A flashing LED (D19) on the comm-
board confirms that the commboard clear was successful. P1 U34 U35
commboard. 0 0 0 0 0 0 ON ON
1
1
7 89
7 89
7 89
7 89
7 89
7 89
2 34
2 34
2 34
2 34
2 34
2 34
5 6 5 6 5 6 5 6 5 6 5 6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
S1 S2 S3 S4 S6 S7 S5 S8
HBS-STD-5.1.1.279
xxxx xxxxxxxxxxxxxxxxx
When the last setting has been configured, the Initial Setup
Summary page is displayed.
After the Initial Setup has been carried out the machine ini-
tializes and locks with the error message "APL: Configuration
Required". Proceed with the jackpot configuration which is de-
scribed in chapter 8. "Jackpot Configuration".
• Player Denomination
Do not configure more than one player denomination.
The denomination has to be identically on each machine
in the link.
Example:
Paytable 5-50-10-186
• Progressive Group
Leave the progressive group setting at "0" (default).
7.1 Alink™ Configuration Kit SUB -D - male connector SUB -D - female connector
• PC-Setup Cable
9 8 7 6 Solderside 6 7 8 9
(required, if the PC does not feature a serial port) Pinout PC-Setup Cable
• Software levels up to C4.2.x require Alink Config 2.6.6 Note: See also section 12.3 How to
• Software levels as of C5.x.x require Alink Config 3.02 identify the Software Level.
8. Jackpot Configuration
This section describes how to carry out the jackpot configu-
ration of a CASH FEVER™ link by means of the Alink Config
program. It allows to configure progressive jackpot param-
eters such as base value, increments, hidden jackpot and in-
machine display.
2. Connect the USB dongle and the setup cable to the com-
puter. If the computer does not feature a serial port to
connect the setup cable directly, use the USB-to-Serial
adapter cable. You have to install additional drivers for the
adapter cable.
At the computer:
Start the Alink Config program and select Download from
the Alink menu.
6. When the data has been loaded, the APL™ main menu is
displayed.
Setting Function
Player Denomination Option not used (fixed setting)
Currency Enter a 3 digit ASCII string, which is displayed trailing or
leading the JP value. Currency strings "EUR" and "USD"
are interpreted by the software and will display a "€"
respective "$" symbol.
Currency Position Select the position of the currency string.
Separator Style Sets the style of the thousand seperator and the deci-
mal separator. Select Standard (European style), US (US
American style) or Custom.
In-Machine Display Mark this checkbox to enable the in-machine display in The upper game screen with four jackpot meters
general. (in-machine-display).
Odometer Mark this checkbox to enable a smoth non-jumping
display of the jackpot values on the in-machine display
(optional).
Overhead Display Type Select Ataka display protocol to enable communication
to the Media Controller (mandatory setting).
Setting Function
Current Value Sets the initial progressive jackpot value that is dis-
(in currency) played directly after the jackpot configuration (usually
the same as the base values).
Base Value Option not used.
(in currency) CASH FEVER™ uses fixed base values.
Limit Defines the upper limit of the progressive jackpot value.
(in currency) Further increments are paid into the hidden jackpot or
the overflow. "0" = No limit.
Increment Percentage of credits wagered that accumulates to the
(in %) jackpot value.
Jackpot Name Option not used.
Text color Option not used.
Value color Option not used.
Jackpot Won Text Option not used.
Text Display Time Option not used.
Value Display Time Option not used.
Hidden Jackpot Mark this checkbox to enable a hidden jackpot (op-
tional).
Setting Function
Current Value Sets the initial hidden progressive jackpot value.
(in currency)
Base Value Option not used.
(in currency)
Limit Defines the upper limit of the hidden progressive jack-
(in currency) pot. Further increments are booked into the overflow
statistic. "0" = No limit.
Increment Percentage of credits wagered that accumulates to the
( in %) hidden jackpot value.
14. (optional) Click Save to save the settings to disk. The Save
As dialog box opens. Navigate to the folder where you
want to store the Alink™ configuration files and save the
file.
You can load these files into the program by clicking the
Load button in the APL™ main menu.
15. Click Upload from the APL™ main menu to send the con-
figuration data to the machine.
17. Unplug the setup cable and close and lock the logic box
and the maindoor.
18. Clear the "Logic Door Open - Turn Audit Key" message by
turning the Audit Key.
9. Machine Configuration
9.1 Service Menu
The Service Menu provides several settings and options that
can be adjusted during normal machine operation (see chap-
ter 9.1.2 Service Menu Overview"). To access the Service Menu,
open the maindoor and press the service button at front of
the logic box.
Celebration Limit
The celebration limit determines the threshold for jackpot
handpays (if Destination = Handpay). A win exceeding the
celebration limit initiates a win celebration and needs to be
acknowledged by an attendant using the jackpot key.
You may adjust the celebration limit settings to meet the re-
quirement of your operations.
To apply changes click the Save or the Save & Exit button.
• Thermometerloops
A complete animation sequence contains following parts:
long anim. -› JP meter -› short Dr. Cash Fever anim. -› JP meter -› long anim.
The duration of the two JP meter animations in this se-
quence is configured by the Loop1 and Loop2 setting. One
unit of the Loop parameter is approximately 4 seconds.
• Currency
Configures the currency abbreviation displayed trailing or
leading the progressive value.
• Background
Required setting - Do not adjust.
• Delimiter
Select a style for the delimiter symbols (dots or commas).
• Currency Position
Select if the currency abbreviation is displayed trailing or
leading the progressive value.
• Odo Size, Font Style, Odo Style, Frame Set, Offl. Msg.
Required settings - Do not adjust.
• Digits
Defines how many digits are displayed in front and behind
the comma or dot.
• No. of Meters
Required setting - Do not adjust.
The Hit Config menu does not contain any items that should
be adjusted by operators.
10.1.3 Messages
• Helpmovie
Allows to activate or deactivate the CASH FEVER™ help
movie and to adjust the language of the help texts.
• Offline
Option not used.
10.1.4 Audio
10.1.5 Template
10.1.6 About
• HCB-Q_-S5-MR-STD_-E-08A
• HCB-Q_-S5-MT-STD_-E-08A
• HCB-Q_-S6-MG-STD_-F-08A
• HCB-Q_-S6-MH-STD_-F-08A
1. Press the Esc key to close the display software. The display
software closes and the Windows® desktop is displayed.
• HCB-Q_-S6-xx-STD_-1-08A
• HCB-STD-12.x.x.xx (or higher)
you do not have to edit the serial.ini file. This versions use the
default "feature" handling.
11. Maintenance
11.1 Jackpot Statistics
This section shows where to find the different progressive Note: All figures in this pictures are for
jackpot statistics of an APL™ link. example only!
Jackpot Statistics
(Audit Menu / History / Cashless and Progressive / Jackpot Statistics)
Progressive Table
(Audit Menu / History / Cashless and Progressive / Progressive Table)
Alink Status
(Service Menu/Diagnostics/Other Tests/Alink Status)
This menu shows the status (Master, Ready, N/A) of all ma-
chines in the link.
APL: Progressive Not Connected / APL: Master not ready Note: This message is also displayed
• The machine is not connected to the APL™ master ma- on all APL™ slave machines prior to
chine. the jackpot configuration. The mes-
• The APL™ power supply is not connected. sage expires when the APL™ master
• No APL™ master is defined in the link. machine is configured.
• APL™ master machine is down.
Solution:
• Check the cabling and make sure the link is set up cor-
rectly.
• Connect the APL™ power supply.
• Define one APL™ master machine in the link.
• Power up the APL™ master machine.
12. Appendix
12.1 Commboard Connectors
The Atronic commboard 68k Rev. 2.10 features several con-
nectors for different systems and protocols.
P17 P5
P18
P9
B1
CPU 68k
U28
S9 P16
P3 12V
5V
P7 P15
P1 U34 U35
P12 P4 P19
P20
1
7 89
7 89
7 89
7 89
7 89
7 89
2 34
2 34
2 34
2 34
2 34
2 34
5 6 5 6 5 6 5 6 5 6 5 6
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
S1 S2 S3 S4 S6 S7 S5 S8
This chapter describes the connectors pinout of the SAS based Note: See manual "Commboard 68k"
connectors. for other connectors and further de-
tails.
Connector P12
Function: SAS protocol / Channel 1
Interface: RS232
1 2 PIN Function
3 RXD
4 RTS
5 TXD
6 CTS
9 10
9 SAS Ground
10 SAS Ground
Connector P2
Function: SAS protocol / Channel 1
Interface: Current loop (TTL)
4 PIN Function
3 1 SAS +5V or SAS +12V or none (depends
2 on voltage switch S9)
1 2 RXD
3 TXD
4 SAS Ground
5 PIN Function
2 parallel wired to P4 / pin 5 (TXD)
4 parallel wired to P4 / pin 3 (RXD)
1 5 Ground
S2 EGMs APL Progressive System Address x01 Address "00" disables APL™ progressive address
S3 EGMs Accounting System Address Channel 2 x10 Note: Set commboard system ad-
S4 EGMs Accounting System Address Channel 2 x01 Address "00" disables channel dress on channel 1 to 01, if a slot
machine interface board (SMIB) or a
S6 EGMs Accounting System Address Channel 1 x10 machine data controller (MDC) pro-
S7 EGMs Accounting System Address Channel 1 x01 Address "00" disables channel vides the system address.
1 2 3 4 5 6 7 8 Function
Off Off Off Mikohn MS-10 Progressive (use this setting for non-progressive mode)
On Off Off Accounting / System Progressive
Off On Off APL Progressive / APL CASH FEVER™
On On Off Mikohn MS-27 Mystery
Off Off On Mikohn MS-27 Mystery + Progressive
On Off On Accounting System 3rd Channel
DIP Switch S5
HBS-STD-11.1.2.81