Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. Engine Block
- Engine block is an important parts of an engine. It is made by pouring the molten iron or aluminum
alloy into a mold. The mold is made such that we should have required number of holes in the casted
block, which are said to be the number of cylinders of an engine or engine cylinders. The diameter of
these holes is called the bore of an engine.We have some more holes along the length of engine cylinder,
these are water and oil flow paths required for cooling and lubrication of an engine. Oil paths or vents are
rather narrower than water flow vents.What else we have in an engine block is semi-circular seats. On
these seats half part of thrust bearings (thrust bearings come in two parts) are mounted, then we place
crankshaft in these thrust bearings. But we still need to hold crankshaft to the engine block, to do that we
have bearing-caps.Bearing-caps have a semi-circular seat for other half part of thrust bearing. To mount
the bearing-cap with engine block we use studs and nuts. One threaded end of stud goes into internal
threaded hole in engine block, and other threaded end of stud goes into hole in bearing-cap and we fasten
them together with nut. Two studs are used for holding one bearing-cap in place.
2. Piston
-Piston is a cylindrical structure with a flat surface called crown at the top. Piston is the component that
moves up and down in an engine cylinder. Wait what it would cause?, friction if one cylinder (piston)
moving up and down in another cylinder? Yeah to overcome this problem groves are made on the
circumference of this cylindrical structure (piston). And we place rings in these groves called piston rings.
So now the whole cylindrical structure is not rubbing with engine cylinder and only piston rings are in
contact with engine cylinder thus reducing friction to a great extent.Now how we go to use this up and
down motion of piston, for that we need to know about 2 more things that are connecting rod and wrist
pin.
3. Connecting Rod
-It is an ‘I’ shape structure whose one end is connected to piston and other one to crankshaft. The piston
side end of connecting rod has hole in it. And we have also got a hole in piston’s cylindrical structure just
beneath the piston rings. So we align this hole with connecting rods hole and put a wrist pin through it.
Wrist pin act as a bearing and connecting rod can move like pendulum beneath piston, though piston’s
cylindrical structure is gonna limit its motion. To make sure that wrist pin should not move from its
position it is restricted by snap ring at both sides.Other end of the connecting rod can be split into two
parts. First is semi-circular journal bearing seat, which is placed over crankshaft after installing the half
part of journal bearing, in the seat. Other half is journal bearing cap. These two parts are bolted together,
holding crankshaft in between. Thus piston is now connected to crankshaft through connecting rod.
4. Crankshaft
-As name suggests it is designed in such a way to convert linear (up and down) motion of piston into
rotational motion. It works same as slider- crank mechanism. Material used for making crankshaft is cast
iron generally but we also use forged steel in high power engines where load on crankshaft is too
high.Casting a crank-shaft seems to be an easy task, but it’s not. Once crankshaft is casted it is then
machined, which is not that easy considering its shape. Then after machining it requires proper balancing
to work properly.You will generally find some random holes in crankshaft; these holes are for balancing
the crankshaft while rotating at high speed.
5. Crankshaft Casing or Oil Sump
-It is also called as oil sump. It is a casing which is bolted to engine block, which covers engine from
bottom thus called crankshaft casing. It retains lubricating oil in it which is pumped to different engine
parts. Crankshaft has got small holes which spills oil towards piston, to remove piston heat and lubricate
the piston rings, so it also prevents oil from splashing. We have got a bolt at the bottom of this casing
from where we remove used lubricating oil during maintenance.
6. Engine Head
-Engine head is casted in the same way as engine block. Its mold is made such that the casted piece
must have an opening for air to flow into engine cylinder and an exhaust opening from where the burnt
gases will go out. This passage of air flowing in and going out of engine cylinder is controlled by inlet and
outlet valves. So engine head also has cylindrical holes to insert valve stem. Furthermore to burn the air-
fuel mixture we have to fire it up and how we gonna do that? Yeah we need a spark plug which must
produce a spark inside engine cylinder, for this we need cylindrical hole in engine block to put spark plug
into engine cylinder. We also have semi-circular seats casted in engine head for camshaft bearings.
7. Valves
-As we have already know that they control the inlet and exhaust air to go into and out of engine
cylinder. Material used to make valves is nickel-chromium iron alloy. It can resist high temperature and
have great strength. Valve could be described in two parts- valve stem and valve head. As we already
know that we have got cylindrical hole in engine head for valve steam and we also have a valve seat
where valve head will rest in engine head. Valve is mounted upside down means valve head is facing
engine cylinder. It is so because when there would be high pressure in engine cylinder it would press the
valve head against its seat in engine head and thus pressure will be maintained at best.
8. Camshaft
-it is a shaft with a number of cam profiles along its length. So it regulates the valves opening and closing
time. It does so by pressing the end of valve stem by its cam profile. But we still need a mechanism which
would return the valve back to its position once pressed by the cam profile of camshaft. We have valve
spring and bucket head tappet assembly for solving this problem.Now as we have semicircular seats for
bearings of camshaft. What retains it to be fixed in engine head while rotating is cam-caps? They hold
the other half of journal bearing and have two holes in their casing through which we insert bolts and
fasten them in internally threaded holes of engine head thus we hold our camshaft between the casted
journal seat in engine block and cam-caps and fasten them up with long bolt.
12. Gasket
-A wide variety of materials are used in making gaskets like Teflon, glass-fiber, silicon etc. It is generally a
paper like sheet which is placed between engine block and engine head. As we have already discussed
that we have both water and oil vents in engine block, so gasket gives insulation from water or oil
leaking into engine cylinder or air-fuel mixture from engine cylinder leaking out from joint of engine
block and engine head. Aluminum engine blocks are preferred over cast iron because it expends more
on heating thus compressing the gasket more, increases the workability of gasket, thus reducing the
chances of leakage.
2. Piston
3. Connecting Rod
4. Crankshaft
6. Engine Head
7. Valves
8. Camshaft Camshaft
9. Valve Spring and Tappet
12. Gasket