nvlad te caLisraTiO® contration NWLAP LAD CODE 1osC%e Certificate of Calibration Fluke Park Laboratory Description: Field Metrology Well with Process Readout Gontificate Number: 85407046 Manufecturer: Fluke Date of Calibration: 97 Out 2018 Model: 9142 Date Due: Serial Number; B6Ag68 Temperature: 20.010 260°C Status: As-Found: New Relative Humidity: 2010 70 %RH As-Left: In Tolerance Pressure: 9510 103 kPa Calibration: Full Issue Date: 97 Oct 2028 Procedure: HCT303 -1 Customer INTERWORLD HIGHWAY LIC JONESTOWN PA, PONumboer 126031 ‘This ealioration is traceable to the Si through recognized national measurement insttutes (NIST, PTB, NPL, NIM. NRC. etc.) ratiometnc techniques, or natural physical constarts and (s in comoliance with ISONEC17026:2006 and ANSINCSL 2540.1. The calibration has been completed im accordance with the Fluke Corporate Quality System document OSD 111.0. Calibration cerifieatos without icentiicabon ef the authorizing person ate not vale) This Cerificate applies to only the item identified and shall not be reproduces other than in ful without the specie written approval by Fluke Corporation ‘his calibration ceriffcate may contain data that is not covered by the Scone of Accredtation “The unacereaited {est points, where applicable, are indicated by an asterisk (*), sr confined to cleanly marked sections the Gertiicate shall rot be used to claim product cerification, approval, or endorsement by NVLAP. NIST ar any agency of the US. Government Measurement uncertainties at the time of test are given where applicable; They are caleviated in accordance with the mathed desenbed in the ISO Guide to the Expression of Uncertainty in Measurement The reported expanded uncertairty ol measurement is staled as the stangarc uncertainty of measurement muttipied by the coverage factor k such that the coverage provabilty corresponds lo approximately 38 %b Comments: ae tft Miceee =f I Electronically signed by Sees ef ‘Approved Signatory Sin Rana £ ‘vars tkstrums Pt ae Metrologist Fluke Corporation Telephone Internet Page ofa 6920 Seaway Blvd 877.355.3225, www flukecal. com Rev 20160922 Everett, WA 98203 USACertificate Number: 86407046 Date of Calibration: 07 Oct 2018 Standards Used Description Serial nucber Due-pare 256€ Digital thereoueter A263 1568 Therroneter, “Black Stack” sase unit Fos2s 2862-4 Precision Digitol Thermonete- 9807 2502-H Precision Digital Tnermoneten 5628 Platinue Resistarce Thenmonere” 5628 Platinun Resistarce Theraometer 2529-K ThermonPTe”, Chud-£4, 4-PRT /Therai ste 5618 Thereistor Prone 690202 5610 Thermistor Prabe an2z908 24-Nov-2817 5780 OC Reference Standard 555607 23-wov-2017 748A Standarc Resistor Set asn602 Fielé Metrology wall test stetios : Quality Manuals This calibration has been completed in accordance with ©The Fluke Corporate Quality Manual, QS0 111.0, Revision 118. Dated August, 2017 and/or © The Fluke 17025 Quality Manual, QSD 131.42, Revision 005, Dated Sent. 2017 The Instrument described herein consists of @ heat source component and a built-in process readout component ‘This calibration pertains to both components The heat source component was calibrated by direct measurement of generated temperatures using the pertinent felerence standards listed in the "Test Equipment” section of this resort. The calibration was performed using test insert Model 914x-INST ox described in the user manual This insert is similar to inser °C but is designed to accommodate the test PRTS and aid in the pertormance of the axial gradient calibration. the calibration ata, internal calibration constants, and uncertainties are stown on the following page(s) ofthis report. The temperature accuracy test fs self-explanatory. The axial differential temperature test is more complex. Due to the nature of the axial diferential temperature characteristic and the influence of the test equipment on the test result, this test utiltes tolerances which do not precisely match the instrument specification. However, the unique tolerances used are intends to determine the axial ciHerential temperature tolerance status based on the published specifications ‘The temperature observations were performed in both Increasing and decreasing directions The process readout component was calibrated directly using laboratory transfer standards as listed in the "Test Equipment” section of this report. The calibration data, internal calibration constants, and uncertainties are shown an the following pagets) of this report ‘The calibration uncenainties are shown at a coverage factor of 2 (k=2). All known significant sources of uncertainty have been considered. Any limitations or remarks pertaining to this instrument and/or Calibration are shown below. ‘Additionally, out of tolerance indications, i any, are identified along with the corresponding data on the data pages of this report, Calibration uncertainties have been taken into account in the determination of tclerance status using Fisk analysis elgorithms. When using the Instrument jn a calibration process, it is recommended that the instrument specifications be used as the contribution of the instrument rather than the calibration uncertainties, The instrument tolerances are shown on the report at @ confidence interval af 95% ‘The sections labeled Temperature Stability, Axial Diferential Temperature and/or Maximum Hysteresis contain data that are not covered by the NVLAP Scope of Accrecitation, Page 2 of 4Mode! 9142 Seria! No. S6AB58 Ceriticate No B6AG70<8 ‘As Found Dats No As Found Data Requis Certificate of Calibration As Left Data Data 10: 86220115507327 Galiration Corstanis Temperature Accuracy TEMP 1 = 0.099 Set-point °C Actual *C JEMP2 -o194 “280006 24.984 TEMPS -0342 0.000 -0.007 GRAD I -0014 2.009 45.995 GRAD2 0016 100.000 so0013 GRAD3 0.000 160.000 149.985 Temperature Siabity Observed °C Control Constants Set-pant"C | __@ Sigma) TEMP PB. 20 21008: wee TEMP INT 310.0 eee pone TEMPORR 1.0 ‘cal Diflerantia Temperature Sorpaint’C Target“ Actuet “0 ‘0.000 0.000) 0.000 2.000 0.003 100 000 oor 0.004 10 000 oor0 ots. Error°c 2016 0.007 0.005 nts 0.005 Tolerance °C 0.010 20.040 Eror“c 0.009 0.003 0.008 0.008 Tolerance *C 30.200 20.200 0.200 9.200 0.200 Uncertainty Passiait Uncenainty ‘70.0040, 40,0085 30.025, 30.025 20025 40.030 10.030 apuey PassiFai P > Toleiance “C_Uncenanty _PassiFail 20.040 0.040 20.040 20.040 #0020 e 20020 P 20028, Pp +0030 Pp This port shall not be procured except uf withoul writen approval of Fluke Calibration Page 3 ot 4