Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
VAPORSTOP CA 500
ULTRAFLEX SA NBS
ULTRAFLEX SA
ULTRAFLEX SA NB
ULTRAFLEX SA 1.5 mm STRONG P
ULTRAFLEX SA 1.5 mm STRONG G
APPLICATION AREA:
Waterproofing of underground (below-grade) parts of premises and Quick installation Cold application
engineering structures prevents smoke,
Indoor waterproofing of premises and buildings odors and noise
Waterproofing of confined area, where standard technologies
cannot be applied (bathroom floor). Can be used in parquetry and
floor installation Self-adhesive waterproofing is a type of materials, that combines all
As an underlay on pitched roofs and as a vapor barrier on the advantages of torch-on applied materials and non-torch-on
the corrugated steel sheets and precast concrete slabs installation, which helps to avoid issues associated with the use of
Corrosion protection of steel pipes and junctions flame.
2
VAPORSTOP CA 500
3
VAPORSTOP CA 500
SOLUTION EXAMPLES:
4
VAPORSTOP CA 500
METHOD OF APPLICATION:
Convenience, simplicity and safety of installation of the membrane are due to the special adhesive polymer-bitumen layer, which allows
installation of the material without additional equipment.
1 2 3 4
Cut the siliconized anti-adhesion Remove the protective film from Press the place of the first Continue attaching membrane to
film at the distance of 30-40 cm the edge of the roll and attach adhesion by roller for the whole the base. One worker pulls
from the beginning of the roll by the membrane to the surface. width of the membrane. the film off, while the other
means of roofing knife. smooths the membrane by brush.
5
ULTRAFLEX SA NBS
Used for indoor waterproofing with the direct installation of ceramic Material is installed in one
tiles onto the material without the need of protective sand cement layer unlike cement based
screed (spunbond has to be treated with the contact primer before waterproofing, which requires
application of tile adhesive). Can be used on bases, where the several layers
standard torch-on application is forbidden (wood, XPS, etc.). No need to wait for the screed
to dry
MATERIAL STRUCTURE: Tiles are installed directly on
the material
1. Polypropylene (Spunbond)
Protects waterproofing layer from mechanical damage. Provides
strong sticking of the tile adhesive when treated with the contact
primer PROPERTIES ULTRAFLEX SA NBS
2. Self-adhesive polymer-bitumen compound Mass per unit area, kg/m2 1.5±0.25
High elasticity index of this layer allows installation of the
Thickness, mm 1.5±0.10
membrane on surfaces of any complicated shape
3. Easy-removable protective film Flexibility / Flow resistance, °С ≤-15 / ≥85
Used for underside surface protection from sticking in the roll Tensile strength, N/50 mm NPD
Length x width, m 20 × 1
6
ULTRAFLEX SA NBS
SOLUTION EXAMPLES:
7
ULTRAFLEX SA
ULTRAFLEX SA ADVANTAGES:
MATERIAL STRUCTURE:
1. PE film or sand
Protects waterproofing layer from mechanical damage and
prevents adhesion of the material in the roll PROPERTIES ULTRAFLEX SA
2. Polymer-bitumen compound Mass per unit area, kg/m2 1.8±0.20
Provides reliable waterproofing
Thickness, mm 1.5±0.20
3. Polyester
Provides excellent elongation and grants optimal strength to Flexibility / Flow resistance, °С ≤-20 / ≥90
the material
Tensile strength L / T, N/50 mm 400±100 / 300±100
4. Self-adhesive polymer-bitumen compound
Self-adhesive layer allows to install the material on combustible Reinforcement type polyester
surfaces Protective covering type: top / bottom polymer film or sand / anti-adhesion film
5. Easy-removable protective film
Length x width, m 20 × 1
Used for underside surface protection from sticking in the roll
8
ULTRAFLEX SA
SOLUTION EXAMPLES:
9
ULTRAFLEX SA NB
ULTRAFLEX SA NB ADVANTAGES:
MATERIAL STRUCTURE:
10
ULTRAFLEX SA NB
SOLUTION EXAMPLES:
11
ULTRAFLEX SA 1.5 mm STRONG
MATERIAL STRUCTURE:
SOLUTION EXAMPLES:
13
METHOD OF APPLICATION
1 2 3 4
Clean and treat the surface with Fit and straighten the membrane Re-roll the membrane to the Remove the protective film and
bitumen primer. to the area of application. center, pre-cut the protective film. smooth the membrane.
14
METHOD OF APPLICATION
15
METHOD OF APPLICATION
FOUNDATION WATERPROOFING
1 2 3 4
Surface must be smooth, dry, Measure the depth of the Apply the material from top The material to be installed to
clean and with no oil stains. For foundation and cut the material to downward by gradual removing the height of 30-50 cm above
better adhesion, treat the surface the required length. the protective film, unrolling the ground level. Longitudinal
with primer. the membrane and smoothing it overlaps should be 100 mm,
to the surface. sheet end overlaps - 150 mm.
16
METHOD OF APPLICATION
FOUNDATION WATERPROOFING
5 ! !
The top end of the waterproofing Protect the membrane from As a protection from mechanical
membrane to be fixed at mechanical damage by means of impacts, one can also use
basement level by profiled metal thermal insulation or protective PLANTER HDPE membrane.
edge strip and sealed. slabs.
17
THANK YOU FOR ATTENTION!
WWW.TECHNONICOL.IN