Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
FlexMove
Direct Drive Motor Selection
SAF[ SEW Part No ], i=[ Gear Ratio ]-M1B-Flange=120mm- SAF[ SEW Part No ], i=[ Gear Ratio ]-M1A-Flange=120mm-
Shaft=20mm-TBox=0-Cable=X Shaft=20mm-TBox=180-Cable=X
Speed, * Gear Ratio, Speed, Torque, Power, * SEW Part No. Estimated Series
m/min i rpm Nm W Drive Diameter = 171mm Traction Force, N
* Maximum Traction Force = 500N for FK & FS (Always set limit value of driving current or torque limiter)
Speed, * Gear Ratio, Speed, Torque, Power, •SEW Part No. Estimated Series
m/min i rpm Nm W Drive Diameter = 171mm Traction Force, F
* Maximum Traction Force = 1000N for FM, FC & FL (Always set limit value of driving current or torque limiter)
FlexMove reserves the right to make alteration without prior notification Every care has been taken to ensure the accuracy SEW Gear motors are products of SEW Eurodrive.
of the information contained in this catalogue but no liability can be accepted for any error or omissions.
9.8 20-1
R
FlexMove
Suspended Drive Motor Selection
S[ SEW Part No ], i=[ Gear Ratio ]-M1A-Shaft=20mm- S[ SEW Part No ], i=[ Gear Ratio ]-M1B-Shaft=20mm-
TBox=0-Cable=X TBox=180-Cable=X
Speed, * Gear Ratio, Speed, Torque, Power, •SEW Part No. Estimated Series
m/min i rpm Nm W Drive Diameter = 171mm Traction Force, N
* Maximum Traction Force = 500N for FK & FS (Always set limit value of driving current or torque limiter)
Speed, * Gear Ratio, Speed, Torque, Power, •SEW Part No. Estimated Series
m/min i rpm Nm W Drive Diameter = 171mm Traction Force, F
* Maximum Traction Force = 1000N for FM, FC & FL (Always set limit value of driving current or torque limiter)
FlexMove reserves the right to make alteration without prior notification Every care has been taken to ensure the accuracy SEW Gear motors are products of SEW Eurodrive.
of the information contained in this catalogue but no liability can be accepted for any error or omissions.
9.8 20-2
R
FlexMove
Intermediate Direct Drive Motor Selection
SAF[ SEW Part No ], i=[ Gear Ratio ]-M1B-Flange=120mm- SAF[ SEW Part No ], i=[ Gear Ratio ]-M1A-Flange=120mm-
Shaft=20mm-TBox=0-Cable=X Shaft=20mm-TBox=180-Cable=X
Speed, * Gear Ratio, Speed, Torque, Power, * SEW Part No. Estimated Traction Series
m/min i rpm Nm W Drive Diameter = 101mm Force, N
* Maximum Traction Force = 500N for FK & FS (Always set limit value of driving current or torque limiter)
Speed, * Gear Ratio, Speed, Torque, Power, * SEW Part No. Estimated Traction Series
m/min i rpm Nm W Drive Diameter = 138mm Force, N
* Maximum Traction Force = 1000N for FM, FC & FL (Always set limit value of driving current or torque limiter)
FlexMove reserves the right to make alteration without prior notification Every care has been taken to ensure the accuracy SEW Gear motors are products of SEW Eurodrive.
of the information contained in this catalogue but no liability can be accepted for any error or omissions.
9.8 20-3
R
FlexMove
Intermediate Suspended Drive Motor Selection
S[ SEW Part No ], i=[ Gear Ratio ]-M1A-Shaft=20mm- S[ SEW Part No ], i=[ Gear Ratio ]-M1B-Shaft=20mm-
TBox=0-Cable=X TBox=180-Cable=X
Speed, * Gear Ratio, Speed, Torque, Power, * SEW Part No. Estimated Series
m/min i rpm Nm W Drive Diameter = 101mm Traction Force, N
* Maximum Traction Force = 500N for FK & FS (Always set limit value of driving current or torque limiter)
Speed, * Gear Ratio, Speed, Torque, Power, * SEW Part No. Estimated Series
m/min i rpm Nm W Drive Diameter = 138mm Traction Force, N
* Maximum Traction Force = 1000N for FM, FC & FL (Always set limit value of driving current or torque limiter)
FlexMove reserves the right to make alteration without prior notification Every care has been taken to ensure the accuracy SEW Gear motors are products of SEW Eurodrive.
of the information contained in this catalogue but no liability can be accepted for any error or omissions.
9.8 20-4