Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Cicol ET Screed provides an extremely hard wearing anti-skid Fully cured Cicol ET Screed has been shown to be resistant
surface to a variety of substrates including concrete and to petrol, kerosene, diesel, hydraulic fluids, dilute mineral
timber, ideally suited for car parks, walkways, wet work acids, alkalis and de-icing salts after continuous immersion
o
industrial areas etc. for 12 months at 20 C
Surface preparation
Hard wearing.
Excellent adhesion to prepared asphalt surfaces and Cicol ET Screed can be applied to a variety of substrates.
primed concrete substrates. As with all flooring materials or protective coatings. Correct
surface preparation is essential.
Non-slip and excellent grip even when wet.
Concrete substrates
Chemically resistant to oils, greases, hydraulic fluids and
many other chemicals. Cicol ET Screed is applied to clean, sound, dry concrete
substrates which are free of any laitence, or loose particles.
Waterproof - excellent corrosion protection to concrete Mechanical scarifying or blasting methods are strongly
substrates. recommended. Prepared concrete substrates should be
o primed with Nitoprime 30 and Nitoprime 31.
Fast cure - foot traffic after 24 hours at 25 C.
The primer is applied by lambswool roller to provide a thin
Description even coverage. Avoid over application and puddles Cicol
ET Screed is applied on to the primer whilst it is still wet.
Cicol ET Screed is a four component system based upon
solvent free, coal tar modified epoxy resins, amine curing Asphalt substrates
agents, chemically inert, graded silica fillers and a specially
selected silica aggregate of high crushing strength. The Cicol ET Screed can be applied onto asphalt substrates
components of Cicol ET Screed are supplied in pre-weighed provided they are clean, sound and dry. It is also
quantities ready to use on site. recommended that asphalt should be at least 12 months
old. The asphalt should be lightly grit blasted and/or
thoroughly degreased to remove any weakly bonded or
Technical support contaminated material to provide the desired surface. No
primer is required on asphalt.
Fosroc offers a comprehensive range of high performance,
high quality flooring, jointing and repair products for both new Wooden substrates
and existing floor surfaces. In addition, the company offers a
technical support package to specifiers, end-users and Cicol ET Screed can be applied directly on to clean, dry
contractors. timber substrates.
Cicol ET Screed is designed for application at a nominal Mix the two liquid components base and hardener
thickness of 5 mm. thoroughly using a forced action mixer such as a rectangle
or zyklos. Add the mineral fillers along with the aggregate
component and mix until a homogenous trowellable
Properties consistency is formed. The total mixing operation should
o
take about 5 - 7 minutes. The Cicol ET Screed is now
Pot life at 25 C: 40 minutes ready to for use. Do not add thinners or solvent.
o
at 35 C: 25 minutes
Specific gravity: 2.0 approximately
o
Curing time at 25 C: 24 hours for foot traffic
48 hours for vehicular traffic
o
at 35 C: 16 hours for foot traffic
36 hours for vehicular traffic
Page 1
Cicol ET Screed
Laying Coverage
2
Once mixed the Cicol ET Screed must be used within the Cicol ET Screed: 3.1 m /pack at 5 mm
specified pot life. Cicol ET Screed is laid whilst the primer is thickness
2
still tacky. Nitoprime Primer 30/31: 5 m /kg
Binder: 4.5 kg
Filler: 10.50 kg
Aggregate: 16.00 kg
Total: 31.00 kg
Nitoprime primer: 1 and 5 kg packs
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
www.fosroc.com Khamis Mushayt Tel: (07) 250 0469 Fax: (07) 250 0469 CSD Tel: (02) 608 0999 Fax: (02) 638 0693
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2 FO SA/CICOL ET SCREED/05/A