Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Movement detection with Light sensor for constant lux and daylight-link control
absence timer Trios Luminaires are initially set to maintain a nominal 500 lux on
Trios Luminaires can include movement working areas. Any deviations can easily be corrected with an infrared
sensors to detect when someone walks into a transmitter. In areas with little or no daylight (constant lux mode),
room.The lamp then immediately switches to a preset lux illuminance levels are maintained throughout the system’s
level. When no one is present the lights gently turn down to save maintenance cycle, regardless of lumen depreciation caused by dirt
energy and then switch off if the area remains unoccupied. Lights in accumulation or lamp aging.This eliminates the need for over-lighting
corridors and staircases can be prevented from switching off when and therefore minimises energy wastage. In areas with good daylight,
they are set in the security lighting mode. lux levels are maintained by turning lights down when daylight levels
increase. Lights automatically switch off when the measured lux level
Lights switch back on when daylight levels drop below the defined
commissioning
their lighting system. Lights can be switched from multiple points and
transmitter.
Luxsense
needed.
Lighting Controls Trios, luminaire based
LRL 1220
Luminaire-based illuminance
19 sensor for direct control of HF
regulating ballasts. It gradually
reduces the light output of the
luminaire when the illuminance
25
level on the working plane under
the luminaire increases over a
selectable level due to further
Ø 15 increasing daylight.The unit is
connected to the 1-10 V DC
Type Weight (kg) EOC
control input of regulating ballasts. LRL1220/00 0.02 56082799
LRL 1220/00
LRH 1221/00, LRH 1222/00
Lamp clip 'TL'D or 'TL'5 plastic
19 ∅ 24.5 19 ∅ 21 mounting clip, intended to mount
the luminaire based light sensor
LRL 1220 to a 'TL'D or 'TL'S size
fluorescent lamp.
The use of this clip eliminates the
42
35
need for mechanical provisions or
adaptations to the luminaire or
19 the optical system and facilitates
19
easy lamp replacement.
IRR 1224
Infrared receiver, intended for
luminaire based mounting.
19 19
The receiver can be clipped onto
the lamp using lamp clips LRH
1221 or LRH 1222. Alternatively
the unit can be mounted with a
18 metal bracket (to be provided by
the luminaire manufacturer).
Connection is done with a 1 m.
long connection cable, provided
Type Weight (kg) EOC
with a standard modular plug. IRR1224/00 0.02 51715500
IRR 1224
Lighting Controls Trios, luminaire based
51 LRI 1110
Luminaire-based multi-sensor
incorporating an infrared receiver
for remote control, a light sensor
for ambient light monitoring and
52
a passive infrared detector for
movement detection. It has to be
used in combination with the
LCC 1130/10 controller and is
fitted with cable and plug for
32
connection to the modular input
Type Weight (kg) EOC
socket of the controller. LRI1110/10 0.20 55809100
LRI 1110/10 Dimensions in mm
LLC 1130 fixed.The LLC 1130/10 has to be
Luminaire-based controller for used in combination with the
148 switching high-frequency or luminaire-based multi-sensor
conventional ballasts, with LRI 1110/10.
maximum switching load of 150
VA.The unit has a special output
40
The Trios system is completed with a selection of the following General Purpose Components.
Infrared transmitters Page
IRT 8060 511
IRT 8065 511
IRT 8070 511
IRT 1090 500
IRC 2130 511