Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
BACK-UP QUOTATION
Issued for Construction
DCP 1.0
Kingdom of Saudi Arabia
Royal Commission for Jubail and Yanbu
Royal Commission in Jubail
TABLE OF CONTENTS
ITEM DESCRIPTIONS
A. uPVC/cPVC/PVC PIPE
B. THERMAL& MOISTURE PROTECTION
C. READY MIX CONCRETE
D. REBARS
E. PRECAST CONCRETE
F. CONCRETE MASONRY UNITS
G. VALVES & MOTOR OPERATED VALVES
H. ELECTRICAL CABLES
I. TERMITE CONTROL
J. ELECTRICAL FIXTURES
K. ASPHALT
L. DOORS & WINDOWS
M. GYPSUM BOARD
N TELECOM MATERIALS
O. FURNITURE
P. TRANSFORMERS
Q. PILES
R. STEEL STORAGE TANKS
S. FIRE SUPPRESSION SYSTEM
T. PUMPS
U. GENERATOR SET
V. GRE/RTR/GRP PIPES
W. OVERHEAD CRANES & MONORAIL HOIST
X. CHLORINATION SYSTEM
Y. ROAD MARKINGS
Z. VARIABLE FREQUENCY DRIVE
A.A. D.I PIPES
A.B. FUEL STORAGE TANKS
A.C. SECURITY FENCE
A.D. HVAC
A.E. SEC CHARGES
A.F. SANITARY MANHOLES
A.G. WATER METER
A.A.TURKI CORPORATION
CONSTRUCTION MATERIALS DIVISION
Q U O T A T I O N
To: RADICON-GULF CONSULT & Quote Ref: 4-03-RGCK-13 Date: 4 MARCH 2013
KENTZ ENGINEERING Your Ref: RGCK-(027-T15)-10FX-025 Date: 2 MARCH 2013
We thank you very much for giving us the opportunity to quote for your requirements. Following is our best
offer for your favorable consideration:
We trust that our offer meets your interest and looking forward to receive your valued order soon.
RENATO A. ESPEJON
SENIOR SALES ENGINEER
Mobile No. 050-773 2904
E-mail : renato.espejon@atco.com.sa
General Terms :
materials’ price such as aggregate, cement etc. we reserve the
right to increase the price according to its’ proportion.
2. Payment : Cash upon Confirmed Purchase Order.
3. Delivery : 8 days after receipt of your confirmed P.O. on partial delivery
basis.
4. Transport : Free Upto your Project Site at R.C. Jubail Area.
If you need any further information / clarification in this regard, please feel free
to contact us.
Assure you of our best service & prompt attention at all times.
Thanks & regards,
MOHAMMAD ZUBAIR KHAN
Plant Manager
QUOTATION
To: Radicon-Gulf Consult & Kentz-Engineering Date: 21-Feb-2013
Attn: Mr. John Coady Fax: 03 857 4420
Sub: YOUR REF: RGCK-(202-T15)-09-FX-405 Pages : 1+1
OUR REF: OAQ/110711/02-rev.1
Project: Mechanical Materials for Royal Commission Project - RC Proj. Cont. 202-T15
Dear Sir,
Thank you for the above mentioned enquiry.
We are pleased to submit our offer as per our specification as follows:
We hope you will find our offer acceptable and if you need any clarifications, please do not
hesitate to contact the undersigned.
Osama El-Hakim
Commercial Manager
Mobile: 050 483 0071
E-mail: osamaelhakim@rezayat.com.sa
Sir,
We are pleased to submit our offer for the supply of Gate Valve against your above referred RFQ; below is the
table of information:
2. The Unit Price quoted is based Sea Freight on DDP till AL KHOBAR Site Basis. The above price
includes freight charges, customs duty, customs clearance, documentation and local delivery charges.
4. The offer is valid for 30 days from the date of offer and subject to confirmation thereafter.
5. Delivery Period shall be 14 Working weeks Sea freight from the receipt of order & advance payment.
6. Payment terms shall be 50% advance along P.O and balance 50% by the way of TT against Proforma
Invoice prior to dispatch.
8. Modification/Cancellation of order is generally not accepted. Customer may terminate this order in
whole or in part in agreement with our principal and upon payment of reasonable cancellation charges
based upon all expenses incurred including labor, material cost, overhead costs and including a
reasonable profit thereon.
We trust this offer is to your satisfaction and look forward to receive your valued Purchase order.
Should you have any further clarification, please contact the undersigned.
Bhupendra
Sales Engineer
Piping & Static Division,
Gas Arabian Services Co Ltd,
0556251933.
An ISO 9001:2008 Certified Company
CEA/MKT/Q-12-13/2653
Monday, March 25, 2013
Dear Sir/Madam,
Please find herewith our quotation against your above referred inquiry.
Plot No. 177/179 Shiv Shakti Estate, Near V-Trans, Narol Road. Ahmedabad – 382405 Gujarat, India.
PHONE / FAX: 079 –25730189, EMAIL: cairvalve@gmail.com Website: www.cairindia.in
An ISO 9001:2008 Certified Company
QTY IN NOS. 02 02 02 01 01 01
Plot No. 177/179 Shiv Shakti Estate, Near V-Trans, Narol Road. Ahmedabad – 382405 Gujarat, India.
PHONE / FAX: 079 –25730189, EMAIL: cairvalve@gmail.com Website: www.cairindia.in
An ISO 9001:2008 Certified Company
Yours faithfully,
For, CAIR EUROMATIC AUTOMATION PVT. LTD.
Zaheen Valiulla
Business Development
Cell: +91 98792 08634
Plot No. 177/179 Shiv Shakti Estate, Near V-Trans, Narol Road. Ahmedabad – 382405 Gujarat, India.
PHONE / FAX: 079 –25730189, EMAIL: cairvalve@gmail.com Website: www.cairindia.in
Formerly known as: Mushabab Mufleh Cont. Est.
14 January 2013 Ref.: 242‐01‐PT13
M/s. Radicon Gulf Consult & Kentz Engineering
Al Khobar ‐ Kingdom Of Saudi Arabia
Tele: (03) 857 4505 Ext. 5218
Fax : (03) 857 6662
Attention : ENG. JOHN COADY
ENGINEERING MANAGER
Dear Sir,
Subject : QUOTATION FOR PRE CONSTRUCTION TERMITE CONTROL SERVICE
Project : RC PROJECT – CONTRACT NO. 027‐T15 LOCATED AT JUBAIL
We are glad to present our quotation for Pre construction Termite
Treatment Service for the above mentioned project to your kind consideration.
We are proud to introduce ourselves as one of the leading Pest &
Termite control establishments in the Kingdom. We have major projects in hand
like Saudi Consolidated Electric Co. (SCECO), Saudi Arabian Oil Company
(ARAMCO) ‐ Contractor registration No. 10006385, Aramco Supplier Vendor Code
Commission for Jubail & Yanbu ‐ Pest Control Service Contractor # 385 – S08, Al
Jubail Fertilizers (SAMAD) Contract # 4500020358, Saudi Arabian Petrochemical
Co. (PETROKEMYA) Contract # AG 99‐315, Saudi Aramco Shell Refinery Co.
(Saseref), Ar‐Razi Housing project located at Jubail, HalfMoon Housing project
located at HalfMoon Bay, Sunset Beach Project located at Aziziya, PCF Training
facility project located at Ras Al Ghar, Giant Store located Jubail, Giant Store
located Dammam (Contractor: M/s. Al Muhaidib Cont.), A.A. Turki Corporation
(ATCO), Saudi Arabian Saipem Saudi Techint JV Dhahran, Prince Sultan Palace at
Rakha and Aziziya, Saudi Aramco Built Government Schools (Northern & Central
Areas), and many others.
We use the latest, safest & most effective Pesticide and Termiticide
chemicals, approved and recommended by WHO (World Health Organization) and
EPA (Environment Protection Agency). The chemicals used by "HIT" are safe to
residents, pets and environment and are in accordance to the Saudi Pesticide
regulations & Manufacturer's recommended application instructions. "HIT" is a
member of the NPCA (National Pest Control Association) USA.
PREMISES : Royal Commission Project (Contract No. 027‐T15) located at Jubail,
having approximately 195,571 Sq. Mtrs.
APPROVED TERMITICIDE : Biflex (Details enclosed).
CONTRACTUAL VALUE: Our charges for pre construction termite control service
for the above mentioned project will be SR. 3.85 (Saudi Riyal Three and Halala
Eighty Five Only) per Sq. Mtr./ L. Mtr.
VALIDITY FOR THE OFFER: Validity for this offer is 60 (sixty) days from quotation
date.
WARRANTY : Upon the completion of the works TEN (10) years warranty will be
issued in favour of the assigned client. The warranty effective date will be the
treatment completion date of each unit/building of the project.
NOTE:
1‐ The client should inform us regarding the initial work 3 days in advance.
2‐ Each further service should be notified at least 24 hours in advance.
3‐ Water for termiticide chemical dilution shall be arranged by the clients at
site.
4‐ The site should be vacated by the other workers for termite control service
at least 30 minutes before starting the treatment.
5‐ Client should arrange minimum 200 sq. mtrs. for each service request. If it
is less than 200 Sq. Mtrs, then we will charge SR. 100/‐ as transportation
charge per visit.
Further more, For any detailed information on above mentioned subject please
call us at your convenience.
We wish this offer could meet your kind approval and assuring you of our best
professional service at all times.
Thanking you.
Sincerely yours,
AHMED M. HUSAIN
(Operations Manager)
Q UOTATION
DATE :18 FEB. 2013
REF. : FMC-QUT-ANT-014
Dear Sir,
In reference to your faxed dated on 18th of February 2013, we would
like to thank you for inviting us to offer our best quotation regarding
for the above service in your new project at Royal Commission Jubail.
LOCATION
In Jubail City at Royal Commission, M/s. Radicon Gulf Consult &
Kent Eng’g. having new project ten (10) academic buildings at Royal
Commission under construction total area 195,000 square meters.
SCOPE OF WORK
The Anti-proofing pre-construction termite control service will be
operated in three (3) stages only;
1. Below footing (before concrete)
2. Grade on beam (foundation after back filling)
3. Walk way / pass way (surrounding of the building)
OUR CHEMICAL FOR TERMITE CONTROL
BIFLEX TC is termicidal concentrate formulation containing the active
ingredient 25.1% Bifenthrin. Biflex TC is used as a public health
pesticide for the control of termite’s pre and post construction. FMC
and Biflex are Registered Trademarks of FMC Corporation,
Philadelphia, USA and the producer in the kingdom is Astra Industrial
Complex Co. Ltd. (ASTRACHEM), which formulated specially for the
termite situation here in the Kingdom of Saudi Arabia.
• 25.1 % Bifenthrin is the active ingredient in the Biflex emulsion and is
present and between 0.5 g/L and 1.5 g/L.
• Application of this chemical should be carried out by professional pest
control operators only.
CHEMICAL DOSAGE
Biflex TC shall be applied at 0.06% concentration (2.65 ml of Biflex TC in 1 liter of
water).
The emulsion should be applied at horizontal barriers
- Spray area intented to be covered with concrete.
BIFLEX TC
National Rifle Association Approval no. 54547/0801
SASO Registered no. 179-29-772
PRODUCT BY: FMC Corporation, Agricultural Product Group 22-05-00-00
PRODUCED BY: Astra Industrial Complex Co. Ltd. (ASTRACHEM) Saudi Arabia
WARRANTY
Providing the pre-construction termite control service as per the job specification
will cover a Ten (10) Years Warranty, after all the invoices are paid in full.
• The warranty covered only the areas treated and will provide special
service after assessment of the complaint.
• After the treatment, any modification/changes such as additional land fill or
excavation in the area must be treated again. Failure to inform us will
nullify/cancel the warranty.
OUR CHARGES
The above said scope of works our unit charge, SR. 2.20 per sq. meter
(Two and Twenty Halalas Saudi Riyals Only) per square meter
TERMS OF PAYMENT
Payment in pro-rata basis and upon presentation of treatment, receipt will be
given to the area and payable in full payment against the invoice submission.
______________ ______________
PAUL T. RAJ SANTOS S. DE LEON
Operation Manager Operation Supv.
Mobile no. 0505858329 Mobile no. 0503180714
Page 1 / 1
U 5 G Middle East Ltd.
7410 AI Kharj Road 2nd Industrial City, DAMMAM- 34326- 4201, Saudi Arabia
QUOTATION
Subject: I REVISED QUOTATION' REF. NO. USGME-0736-10R1 DATED MARCH 19, 2011.'
I 2 I S02MT3600 I Wall Angle 3.60M long --l lM, 16416.0~ 0.00, 1.520~
i
24,952.32
E ~+
---
6IRH500-- R 00 HANGER 500mm BNDl 102.0~ ---- 0.00, -. 60.0000 6,120.00
I
I
7 i
I
RHCLIP I ,
A djustable Hanger Butterfly Clips I "00.0 I 0.."J 0.'"" z.sso oo
911pA2s2s---T
Furring Channel 22x69x22mm - Thickness = 0.5mm x 3lM IlM -19446.0~ 0.Oolf-- __ 2.353~i-. ___ 4~~
L. S FC2269 i.
1 Perimeter Angle 25x25 l-Profile - Thickness = 0.5mm x 3lM lM 4065.001 0.00 1.098~ 4,464.18
[~~~-- II W~I~
\IIIall
Track 30x75x30mm - Thickness = 0.5mm x 3lM lM i 60243.00 0.00, 2.900~ 174,704.701
l_12 I ST3575 , W all Stud 34x73.8x36mm - Thickness = 0.5mm x 3lM lM 183462.00' ~ __ 3_.3()O 605,424.6~1
-_~~~~~-_====~~~~~~~~~-:::::::~==~~~~~~~~~~-~~.-_-_-_~~~~
~~~ Freight Charges :'
-----
0.0
Only Two Million Nine Hundred Sixty Two Thousand Ninty Five Riyals GRAND TOTAL: 2,962,095.00
I --------f -!
f1~~1'
1,,·;\1
Pierre Arsane ELiE MAJDALANI / Walid Abou Dhargam
!
OFFER SHEET
Dear Sir,
We are pleased to submit an updated offer for our PEC Duct (Poly Ethylene Corrugated
Duct), in line with your requirement for the upcoming new installation project works STC /RC
Jubail Infrastructure - Marduma (Jubail) Area - 725-C03 (Site Development at Marduma),
570-Y02 (Potable Water Pumpuming Stn). Details below are wished to be of your
satisfaction.
Price
Disc. Total
Model Item & Description Valid for
U/ Price Qty Amount
PEC Duct - Main Offer
(a) Polyethylene Corrugated Optic
Duct (COD)
PEC HDPE Material; Outer duct OD 110
5B mm ± 2 mm; built-in 5 sub-ducts, of 9,500
OD 33 mm and ID 28 mm; wall SR 23.00 meter SR 218,500.00
thickness 2.5 ± 0.5 mm, (5B)
MIC # 412xxx. All orange color, one
sub duct black
Incl. 19 x R-500
Accessories
Joint Closure / Coupling Kit
(b) for PEC Duct Model 5S (5B)
JCC- including 5 x sub duct coupling [MIC SR420.00 25 Ea SR 10,500.00
5B # 412xxxx] and 1 x Closure [MIC #
412xxxx]
(c) Man hole / Hand hole Connector
MHC for PEC Duct Model 5B or 3D SR 35.00 50 Ea SR 1,750.00
MIC # 412xxxx
(d) End Cap
ECAP for PEC Duct 5B/ 3D/ EMP110 SR 22.00 25 Ea SR 550.00
MIC # 412xxxx__
(e) PEC Duct – Tool Kit
TKIT- for PEC Duct Model 5B or 3D SR
1 Ea SR 7,000.00
5B or 3D including 1 x sheath stripping tool, 1 7,000.00
x jointing tool and 1 x misc items set
SUB-TOTAL (materials) SR 238,300.00
Reel (R-300: 0 x 600SR ea + R-500: 19 x 750SR ea) Caution Deposit 0.00
R- Stand (1 x 750SR ea) Caution Deposit 750.00
Grand – TOTAL SR 239,050.00
(2) Payment:
30% down payment, 70% by Irrevocable L/C on delivery in our favor OR by cash
prior to delivery. If PO Value is less than
SR 100,000 then 100% along with PO
Payment to our Saudi British Bank A/c # 001-009737-002 [IBAN SA 31
4500 0000 0010 0973 7002 ], Dabbab Street Branch, PO Box 9084,
Riyadh 11413, Tel. +966-1-276 3764, Fax. +966-1-276 3812
Best regards,
Rajan V. Jose
Projects Manager (M. 0507871062)
First Telecom Industries
Ph. +966-1-281 2777 x 241
Fax. +966-1-281 2727
Email: rjose@ftc.com.sa
JS-PLATFORM Junos Space Network Management Platform with 4 Cores $500.00 1 60.00% $200.00
JS-NETDIR-100 Junos Space Network Director for 100 devices. $7,000.00 5 60.00% $14,000.00
QUOTATION
M/S MOHD FAHTI AL SHAHRI EST
P.O. BOX 1094 ALKHOBAR 31952
KINGDOM OF SAUDI ARABIA
TEL : (+966) 8645471/8951652 FAX : (+966) 8645002
ATTN : MOH'D FATHI AL SHAHRI
SR.
NO. ITEM MODEL DESCRIPTION DIMENSION (MM) QTY U/PRICE
1 A PROFESSORS OFFICE
AS 5 SWIVER CHAIR STANDARD 1 500.00
AS 2 CHAIR STANDARD 1 650.00
DFLDB1651507545 L-SHAPE DESK 1650MM X 1500MM X 750MM X 450MM 1 680.00
VA II 003 2-SEATER COUCH 1 980.00
SFWCB604575 LOW TABLE (SWING DOOR) 600MM X 450MM X 750MM HIGH 1 200.00
SFWB9045180 CABINET (SWING DOOR) 900MM X 450MM X 1800MM HIGH 1 600.00
2 B LECTURERS OFFICE
AS 5 SWIVER CHAIR STANDARD 1 500.00
AS 2 CHAIR STANDARD 1 650.00
DFLDB1651507545 L-SHAPE DESK 1650MM X 1500MM X 750MM X 450MM 1 680.00
SFWB9045180 CABINET (SWING DOOR) 900MM X 450MM X 1800MM HIGH 1 600.00
4 D TRADITIONALCLASSROOM
WRITERS DESK 1600MM X 600MM X 750MM HIGH 1 600.00
DFDDB1808075 LECTURERS DESK 1800MM X 800MM X 750MM HIGH 1 530.00
FL 5 CLASSROOM CHAIR STANDARD 1 250.00
FL 1 LECTURERS CHAIR STANDARD 1 300.00
5 E INTERACTIVE CLASSROOM
2 PERSON DESK 1400MM X 450MM X 750MM 1 620.00
3 PERSON DESK 2100MM X 450MM X 750MM 1 730.00
DFDDB1808075 LECTURERS DESK 1800MM X 800MM X 750MM HIGH 1 600.00
FL 5 CLASSROOM CHAIR STANDARD 1 250.00
FL 1 LECTURER CHAIR STANDARD 1 300.00
7 G STUDIO
DFDDB1058075 COMPUTER DESK 1050MM X 800MM X 750MM HIGH 1 300.00
DFDDB1658075 DEMO DESK 1650MM X 800MM X 750MM HIGH 1 450.00
FL 5 OPERATOR CHAIR STANDARD 1 300.00
EQUIPMENT CUPBOARD 450MM X 900MM 1
EQUIPMENT CUPBOARD 1650MM X 780MM 1
8 H COMPUTER LAB - COMPUTER ENGINEERING
DFDDB1306075 COMPUTER DESK 1300MM X 600MM X 750MM HIGH 1 390.00
DFDDB1106075 COMPUTER DESK 1100MM X 600MM X 750MM HIGH 1 350.00
DFDDB1806075 LECTURERS DESK 1800MM X 600MM X 750MM HIGH 1 450.00
FL 5 CLASSROOM CHAIR STANDARD 1 300.00
FL 1 LECTURERS CHAIR STANDARD 1 450.00
10 K SEMINAR ROOM
TABLE 1400MM X600MM X 750MM HIGH 1 630.00
TABLE 700MM X 600MM X 750MM HIGH 1 580.00
FL 5 CHAIR STANDARD 1 300.00
13 N MULTIMEDIA LAB
DFDDB1108075 COMPUTER DESK 1100MM X 800MM X 750MM HIGH 1 400.00
FL 5 COMPUTER CHAIR STANDARD 1 300.00
FL 1 CHAIR STANDARD 1 450.00
CFRDB10010075 TABLE (CIRCULAR) 1000MM DIAMETER X 750MM HIGH 1 650.00
14 P TEACHING LAB
DFDDB1908075 COMPUTER DESK 1900MM X 800MM 1 640.00
DFDDB1108075 COMPUTER DESK 1100MM X 800MM 1 450.00
DFDDB1808075
18080 LECTURERS
C S DESK
S 1800
1800MM X 800MM
800 1 680 00
680.00
FL 5 CLASSROOM CHAIR STANDARD 1 300.00
FL 1 LECTURERS CHAIR STANDARD 1 520.00
15 Q LANGUAGE LAB
DFDDB1308075 COMPUTER DESK 1300MM X 800MM 1 450.00
DFDDB2006075 COMPUTER DESK 2000MM X 600MM 1 670.00
DFDDB1106075 COMPUTER DESK 1100MM X 600MM 1 400.00
DFDDB1808075 LECTURERS DESK 1800MM X 800MM 1 430.00
FL 5 CLASSROOM CHAIR STANDARD 1 300.00
FL 1 LECTURERS CHAIR STANDARD 1 550.00
16 R LANGUAGE LAB
CFRDB808075 TABLE (CIRCULAR) 800MM DIAMETER X 750MM HIGH 1 350.00
DFDDB707075 TABLE 700MM X 700MM X 750MM HIGH 1 400.00
CHAIR (STACKABLE) STANDARD 1 300.00
OPTIONAL TROLEY
FL 5 TROLEY (MAXIMUM 20 UNITS PER TROLEY) 1 350.00
……………………………………
From: Eduardo T. Labrador Jr. [mailto:eduard@fbcc-ltd.com]
Sent: Monday, March 04, 2013 4:14 PM
To: rgckderek@sps.net.sa
Cc: Ismet Amin Khawja
Subject: Requesting updated Quotation Ref No. FBCC/485/1669/R1/2010
Best Regards,
--
EDUARDO T. LABRADOR JR.
Foundations Building Contracting Co. Ltd.
E-Mail: eduard@fbcc-ltd.com
Website: www.fbcc-ltd.com
Tel.: 03-864-6593
Fax: 03-894-5869
P.O. Box 31269
Al-Khobar 31952
K.S.A.
19 February, 2013
In response to your request for budget pricing, Arabian CBI (CB&I) is pleased to provide
budgetary estimate information for the design, supply, supervision, fabrication and erection
of 4 units of Steel Water Storage Tanks as summarized in Part 1. The budget information is
based on the information received by facsimile on August 4, 2012 and February 17, 2013
with reference number as stated above.
In compliance with your request, CB&I has also submitted herewith product standard/
brochures
Should RGCK have any questions or comments regarding this proposal, please do not
hesitate to contact the undersigned.
CB&I looks forward to the opportunity of working with your company towards the successful
execution of this work.
Yours sincerely,
On behalf of Arabian CBI Ltd. (CB&I)
J.D. Shipley
Business Development Manager
RADICON – GULF CONSULT &
KENTZ ENGINEERING Arabian CBI Ltd
RGCK Al Khobar, Saudi Arabia
PART – 1
SCOPE OF WORK
A summary description of the steel tanks considered for this proposal is as follows:
Dia Height
Sr.# Tank # Item Name Qty. Roof Type Code
(M) (M)
Rafters
API 650 11th
PW-T- Potable Water supported Fixed
1 2 80.00 8.285 Edition,
100/200 Storage Tank Cone Roof with
Addendum 1
Interior Columns
Rafters
Irrigation API 650 11th
supported Fixed
2 IW-T Water Storage 2 66.00 9.100 Edition,
Cone Roof with
Tank Addendum 1
Interior Columns
CB&I Proposal
Scope of Work Description
CB&I Proposal
Scope of Work Description
CB&I Proposal
Scope of Work Description
CB&I Proposal
Scope of Work Description
PART – 2
BUDGET INFORMATION & COMMERCIAL TERMS
Please note that as this is an indicative budget information submission, pricing has been
developed based on standard CB&I estimating norms for Middle East which include Saudi
Arabia. In absence of site inspection report, CB&I assumes jobsite is clear from any
obstruction and with open free access to manpower and equipment.
Budget information pricing assumes both tanks will be ordered. Individual tank prices are not
available for individual acceptance
CB&I’s budget assumes mutually agreeable terms and conditions including neutral cash flow
for payment by RGCK
This document is the property of, and contains data proprietary to Chicago Bridge and Iron
Company (CB&I). It may be utilized only by employees of the Company to which it is being
furnished.
Neither the budget nor any part thereof may be duplicated nor disclosed to others without
the prior written consent of CB&I, and this document and all portions thereof, including any
copies shall, at the request of and in accordance with instructions of CB&I, be promptly
returned or destroyed.
VALIDITY
CB&I’s budget submission is based upon current day pricing and therefore has no validity
and is not open for acceptance as an order.
Search
+jahangeer Search Images Maps Play YouTube News Gmail Drive Calendar More
Click here to enable desktop notifications for Gmail. Learn more Hide
Gmail More
COMPOSE Binary Options Trading - www.Opteck.com/Saudi+Arabia - Opteck™ Teaches How To trade Binary Options. Get A Free E-book Now !
Inbox (10)
Important
12-T3-017 - JUBAIL – POTABLE & IRRIGATION WATER STORAGE TANKS : BUDGETARY QUOTATION
Inbox x
Sent Mail
Drafts (98)
t3services 12:09 PM (21 hours ago)
All Mail
to me, DEREK, Georges, Vicken, Melkon
Spam (167)
BUSINESS REF: 12-T3-017/PRP/OE-002
HEALTH
INSURENCE Dear Sirs,
JOBS Re your below e-mail please note that we reconfirm our prices of our Offer above.
Quotation Kindly do not hesitate to call us for any further information.
More
Sincerely Yours
Vicken Tcheroyan
https://mail.google.com/mail/u/0/?shva=1#inbox/13d15c0100e4c96f 1/1
Quotation.: PQ-HE-120335-MA
Date : 8/27/2012
Client: Radicon Gulf Consultancy and Kentz Engineers Association.
Project: NOVEC-1230 fire Suppression System
Attn: Mr. Derek Daly
Total SR 4,447,698.50
Discount SR 0.00
G.Total SR 4,447,698.50
1. Heba’s offer is for Design and Supply of NOVEC-1230 fire suppression system & and its related
Detection System equipments.
2. Installation, Programming, testing & commissioning of NOVEC-1230 fire suppression system is out of
our scope of work, in case of any change our offer shall vary accordingly.
3. Heba's offer is based on the NOVEC-1230 Gas quantity calculated based on the volume provided in
your RFQ. In case of any change in the gas quantity during design stage, change in the
room/hazard dimensions or due to comments from the consultant/or client, the offer shall vary
accordingly or shall have commercial impact.
4. Heba’s offer includes the addressable type fire alarm detection system; in case of any change our
offer shall vary accordingly.
5. We have proposed separate addressable fire alarm control panel for separate room, in case of any
change our offer shall vary accordingly.
6. Networking/interfacing among fire alarm control panels is out of our scope of work, in case of any
change our offer shall vary accordingly.
7. Any kind of third party utility interfacing and networking with the fire alarm system is out of our
scope of work. In case of any changes our offer shall vary.
8. Programming, Testing & Commissioning if required shall be charged on per day basis SR-2500/-
9. Actual Discharge test of NOVEC-1230 system is out of our scope of work. We shall carry out only
functional test.
10. Room integrity test is out of scope of work. In case of any change our offer shall vary.
11. Client has to ensure the hazard area is completely enclosed for each room above ceiling void &
subfloor void and is leak proof. Any closing of openings of the room is not in our scope of work.
12. Power Supply of 110/220VAC at 50/60Hz have to be provided by the client for the fire alarm control
panel. This Power supply must be a stable power supply with the maximum of +_ 10% variations,
and in case of power supply fluctuations a stabilizer shall be provided by the client.
13. ID/Gate pass & work permit receiver shall be arrange/provided from your end while Programming,
Testing & Commissioning of the project.
14. Material inspection at vendor/manufacturer facility is not considered in our offer, hence shall not be
in our scopes of work.
15. HEBA reserves the right to change the prices of any item, if in case the client has missed out to
provide any vital information for our estimation. In case of any change in the specification or
quantity, the prices will vary accordingly. HEBA has the right to accept / decline any purchase order
which has discrepancy with respect to the quotation or its latest revision.
DEVIATION /CLARIFICATIONS:
16. Heba's offer includes 4.5% for some rooms & 4.2% design concentration for some rooms as per the
design requirement of NFPA for NOVEC-1230 Gas as mentioned in the RFQ provided. In case there
is a comment from client during detail engineering in the Gas quantity or design concentration, our
offer shall vary accordingly.
17. It shall be noted that the offer is subject to variance at a later date, as the present proposal is
provided on limited information available in the RFQ. This is subject to change after a detailed site
survey which will be required to be conducted when a more precise proposal is required to be
submitted.
18. Provision for supply of fire/smoke dampers, interface with HVAC, BMS or any other third party
system is not included in this offer due to insufficient information. If required shall be charged extra.
19. Any tools and equipments required at site to lift the equipment/material at higher elevation like
forklift, carne, man-lift, etc shall be provided from your end.
20. FAT (Factory acceptance test) has not been included in our offer, if require shall be charged extra.
21. Client/Consultant shall provide all the work permits, ID and required permissions for programming,
testing & commissioning.
22. The offer doesn’t include the spare parts require for operation and maintenance, if require shall be
charged extra.
23. Electricity required during programming, testing & commissioning of the project shall be provided by
the Client/Consultant.
24. Any purchase order resulting from this offer with delay penalty clause shall not be acceptable.
25. We have considered the altitude correction factor as 1 at sea level, any change in altitude factor
shall vary the offer accordingly.
Material Delivery:
14-16 from the date of receipt of your commercially and technically cleared purchase order, receipt of
down-payment, approval of products and approval design drawings.
COMMERCIAL TERMS:
PAYMENT TERMS:
ORDER ACKNOWLEDGEMENT:
QUOTATION
WITH REFERENCE TO YOUR ABOVE ENQUIRY, WE ARE PLEASED TO QUOTE AS FOLLOWS :
PUMP MATERIALS
CASING : CAST IRON ASTM A48
CASING WEARING : ST. STEEL 416
SHAFT : ST. STEEL 416
IMPELLER : ST. STEEL 316
SHAFT SLEEVE : ST. STEEL 316
SEAL : MECHANICAL SEAL
DOCUMENTS : INCLUDED
NON WITNESS
- PERFORMANCE TEST CERTIFICATE
- HYDROSTATIC TEST CERTIFICATE
- MATERIAL TEST CERTIFICATE FOR CASING, SHAFT & IMPELLER
-------------------
TOTAL PRICE : SR 1,691,000.00
=========
(SAUDI RIYAL ONE MILLION - SIX HUNDRED NINTY ONE THOUSAND ONLY)
THANKING YOU
For SAUDI PUMP FACTORY
Kingdom of Saudi Arabia Riyadh 11553 الرياضP.O Box 51737 ب. صI.L. 1205 ; ترخيص صناعيC.R. 1010021424 ت. س: المملكة العربية السعودية
TEL.: KHOBAR 03/ 8943793 : الخبر Jubail 03/3476772 : الجبيل Jeddah 02/6691839 :جدة Riyadh 01/2652123: ھاتف ; الرياض
FAX.: KHOBAR 03/ 8986554 : الخبر Jubail 03/3460101 : الجبيل Jeddah 02/6607243 :جدة Riyadh 01/2651071: فاكس ; الرياض
ALKHORAYEF COMMERCIAL CO. شــــركة الخــــــريف التجــــارية
P.O. Box 281808, Riyadh 11392 ١١٢٩٣ الرياض٨٢١٢٨٢ ب.ص
Kingdom of Saudi Arabia المملكة العربية السعودية
Tel.: 4955452 – Fax: 2134716 ٨١٧٤٣١٢ : فاكس٤٥٩٩٤٩٨ :تليفون
___________________________________________________________________________________
Dear Sir
Reference to your inquiry , we have the pleasure to submit you the following offer for supply of the
Centex- Cornell Pump equipment on the terms stated in the attached specification, which form an integral
part of this offer.
1- (908.2 M3/hr@ 60 M) :
1
ALKHORAYEF COMMERCIAL CO. شــــركة الخــــــريف التجــــارية
P.O. Box 281808, Riyadh 11392 ١١٢٩٣ الرياض٨٢١٢٨٢ ب.ص
Kingdom of Saudi Arabia المملكة العربية السعودية
Tel.: 4955452 – Fax: 2134716 ٨١٧٤٣١٢ : فاكس٤٥٩٩٤٩٨ :تليفون
___________________________________________________________________________________
For further technical information please refer to the attached technical details.
We hope that our offer is acceptable for you and if there’s any other clarifications please contact with the
under sign.
Best Regards;
2
ALKHORAYEF COMMERCIAL CO. شــــركة الخــــــريف التجــــارية
P.O. Box 281808, Riyadh 11392 ١١٢٩٣ الرياض٨٢١٢٨٢ ب.ص
Kingdom of Saudi Arabia المملكة العربية السعودية
Tel.: 4955452 – Fax: 2134716 ٨١٧٤٣١٢ : فاكس٤٥٩٩٤٩٨ :تليفون
___________________________________________________________________________________
QUOTATION
Date 4 February 2013 Our ref. CO/DM/MK/223/108/012/Rev-1
No. Of Pages 3 Your Ref.
To RGCK From Eng. Mohamed Aldeeb
Att. John Coady Division Centex Arabia
Tell. +966 03-899-9573 Ext-521 Tel. no. +966 03 8571534 EXT. 14
Fax +966 03-895-3609 Mobile No. +966 03 8571534 EXT. 14
Mobile No. Fax no. +966 03 8142449
Email rgckderek@sps.net.sa. Email mkhlifa@alkhorayef.com
Dear Sir
1
ALKHORAYEF COMMERCIAL CO. شــــركة الخــــــريف التجــــارية
P.O. Box 281808, Riyadh 11392 ١١٢٩٣ الرياض٨٢١٢٨٢ ب.ص
Kingdom of Saudi Arabia المملكة العربية السعودية
Tel.: 4955452 – Fax: 2134716 ٨١٧٤٣١٢ : فاكس٤٥٩٩٤٩٨ :تليفون
___________________________________________________________________________________
2
ALKHORAYEF COMMERCIAL CO. شــــركة الخــــــريف التجــــارية
P.O. Box 281808, Riyadh 11392 ١١٢٩٣ الرياض٨٢١٢٨٢ ب.ص
Kingdom of Saudi Arabia المملكة العربية السعودية
Tel.: 4955452 – Fax: 2134716 ٨١٧٤٣١٢ : فاكس٤٥٩٩٤٩٨ :تليفون
___________________________________________________________________________________
Prices
For further technical details please refer to the attached pump catalogs and pump curve.
We hope that our offer is acceptable for you and if there’s any other clarifications please contact with
the under sign.
Best Regards;
3
-----Original Message-----
From: Mohammed Qunaibi [mailto:qunaibi@saudidiesel.com.sa]
Sent: Tuesday, March 26, 2013 11:35 AM
To: rgckderek@sps.net.sa
Cc: Hussain Al-Marhoon
Subject: Validation of Price
Further to our phone call and the attached quotation ref SD12-395R1 ,
the prices are subject to a 5% price increase .
The validity would be till end of June 2013.
Best Regards
Mohammed Qunaibi
Director Power Equipment Sales
Saudi Diesel Equipment Co Ltd.
Please always indicate in the case of payments and further enquiries:
Dear Sir,
We thank you for your interest in our product and have pleasure in offering you the following material on the basis
of our General Terms of Delivery:
We trust that our quotation meets your requirements and in the case of an order assure you that all work will be
carried out in a professional manner. Should you require any further information, we would be pleased to assist.
Yours sincerely
This is system generated quotation and does not required any signature
Registered Office: Al-Khobar, KSA The Saudi British Bank (SABB), Riyadh, KSA Branch of Demag Cranes & Components (Middle East) FZE
CR No. 2051043427 IBAN: SA9645000000003229598001 (SAR) PO Box No 31235, Al-Khobar 31952, KSA
IBAN: SA9745000000003229598080 (USD) Tel: +966 (3) 8810 657
Swift: SABBSARI Fax:+966 (3) 8817 652
Page 1 of 5
Quotation No.: 9.510. 3623_00 from 12.3.2013 Page: 2 of 5
Technical description
Item 1
The steel construction of the crane is calculated in accordance with DIN 15018, hoisting classification H2, stress
group B3.
Crane girder is a fabricated box with scarfed ends at an angle of 45°. The level at the underside of the crane
girder coincides with the level of the running surface of the crane track. The crane is designed for indoor operation
with normal ambient conditions and temperatures of -10°C up to a maximum of +45°C.
Crane includes an electric low headroom, monorail crab travelling on bottom flange of the crane girder.
Monorail crab:
Type EK DR-Pro 3-2 4/1-6,0 Z-6/1
Drive classification FEM: 4m / ISO: M7
Life span of gearbox 20% above the FEM (ISO) value
Load hook size 1,6 to DIN 15400
Hookpath up to 6,0 m
Speeds (approx.):
Main Hoisting Speed 7,2 m/min 4,10 kW 40 % CDF
Creep Hoisting Speed 1,2 m/min 0,66 kW 20 % CDF
Cross travel speed 7,2/28,8 m/min 0,11/0,41 kW 40/40 % CDF
Long travel 12,0/48,0 m/min 2x0,11/0,41 kW 40/40% CDF
Control:
Demag Line Control (DLC) with DST, festoon system with independent mobile pendant across the crane span.
Conductor system:
Crab supply by flat cable festoon system.
Crane electrics:
The crane electrical equipment is based on a conventional contactor control. This offers a high level of operating
safety and meets the requirements of the corresponding regulations. All plug connections of the flexible cabling and
wiring are firmly attached. All drives are disconnected together by means of a crane isolating switch.
Cross travel limit switch Two-stage limit to prevent crab colliding with the end stops
Thermal motor protection Protection against over temperature by means of integrated micro-switch
Long travel limit switch Two stage cut-off to avoid fast and slow speed collision with the crane with
end- stops
Quotation No.: 9.510. 3623_00 from 12.3.2013 Page: 3 of 5
Finish Colour:
Structural steelwork:
- Steel structure prepared in accordance with DIN EN ISO 12944
- One prime coat, zinc phosphate epoxy paint, total paint thickness approx. 50 µm
- One intermediate coat, total paint thickness approx. 100 µm
- One finish coat, RAL 1004, golden yellow, total paint thickness approx. 50 µm
Crab/carriage:
- Two-tone powder coating in azure blue RAL 5009 and silver grey RAL 7001, paint thickness 80 µm
Drives:
- In azure blue RAL 5009
End carriage:
- In RAL 1004
Documentation:
- EU document according to the Machinery Directive
Item 1.1
Item 1.2
Item 1.3
1.2 1 Flat rails for 23.4 m Bay (Supply Only) 3,400.00 3,400.00
1.3 1 Erection & Commissioning of the Crane, DCL and Flat Rails 10,500.00 10,500.00
*** In the event of changes by the customer, the customer shall be liable to additional costs “if any”.
Terms of Sale:
Please read these terms and conditions carefully before accepting this quotation. By issuing a Purchase Order
you acknowledge that you have read and agreed to these Terms and Conditions
Price Validity: This quotation is valid for 60 days from the quotation date. A revised quotation will be
issued after this date upon request which, may result in a price adjustment.
Price Basis: CIP Dammam, KSA (incoterms2000) including (5%) customs duty applicable at the time
of delivery.
Duty exemption: For companies or organizations, who exercise the facility of obtaining duty exemption on
their imports, the responsibility of the documentation process towards getting the
approvals from competent authorities lies with the buyer themselves, including any
incidental charges or fees such as document legalization or attestation.
Payment Terms: 30 % deposit with Purchase Order, to be transferred to our bank account within 7 working
days upon receipt of our invoice. Details as below:
Time for Delivery: 16 – 18 Weeks from the date of acceptance of the specifications as per the quotation
(duly dated, signed & stamped) and receipt of the deposit
Contract: This offer is subject to our Standard Conditions of Sale, issue June 2009. A copy is
available upon request.
Warranty: Warranty is in accordance with Section 8 of our Conditions of Sale. The warranty period is
12 months after the date of commissioning or a maximum of 18 months after product
inspection & acceptance by the customer
When sizing the incoming cable, the maximum possible starting current must be
considered, the voltage drop at the terminals must not exceed 5%.
Quality Control: All Demag Cranes & Components are produced in accordance with ISO 9000.
Service Contacts: Our after sales service toll free number is 800 4784 (UAE), 800 118005(KSA).
Dear Jahangeer,
Item # 1
• Supply of 2T Wire Rope Monorail Hoist for Indoor application and standard atmospheric
conditions + 8.3m power supply line + electrical trolley + all other related accessories.
• Delivery to Jubail.
Item # 2
• Supply of 4T EOT Crane, Single Girder with 9.2m span, designed for Indoor application and
standard atmospheric conditions + 30m power supply line + 60m rails + all other related
accessories.
• Delivery to Jubail.
I hope above information is useful for you. Please contact me if you have any clarification.
Best Regards
Ammar Jawad
Dear Gentlemen:
Thank you for your confidence in our company by sending us your inquiry for the above-subject.
We are pleased to submit herewith our offer for your requirement of one 3.2ton Electric Wire
Rope Hoist, duly annexed as follows:
Annexure – I : Technical Offer, with Electric Hoist Data Sheets & Drawing
Annexure – II : Price Schedule, Commercial Terms & General Notes
Annexure – III : General Commercial Terms & Conditions of Sale
SAUDICRANES is a well reputed and the largest crane & hoist manufacturer in the Arabian
Gulf Region today, catering to a wide range of industrial sectors. SAUDICRANES is a member
of the Konecranes Group of Companies with headquarters in Finland, who are the world’s
leader in crane & hoist industries.
SAUDICRANES receives complete engineering & service support from Konecranes along with
all mechanical and electrical components. All structures are manufactured in SAUDICRANES-
Jubail Industrial City plant, and the complete cranes & hoits are then assembled and tested at
its works prior to shipment, as required by client.
We hope you find our offer competitive and in line with your expectations. Should you need
more information or clarification, we would be glad to discuss with you any part of our technical
& commercial offers to ensure our mutual satisfaction.
As the leading crane & hoist company in the Region today, with the best experience in Royal
Commission and other special projects, we look forward to receiving your valued order, and
working with you towards the success of your projects.
Thank you and best regards,
SAUDICRANES & STEELWORKS FACTORY, LTD.
Elmer T. Fabros
Area Sales Manager
Mobile #050-394-2328
Page 1 of 4
ANNEXURE 1:
TECHNICAL SPECIFICATIONS
ELECTRIC MONORAIL HOIST
Operating Voltage : 380V, 3Ph, 60Hz (assumed power supply provided by client; to be confirmed
during design finalization)
Motors : Squirrel cage induction motor suitable for industrial / maintenance duty
application, suitable for the specified area
Brakes : Heavy-duty, fail-safe, electromagnetic disc brakes provided, integral with each
motor
Hook : Forged steel material; Single crook hook with safety latch
Page 2 of 4
Limit Switch : Provided for all hoist, and travel motions as per our standard; 2-step for all
horizontal travel motions
Excluded in : Monorail I-beams and their supports / base plates+anchor bolts, any accessory
Saudi Cranes’ Scope below hook, platforms & ladders; other related civil / structural works.
Main Isolator Switch & Rising Cable
1) After award of contract, before hoist manufacturing, General Arrangement Drawing in the required
format showing pertinent specifications and dimensions shall be prepared and submitted by us for
Client’s review and approval. This General Arrangement Drawing shall confirm the hoist capacity and
dimensions, after the heaviest load-weight and building structures’ dimensions are finalized.
2) The hoist shall be assembled at Saudi Cranes’ Jubail plant. Before dispatch, the hoist could be tested,
including 125% load tests, in the presence of client’s representatives, if Factory Acceptance Tests
(FAT) are required. The Hoist could be delivered in “ready-to-install” condition, wherever possible via
land transport. Hence, erection at site is not a complicated process. Thus, we are quoting only
Supervisory Services for site activities, if required.
Page 3 of 4
ANNEXURE 2:
PRICE SCHEDULE
Price, Saudi Riyals
Description Qty.
DDP/FOT Jubail Site
3.2ton x 3.8m. lift Electric Wire Rope Hoist with Motorized Trolley and
1
Festooned Cable Powerline System for 9.3meter straight monorail, as
Set
53,000
per enclosed technical specifications
Supervision of installation, testing & commissioning of our supplied Monorail Hoist @ SR 1,500
(estimated duration: 7days) (All jobsite laborers, equipment, facilities, and site test Per Man-day of
weights shall be provided by Client, free of charge to Saudi Cranes.) 8 hours each
1. Prices quoted are in Saudi Riyals, delivered duty-paid (DDP) to Mutrafiah-Jubail site on FOT (freight-on-
truck) basis, and are assumed to be ordered in one lot.
2. We guarantee our cranes & hoists for one year from date of commissioning or up to 18months from
delivery date.
Should you require Warranty Period extension, the additional costs shall be 5% of equipment price for
every year of extension.
3. Commissioning/start-up spares, and special tools are not required for our cranes.
Recommended Spare Parts could be quoted later, if required.
5. Delivery Time: Approx. 16-18 weeks from receipt of downpayment, and approval of General
Arrangement Drawings.
6. Validity of This Offer: Until one (1) month from now, subject to our written confirmation thereafter.
* * * * *
Page 4 of 4
Ref : 12 / 08 / 480A / EF / R0
Date : 15th September 2012
RADICON-GULF CONSULT & KENTZ ENGINEERING
Al - Khobar
Attn. : Mr. John Coady / Mr. Jahangeer Basha Shiek / Mr. Derek Daly
Engineering Manager Plumbing Design Engineer
Dear Gentlemen:
Thank you for your confidence in our company by sending us your inquiry for the above-subject.
We are pleased to submit herewith our offer for your requirement of two sets - Single-Girder
Electric Overhead Traveling Cranes & one set – Electric Monorail Hoist, duly annexed as
follows:
Annexure – I : Technical Offer, with Wheel Load Data Sheets & Drawings
Annexure – II : Price Schedule, Commercial Terms & General Notes
Annexure – III : General Commercial Terms & Conditions of Sale
SAUDICRANES is a well reputed and the largest crane & hoist manufacturer in the Arabian
Gulf Region today, catering to a wide range of industrial sectors. SAUDICRANES is a member
of the Konecranes Group of Companies with headquarters in Finland, who are the world’s
leader in crane & hoist industries.
SAUDICRANES receives complete engineering & service support from Konecranes along with
all mechanical and electrical components. All structures are manufactured in SAUDICRANES-
Jubail Industrial City plant, and the complete cranes & hoists are then assembled and tested
at its works prior to shipment, as required by client.
We hope you find our offer competitive and in line with your expectations. Should you need
more information or clarification, we would be glad to discuss with you any part of our technical
& commercial offers to ensure our mutual satisfaction.
As the leading crane & hoist company in the Region today, with the best experience in Royal
Commission and other special projects, we look forward to receiving your valued order, and
working with you towards the success of your projects.
Thank you and best regards,
SAUDICRANES & STEELWORKS FACTORY, LTD.
Elmer T. Fabros
Area Sales Manager
Mobile #050-394-2328
Page 1 of 4
ANNEXURE 1:
TECHNICAL SPECIFICATIONS
A) TOP-RUNNING SINGLE-GIRDER ELECTRIC OVERHEAD TRAVELING CRANES
Page 2 of 4
Operating Voltage : 380V, 3Ph, 60Hz (assumed power supply provided by client; to be confirmed
during design finalization)
Motors : Squirrel cage induction motor suitable for industrial / maintenance duty
application, suitable for the specified area
Brakes : Heavy-duty, fail-safe, electromagnetic disc brakes provided, integral with each
motor
Hook : Forged steel material; Single crook hook with safety latch
Limit Switch : Provided for all hoist, and travel motions as per our standard; 2-step for all
horizontal travel motions
Crane Runway Rail : Solid-steel flatbar-type Crane Rails for two sides of runway length
Cross Travel : Flexible festooned cable systems for power & control electrification along the
Conductor System crane bridge span & along straight monorail beam
Bumpers : Rubber bumpers provided for hoist trolley & crane end trucks
Painting : As per our standards. The crane structures shall be blasted & coated with
Amerlock 400C High-performance, High-solids Epoxy Coating System.
Standard Finish Color: Melon Yellow RAL 1028.
Excluded in : Crane Runway & Hoist Monorail I-beams & their supports / base plates+anchor
Saudi Cranes’ Scope bolts, platforms & ladders; other related civil / structural works (by building/civil
sub-contractor);
Main Isolator Switch & Rising Cable (by building/electrical sub-contractor);
any accessory below hook
Page 3 of 4
ANNEXURE 2:
PRICE SCHEDULE
Item Price, Saudi Riyals
Description Qty.
No. DDP/FOT Jubail Site
3.5ton x 9.2m. span Single-Girder Electric Overhead Traveling 1
OH Crane, as per enclosed technical specifications Set
111,900
TC- PVC-enclosed 4-busbar type powerline system (100A.) for 1
Crane runway length of 30 meters Lot
8,500
1
Solid-steel flatbar-type Crane Rails for Crane runway length of 1
30 meters Lot
8,000
2ton x 13.3m. span Single-Girder Electric Overhead Traveling 1
OH Crane, as per enclosed technical specifications Set
100,850
TC- PVC-enclosed 4-busbar type powerline system (100A.) for 1
Crane runway length of 30 meters Lot
8,500
2
Solid-steel flatbar-type Crane Rails for Crane runway length of 1
30 meters Lot
8,000
Grand Total Price - - - 245,750
2. We guarantee our cranes & hoists for one year from date of commissioning or up to 18months from
delivery date, whichever comes first.
Should you require Warranty Period extension, the additional costs shall be 5% of equipment price for
every year of extension.
3. Commissioning/start-up spares, and special tools are not required for our cranes.
Recommended Spare Parts could be quoted later, if required.
5. Delivery Time: Approx. 18 weeks from receipt of downpayment, and approval of General
Arrangement Drawings.
6. Validity of This Offer: Until one (1) month from now, subject to our written confirmation thereafter.
Notes:
1) After award of contract, before crane & hoist manufacturing, General Arrangement Drawinsg in the required format showing
pertinent specifications and dimensions shall be prepared and submitted by us for Client’s review and approval. These General
Arrangement Drawings shall confirm the cranes’ & hoist’s capacities and dimensions, after the heaviest load-weights and building
structures’ dimensions are finalized.
2) The cranes & hoist shall be assembled & wired up at Saudi Cranes’ Jubail plant. Before dispatch, they could be tested, including
125% load tests, in the presence of client’s representatives, if Factory Acceptance Tests (FAT) are required. They could be
delivered in “ready-to-install” condition, wherever possible via land transport. Hence, erection at site is not a complicated process.
Thus, we are quoting only Supervisory Services for site activities, if required.
3) Documents submitted after hoist delivery & commissioning:
a) Operating, Parts and Maintenance Manuals d) Certificate of Warranty
b) Test Certificates and Reports e) List of Recommended Operational Spare Parts, if required
c) Electrical Wiring Diagrams f) As-Built General Arrangement (Layout) Drawings
* * * * *
Page 4 of 4
JULY 9, 2013
R. G. C. K.
RADICON-GULFCONSULT & KENTZ ENG. INT’L. LTD.
Tel.: 03-899-5061 Fax. 03-899-4850
Dear Sir,
SR. 1,791,242.00
SAUDI RIYAL ONE MILION SEVEN HUNDRED NINTY ONE THAUSAND AND TWO
HUNDRED FORTY TWO ONLY.
Best regards,
Best regards,
Page 1 of 2
PRICE BREAKDOWN
SUB-TOTAL 1 1,713,742.00
TRAFFIC ROAD SIGNS – SUPPLY ONLY
SUB-TOTAL 2 77,500.00
NOTE: The Above Quantities are Estimates only, Final Invoice will be
based on actual Joint-Measurement quantities
Page 2 of 2
ISO9001:2008 certified manufacturer
QUOTATION
Ref. #: RGCK130325
QUANTITY FOB CHINA MAIN PORT
DN ITEM
PCS m USD/M USD
Technical Specification:
z Pipes offered will be ductile iron as per ISO2531-1998, T Type joint, K9, effective length: 5.7m/pc.
z Internal cement mortar lining comply with ISO4179, external sprayed metallic Zinc coating (min.130g/m2)
1. Price: Prices are valid only for the total quantity offered. Any changes in quantity and or in the product
2. Packing: In 6x20’GP.
4. Production Period: Within 25days after the receipt of T/T advance payment and original workable L/C.
5. Delivery Date: Within 35days after the receipt of T/T advance payment and original workable L/C.
7. Validity of Quotation: Until APR.10, 2013. Prices remain valid only during the validity of the offer. Beyond the
-1-
ISO9001:2008 certified manufacturer
Wallace Zhao
Sales Manager / Ductile Iron Pipe & Fittings Dept.
Tel: +8610 6879 6501 Fax: +8610 6879 6655 Mobil: +86 13811830634 E-mail: wallacezhao@okorder.com
Website: www.cmaxpipe.com
-2-
TELEPHONE#:(966-3) 3416666 FAX#:(966-3) 3411566
P.O.BOX 10047, Jubail 31961, Saudi Arabia
QUOTATION
SEND TO :SPS SENDER :AHMAD D.KAEEN
Gentlemen:
With reference to your request for a quotation on the above subject, we are pleased to
submit our offer as follows:
1. Electric heater.
2. 2`` double skin horizontal supply.
3. Backward curved fan.
4. Adjustable high/low pressure switch fan cycling switch.
5. Pump down solenoid valve.
6. Volt free contact.
7. Replaceable core filter drier shut off valve.
8. Pressure gauges (suction discharge).
9. Condenser pressure releif valve.
10. Bag pre filter section ( double skin).
11. Mixing box ( double skin).
12. Manual F/R air damper.
13. Unit full guard.
14. Stainless steel drain pan.
15. Belt guard.
16. Differential pressure switch for filters.
17. External overload for condenser fan.
18. Extended regreasing line for fan motor.
19. Marine light for fan section.
20. Sight glass.
21. Stainless steel unit name plate.
22. 7 day programmable thermostat.
1
Unit Price Total Price
Item Tag Number Model Air Flow (L/S) Cooling Cap.(KW) Electric.Heater (KW) ESP ( Pa) Qty
(SR) (SR)
1 PACU1A&1B .PAX035 4580 113.85 30 500 128,503 2 257,006
2 PACU2A&2B .PAX008 1359 23.56 10 250 49,268 2 98,536
Total : 355,542
B. PRICE: Our total price to supply the above mentioned equipment shall be: SR.355,542
FOB, Z.A.C, Jubail warehouse.
C. Terms of Payment: 25% down payment with official purchase order and balance amount
payable through letter of credit / cash / certified cheque as and where applicable
depending upon the product type and nature of sales. Payment of 100% of the agreed
price shall be made / completed by Buyer, prior to the delivery of goods without any
right of retention or reduction, unless agreed by Seller in writing. If payment in
not made on time, Seller shall be entitled to charge a late payment fee at the rate
of 1% of the outstanding amount for each month or part thereof the payment is
overdue, until full payment is received. After 90days from the payment due date, any
expenses incurred by Seller in collecting past due amounts shall be for the account
of Buyer.
1. General: The terms and conditions of sale are as set forth herein. Terms and
conditions included in the solicitation or otherwise proposed by the Buyer
shall be excluded from the contract unless accepted by seller in writing. No
contract shall result from this quotation unless Buyer`s order is acknowledged
and confirmed by seller in writing. Buyer`s acceptance must be communicated in
writing. Any order shall be subject to credit approval.Each order shall be
deemed a separate contract.
2. Prices:Unless stated otherwise, prices are stated in Saudi Riyals or US
Dollars.Prices are made according to the prevailing prices at the time of
quotation.Seller reserves the right to change typographical or clerical errors
at any time upon notice in writing.
3. Shipment and Delivery:Unless specifically agreed in writing, shipment dates
quoted are estimates and seller does not guarantee a particular date for
shipment or delivery of the goods. Unless designated otherwise, goods are
quoted ex-seller`s warehouse. The delivery period shall begin on the date a
firm order with advance payment or letter of credits is received from
buyer,unless otherwise agreed to in writing. Seller accepts no liabilities
associated with a failure by Buyer to provide sufficient information to provide
without delay in the execution of the order, and until the instructions for
shipment and delivery are agreed. Partial shipments are authorized. Warehousing
charges at the rate of 1% per week will be applicable on Buyer, if goods not
collected within agreed time period.
4. Acceptance of Goods:Buyer shall inspect the goods on seller`s warehouse before
shipment is effected. Seller shall not be responsible for any damages resulting
from offloading and rigging at buyer`s site.
5. Cancellations:If the Seller, on Buyer`s request, shallagree to cancel any order
or part thereof, the Buyer shall reimburse the Seller for costs and expenses
which arise as a result of the cancellation. In the event of cancellation Buyer
shall pay in full for any goods completed under the order. Seller reserves the
right to offset its cancellation costs against any payments received on the
order.
6. Changes:Work and material in addition to or different from, that stated herein,
and changes in drawings or specifications, shall be subject to seller`s
approval, and shall entitle Seller to an adjustment in the price and schedule.
7. Force Majoure:Seller shall not be liable for any losses, damages, or penalties
occasioned by late performance, nor for any deviations in performance due to
fires,strikes, labor disputes, supplier delays, governmental actions, customs
delays. Acts of nature, or any other condition beyond Seller`s control.
8. Applicable Law : Any agreement arising from this quotation shall be governed
by, and constructed in accordance with, the laws of the Kingdom of Saudi
Arabia.
2
STANDARD WARRANTY TERMS
PRODUCT
Compressor Parts Labor
PAX 1.5 1.5 1.5
F. VALIDITY: This offer is valid for thirty (30) days from above date.
We trust our offer meets with your requirements. However, should you need any further
information/clarifications/assistance, please feel free to contact us.
AHMAD D.KAEEN
Sales Engineer
16435, M
3
Delivery method UPS
Quotation 92432 Delivery lead time
Payment Terms Pro forma invoice
Our ref. : Kenny Laidlaw Currency GBP
Company. : RGCK Consulting
Date of Quotation 28/1/2013
Engineers
Your ref. : Jahangeer Basha Valid until 27/02/2013
Reference
Product no. Product description Qty. Unit price Discount % VAT % Total ex-VAT
OMEGA-WE -SDC-50 Full bore, Helix Woltmann type meter 1 388.18 0.00 0.00 388.18
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 50mm (2") Pipe
Diameter
OMEGA-WE -SDC-65 Full bore, Helix Woltmann type meter 1 428.88 0.00 0.00 428.88
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 65mm (2 1/2") Pipe
Diameter
OMEGA-WE -SDC-80 Full bore, Helix Woltmann type meter 1 472.72 0.00 0.00 472.72
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 80mm (3") Pipe
Diameter
OMEGA-WE -SDC-100 Full bore, Helix Woltmann type meter 1 566.62 0.00 0.00 566.62
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 100mm (4") Pipe
Diameter
1/3
OMEGA-WE -SDC-125 Full bore, Helix Woltmann type meter 1 582.28 0.00 0.00 582.28
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 125mm (5") Pipe
Diameter
OMEGA-WE -SDC-150 Full bore, Helix Woltmann type meter 1 757.58 0.00 0.00 757.58
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 150mm (6") Pipe
Diameter
OMEGA-WE -SDC-200 Full bore, Helix Woltmann type meter 1 1270.98 0.00 0.00 1270.98
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 200mm (8") Pipe
Diameter
OMEGA-WE -SDC-250 Full bore, Helix Woltmann type meter 1 2620.18 0.00 0.00 2620.18
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 250mm (10") Pipe
Diameter
OMEGA-WE -SDC-300 Full bore, Helix Woltmann type meter 1 4260.54 0.00 0.00 4260.54
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 300mm (12") Pipe
Diameter
OMEGA-WE -SDC-400 Full bore, Helix Woltmann type meter 1 6533.24 0.00 0.00 6533.24
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 400mm (16") Pipe
Diameter
2/3
OMEGA-WE -SDC-500 Full bore, Helix Woltmann type meter 1 7293.92 0.00 0.00 7293.92
suitable for cold water. The
Omega-WE-SDC is a "super dry" dial type
meter with a 360° rotating display. Suitable
for Drinking water (75/33/EEC). Maximum
temperature +30°C 500mm (20") Pipe
Diameter
OMEGA-PULSE Pulse Output option on Omega Flowmeters 1 50.00 0.00 0.00 50.00
International details:
Account number: 40458772 Sort Code: 82-61-13 IBAN: GB19 CLYD 826113 404587 72 Swift: CLYDGB2S
3/3