Sei sulla pagina 1di 3

Page 1 of 3

09/29/2018
10:58:40 PM
PI
Job: LimconJob -- Connection: UB406

End plate: 170x25x440 Gr.S275


Flange weld: 8 FW/440 - Web weld: 6 FW/440
8
Bolts: 8 x M20 8.8/N in 2 cols. at 100 gauge

70

199
85

Gr.S275
UB406X140X39 UB406X140X39
88
C1 B1

85

6
Plates: 14.7 kg
Bolts: 3.6 kg
8 Welds: 0.3 kg

Geometry Check:
*** WARNING -- Bolts not tensioned.
1 warning.

LIMCON V3.63.2.6 {0} 29-SEP-18


22:57:57
Connection: UB406
Type: Bolted Moment End Plate
D - Apex connection or splice
Country: UK
Units: SI metric
Design code: ANSI/AISC 360 (LRFD)

Beam 1: Mark=B1 Section=UB406X140X39 Grade=S275 Angle= 0.00˚


d = 398 mm Root rad. = 10 mm Fyf = 275 N/mm2
b = 142 mm Area = 4970 Fyw = 275 N/mm2
tf = 8.6 mm Sx = 629000 Fu = 430 N/mm2
tw = 6.4 mm Zx = 724000
.Section moment strength . . . . 179.2 kN.m Note 1
.Section shear strength . . . . . 420.3 kN A360 (G2-1)
.Section tension strength . . . . 1230.1 kN A360-(D2-1)
.Section compression strength . . 1098.6 kN A360 E7

End plate:
440x170x25 Gr./Fy/Fu=S275/27/430N/mm2
Beam to end plate angle . . . . . 90.00˚

End plate welds:


8 FW/440N/mm2 flanges.
6 FW/440N/mm2 web.

Bolts:
4 x M20 8.8/N top flange, 100 gauge.
4 x M20 8.8/N btm. flange, 100 gauge.

BILL OF MATERIALS
Plates:
1 no. - 440x170x25 Grade=S275 . . . . . . . 14.7 kg

LIMCON V3.63.2.6 C:\Users\Public\Documents\Limcon\LimconJob


Page 2 of 3
09/29/2018
10:58:40 PM
PI
Job: LimconJob -- Connection: UB406

Bolts:
8 no. - M20 8.8/N x 60 long . . . . . . . . 3.6 kg
Welds:
567 mm - FW 8 fu=440N/mm2 . . . . . . . . . 0.1 kg
762 mm - FW 6 fu=440N/mm2 . . . . . . . . . 0.1 kg
Total mass of welds . . . . . . . . . . . . 0.3 kg

MINIMUM ACTION CHECK


(Minima are based on section capacity, not member capacity.)
Specified minimum design actions:
Bending 50% of øMs ( 179.2) = 89.6 kN.m
Shear 0% of øVs ( 420.3) = 0.0 kN
40.0 kN
Tension 0% of øNs ( 1230.1) = 0.0 kN
Compression 0% of øNc ( 1098.6) = 0.0 kN
NOTE: Input design actions are not automatically increased if they are less than
the specified minimum actions. Minimum actions may be set in any load case.
This check warns if any design action is less than the specified minimum
for all load cases.

INPUT DESIGN ACTIONS


Beam 1: Moment, Mu . . . . . . . 150.0 kN.m
Shear, Vu . . . . . . . 150.0 kN
Axial, Pu . . . . . . . 0.0 kN

SECTION ANALYSIS RESULT


Simplified analysis:
Beam 1... Puft = 385.2t Pufc = 385.2c
Puwt = 0.0 Puwc = 0.0
Muw = 0.00
Vuw = 150.0
Elastic analysis:
Beam 1... Puft = 294.5t Pufc = 294.5c
Puwt = 0.0t Puwc = 0.0
Muw = 35.3
Vuw = 150.0
Plastic analysis:
Beam 1... Puft = 284.8t Pufc = 284.8c
Puwt = 0.0t Puwc = 0.0
Muw = 39.1
Vuw = 150.0

NOTE: Simplified analysis results used.

BOLT ARRANGEMENT
4-Bolt Flush End Plate
Connection checked for tension at top flange.

Using AISC/ASI model...

Ref. 18: Steel Design Guide 16 (SDG16)


Flush and Extended Multiple Row Moment End Plate Connections
T.M. Murray & W.L. Shoemaker - AISC - 2002
Ref. 19: Steel Design Guide 4 (SDG4)
Extended End Plate Moment Connections - Seismic and Wind Applications
T.M. Murray & E.A. Sumner - AISC - 2004
Ref. 41: Design Guide 10 - Bolted Moment End Plate Beam Splice Connections (DG10)
T.J. Hogan & N. van der Kreek - ASI - 2009

GEOMETRY CHECKS
CHECK 1 - Detailing Requirements:
Bolt UTS . . . . . . . . . . . . 800 ≥ 800 Yes
End plate width, bi . . . . . . . 170 ≥ 155 Yes
170 ≤ 193 Yes
NOTE: Clearances should be checked in virtual reality view.

DESIGN STRENGTH CHECKS


Strength ratio NNNNNNNNNO
Required strength O P
┌NDesign strength P P Reference
P P P RRRRRRRRRRRRRR
Section Bending/Axial:
Flange tension yield strength . . . . . . . 301.8 ≥ Puft = 284.8 1.06 Pass Manual p.55
Flange tension rupture strength . . . . . . 393.3 ≥ Puft = 284.8 1.38 Pass
Flange compression strength . . . . . . . . 301.8 ≥ Puft = 284.8 1.06 Pass

CHECK 2 - Flange Welds:


Flange width . . . . . . . . . . 142 mm

LIMCON V3.63.2.6 C:\Users\Public\Documents\Limcon\LimconJob


Page 3 of 3
09/29/2018
10:58:40 PM
PI
Job: LimconJob -- Connection: UB406

Total fillet weld length . . . . 277 mm SDG4 p.38


For 8 FW/440N/mm2 both sides...
NOTE: Using 50% directional strength increase. A360 (J2-5)
Fillet weld strength . . . . . . 1.680 kN/mm
Flange fillet weld tension strength . . . . 465.7 ≥ Puft = 385.2 1.21 Pass
Flange fillet weld compression strength . . 465.7 ≥ Pufc = 385.2 1.21 Pass

CHECK 3 - Web Welds:


Web shear force . . . . . . . . . 150.0 kN
Web axial force . . . . . . . . . 0.0 kN
Web bending moment . . . . . . . 0.00 kN.m
Length of web weld . . . . . . . 381 mm
NOTE: This check uses method from AISC SDG 16 (Ref. 18).
Length for shear resistance . . . 190 mm
For 6 FW/440N/mm2 both sides...
Web fillet weld shear strength (2 sides) . 319.9 ≥ Vu = 150.0 2.13 Pass
End plate design moment, Mueq . . 150.0 kN.m
Section moment strength . . . . . 179.2 kN.m
Beam moment utilization ratio . . 84%
Beam web axial strength . . . . . 1.584 kN/mm
» Web weld design force . . . . . 1.326 kN/mm
NOTE: Using 50% directional strength increase. A360 (J2-5)
Fillet weld strength . . . . . . 1.260 kN/mm
Web fillet weld axial strength (2 sides) . 2.520 ≥ puw = 1.326 1.90 Pass

CHECK 4 - Bolts at Tension Flange:


Single bolt tension strength . . 146.1 kN A360-T:J3.2
No. bolts effective at flange . . 4
Sum of bolt lever arms . . . . . 562 mm
End plate design moment, Mueq . . 150.0 kN.m
Tension bolt moment strength, øMnp . . . . 164.3 ≥ Mueq = 150.0 1.10 Pass

CHECK 5 - Bolts in Shear:


Total shear resisted by bolts . . 150.0 kN
Single bolt shear strength . . . 87.7 kN A360-T:J3.2
No. bolts effective in shear . . 4
Bolt shear strength, øRn . . . . . . . . . 350.6 ≥ Vb = 150.0 2.34 Pass SDG4 (3.17)
End plate bolt bearing strength, øRn . . . 1548.0 ≥ Vb = 150.0 10.3 Pass SDG4 (3.18)

CHECK 6 - End Plate in Bending:


End plate design moment, Mueq . . 150.0 kN.m
Yield line parameter, Yp . . . . 2032 mm
End plate yield strength, øMpl . . . . . . 251.5 ≥ Mueq = 150.0 1.68 Pass
Bolt moment strength, øMbt . . . 164.3 kN.m
» No prying strength, Mmin . . . 182.4 kN.m
» End plate no prying thickness . 19 mm SDG4 (3.10)
Is plate strong enough for no prying? . . . 251.5 ≥ 182.4 Yes
» Bolt prying may not occur.
Bolt rupture strength (no prying) . . . . . 164.3 ≥ Mueq = 150.0 1.10 Pass

CHECK 7 - End Plate in Shear:


No bolts outside tension flange » check not required.

CHECK 8 - End Plate Stiffener:


No stiffener.

CHECK 9 - End Plate Stiffener Welds:


No stiffener.

NOTES:
1. Flexural yield capacity ignoring section slenderness.

CRITICAL LIMIT STATE . . . Flange tension yield strength


UTILIZATION RATIO . . . . 94%
STRENGTH RATIO . . . . . . 1.060 Pass

LIMCON V3.63.2.6 C:\Users\Public\Documents\Limcon\LimconJob

Potrebbero piacerti anche