Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Circuit Description
The ECM is a computer that is responsible for engine control, diagnostics, and user features.
Component Location
The ECM is bolted to the control valve body on the left side of the engine.
Shop Talk
This is a fault with the internal memory of the ECM. This fault can be caused by a power
interruption to the ECM or a total loss of battery power.
Fault Code 346 can be caused by not following the correct engine shutdown procedure.
If a master disconnect switch is being used, you must turn the keyswitch OFF, wait 30
seconds, then disconnect the batteries using the master disconnect switch. If the
operator does not wait 30 seconds before disconnecting the batteries, Fault Code 346
will be logged.
If Fault Code 346 is active, turn the keyswitch ON, then turn it to OFF and wait 30
seconds. Repeat this step three times with a 30-second delay between each key cycle.
CAUTION
To reduce the possibility of damaging a new ECM, all other active fault
codes must be investigated prior to replacing the ECM.
CAUTION
To reduce the possibility of pin and harness damage, use the following
test lead when taking a
measurement:
Part Number 3822758 - male Deutsch/AMP/Metri-Pack test lead.
Troubleshooting Steps
STEPS SPECIFICATIONS
STEP 1. Check the equipment battery ?
system.
? STEP 1A. Inspect the battery cable No damaged connections
connections.
? STEP 1B. Check the battery 17.3 to 34.7 VDC (24-VDC system)
voltage.
STEP 2. Check the OEM harness. (The ?
following steps have been
constructed for generic OEM
troubleshooting of the OEM circuit.
Refer to the OEM manual for more
details.)
? STEP 2A. Inspect the OEM No damaged connections
harness fuse connections.
? STEP 2B. Check the OEM harness Less than 10 ohms
fuse.
? STEP 2C. Inspect the OEM No damaged pins
harness and ECM connector pins.
? STEP 2D. Check for an open circuit Less than 10 ohms
in the unswitched battery supply
circuit.
? STEP 2E. Check for a short circuit More than 100k ohms
from pin to pin in the unswitched
battery supply circuit.
STEP 3. Check the engine harness. ?
? STEP 3A. Check the engine No damaged connections
harness ground connection.
? STEP 3B. Inspect the engine No damaged pins
harness and ECM connector pins.
Conditions
Action
Corrosion
Loose connection.
OK NOT OK
No damaged connections Repair the damaged connections. Refer to
the OEM manual.
Go to 1B Go to 4A
Conditions
Action
OK NOT OK
17.3 to 34.7 VDC (24-VDC system) Refer to Procedure 019-087 the Battery
Voltage Low symptom tree in the
Troubleshooting and Repair Manual, QSK19
Series Engines, Bulletin 3666098, the
Troubleshooting and Repair Manual, QSK23
Series Engines, Bulletin 4021375,the
Troubleshooting and Repair Manual, QSK45
and QSK60 Series Engines, Bulletin
3666261, or the Troubleshooting and Repair
Manual, QSK78 Series Engines, Bulletin
3666727.
Go to 2A Go to 4A
Conditions
Action
Corroded fuses
Loose fuses.
OK NOT OK
No damaged connections Repair damaged connections
Go to 2B Go to 4A
Conditions
Action
OK NOT OK
Less than 10 ohms Replace the fuses. Refer to Procedure 019-
198 in the Troubleshooting and Repair
Go to 2C Go to 4A
Guided Step 2C - Inspect the OEM harness and the ECM connector pins.
CAUTION
To reduce the possibility of damaging a new ECM, all other active fault
codes must be investigated prior to replacing the ECM.
Conditions
Action
Corroded pins
Bent or broken pins
Pushed back or expanded pins
Moisture in or on the connector
Missing or damaged connector seals
Dirt or debris in or on the connector
pins.
OK NOT OK
No damaged pins Repair the damaged pins. Flush the dirt,
debris, or moisture from the connector pins.
Repair or replace the OEM interface
harness, or replace the ECM, whichever has
the damaged pins.
Go to 2D Go to 4A
Guided Step 2D - Check for an open circuit in the unswitched battery supply
circuit.
CAUTION
To reduce the possibility of pin and harness damage, use the following
test lead when taking a
measurement:
Part Number 3822758 - male Deutsch/AMP/Metri-Pack test lead.
Conditions
Action
OK NOT OK
Less than 10 ohms Repair or replace the OEM interface harness
Go to 2E Go to 4A
Guided Step 2E - Check for a short circuit from pin to pin in the unswitched
battery supply circuit.
CAUTION
To reduce the possibility of pin and harness damage, use the following
test lead when taking a
measurement:
Part Number 3822758 - male Deutsch/AMP/Metri-Pack test lead.
Conditions
the battery.
Action
OK NOT OK
More than 100k ohms Repair or replace the OEM harness or OEM
interface harness
Go to 3A Go to 4A
Conditions
Action
Broken connections
Corroded connections
Loose connections
Excessive paint, oil, or dirt.
OK NOT OK
No damaged connections Repair or replace engine harness
Go to 3B Go to 4A
Guided Step 3B - Inspect the engine harness and ECM connector pins.
CAUTION
To reduce the possibility of damaging a new ECM, all other active fault
codes must be investigated prior to replacing the ECM.
Conditions
Action
Corroded pins
Bent or broken pins
Pushed back or expanded pins
Moisture in or on the connector
Missing or damaged connector seals
Dirt or debris in or on the connector
pins.
OK NOT OK
No damaged pins Repair the damaged pins. Flush the dirt,
debris, or moisture from the connector pins.
Repair or replace the engine harness, or
replace the ECM, whichever has the
damaged pins.
Go to 3C Go to 4A
Guided Step 3C - Check for an open circuit in the block ground circuit.
CAUTION
To reduce the possibility of pin and harness damage, use the following
test lead when taking a
measurement:
Part Number 3822758 - male Deutsch/AMP/Metri-Pack test lead.
Conditions
Action
OK NOT OK
Less than 10 ohms Repair or replace the engine harness
Go to 4A Go to 4A
Conditions
Action
OK NOT OK
Fault Code 346 inactive Download the correct calibration.
Go to 4B Go to 5A
Conditions
Action
OK NOT OK
All fault codes cleared Troubleshoot any remaining active fault
codes.
Conditions
Action ?
download calibration.
OK NOT OK
Download successful Check communication connections and retry
download
Repair complete Go to 5B
CAUTION
To reduce the possibility of damaging a new ECM, all other active fault
Conditions
Action ?
OK NOT OK
Fault Code 346 inactive Replace the ECM. Refer to Procedure 019-
031.
Go to 5C Go to 5A
Conditions
Action ?
OK NOT OK
All fault codes cleared Troubleshoot any remaining active fault
codes.
Copyright? 2003
Cummins, Inc.
All rights reserved