Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
2005.06.27
Jinha Hwang
E-Mail: lghwang@lge.com Display Div. SCR Gr.
No image in the specific area (see the screen location2)
Non-image
Fig
Fig #2
#2 Non-image white
Examples. Partially displayed
2. Known Tips as to no data and partial display
No image/Data COF IC.
1) This is caused by X Board out put IC being defective. When COF IC’s have data this means the data transfer between the
Controller PCB and X Board is missing
2) Check all related X Board connections.
3) Replace that X Board or CTRL PCB or both if needed.
Fig
Fig #4
#4
Fig
Fig #5
#5 Fig
Fig #6
#6
Bottom left 3/10 of the screen with vertical bar Bottom left 3/10 of the screen with no-picture
Fig
Fig #7
#7
Related
Related X-Board
X-Board power
power supply
supply voltage
voltage check
check
X- Left X Top - Center X Top - Right
Related
Related XX Board
Board Connector
Connector check
check -Ve
VSC
V setup -Vy
Related
Related XX Board
Board &
& Connector
Connector check
check Y-SUS
VS
Z-SUS
VSC Board
Va
Controller Board
Related
Related X-Board
X-Board replacement
replacement Tuner Board
Module
Module (Panel)
(Panel) check
check X- Left X- Left X-Right
screen screen
screen
screen
screen screen
As the above, the space charging screen display is allocated for each X Board ( XL_TOP, XL_CNT,
XL_BOT, XR_TOP, XR_CNT, XR_BOT ).
Thus, if the occurring screen problems are limited only to the space X B/D,
For example, regular vertical line or abnormal screen in Data COF IC unit, Data COF unit can be the
problems of X B/D.
The inspection method will be explained in next chapter how to inspect when screen display doesn’t
work at all about each X B/D, giving examples of XL_Top B/D.
2) Replace Y-Board
Fig
Fig #8
#8
42” X 40” X
Y Y Y
Fig
Fig #9
#9
Y-Board
Y-Board &
& Y-Drive
Y-Drive Board
Board Connector
Connector check
check
Y-Drive
Y-Drive Board
Board (TOP)
(TOP) Drive
Drive IC
IC check
check
Y-Drive
Y-Drive Board
Board replacement
replacement
Fig
Fig #10
#10
Fig
Fig #10
#10
X- Left X Top - Center X Top - Right
-Ve
VSC
V setup -Vy
VS
Y-SUS VSC Board Z-SUS
Va
Controller Board
Tuner Board
-. Panel tsself defect There can be several line in ¼ inch wide area
-. Data COF FPC attached to panel is open or short. It can be screen on the both side, right and left.
-. Data COF attached to panel itself is defective. The area is sometimes over ¼ inch wide
Fig
Fig #12
#12
7. One or more horizontal lines in the screen
8. Regular vertical lines in the whole screen. (mainly in one specific color, regular line is flicking)
1) This problem is related to CONTROL PCB
2) Replace CONTROL PCB
Fig
Fig #12
#12
11. Input signal is white pattern but other colors are displayed in spots, missing data.
1) Check the slope & waveform of Y-Board and set up, set down
2) Check the slope of Z-Board’s ramp waveform
3) Measure each Board’s output waveform by over 200MHz Oscilloscope and reference Fig12 and 13.
It is possible to control Y-Board’s set up slope by adjusting VR2 and Z-Board’s ramp slope by adjusting VR1.
Fig
Fig #12
#12 Fig
Fig #13
#13
Y-Board measurement point : B61 (SUS_UP OUT PUT) Z-Board measurement point : B61 (SUS_UP OUT PUT)
V-setup
(200V~240V) 20±5uS 3±2uS
Vcc(90~110V)
Vs(170~185V)
Vs(170~185V)
OV
10V 23uS
140uS 170±5uS
Y Sustain voltage wave Z-Ramp voltage wave
OLD NEW
3 Vz ( Vs-12V )
SUS_DN 4
RAMP Connected
1-b 2-a to PANEL.
E/R_UP
Z_SUS_OUT
E/R_DN
2-b
`
Z-Board Operation Principles
■Schematic Diagram of Z Sustain Board
Vs Vzb
LM317
Vs
VR
ER_UP
Z bias
SUS_UP
L RAMP
_UP
Picture is dark and wrong discharge(phenomenon) Picture is dark and wrong discharge(phenomenon)
Check
Check the
the B+
B+ terminal
terminal &
& Cable
Cable connector
connector
IPM
Connector
Connector ofof badness
badness ::
Picture
Picture is dark & has too
is dark & has too much
much noise
noise
Check
Check the
the Z-Board
Z-Board and
and cable
cable connector
connector
Picture is dark and wrong discharge(phenomenon) Insert to Z-Board and X-Board linking connector is bad
V setup -Vy
Connector
Connector ofof badness
badness :: VS
Y-SUS VSC Board Z-SUS
Picture
Picture is dark & has too
is dark & has too much
much noise
noise Va
Controller Board
Tuner Board
Check
Check the
the Z-Board
Z-Board and
and cable
cable connector
connector
X- Left X- Left X-Right
IPM Vsetup
SCAN
15V(F DRIVER IC
+ )SCAN (SN755864APZP)
15V(F) SUS_UP
Er_up Sus_up Pass_top 15V(F4)
Ramp_up
15V(F)
NSCAN
Pass_btm FGND4
+ Y
15V(F3)
SUS_DN
FGND3 FGND
15V(F)
SE
+15V(F2) 15V(F2)
Ramp_dn SW
15V(F5)
Er_dn Sus_dn SE -Ve
-Vy
FGND2 FGND5
+ +
voltage LEVEL : Vs, Vsc, Vsetup, -Vy, Ve, +5V, +5V(F),15V, GND
FGND, +15V(F), FGND2, +15V(F2), FGND3, +15V(F3)
FGND4, +15V(F4), FGND5, +15V(F5), VPP
Y-Sustain Board
■ Role of Y Board
Y
0V
Set-up Scan Sustain
Set-up
Set-up □It is the process of charge form in internal wall and initial reset.
□It affects greatly wall charge form part.
Common
sustain polarity inversion (Z) 180 V 180 V
460 V 180 V 180 V 180 V 0V 180 V 70 V 180 V 0V 180 V 180 V 0V 180 V 0V 0V 180 V 0V 0V
Y Z Y Z Y Z Y Z Y Z Y Z Y Z Y Z Y Z
< Sustain
stage >
< Sustain
< Scan stage > stage > surface charge
X X X X X X X occursX between Y X
<Set0down
V 0V 70 V 70 V
the stage 0V 0 Vcharge
surface polarity0inversion
V 0V
stage> present line is occurs between and Z polarity
scanned < Erase stage >
< Set up state > Y polarity inversion by the
the state External inversion and Z voltage
operation the stage
the stage sagging the polarity inversion authorized to Z
< Scan stage > discharge occurs swelling the
swelling the voltage gradually the stage the stage wall by the voltage polarity inversion
by the voltage voltage gradually
voltage gradually and decreasing preparing for the stage other charge has authorized to Y and wall charge
authorized to
and increasing the formed wall Scan ,having increased by scan polarity inversion of Z polarity and dissipating
line Scanned polarity inversion
the amount of charge in uniform uniform cost of Nothing happens and wall charge stage and wall charge inversion part all the wall
wall charge cost without wall charge in of Y polarity of Y polarity charge
discharge discharge space inversion part inversion part
Y-Sustain Board
PDP
brightness
..... .....
CRT
brightness
time 1/60 seconds
◈ In the case of PDP, luminance control by current is difficult because of ultraviolet rays
saturation by current and visible rays saturation to the ultraviolet lays . Discharge occurs all
over the screen period and discharge frequency indicates luminous intensity.
(luminance ∝ discharge frequency)
◈ CRT indicates luminous intensity by electron beam intensity and one pixel brightens only
once on one screen.
ONE POINT Check Method 42” KK
VSC voltage
R60 both end CHECK
V-SET UP voltage
V setup -Vy
When
When there
there is
is wrong
wrong discharge
discharge effect
effect and
and VS
Y-SUS VSC Board Z-SUS
Picture doesn’t appear
Picture doesn’t appear Va
Controller Board
Tuner Board
Check
Check the
the Y-Sustain
Y-Sustain Board
Board and
and cable
cable connector
connector
X- Left X- Left X-Right
ONE POINT SVC Guide Y Board
V setup -Vy
When
When there
there is
is wrong
wrong discharge
discharge effect
effect and
and VS
Y-SUS VSC Board Z-SUS
Picture doesn’t appear
Picture doesn’t appear Va
Controller Board
Tuner Board
Check
Check the
the Y-Sustain
Y-Sustain Board
Board and
and cable
cable connector
connector
X- Left X- Left X-Right
2. The contents to check when voltage of Module Control Board 15V Line
is sagged
1) Check the Module Control Board 15V Line Short
2) Check the Y-Driver Board Short
3) Change the Y-Board and Z-Board at the same time when 15V Line voltage is sagged
about 8~9V. If only Y-Board is changed, badness can generates again.
1) If the screen isn’t displayed Scan FPC wise, it may be the problems between relevant Scan FPC and Y DRV B/D
2) Check if the connector of Scan FPC corresponding to the part that isn’t displayed is connected well with Y DRV B/D
3) Check if the Clock, Data signal of relevant Scan FPC input signal of Y DRV B/D is shorted with +5V or Ground.
4) Check if the output buffer of Y B/D related to relevant Scan Drive IC works normally.
5) Check if the signals are authorized well to relevant Scan Drive IC.
6) Check if the relevant Scan Drive IC Failed.
7) Check the PCB pattern.
Normal part
When
When setting
setting up
up to
to Y-
Y-
In
In the
the case
case of
of Driver
Driver Board,
Board, Diode
Diode
Curtain
Curtain Bar
Bar Check
Check the
the Down
Down terminal,
terminal,
it has a Short-circuit
it has a Short-circuit
In
In the
the case
case of
of When
When setting
setting up
up to to Y-Driver
Y-Driver
wrong Board, Diode Check
Board, Diode Check the the
wrong discharge
discharge
Down
Down terminal,
terminal, it
it has
has aa
Short-circuit
Short-circuit
ONE POINT SVC Guide
CURTAIN BAR Trouble Types
V setup -Vy
VS
Badness
Badness :: horizontal
horizontal bar
bar Y-SUS VSC Board Z-SUS
Va
Controller Board
Tuner Board
Check
Check the
the Y-Drive
Y-Drive Board
Board and
and module
module connection
connection film
film
X- Left X- Left X-Right
Specific part is black and has no picture Specific part is black and has no picture
V setup -Vy
VS
Check
Check the
the connection
connection Y-SUS VSC Board Z-SUS
Va
Controller Board
Tuner Board
Y-Drive
Y-Drive Board
Board
X- Left X- Left X-Right
Diode
Diode check
check Y-Sustain
Y-Sustain UP
UP Terminal
Terminal
X- Left X Top - Center X Top - Right
-Ve
VSC
Diode
Diode check
check Y-Sustain
Y-Sustain Down
Down Terminal
Terminal
V setup -Vy
VS
Y-SUS VSC Board Z-SUS
Va
Controller Board
Y-Drive
Y-Drive Board
Board Scan
Scan Drive
Drive IC
IC bad
bad ,, broken
broken or
or short
short
Tuner Board
X Data((6*2)*11=132bit
A
100MHz X clock
SSC A
(OSC) B Delay
DA/MEM
SF Mem(3)
4011 SF Mem(3)
X, Y, Z Contro 8*3
4EA
3Bit(Serial communication) 8*3
Flash Download
B 16*3
(12*3)
74LVTH
Differntial input A 541
TMDS SPTC Delay
TMDS 4Pair
LVDS 4021
LVDS 10Pair 19
42” 5Pair 74LVTH
16*3 A
16 (12*3) 541
Delay
Frame Memory
(1 Dealy)
Flash Mem A
3EA
DA/MEM
(arranged deletion) SF Mem(3)
4011 8*3 SF Mem(3)
8*3 4EA
Temp 4
Micom
Sense
X clock
Delay
74AC74
A
Demultiply dircuit
X Data((6*2)*11=132bit
-Ve
VSC
V setup -Vy
VS
Y-SUS VSC Board Z-SUS
Va
Controller Board
Tuner Board
Flicker is bad
Check
Check the
the controller
controller board
board connection
connection
Check
Check the
the controller
controller board
board B+
B+ Voltage
Voltage
Replace
Replace controller
controller board
board
Module Control Board
Check
Check the
the controller
controller board
board connection
connection
Check
Check the
the controller
controller board
board B+
B+ Voltage
Voltage
Replace
Replace controller
controller board
board
Module Control Board
MCM IC Problem
Control
Control board
board &
& VSC
VSC connect
connect cable
cable Check
Check
Check
Check the
the controller
controller board
board B+
B+ Voltage
Voltage
Replace
Replace controller
controller board
board
V setup -Vy
Check
Check the
the VSC
VSC B+
B+ Voltage
Voltage Y-SUS
VS
Z-SUS
VSC Board
Va
Controller Board
Tuner Board
Replace
Replace VSC
VSC board
board
Check
Check the
the firm
firm linking
linking X-board
X-board &
& control
control board
board X- Left X Top - Center X Top - Right
-Ve
VSC
Check
Check the
the firm
firm linking
linking X-board
X-board &
& module
module
V setup -Vy
VS
Y-SUS VSC Board Z-SUS
Va
Controller Board
Check
Check the
the COF
COF resistor
resistor
Tuner Board
Replace
Replace module
module X- Left X- Left X-Right
Check
Check &
& Adjust
Adjust :: PFC
PFC /VS
/VS /VA
/VA Voltage
Voltage to
to
X- Left X Top - Center X Top - Right
panel specification
panel specification
-Ve
VSC
Check
Check Y-Sustain
Y-Sustain Sub-amp
Sub-amp waveform
waveform
V setup -Vy
VS
Y-SUS VSC Board Z-SUS
Va
Controller Board
Replace
Replace Y-Sustain
Y-Sustain amp
amp
Tuner Board
Not
Not Resolved?
Resolved? Replace
Replace Control
Control board
board X- Left X- Left X-Right
Check
Check &
& Adjust
Adjust :: PFC
PFC /VS
/VS /VA
/VA Voltage
Voltage to
to
X- Left X Top - Center X Top - Right
panel specification
panel specification
-Ve
VSC
Check
Check Y-Sustain
Y-Sustain Sub-amp
Sub-amp waveform
waveform
V setup -Vy
VS
Y-SUS VSC Board Z-SUS
Va
Controller Board
Okey?
Okey? Replace
Replace Y-Sustain
Y-Sustain amp
amp
Tuner Board
Not
Not Resolved?
Resolved? Replace
Replace Control
Control board
board X- Left X- Left X-Right
Check
Check &
& Adjust
Adjust :: PFC
PFC /VS
/VS /VA
/VA Voltage
Voltage to
to
X- Left X Top - Center X Top - Right
panel specification
panel specification
-Ve
VSC
Check
Check Y-Sustain
Y-Sustain Sub-amp
Sub-amp waveform
waveform
V setup -Vy
VS
Y-SUS VSC Board Z-SUS
Va
Controller Board
Okey?
Okey? Replace
Replace Y-Sustain
Y-Sustain amp
amp
Tuner Board
Not
Not Resolved?
Resolved? Replace
Replace Control
Control board
board X- Left X- Left X-Right
Check
Check &
& Adjust
Adjust :: PFC
PFC /VS
/VS /VA
/VA Voltage
Voltage to
to
panel specification
panel specification
Check
Check Y-Sustain
Y-Sustain Sub-amp
Sub-amp waveform
waveform
Okey?
Okey? Replace
Replace Y-Sustain
Y-Sustain amp
amp
Not
Not Resolved?
Resolved? Replace
Replace Control
Control board
board
-Ve
VSC
V setup -Vy
VS
Y-SUS VSC Board Z-SUS
Va
Controller Board
Tuner Board
Check
Check &
& Adjust
Adjust :: PFC
PFC /VS
/VS /VA
/VA Voltage
Voltage to
to
panel specification
panel specification
Check
Check the
the connection
connection VSC
VSC &
& Control
Control board
board
Okey?
Okey? Replace
Replace VSC
VSC Board
Board
Not
Not Resolved?
Resolved? Replace
Replace Control
Control board
board
-Ve
VSC
V setup -Vy
VS
Y-SUS VSC Board Z-SUS
Va
Controller Board
Tuner Board
VSC Connector VSC Board Control Board
X- Left X- Left X-Right
Check
Check &
& Adjust
Adjust :: PFC
PFC /VS
/VS /VA
/VA Voltage
Voltage to
to
panel specification
panel specification
Check
Check the
the X-board
X-board waveform
waveform
Okey?
Okey? Replace
Replace X-
X- Board
Board
Not
Not Resolved?
Resolved? Check
Check for
for C.O.F
C.O.F IC
IC Short
Short
Check
Check &
& Adjust
Adjust :: PFC/VS/
PFC/VS/ VA
VA Voltage
Voltage to
to panel
panel
Specification
Specification
Check
Check Y-Sustain
Y-Sustain Sub-amp
Sub-amp wave
wave form
form
Okay?
Okay? Replace
Replace Y-Sustain
Y-Sustain Amp
Amp
Not
Not Resolved?
Resolved? Replace
Replace Controller
Controller Board
Board
Not
Not Resolved?
Resolved? Panel
Panel