Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Questions
Number: 4A0-104
Passing Score: 800
Time Limit: 120 min
File Version: 8.04
http://www.gratisexam.com/
4A0-104
QUESTION 1
3 Epipe services and 2 VPLS services have been configured between two PE routers. How many service
labels will be signaled in total?
A. 2
B. 3
C. 4
D. 5
E. 6
F. 10
Correct Answer: F
Section: (none)
Explanation
Explanation/Reference:
QUESTION 2
Which of the following statements are TRUE about configuring a SDP between an IES and a VPLS?
(Choose 2)
Correct Answer: BD
Section: (none)
Explanation
Explanation/Reference:
QUESTION 3
Port 1/1/1 has been configured as an access port with encapsulation dot1q on an Alcatel-Lucent 7750 SR.
Which of the following statements are TRUE? (Choose 2)
Correct Answer: DE
Section: (none)
Explanation
Explanation/Reference:
QUESTION 4
Which VPWS service would be used to create a point-to-point Frame Relay service?
A. Epipe
B. Apipe
C. Fpipe
D. Ipipe
E. Cpipe
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 5
Which routing protocol cannot be run over an Ipipe?
http://www.gratisexam.com/
A. OSPF
B. RIP
C. BGP
D. IS-IS
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
answer is valid.
QUESTION 6
Which service is needed to bridge an ATM service to an Ethernet service?
A. Apipe
B. Fpipe
C. Cpipe
D. Epipe
E. Bridge service
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 7
How many service labels must be signaled to bring up a fully meshed VPLS service among four PE
routers?
A. 1
B. 4
C. 6
D. 8
E. 12
F. 24
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 8
Which of the following most accurately describes the default behavior of a VPLS regarding the handling of a
tagged frame at the ingress of SAP 1/1/1:100?
A. The FCS is verified and the customer frame is transported intact over the service provider network.
B. The FCS is verified and kept in the customer frame. The VLAN tag is removed for transport over the
network.
C. The FCS is verified and removed from the frame. The VLAN tag is kept for transport over the network.
D. The FCS is verified and removed from the frame. The VLAN tag is removed for transport over the
network.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 9
What happens when a packet without a VLAN tag is received on a SAP provisioned with null encapsulation
while an SDP vc-type is provisioned as vlan?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 10
What distinguishes a VPLS service from a VPWS service?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 11
Which of the following statements best describes the flooding of traffic on a PE when traffic is received on a
SAP?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 12
Which of the following represents a SAP on a physical port configured with Q-in-Q encapsulation?
A. sap 1/1/1
B. sap 1/1/1:5
C. sap 1/1/1:5:5
D. sap 1/1/1:10.100
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 13
In a VPLS service, the mesh-sdp vc-id is identical to the service id by default.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 14
How many SAPs can be configured on a port configured with NULL encapsulation?
A. 1
B. 4096
C. None. This encapsulation is not supported.
D. The number is limited only by the capacity of the router
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 15
Customer 'A' has sites on 3 different Alcatel-Lucent PE routers. The routers are connected to each other
through an IP/MPLS network in a full mesh fashion. Customer 'A' requires a VPLS service. Which of the
following statements are TRUE? (Choose2)
Correct Answer: AD
Section: (none)
Explanation
Explanation/Reference:
QUESTION 16
Which of the following statements best describes the flooding of traffic on a PE when traffic is received on a
spoke SDP?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 17
What does a PE do when a frame is received in a VPLS service with an unknown destination address by
default?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 18
What is the default vc-type for an SDP on the Alcatel-Lucent 7750 SR?
A. vc-type null
B. vc-type ether
C. vc-type vlan
D. vc-type none
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 19
Which of the following best completes the sentence: "An Internet Enhanced Service is a_____________
service where the CE communicates with a ________________interface to send and receive traffic.
A. distributed/virtual
B. local/sub
C. routed/Layer 3
D. distributed/routed
E. Layer 2/loopback
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 20
Which of the following statements is TRUE?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 21
What are the two major differences between configuring an IES service and configuring VPWS or VPLS
services? (Choose 2)
Correct Answer: BD
Section: (none)
Explanation
Explanation/Reference:
QUESTION 22
An ES service can have both MAC and IP filters applied to it.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
answer is updated.
QUESTION 23
What can the sdp-ping command be used for? (Choose 2)
A. To test the ability of reaching the far-end IP address of an SDP within the SDP encapsulation
B. To determine the path MTU to the far-end IP address over an SDP.
C. To determine the service MTU of the service using an SDP.
D. To determine the presence of hosts using the service
Correct Answer: AB
Section: (none)
Explanation
Explanation/Reference:
QUESTION 24
Which of the following statements are TRUE regarding sdp-ping? (Choose 3)
Explanation/Reference:
QUESTION 25
Which OAM command can be used to verify the correct and consistent provisioning of a service between
two service end points?
A. sdp-ping
B. Isp-ping
C. sap-ping
D. svc-ping
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 26
Which of the following items can NOT be used as a mirror source?
A. A physical port.
B. ASAP.
C. Ingress MPLS frames with a specific label.
D. Entries that match an IP filter.
E. Entries that match a MAC filter.
F. All of the above can be used as a mirror source.
Correct Answer: F
Section: (none)
Explanation
Explanation/Reference:
QUESTION 27
A technician sitting in a Network Operations Center would like to set up a remote mirror on an Alcatel-
Lucent 7750 Service Router to examine some data traffic ingressing a port at a remote site. Which of the
following are required? (Choose 2)
Correct Answer: AE
Section: (none)
Explanation
Explanation/Reference:
QUESTION 28
Click on the exhibit button below.
Assuming the customer only needs to monitor traffic from PE3 to the customer site, what three items are
missing from PE3's configuration? (Assume that the IP/MPLS network structure between the local and
remote PEsis in place.)
A. The mirror destination configuration on PE5 is missing the "remote-source" command,
B. The mirror destination on PE3 needs a "remote-source" command.
C. The mirror service IDs on the local and remote destinations must match.
D. The mirror source on PE3 needs a "remote-source" command.
E. The mirror source command on the remote PE3 needs a command that tells it to monitor port 1/1/2.
Explanation/Reference:
QUESTION 29
On Alcatel-Lucent 7750 SR OS, routing information between the CE and PE can be exchanged using the
following methods.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 30
Which of the following statements is TRUE about the VRF?
A. The VRF is a virtual router on the PE router that contains the customer's routes for the VPRN
B. Each PE maintains multiple VRFs based on the number of PE peers it connects to.
C. Each PE has a VRF for each VPRN service provisioned on the router.
D. All of the above.
E. Only A and C.
F. Only A and B
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 31
Which of the following statements best describes the purpose of an MP-BGP in a VPRN?
A. Routes from different customers with the same IPv4 address prefix are treated as equivalents by MP-
BGP.
B. Alcatel-Lucent 7750 SR routers support MP-BGP for VPN label signaling in a VPRN service only if LDP
is used for LSP signaling.
C. The multi-protocol nature of MP-BGP allows VPRN routes to be distributed within the provider core
network as IPv4 routes.
D. MP-BGP is an enhanced version of BGP that can carry a service label, a tranpot label, and customer
route prefixes.
E. None of the above statements describe the use of an MP-BGP in a VPRN.
F. All of the above statements describe the use of an MP-BGP in a VPRN.
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 32
Click on the exhibit button below.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 33
Which of the following statements is NOT a valid reason to use MP-BGP as a routing protocol to transport
VPRN routes?
A. The number of VPRN routes can become very large. MP-BGP can support a very large number of
routes.
B. MP-BGP can carry routing information for a number of different address families.
C. MP-BGP is designed to exchange information between routers that are not directly connected.
This feature keeps VPRN routing information out of P-routers.
D. MP-BGP can carry additional information attached to a route as an optional BGP attribute.
E. All of the above statements are valid reasons for using MP-BGP as a VPRN routing protocol.
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 34
Which of the following statements best describes a route target?
A. A route target is a BGP extended community used to identify the VRF table for a prefix at the receiving
PE
B. A route target is a mechanism from which VPRN controls the distribution of VPN routing information.
C. Route target attributes are earned in a MP-BGP as attributes of the route.
D. A route target is used by the PE router to identify the VRF that a VPN-lPv4 prefix is associated with.
E. All of the above statements describe a route target
F. None of the above statements describe a route target
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 35
Click on the exhibit button below.
If CE1 and PE1 use BGP to exchange routing information and CE2 and PE2 use static routing to forward
traffic to and from the VPRN, which of the following statements is considered TRUE?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 36
Which of the following statements is TRUE concerning a VPRN data plane flow?
A. A data packet will receive a service label at the CE and a transport label at the ingress PE.
B. A data packet intended for a remote CE will have its service label swapped at each P router along the
path towards the egress PE.
C. At the egress PE, the transport label will be popped and the data packet forwarded with the service
label.
D. The service label is popped by the remote CE. The unlabeled packet is forwarded based on the longest
match lookup algorithm in the VRF.
E. All of the above statements are false.
F. All of the above statements are true.
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 37
Which of the following steps is mandatory when enabling an MP-BGP session between PE routers in a
VPRN?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 38
Click on the exhibit button below.
Which of the following is the correct configuration for an MP-BGP session on 6VPE1?
A. PE1>config>router>bgp#info
--------------------------------------------
group "multi-bgp"
family vpn-ipv6
neighbor 10.10.10.2/32
local-address 10.10.10.1
peer-as 64496
exit
exit
B. PE1>config>router>bgp#info
-------------------------------------------
group "multi-bgp"
family ipv6 vpn-ipv4
neighbor 10.10.10.2
local-address 10.10.10.1
peer-as 64496
exit
exit
C. PE1>config>router>bgp#info
--------------------------------------------
group "multi-bgp"
family vpn-ipv6
neighbor 10.10.10 2
local-address 10.10.10.1
peer-as 64496
exit
exit
D. PE1>config>router>bgp#info
--------------------------------------------
group "multi-bgp"
family ipv6 vpn-ipv6
neighbor 10.10.10.2/32
local-address 10.10.10.1
peer-as 64496
exit
exit
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 39
Click on the exhibit button below.
Which of the following is the correct configuration on 6VPE1 for a BGP peering session with CE1?
A. PE1>config>service>vpm>bgp#info
--------------------------------------------------- group "toCE1"
family ipv6
export "mbgp-bgp"
neighbor 2001:db8:12::1
peer-as 64497
exit
exit
B. PE1>config>service>vpm>bgp#info
--------------------------------------------------- group "toCE1"
family ipv6
export "mbgp-bgp"
neighbor 2001:db8:12:1
peer-as 64496
exit
exit
C. PE1>config>router>bgp#info
--------------------------------------------------- group "toCEl"
family ipv6
export "mbgp-bgp"
neighbor 2001 db8:12::1
peer-as 64497
exit
exit
D. PE1>config>router>bgp#info
--------------------------------------------------- group "toCE1"
family ipv6
export "mbgp-bgp"
neighbor 2001:db8:12::1
peer-as 64496
exit
exit
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 40
An operator needs to provision 6VPE on a 7750 SR that is also used to provide existing IPv4 VPRN
services. IPv6 VPRN customers use BGP as a PE-CE protocol. Which of the following statements is
FALSE regarding the configuration steps required?
A. MP-BGP sessions need to be configured in the service provider network to support a VPN- IPv6
address family.
B. PE routers must be configured to run MP-BGP and IPv6
C. PE-to-CE BGP sessions need to be configured to support IPv6.
D. The provider core must be configured to support IPv6
E. None of the above statements are false.
F. All of the above statements are false
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
Topic 2, Volume B
QUESTION 41
Which of the following best describes a VPWS?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 42
Which of the following best describes an IES?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 43
Which of the following are characteristics of a SDP? (Choose 2)
A. SDPs are a logical way to direct traffic from one router to another.
B. SDPs are a logical way to direct traffic between services.
C. SDP IDs are locally unique.
D. SDP IDs must be unique across the network.
E. SDPs are specific to one service type
F. SDPs must use MPLS for their encapsulation
Correct Answer: AC
Section: (none)
Explanation
Explanation/Reference:
QUESTION 44
The terms "customer" and "service" are used synonymously when describing a service implementation on
the Alcatel-Lucent 7750 SR.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 45
Which of the following commands is used to enable an Epipe service?
Explanation/Reference:
QUESTION 46
Epipe services do no consume any MAC resources because MAC learning is disabled.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 47
When provisioning a spoke-SDP on an Epipe, what MUST match on both ends of the service?
A. Service ID
B. Customer ID
C. SAPID
D. VC-ID
E. SDPID
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 48
Which of the following commands is used to configure a new MPLS SDP?
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 49
Which of the following commands is used to create a new Epipe service?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 50
When configuring RSVP-TE for transport tunnels, which command enables RSVP by default?
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 51
Which of the following conditions are necessary in order for service labels to be signaled between two PE
routers? (Choose 3)
Explanation/Reference:
QUESTION 52
A mesh SDP is used to create an Fpipe service.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 53
Which of the following statements are TRUE about configuring a distributed Epipe service? (Choose 2)
Correct Answer: AC
Section: (none)
Explanation
Explanation/Reference:
QUESTION 54
In a Layer 2 encapsulation, using Martini, what does the first (top) label represent?
A. Tunnel Label
B. VC Label
C. Operational Control Word
D. UNI
E. NNI
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 55
In a Layer 2 encapsulation, using Martini, what does the second (bottom) label represent?
A. Tunnel Label
B. VC Label
C. Operational Control Word
D. VPI
E. VCI
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 56
Which of the following SAPs will forward tagged frames with an outer VLAN tag of 200? (Choose 3)
A. sap 1/1/1
B. sap 1/1/1:*
C. sap 1/1/1:*.0
D. sap 1/1/1:0*
E. sap 1/1/1:200.*
F. sap 1/1/1:300:200
QUESTION 57
On which of the following is it NOT possible to configure a MTU?
A. Network port
B. Access port
C. LSP
D. SDP
E. Service
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 58
Which of the following statements best describes an FDB used in a VPLS service?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 59
A network consists of 4 PE routers. A customer requires a VPLS service and has sites connected to each
PE. Each site must have direct connectivity with all other sites. How many SDPs must be configured on
each PE?
A. 0
B. 2
C. 3
D. 4
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 60
What is a key benefit of a VPLS service?
A. The customer maintains complete control over routing.
B. The adding of new sites is simplified; no re-configuration is required at existing sites.
C. The clear demarcation of functionality between service provider and customer makes troubleshooting
easier.
D. All of the above.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 61
Which of the following defines a SAP that will select frames with an outer tag of '4' and ignore any inner lag
on a Q-in-Q encapsulated port?
A. sap 1/1/1:0.*
B. sap 1/1/1
C. sap 1/1/1:*.4
D. sap 1/1/1:4.*
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 62
Which protocol is used to signal the outer label for a VPN service?
A. RSVP
B. IPCP
C. TLDP
D. PPP
E. Either RSVP or LDP
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 63
When configuring an IES spoke termination to a VPLS, what must be explicitly configured in order for the
service to come up? (Choose 2)
Correct Answer: AC
Section: (none)
Explanation
Explanation/Reference:
QUESTION 64
Which of the following are characteristics of an IES service? (Choose 2)
Correct Answer: CD
Section: (none)
Explanation
Explanation/Reference:
QUESTION 65
What command syntax would be used to create a new IES service with a service id of 5 and a customer id
of 1000?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 66
Which of the following commands would be used to show the operational state of all IES services?
A. show service id 5
B. show service ies
C. show service service-using ies
D. show service id 5 base
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 67
Fragmentation is supported on a Layer 2 service
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 68
Which of the following commands is used in an RSVP signaled MPLS tunnel to validate the path MTU
based on signaling across the LSP?
A. Path MTU is always calculated from the MTU of the egress network port on the head end PE.
B. oam sdp-mtu
C. adspec
D. cspf
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
answer is valid.
QUESTION 69
Which of the following best describes how the path-mlu is chosen for an SDP?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 70
Click on the exhibit button below.
Assuming the customer only needs to monitor traffic from PE3 to the customer site, what two items are
missing in the configuration of PE5, the Alcatel-Lucent 7750 Service Router in the Head Office? (Assume
that the IP/MPLS network structure between the local and remote PEs is in place.)
Correct Answer: AD
Section: (none)
Explanation
Explanation/Reference:
QUESTION 71
Which of the two following statements are TRUE?
A. When an Alcatel-Lucent Service Router is rebooted, the mirror destination and mirror source must be
re-configured
B. A mirror destination is shut down by default on an Alcatel-Lucent Service Router.
C. A mirror source is shut down by default on an Alcatel-Lucent Service Router.
D. When an Alcatel-Lucent Service Router is rebooted, the mirror destination must be re- configured.
E. When an Alcatel-Lucent Service Router is rebooted the mirror source must be re-configured.
Correct Answer: BE
Section: (none)
Explanation
Explanation/Reference:
QUESTION 72
Which of the following statements is FALSE about the VPN label?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 73
Which of the following statements is TRUE concerning route distinguishes on the 7750 SR?
Correct Answer: F
Section: (none)
Explanation
Explanation/Reference:
QUESTION 74
Which of the following statements is TRUE regarding a VRF?
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 75
Which of the following statements is TRUE concerning the advertisement of VRF routes on a 7750 SR?
A. By default, a 7750 SR does not advertise all routes in the VRF to a CE router.
B. The default 7750 SR behavior describes all routes in a VRF that are advertised to other PE routers.
C. By default, a 7750 SR does not advertise all routes in the VRF to other PE routers.
D. By default, a 7750 SR advertises all routes in the VRF to a CE router.
Correct Answer: AB
Section: (none)
Explanation
Explanation/Reference:
QUESTION 76
Which of the following statements is FALSE regarding 6VPE?
A. Multiple MP-BGP sessions are required to carry VPN-IPv4 and VPN-IPv6 routes.
B. PE routers must support both IPv4 and IPv6 addresses; customer routers can use either one
C. In 6VPE, MP-BGP is used to advertise IPv6 prefixes and the associated VPRN label.
D. In 6VPE, the provider core routers are IPv6-unaware.
E. All of the above statements are true.
F. All of the above statements are false.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 77
Which of the following statements is FALSE regarding 6VPE?
A. 6VPE is a tunneling technology that makes use of MPLS tunnels to transport IPv6 information over an
IPv4 MPLS infrastructure.
B. Customers connected to 6VPE could run native IPv6 or IPv4.
C. On the PE router, the next hop for a VPN IPv6 address is an IPv6 address, regardless of the nature of
the network between the PEs.
D. 6VPE requires an IPv6-aware MPLS core.
E. Both C and D are false.
F. All of the above statements are true.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 78
Which of the following is NOT a service offered on the Alcatel-Lucent 7750 SR?
A. IES
B. VPWS
C. VPLS
D. VPRN
E. L2TP
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 79
Which of the following best describes a VPRN?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 80
Which of the following describes a service on the Alcatel-Lucent 7750 SR?
A. A logical entity that provides a uniform, end-to-end configuration, management and billing model for
provisioning either Internet or VPN connectivity.
B. Provides connectivity between customer access points.
C. A service that can either be local or distributed.
D. All of the above
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 81
Once a service has been created with a customer association, it is possible to change the customer
association.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 82
What needs to be configured before a SAP appears? (Choose 2)
Correct Answer: AC
Section: (none)
Explanation
Explanation/Reference:
QUESTION 83
All services mapped to an SDP use the same transport encapsulation type (either GRE or MPLS)
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
http://www.gratisexam.com/
QUESTION 84
A Cpipe supports both structured and unstructured frames.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 85
A service provider wishes to configure a Layer 2 service that will forward customer VLAN tags. When
configuring an SDP for the service, which vc-type will forward service delimiting tags on the ingress PE?
A. vc-type ether
B. vc-type vlan
C. vc-type dot1q
D. vc-type null
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 86
Which service type would be used to provide a bi-directional Layer 2 connection of TDM circuits over an IP/
MPLS network?
A. A-pipe
B. E-pipe
C. I-pipe
D. F-pipe
E. C-pipe
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 87
Which of the following SAP encapsulations support multiple services on a port? (Choose 3)
A. dot1q
B. null
C. qinq
D. atm
E. ipcp
F. bcp-null
Explanation/Reference:
QUESTION 88
When a tagged packet is received on a SAP configured with dot1q encapsulation, the VLAN tag must
match the value configured on the SAP in order to be forwarded.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 89
In a Layer 2 VPN service, the FCS is stripped when a customer packet arrives at the ingress PE and
regenerated on egress.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 90
By default, what does a PE do to support VPLS services for different customers? (Choose 2)
A. MAC learning.
B. Maintain a different Forwarding Data Base for each service
C. ARP mediation.
D. Maintain a different Routing Information Base for each service.
Correct Answer: AB
Section: (none)
Explanation
Explanation/Reference:
QUESTION 91
What is the minimum Ethernet physical network MTU required for a Layer 2 service on a GRE
encapsulated SDP with a service MTU of 1514?
A. 1514
B. 1526
C. 1548
D. 1556
E. 1536
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 92
A network technician needs to set up a local mirror to replicate traffic for examination with a protocol
analyzer. The analyzer is on port 1/1/4 of his service router. Which of the following configuration steps is
required?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 93
Which of the following best describes the label stack for a packet in the VPRN context?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
http://www.gratisexam.com/
QUESTION 94
Which of the following statements about VPRN is NOT true? (Choose 2)
A. VPRN is an IP service that connects multiple sites in a single routed domain over the provider-managed
IP/MPLS network.
B. Each VPRN consists of a set of customer sites that must connect to the same PE router
C. In a VPRN service, each customer router becomes a routing peer to other customer routers
D. VPRN provides customer routers with transparent IP connectivity without knowledge of the MPLS core
Correct Answer: BC
Section: (none)
Explanation
Explanation/Reference:
QUESTION 95
A VPRN service is configured with BGP used as the CE-PE routing protocol. What address families are
required on the PE-CE BGP session?
A. VPN-IPv4 address families are required in order for routes to be exchanged with the PE.
B. Only default IPv4 address families are required since the CE is not aware of the VPRN service
C. Either IPv4 or VPN-IPv4 address families can be configured on the PE-CE BGP session
D. An IPv4 address family configuration is required for the PE-PE configuration.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 96
Which of the following statements are FALSE regarding the VPN-IPv4 address family? (Choose
2)
A. When a PE router receives an IPv4 prefix from its local CE it creates a VPN-IPv4 prefix.
B. The route distinguisher (RD) is appended to the IPv4 prefix to form a 16 byte VPN-IPv4 prefix.
C. VPN-IPv4 allows BGP to distinguish multiple routes with the same prefixes originated from distinct
customers
D. VPN-IPv4 addresses are only present within the service provider network.
E. In VPRN, data traffic is carried in VPN-IPv4 packets.
Correct Answer: BC
Section: (none)
Explanation
Explanation/Reference:
QUESTION 97
Which of the following statements is FALSE regarding 6VPE?
A. 6VPE is a tunneling technology that makes use of MPLS tunnels to transport IPv6 information over an
IPv4 MPLS infrastructure.
B. Customers connected to 6VPE could run native IPv6 or IPv4.
C. On the PE router, the next hop for a VPN IPv6 address is an IPv6 address, regardless of the nature of
the network between the PEs.
D. 6VPE requires an IPv6-aware MPLS core.
E. Both C and D are false.
F. All of the above statements are true.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 98
Service tunnels and transport tunnels are bidirectional and only require the operator to configure the tunnel
on one router.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 99
A transport tunnel can either use an MPLS or GRE encapsulation.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 100
Which of the following must be configured when configuring an Epipe service? (Choose 4)
Explanation/Reference:
QUESTION 101
Which of the following best describes a local Epipe Service?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 102
Which command provides a summary status of the VPLS service 100?
Explanation/Reference:
QUESTION 103
A customer requests that their Layer 2 Ethernet service be configured to forward frames up to 1514 bytes.
The service provider is using MPLS encapsulation and RSVP-TE fast-reroute with facilities bypass on their
redundant IP/MPLS network. What is the minimum MTU setting for the network ports?
A. 1514
B. 1528
C. 1536
D. 1540
E. 1560
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 104
On a dot1Q encapsulated port, frames with a VLAN tag of 0 and untagged frames are forwarded to the null
SAP
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 105
By default, what happens when a packet with a VLAN tag is received on a SAP provisioned with null
encapsulation?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 106
Why must the MTU be changed when configuring an IES spoke termination to a VPLS?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 107
What is the best approach of making MTUs match between a VPLS and a spoke IES in order to bring up
the service?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 108
Which of the following commands can be used to compare the VC MTU signaled between two PE routers?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 109
What is the purpose of service mirroring on the Alcatel-Lucent Service Router?
A. To mirror service requirements of a customer with a single branch office and multiple remote sites
B. To utilize unused ports of a service router until they are required for a service.
C. To replicate traffic from a service port to another port for debugging or monitoring functions
D. To ease the configuration burden of services that support a large number of subscribers
E. All of the above
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 110
Which of the following statements is TRUE regarding service mirroring?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 111
Which of the following SAPs will toward tagged frames but NOT untagged frames?
A. sap 1/1/1
B. sap 1/1/1:*
C. sap 1/1/1:*.0
D. sap 1/1/1:0
E. None of the above.
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 112
Which of the following statements best describes the main difference between an Ipipe and an Epipe
interworking?
A. An Ipipe is a point-to-point Layer 2 VPN capable of only carrying Ethernet payloads. An Epipe
interworking refers to the transportation of ATM/FR traffic over an Epipe.
B. An Ipipe is used for performing Ethernet interworking with ATM/FR/PPP using bridged- PDUs. An Epipe
interworking is used for performing Ethernet interworking with ATM/FR/PPP using routed-PDUs.
C. An Ipipe is used for performing Ethernet interworking with ATM/FR/PPP using routed-PDUs.
An Epipe interworking is used for performing Ethernet interworking with ATM/FR/PPP using bridged-
PDUs.
D. None of the above.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 113
Which of the following statements best describes how an FDB is populated with MAC addresses in a VPLS
service?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 114
Which protocol is used to signal the inner label for a L2-VPN service?
A. RSVP
B. IPCP
C. TLDP
D. PPP
E. Either RSVP or LDP
F. M-BGP
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 115
An operator wishes to verify end-to-end connectivity for an individual service. What utility will he or she most
likely use?
A. sdp-ping
B. Isp-ping
C. svc-ping
D. sdp-mtu
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 116
Which of the following statements best describes the flooding of traffic on a PE when traffic is received on a
mesh SDP?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 117
How many SAPs can be configured on a port configured with dot1q encapsulation?
A. 1
B. 4095
C. None. This encapsulation is not supported.
D. The number is limited only by the capacity of the router
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 118
Choose the following components that are necessary for the configuration of a mirror service.
(Choose 2)
Correct Answer: BC
Section: (none)
Explanation
Explanation/Reference:
QUESTION 119
What command syntax would be used to create a new routed interface on an existing IES service?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 120
Which of the following best describes an SDP?
A. Acts as a logical way to direct traffic from one SAP to another on a single node.
B. Acts as a logical way to direct traffic from one service to another on a single node.
C. Acts as a logical way to direct traffic from one access port to another.
D. Acts as a logical way to direct traffic from services on one router to services on another.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 121
Which of the following commands would be used to configure a new VPLS service that will use a default vc-
id of 5 and a customer id of 4?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 122
Which of the following MUST be identical for a service between two PEs?
A. Customer ID
B. SDP ID
C. Service ID
D. VC ID
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
answer is perfected.
QUESTION 123
Which of the following about transport tunnels used by services is FALSE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 124
Which of the following about SDPs is FALSE?
A. All services bound to the same SDP must be the same service type.
B. All services bound to the same SDP will have the same transport encapsulation.
C. Any operation on an SDP will affect all services bound to that SDP.
D. An SDP is used to direct traffic for a service from one router to another.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 125
Which of the following about the components of a service on the Alcatel-Lucent 7750 SR is FALSE?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 126
Which of the following SAP encapsulations does NOT support multiple services on a port?
A. Dot1q
B. Null
C. QinQ
D. ATM
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 127
Click the exhibit.
Based on the output shown, what is the value of the service's VC ID?
A. 2
B. 12
C. 30
D. 44
E. 100
F. The VC ID Cannot be determined from the output
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 128
Which protocol is used to signal the service label for a Layer 3 VPRN service?
A. L-LDP
B. T-LDP
C. RSVP-TE
D. MP-BGP
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 129
Which of the following commands is used to enable an E-pipe service?
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 130
Which of the following can be used to detect the smallest path MTU in an RSVP signaled MPLS tunnel?
A. ADSPEC
B. CSPF
C. Service ping
D. LSP trace
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 131
Consider an E-pipe service configured with SAP 1/1/1:5 and SAP 1/1/1:6. If the SAP 1/1/1:5 accepts an
ingress frame, which of the following is TRUE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 132
The SAP 1/1/1:2.3 receives an untagged Ethernet frame. Which of the following is TRUE?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 133
A SAP configured in the form of 1/1/1:0/32 would be used for which type of VPWS?
A. A-pipe
B. C-pipe
C. E-pipe
D. F-pipe
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 134
A customer requests that their Layer 2 Ethernet service be configured to forward frames up to 1500 bytes.
The service provider is using MPLS encapsulation (without RSVP-TE fast-reroute) on their IP/MPLS
network. What is the minimum MTU setting for the network ports?
A. 1512
B. 1522
C. 1536
D. 1542
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 135
Which service type is needed to bridge an ATM-attached user and an Ethernet-attached user?
A. A-pipe
B. F-pipe
C. C-pipe
D. E-pipe
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 136
An E-pipe is configured with a service MTU of 5000. What value will be derived for the VC- MTU?
A. 4078
B. 4986
C. 5014
D. 5022
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 137
What must be configured before a SAP can be created on an E-pipe?
A. The Ethernet port must be set to network mode, and the service must have a spoke SDP.
B. The Ethernet port must be set to network mode.
C. The Ethernet port must be set to access mode.
D. The Ethernet port must be set to access mode, and the service must have a spoke SDP.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 138
A service has a null encapsulated SAP and a vc-type vlan' SDP. What happens when the SAP receives an
untagged Ethernet frame?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 139
An E-pipe is configured with a service MTU of 5000. What MTU value should be set on the access port for
a Q-in-Q encapsulated SAP?
A. 5000
B. 5004
C. 5008
D. 5018
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 140
A service needs to accept frames that have the following: an outer VLAN tag of 200 with an inner VLAN tag
of 33; and frames that have an outer VLAN tag of 250 with an inner VLAN tag of 33. What SAP(s) need to
be configured?
A. 1/1/1:200.*
B. 1/1/1:*.33
C. 1/1/1:*.*
D. This requires two SAPs: 1/1/1:200.33 and 1/1/1:250.33
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 141
Which of the following about SDPs is FALSE?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 142
By default, what does an Alcatel-Lucent 7750 SR do to support VPLS services for different customers?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 143
Consider a network that has four PE routers. If a customer wants a VPLS that has sites on only three of the
PEs, how many mesh SDPs need to be configured for this service?
A. 3
B. 4
C. 6
D. 12
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 144
Which of the following about an E-pipe terminating on a VPLS is FALSE?
A. The VC-IDs used between the E-pipe and VPLS must match.
B. The E-pipe must maintain a MAC FDB in order to connect to the VPLS.
C. The service ID of the E-pipe can be different from that of the VPLS.
D. The service MTU of the VPLS and E-pipe must match.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 145
Which of the following best describes how a MAC FDB is populated in a VPLS service?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 146
Which of the following best describes the flooding of traffic on a PE when unknown traffic is received on a
SAP of a VPLS?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 147
Click the exhibit.
Both clips of output are from router R4. The show service command indicates that an SDP is down. What
might be the cause?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 148
How many service labels must be signaled to bring up a fully-meshed VPLS among five PE routers?
A. 1
B. 5
C. 10
D. 20
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 149
Click the exhibit.
A. ping
B. Isp-ping
C. traceroute
D. Isp-trace
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 150
Click the exhibit.
The operator at PE1 wants to analyze the traffic between PE2 and CE4. On an Alcatel-Lucent 7750 SR,
which of the following is required as part of the configuration?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 151
Click the exhibit.
A. vprn-ping
B. sdp-ping
C. traceroute
D. Isp-trace
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 152
Click the exhibit.
PE1 and PE2 are Alcatel-Lucent 7750 SRs. What needs to be added to PE1's configuration to mirror traffic
between PE2 and the customer site?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 153
Click the exhibit.
E-pipe 100 is using an SDP with an LSP that uses the path shown (PE1-PE2-PE3-PE4). Based on the
OAM command output, which of the following is FALSE?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 154
Which one of the following items CANNOT be used as a mirror source on an Alcatel-Lucent 7750 SR?
A. IP filter
B. MAC filter
C. Egress label
D. Ingress label
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 155
Which of the following about the Alcatel-Lucent 7750 SR's sdp-ping utility is FALSE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 156
What is the minimum Ethernet physical network MTU required for a Layer 2 service on an MPLS
encapsulated SDP with a service MTU of 1500?
A. 1500
B. 1508
C. 1514
D. 1522
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 157
On an Alcatel-Lucent 7750 SR, the OAM command 'svc-ping' can be used with options bcal-sdp' and
'remote-sdp'. Which of the following is TRUE?
A. iocal-sdp' and 'remote-sdp' indicate that all services using these SDPs are pinged.
B. 'Iocal-sdp' and remote-sdp' indicate that pings are initiated from both local and remote routers.
C. Both 'Iocal-sdp' and 'remote-sdp' take parameters to specify which SDPs are used for the test.
D. 'Iocal-sdp' indicates that the ping is sent in-band, and remote-sdp' indicates the return ping is in-band.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 158
Which of the following about the VPRN data plane is TRUE?
A. A packet receives a service label and a transport label at the ingress PE.
B. A packet has its service label swapped at each P router.
C. The egress PE pops the service label, and the transport label is forwarded.
D. The service label is popped by the remote CE.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 159
Which of the following about route distinguishes on the Alcatel-Lucent 7750 SR is TRUE?
A. Route distinguishes are used to ensure that VPRN IP prefixes are globally unique.
B. Route distinguishes are appended to IPv4 prefixes to form IPv6 prefixes.
C. Route distinguishes are used to determine which routes a VPRN should import.
D. CE routes use a route distinguisher to indicate which VPRN they are associated to.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
corrected and valid.
QUESTION 160
Click the exhibit.
Based on the output from PE router R1 about VPRN 100, by which protocol was 192.168.10.0/24 learned?
A. BGP
B. MP-BGP
C. LDP
D. MPLS
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Topic 4, Volume D
QUESTION 161
Which of the following about VPRN route targets is FALSE?
A. They are used to identify the VRF table for a prefix at the receiving PE.
B. They are used by VPRNs to control the distribution of VPN routing information.
C. They are distributed to all PEs and CEs that are part of the VPRN.
D. They are distributed to PEs to identify the VRF table that a VPN-IPv4 prefix is associated with.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 162
On an Alcatel-Lucent 7750 SR, which of the following about IES interfaces is FALSE?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 163
Click the exhibit.
Part of a 6VPE deployment is shown in this exhibit. Which of the following is the correct configuration and
context on PE1 for a BGP peering session with CE1?
A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 164
Click the exhibit.
This output is from a router that is part of a 6VPE deployment using a VPRN. Which type of router would
this configuration be found on?
A. A CE router.
B. A P router.
C. A PE router.
D. Both P and PE routers.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 165
On an Alcatel-Lucent 7750 SR, why must the MTU be explicitly set when configuring an IES spoke
termination to a VPLS?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 166
Click the exhibit.
Assuming CE1 exports its system address using BGP, is a routing policy required on PE1 to advertise
CE1's system address to PE2?
A. Yes, A routing policy is required to advertise routes between PE routers in a VPRN regardless of the
CE-PE routing.
B. Yes, A routing policy is required in this case because BGP is used as the PE-CE routing protocol.
C. No, a routing policy is not required. By default, the Alcatel-Lucent 7750 SR will advertise all VPRN
routes between PE routers.
D. No, a routing policy is not required on PE1, but an import policy is required on PE2.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 167
Which of the following about IES is FALSE?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 168
When using MP-BGP for an IPv4 VPRN service, what address family needs to be used for a PE- CE BGP
session?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 169
On the Alcatel-Lucent 7750 SR, which of the following statements about MP-BGP used for a VPRN is
TRUE?
A. Routes from different customers with the same IPv4 address prefix are treated as equivalent by MP-
BGP.
B. MP-BGP will advertise routes to other BGP sessions on the same PE without the need of policies.
C. The multi-protocol nature of MP-BGP allows VPRN routes to be converted into IPv4 routes in the
provider core network.
D. MP-BGP is an enhanced version of BGP that can carry customer route prefixes for multiple VPRNs.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 170
Click the exhibit.
R1 and R4 are providing a VPRN for the CEs. Which of the following about the traceroute run on router R5
is TRUE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 171
Which of the following about VPRN labels is FALSE?
A. The outer label allows traffic to transit across the MPLS network.
B. The inner label identifies the VPRN service.
C. MP-BGP is used to signal VPRN labels.
D. The VPRN service label contains the customer's IP address.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 172
Which of the following about VPRNs is FALSE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 173
Click the exhibit.
The output is from PE router R1 about VPRN service 100. From which protocol did router R1 learn the
prefix 192.168.20.0/24?
A. LDP
B. BGP
C. MP-BGP
D. MPLS
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 174
Which of the following about 6VPE is FALSE?
A. To advertise VPN-IPv4 and VPN-IFV6 routes, two MP-BGP sessions are required.
B. PE routers must support both IPv4 and IPv6 addresses; customer routers can use either one.
C. MP-BGP is used to advertise IPv6 prefixes and the associated VPRN labels.
D. The provider core routers are IPv6-unaware.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 175
Which of the following about VPRN VRF tables is FALSE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 176
Which protocol can be used to signal the outer label for a VPN service?
A. IPCP
B. LDP
C. PPP
D. TLDP
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 177
Which of the following about SDPs is TRUE?
Explanation/Reference:
QUESTION 178
Which of the following is TRUE when a service uses a GRE transport tunnel?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 179
Which of the following fields is NOT present in a GRE encapsulated VPN service packet?
A. DLC Header
B. Control Word
C. Transport Label
D. Service Label
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 180
Which of the following about dot1Q SAPs is FALSE?
A. The dot1Q default SAP (port: *) can be used to pass VLAN tags transparently through a network.
B. The dot1Q null SAP (port: 0) accepts all tagged frames and untagged frames.
C. The dot1Q default SAP (port: *) accepts all untagged frames and any frames with tag values that are
not used as a service-delimiting value on another SAP.
D. A dot1q null SAP (port: 0) and a dot1q default SAP (port: *) cannot both be defined on the same port.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 181
Consider an E-pipe service configured with SAP 1/1/1:5 and SAP 1/1/1:6.7. If the SAP 1/1/1:5 accepts an
ingress frame, which of the following is TRUE?
A. The frame egresses 1/1/1:6.7 with an outer VLAN tag of 6 and inner tag of 7.
B. The frame is dropped at the egress SAP 1/1/1:6.7.
C. The frame egresses 1/1/1:6.7 with VLAN tag 5.
D. The frame egresses 1/1/1:6.7 with VLAN tag 6.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 182
On which component is vc-type configured to create an E-pipe service that preserves the VLAN tag during
transport?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 183
On an Alcatel-Lucent 7750 SR, which vc-type will forward service delimiting tags at the ingress PE?
A. vc-type ether
B. vc-type vlan
C. vc-type dot1q
D. vc-type null
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 184
Which of the following about F-pipes is FALSE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 185
Which of the following SAPs will NOT forward untagged frames?
A. sap 1/1/1
B. sap 1/1/1:*
C. sap 1/1/1:0
D. sap 1/1/1:1
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 186
The SAP 1/1/1:2.3 receives an Ethernet frame with outer VLAN tag 5 and inner VLAN tag 3.
Which of the following is TRUE?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 187
Click the exhibit. This output is from router R4. Service 333 is a VPLS. Why might the peer 10.10.10.1 have
the same value for IngLbl and EgrLbl?
A. The labels are of local significance only, so other routers can use the same value.
B. 10.10.10.1 has yet to send its own unique label.
C. Router R4 is using the same tunnel to send and receive to 10.10.10.1.
D. The service on 10.10.10.1 is down, so it is rejecting packets.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
http://www.gratisexam.com/
QUESTION 188
A customer has sites on three different Alcatel-Lucent 7750 SRs. The customer requires a fully- meshed
VPLS. Which of the following is TRUE?
Explanation/Reference:
QUESTION 189
Which of the following about Hierarchical VPLS is FALSE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 190
By default, what does the Alcatel-Lucent 7750 SR do when a frame with an unknown destination address is
received in a VPLS?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 191
On an Alcatel-Lucent 7750 SR, which of the following about a VPLS is FALSE?
A. By default, the VC ID on the mesh SDPs of a VPLS are set to the service ID.
B. A VPLS appears to the customer as a direct Ethernet connection.
C. Mesh SDPs are used for VPLSes to avoid loops.
D. By default, T-LDP is used for signaling service labels.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 192
Click the exhibit.
E-pipe 100 is using an SDP (4) with an LSP that uses the path shown (PE1-PE2-PE3-PE4). Which of the
following is the expected output from the OAM command?
A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 193
Click the exhibit.
PE1 and PE2 are Alcatel-Lucent 7750 SRs. Which of the following is the missing configuration required on
PE2 to complete the mirror?
A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 194
Click the exhibit.
A. mac-trace
B. svc-ping
C. Isp-trace
D. traceroute
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 195
Click the exhibit.
An operator at PE1 wants to analyze the traffic between CE1 and PE1 on SAP 1/1/3, On an Alcatel-Lucent
7750 SR, which of the following is NOT required as part of the configuration?
A. A mirror source with a defined source type.
B. A mirror source defined with an SDP destination.
C. A mirror destination with a SAP defined.
D. A mirror destination and a mirror source with the same service ID.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 196
Which of the following about the label stack of a VPRN is FALSE?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 197
Which of the following about IES is FALSE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 198
Click the exhibit.
This output is from PE router R1. Based on the output about VPRN 100, how many prefixes has router R1
learned from CE router R5?
A. 0
B. 2
C. 3
D. 6
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 199
Which of the following is a benefit of VPRN as compared to VPLS?
A. Service providers can apply QoS, ingress/egress traffic shaping and policing on a per service basis.
B. Different customers with overlapping address space can be accommodated.
C. There is a clear demarcation of customer and service provider networks.
D. Customers can connect to the same service using different subnets.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 200
Which of the following about VPRN route targets is FALSE?
Explanation/Reference:
QUESTION 201
A CE is connected to an IES interface. Which of the following is TRUE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 202
Which of the following about VPRN VRF tables is FALSE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 203
Which of the following about route distinguishes on the Alcatel-Lucent 7750 SR is FALSE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 204
Which of the following about the VPN-IFV4 address family is FALSE?
Explanation/Reference:
QUESTION 205
An IPv4 MPLS provider network is being configured for 6VPE. BGP is being used for the PE- CE protocol to
exchange IPv6 routes. Which of the following is FALSE?
A. MP-BGP in the provider network needs to support the VPN-IPv6 address family.
B. PE routers must be configured to run MP-BGP.
C. PE-to-CE BGP sessions need to be configured to support IPv6.
D. The provider network core must be configured to support IPv6.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 206
On an Alcatel-Lucent 7750 SR, which of the following statements about the default advertisement of VRF
routes is true?
A. All routes in the VRF are advertised to the PEs and CEs.
B. No routes in the VRF are advertised to the PEs or to the CEs.
C. All routes in the VRF are advertised to the PEs, but not to the CEs.
D. All routes in the VRF are advertised to the CEs, but not to the PEs.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 207
The SAP 1/1/1:2.3 receives an Ethernet frame with outer VLAN tag 2 and inner VLAN tag 5.
Which of the following is TRUE?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 208
Which of the following SAPs can be used so that only untagged frames and frames with a VLAN tag of 0
are accepted?
A. sap 1/1/1:0
B. requires both sap 1/1/1:0 and sap 1/1/1:*
C. sap 1/1/1:0-4096
D. sap 1/1/1:*
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 209
Which of the following SAPs will forward all tagged and untagged frames on the port?
A. sap 1/1/1
B. sap 1/1/1:*.0
C. sap 1/1/1:0.*
D. 1/1/1:0
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 210
An SDP using MPLS encapsulation is configured for an E-pipe service. The network port on the Alcatel-
Lucent 7750 SR used by the SDP has an MTU of 8000. What is the SDP path MTU?
A. 7958
B. 7978
C. 8022
D. 8042
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 211
Which of the following about configuring a distributed E-pipe service is TRUE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 212
Which of the following best describes a MAC FDB used by a VPLS service?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 213
Which of the following about the Alcatel-Lucent 7750 SR svc-ping, when used in-band, is FALSE?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 214
What is the minimum Ethernet physical network MTU required for a Layer 2 service on an MPLS
encapsulated SDP with a service MTU of 1518?
A. 1520
B. 1540
C. 1548
D. 1556
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 215
Which one of the following commands on an Alcatel-Lucent 7750 SR can take a FEC as a parameter to
verify if a packet for that FEC reaches the appropriate LER?
A. ping
B. sdp-ping
C. svc-ping
D. Isp-ping
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 216
Which of the following regarding 6VPE is FALSE?
A. 6VPE is a tunneling technology that makes use of MPLS tunnels to transport IPv6 prefixes over an IPv4
infrastructure.
B. Customers connected to 6VPE can run IPv6 or IPv4.
C. On a PE router, if the MP-BGP next hop is an IPv4 address, a mapped IPv6-compliant address will be
used.
D. 6VPE implements its own VPN-IPv6 address family and is a replacement for MP-BGP.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 217
Click the exhibit.
Routes are exchanged between CE1 and PE1 using BGP. CE2 and PE2 use static routes to forward traffic
to and from the VPRN. Which of the following is FALSE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 218
Which of the following about IES is TRUE?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 219
Which of the following about the BGP VPN-IPv4 address family is FALSE?
A. When a PE router receives an IPv4 prefix from its local CE, it creates a VPN-IFV4 prefix.
B. VPN-IPv4 allows BGP to distinguish between duplicate prefixes originating from different customers.
C. In a VPRN, data traffic is carried in packets that have VPN-IPv4 addresses.
D. VPN-IFV4 addresses are only present within the service provider network.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 220
On the Alcatel-Lucent 7750 SR, which one of the following steps is NOT required when enabling an MP-
BGP session between PE routers in a VPRN?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 221
A CE is connected to an IES interface. Which of the following is TRUE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 222
Which of the following about VPRN route targets is FALSE?
Explanation/Reference:
QUESTION 223
Which of the following about the components of a distributed service on the Alcatel-Lucent 7750 SR is
TRUE?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 224
Click the exhibit.
Which of the following statements about the E-pipe service is TRUE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 225
Which of the following about transport and service tunnels is FALSE?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 226
In a Layer 2 encapsulation using T-LDP, what does the second (bottom) label represent?
A. Tunnel Label
B. VC Label
C. Operational Control Word
D. VPI
E. VCI
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 227
Which of the following statements about SAPs that are part of a VPVVS is FALSE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 228
Which of the following about SAPs is TRUE?
A. More than one SAP can be configured on a physical port that is configured for null encapsulation.
B. Dot1Q Ethernet encapsulated access ports can support multiple SAPs and services.
C. SAPs can be created on ports designated as "Network".
D. SAPs can only be created on Ethernet ports.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 229
An E-pipe is configured with a service MTU of 5000. What is the minimum MTU value that should be set on
an access port for a dot1q encapsulated SAP on this service?
A. 5000
B. 5004
C. 5008
D. 5014
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 230
Which of the following about VPLS MAC learning is FALSE?
A. The PE routers of the service are responsible for learning MAC addresses.
B. Flooding ensures that all PEs in a fully-meshed VPLS will learn the source address of all traffic.
C. MAC learning reduces flooding of frames with previously learned addresses.
D. Multiple VPLSes on the same PE share the same MAC FDB.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 231
By default, how does a VPLS handle a tagged frame received at the ingress of a null SAP on an Alcatel-
Lucent 7750 SR?
A. The FCS is verified and kept in the customer frame. The VLAN tag is kept and transported over the
network.
B. The FCS is verified and kept in the customer frame. The VLAN tag is removed for transport over the
network.
C. The FCS is verified and removed from the frame. The VLAN tag is kept and transported over the
network.
D. The FCS is verified and removed from the frame. The VLAN tag is removed for transport over the
network.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 232
Click the exhibit.
This is output from router R4. Service 333 is a VPLS. Why does peer 10.10.10.1 not have an EgrLbl?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 233
How many service labels must be signaled to bring up a fully-meshed VPLS among three PE routers?
A. 1
B. 3
C. 6
D. 12
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 234
Which of the following is NOT a benefit of "Hub and Spoke'' VPLS deployments?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 235
Which utility on the Alcatel-Lucent 7750 SR can be used to investigate an MPLS path?
A. Isp-trace
B. Idp-trace
C. Sdp-ping
D. Svc-ping
E. Ping
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 236
If the Alcatel-Lucent 7750 SR is rebooted after an "admin save'' has been performed, which of the following
about mirror services is TRUE?
Explanation/Reference:
QUESTION 237
Click the exhibit.
This PE is connected to an IPv4 core and is being configured to support 6VPE for a VPRN. Which of the
following completes this section of the configuration?
A. Family ipv4
B. Family ipv6
C. Family ipv4 ipv6
D. Family vpn-ipv4
E. Family vpn-ipv4 vpn-ipv6
Correct Answer: E
Section: (none)
Explanation
Explanation/Reference:
QUESTION 238
Click the exhibit button.
Part of a 6VPE deployment is shown. Which of the following is the correct configuration and context on
router CE1 for a BGP peering session with 6VPE1?
A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 239
Click the exhibit.
The output is from PE router R4 about VPRN service 100. How many prefixes have been learned from the
MP-BGP protocol?
A. 0
B. 2
C. 3
D. 6
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 240
On an Alcatel-Lucent 7750 SR, what is the recommended approach for making sure that MTUs between a
VPLS and its spoke IES termination match?
A. Set the service MTU of the VPLS to match the IES MTU.
B. Set the ip-mtu of the IES to match the service MTU of the VPLS.
C. Set the SDP MTU of the IES to match the SDP MTU of the VPLS.
D. Set the MTU of the IES's network port to match the service MTU of the VPLS.
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 241
Which of the following about SAPs is FALSE?
A. A SAP can be associated with more than one service.
B. A SAP is the subscriber's point of entry to the service network.
C. A SAP is created by specifying a physical port and an encapsulation type.
D. A SAP can only be created on a port configured as "access".
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 242
In a Layer 2 encapsulation using T-LDP, what does the first (top) label represent?
A. Tunnel Label
B. VC Label
C. Operational Control Word
D. UNI
E. NNI
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 243
When configuring distributed services across a network, it is considered best practice to configure which of
the following parameters as globally significant?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 244
On an Alcatel-Lucent 7750 SR, which vc-type will strip service delimiting tags at the ingress PE?
A. vc-type ether
B. vc-type vlan
C. vc-type dotlq
D. vc-type null
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 245
What happens by default on an Alcatel-Lucent 7750 SR when a null encapsulated SAP receives a frame
with a VLAN tag?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 246
Which of the following about ADSPEC is FALSE?
A. ADSPEC sets an SDP's MTU to the smallest MTU value found along the LSP path.
B. RSVP must be enabled on all MPLS routers of a path to use ADSPEC.
C. ADSPEC can automatically adjust the service MTU.
D. ADSPEC can be enabled on individual LSPs.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 247
Which of the following is a characteristic of a VPLS?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 248
Click the exhibit.
The CEs use BGP and export policies to advertise their local prefixes with the VPRN on their PEs. If the
VPRN is functioning properly, which of the following commands will succeed when performed on router R1?
A. "ping 192.168.20.1"
B. "oam vprn-ping 100 source 192.168.10.1 destination 192.168.20.1"
C. "oam vprn-ping 100 source 192.168.20.1 destination 192.168.10.1"
D. "ping 10.10.10.6" (router R6's system IP)
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 249
Which of the following about VPN labels is FALSE?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 250
Click the exhibit.
Based on this output from PE router R1, how many other PEs are participating in the VPRN?
A. 0
B. 1
C. 2
D. 3
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 251
Click the exhibit.
The output is from PE router R1 about VPRN service 100. From which protocol did router R1 learn the
prefix 192.168.20.0/24?
A. LDP
B. BGP
C. MP-BGP
D. MPLS
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 252
Which of the following about VPRN VRF tables is FALSE?
A. A PE uses the same VRF table for all the VPRN services on it.
B. A PE uses a VRF to maintain forwarding information.
C. Information for VRFs can be advertised between PEs by MP-BGP.
D. A PE uses a VRF to route traffic to CEs.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
answer is updated.
QUESTION 253
Which of the following about SDPs is FALSE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 254
Which of the following about VPLS MAC learning is TRUE?
A. Mesh SDPs assist MAC learning by flooding traffic to other mesh SDPs.
B. A PE keeps a single FDB for all VPLSes it has.
C. Frames received on a SAP that are broadcast, multicast or unknown are flooded.
D. The FDB only stores the MAC addresses of remote sites.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 255
A network consists of four PE routers. A customer requires a VPLS and has sites connected to each PE.
The VPLS is fully meshed using IP/MPLS. How many SDPs must be configured on each PE?
A. 3
B. 4
C. 6
D. 8
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 256
What happens by default on an Alcatel-Lucent 7750 SR when a VPLS accepts a tagged frame at the
ingress SAP 1/1/1:100?
A. The FCS is verified and kept in the customer frame. The VLAN tag is kept and transported over the
network.
B. The FCS is verified and kept in the customer frame. The VLAN tag is removed for transport over the
network.
C. The FCS is verified and removed from the frame. The VLAN tag is kept for transport over the network.
D. The FCS is verified and removed from the frame. The VLAN tag is removed for transport over the
network.
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 257
What Alcatel-Lucent 7750 SR OAM tool can be used to verify the end-to-end connectivity of a service?
A. Sdp-ping
B. Isp-ping
C. Svc-ping
D. Sdp-mtu
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 258
A VPLS has a service MTU of 1600. To create an IES spoke termination to the VPLS, what ip- mtu value
must be used for the IES?
A. 1586
B. 1596
C. 1600
D. 1614
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 259
On which object is ADSPEC enabled?
A. SDP
B. Network port
C. LSP
D. Service
E. RSVP
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 260
An SDP using GRE encapsulation is configured for an E-pipe service. The network port used by the SDP
has an MTU of 8000. What value does the SDP path MTU have by default on an Alcatel-Lucent 7750 SR?
A. 7958
B. 7978
C. 8022
D. 8042
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 261
A VPLS receives a frame with the single VLAN tag 35 on the Q-in-Q SAP 1/1/1:35.*. Which of the following
describes default Alcatel-Lucent 7750 SR behavior?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 262
Which of the following about the Isp-ping command on the Alcatel-Lucent 7750 SR is FALSE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 263
Click the exhibit.
The operator at PE1 wants to analyze the traffic between CE4 and PE2. On an Alcatel-Lucent 7750 SR,
which of the following is required as part of the configuration?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 264
Which of the following about route distinguishes on the Alcatel-Lucent 7750 SR is TRUE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 265
Which of the following about VPRNs is TRUE?
A. Customers must use the same routing protocol as the service provider.
B. Customers belonging to the same VPRN service must use the same subnet.
C. Service providers only need to perform configurations on the PEs to add additional VPRNs.
D. For each VPRN, only one customer can be connected at each PE.
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 266
Click the exhibit.
The two PEs are providing 6VPE and IPv4 VPRNs. The core network is IPv4/MPLS. Which of the following
is the BGP family configuration for the MP-BPG on the PEs?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 267
Which of the following comparisons between E-pipes and VPLSes is FALSE?
A. They both function as a Layer 2 switch from the service provider's perspective.
B. They both support SAP encapsulations of null, dot1Q and Q-in-Q.
C. They both use SAPs as the demarcation point between the customer and the provider.
D. MAC addresses are learned by VPLSes, but not by E-pipes.
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 268
Which of the following about the Alcatel-Lucent 7750 SR sdp-ping is TRUE?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 269
VPWS allows carriers to offer services such as point-to-point frame-relay, ATM, and Ethernet on a single
platform without the need for multiple overlay networks.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 270
Which of the following best describes a VPLS?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 271
Which of the following is NOT a VPWS service supported on the Alcatel-Lucent 7750 SR?
A. Epipe
B. Fpipe
C. Apipe
D. Ipipe
E. Cpipe
F. Gpipe
Correct Answer: F
Section: (none)
Explanation
Explanation/Reference:
QUESTION 272
A service can be either local or distributed.
A. TRUE
B. FALSE
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 273
When configuring distributed services across a network, it is considered best practice to configure which of
the following parameters as globally significant? (Choose 2)
A. SDP ID
B. Service ID
C. Customer ID
D. SAP ID
Correct Answer: BC
Section: (none)
Explanation
Explanation/Reference:
QUESTION 274
When a physical port is configured for null encapsulation, many SAPs can be configured using that port.
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 275
Which of the following statements is FALSE regarding SAPs?
Explanation/Reference:
QUESTION 276
SAPs in an Epipe service can only be configured on Ethernet ports
A. TRUE
B. FALSE
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 277
Which of the following commands is used to configure the encapsulation type of an Ethernet port?
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 278
Which of the following best describes a distributed Epipe Service?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 279
Which of the following options are used to configure an MPLS signaling type to be used on an SDP?
(Choose 2)
Correct Answer: CD
Section: (none)
Explanation
Explanation/Reference:
QUESTION 280
Which of the following encapsulation types on an Ethernet port support the provisioning of multiple SAPs?
(Choose 2)
A. Dot1Q
B. Q-in-Q
C. ATM
D. NULL
E. Nil
Correct Answer: AB
Section: (none)
Explanation
Explanation/Reference:
QUESTION 281
Which tree in the CLI would you need to be in to add a QoS policy to a SAP?
A. config>router#
B. config>qos#
C. config>port#
D. config>service#
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 282
Which of the following commands is used to disable an Epipe service?
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
corrected and modified.
QUESTION 283
Which of the following commands is required to configure an Ethernet port to be used as a SAP in a
service?
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 284
Which of the following tasks must be carried out before deleting an Epipe service? (Choose 4)
Explanation/Reference:
QUESTION 285
Which of the following SAPs will forward all tagged and untagged frames on the port? (Choose
2)
A. sap 1/1/1
B. sap 1/1/1:*
C. sap 1/1/1:*.0
D. sap 1/1/1:0*
E. sap 1/1/1:0
Correct Answer: AB
Section: (none)
Explanation
Explanation/Reference:
QUESTION 286
A customer requests that their Layer 2 Ethernet service be configured to forward frames up to 9000 bytes.
The service provider is using MPLS encapsulation. What is the minimum MTU setting for the network
ports?
A. 9000
B. 9004
C. 9008
D. 9022
E. 9036
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 287
FRF.5 is a standard that describes which of the following requirements?
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
QUESTION 288
Which of the following statements are TRUE regarding a fully meshed VPLS service with a default setting?
(Choose 3)
Explanation/Reference:
http://www.gratisexam.com/