Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
** ON A/C ALL
TASK 32-41-11-400-006-A
Installation of the MLG Wheel
WARNING: YOU MUST NOT PUT TOO MUCH GREASE ON THE AXLE SLEEVE. A VERY
HOT BRAKE CAN CAUSE THE GREASE TO BURN AND CAUSE A FIRE.
REFERENCE QTYDESIGNATION
No specific AR TROLLEY - WHEEL CHANGE, A/C
** ON A/C 101-200
No specific Torque wrench: range to between 0.28 and 0.34 m.daN
(24.78 and 30.09 lbf.in)
** ON A/C ALL
No specific Torque wrench: range to between 0.4 and 0.45 m.daN
(35.40 and 39.82 lbf.in)
No specific Torque wrench: range to between 1.6 and 1.9 m.daN
(11.80 and 14.01 lbf.ft)
** ON A/C 101-200
No specific Torque wrench: range to between 3.1 and 3.4 m.daN
(22.86 and 25.07 lbf.ft)
No specific Torque wrench: range to between 5 and 10 m.daN
(36.87 and 73.75 lbf.ft)
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 1 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
REFERENCE QTYDESIGNATION
No specific Torque wrench: range to between 15 and 19 m.daN
(110.62 and 140.12 lbf.ft)
No specific Torque wrench: range to between 25 and 30 m.daN
(184.37 and 221.24 lbf.ft)
(H47682) 1 ADAPTOR-MLG
** ON A/C ALL
(MG174-04) 1 DISASSEMBLY TOOL
B. Consumable Materials
REFERENCE DESIGNATION
(Material No. 03GBB1) Synthetic Oil base Grease-General Purpose Clay
Thickened -
(Material No. 03GBC1) Synthetic Oil base Grease-General Purpose Lithium
Thickened Low Temp. -
(Material No. 03GCB1) Synthetic Oil base Grease-Landing Gear Wheel Bearing
Lithium Thickened -
(Material No. 03HBD9) Synthetic Ester base Grease-General Purpose Low Temp
-
(Material No. 03LBB1) Grease-Thread Anti-seize Graphited and Petrolatum -
(Material No. 08BBB1) Non Aqueous Cleaner-- Petroleum Based -
No specific LOCTITE 243 - ADHESIVE (Material No. 08-720)
No specific corrosion resistant steel lockwire dia 0.8 mm (0.03 in.)
D. Expendable Parts
** ON A/C 101-200
4 cotter pins 32-11-13-01-200
5 nuts 32-11-13-01-210
4 cotter pins 32-11-13-03-200
5 nuts 32-11-13-03-210
4 cotter pins 32-11-85-61-200
5 nuts 32-11-85-61-210
14 tab-washers 32-48-51-04-035
** ON A/C ALL
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 2 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
E. Referenced Information
REFERENCE DESIGNATION
(Ref. 07-12-00-582-002-A). Jacking of the Main Landing Gear
(Ref. 12-14-32-614-001-A). Nitrogen Filling of the Tires
(Ref. 29-10-00-863-002-A). Pressurize the Yellow Hydraulic System with a Hydraulic
Ground Power-Cart
(Ref. 29-24-00-863-001-A). Pressurize the Yellow Hydraulic System with the Electric
Pump
(Ref. 32-00-00-081-001-A). Removal of the Safety Devices from the Landing Gears
(Ref. 32-00-00-481-001-A). Installation of the Safety Devices on the Landing Gears
(Ref. 32-41-00-210-003-A). Functional Check of Tire Pressures
(Ref. 32-41-00-910-001-A). Tire Mixability Precautions
(Ref. 32-42-27-000-001-A). Removal of the Brake
(Ref. 32-42-27-210-006-A). Inspection/Check of the Brake with the Wheel Removed
(Ref. 32-42-27-400-001-A). Installation of the Brake
(Ref. 32-48-00-720-001-A). Functional Test of the Brake Fans
(Ref. 12-22-00-00). LUBRICATION - DESCRIPTION AND OPERATION
** ON A/C 101-161
Main Gear Wheel SHEET 1
** ON A/C 162-200
Main Gear Wheel SHEET 1
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 3 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
2650GM
A 2649GM
A
1 2 3 4 5
A
A
2652GM
2651GM
6
7 A
8
EXAMPLE
9
10
11
12
13
22 21 8 4 5 6 20 23 11
14
15
19
18
17
16
N_MM_324111_4_UBH2_01_03
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 4 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
B
A 2649GM
(2652GM)
2 2651GM
1
3 (2650GM)
A
4 LH SHOWN
RH SYMMETRICAL
5
6
7
8 9
10
11
12
21
22 8 6 13
4 5 20
23
11
19
18
14
15
B
TYPICAL OR
17 16
14
15
N_MM_324111_4_UBH0_01_03
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 5 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
3. Job Set-up
Subtask 32-41-11-941-097-A
A. Safety Precautions
(1) Make sure that the warning notice is in position in the cockpit to tell persons not to
operate the landing gear.
(2) Make sure that the wheel chocks are in position.
(3) Make sure that the safety devices are installed on the landing gear
(Ref. AMM TASK 32-00-00-481-001) .
Subtask 32-41-11-865-115-A
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
NOTE: On the right center instrument panel 400VU, make sure that the brake
pressure indication on the Yellow brake-pressure triple indicator is correct.
If necessary pressurize the brake accumulator with the Yellow pump
(Ref. AMM TASK 29-10-00-863-002) or (Ref. AMM TASK 29-24-00-863-
001) .
4. Procedure
** ON A/C 101-161
** ON A/C 162-200
(Ref. Fig. Main Gear Wheel SHEET 1)
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 6 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
** ON A/C ALL
NOTE: If the wheel has a pressure-sensor seal cap, make sure that the seal cap is
correctly installed and safetied with a nut and a cotter pin.
NOTE: Because of the aircraft configuration, the installation of the Tire Pressure Indicating
System (TPIS) balance weight changes: If the aircraft has the TPIS and the
Brake Cooling Fan (BCF)/Universal Brake Cooling Fan (UBCF), no TPIS balance
weight is installed on the wheel rim. The balance weight is part of the BCF/
UBCF assembly (brake-fan shroud support), refer to the BCF/UBCF Component
Maintenance Manual (CMM). If the aircraft has the TPIS only (no BCF/UBCF): *
On the A321 aircraft, you must install the TPIS balance weight on the wheel rim,
refer to the wheel CMM. * On the A318-A319-A320 aircraft, you must install the
TPIS balance weight on the hubcap, refer to the hubcap CMM. If the aircraft has no
TPIS, no TPIS balance weight is necessary.
Subtask 32-41-11-210-075-A
A. Tires of Different Type
(1) Obey the tire mixability precautions (Ref. AMM TASK 32-41-00-910-001) .
** ON A/C 101-200
CAUTION: MAKE SURE THAT THE GREASE USED FOR THE AXLE SLEEVE
IS THE SAME AS THE GREASE USED FOR THE BEARINGS (CONE
AND CAGE). IF YOU USE A DIFFERENT GREASE, YOU CAN CAUSE
DAMAGE TO THE BEARINGS.
(1) Make sure (if the tire mixability is not permitted) that the wheel for installation has
the same type of tire (radial or cross-ply) as the other wheel on the MLG.
(2) Make sure that the parts retained from the removed component are clean and in
the correct condition.
(3) Clean the component interfaces and the adjacent area.
(4) Do an inspection of the component interfaces and the adjacent area.
(a) Examine the locking holes and the adjacent areas carefully.
(5) Remove brake dust.
(6) Do an inspection of the brake with the wheel removed (Ref. AMM TASK 32-42-
27-210-006) .
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 7 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
NOTE: If the brake is unserviceable it must be replaced (Ref. AMM TASK 32-42-
27-000-001) and (Ref. AMM TASK 32-42-27-400-001) .
(7) Make sure that the driving keys on the brake rotors are correctly aligned.
(8) Make sure that the splines (21) of the tachometer drive shaft and the splines of the
bushing (17) are in the correct condition.
(9) Clean the axle sleeve (2) with Non Aqueous Cleaner-- Petroleum Based
- (Material No. 08BBB1) and dry it with filtered compressed air.
(10) Do a visual inspection of the axle protective sleeve to make sure that it is in correct
condition.
(11) If damage is found, refer to CMM or contact MEGGIT for allowable tolerance.
(12) Make sure that the retaining ring (3) of the axle sleeve (2) is in the correct position.
The ring must be correctly engaged in its groove. If not, the axle sleeve is not
installed correctly and you can damage it when you install the axle nut.
(13) Clean the splines of the bushing (17), the splines (21) of the tachometer drive
shaft and the splines (22) of the impeller drive shaft with Non Aqueous Cleaner--
Petroleum Based - (Material No. 08BBB1) and dry with filtered compressed air.
(14) Apply a thin layer of Grease-Thread Anti-seize Graphited and Petrolatum
- (Material No. 03LBB1) on the splines of the bushing (17), the splines (21) of the
tachometer drive shaft and the splines (22) of the impeller drive shaft.
WARNING:YOU MUST NOT PUT TOO MUCH GREASE ON THE AXLE SLEEVE. A
VERY HOT BRAKE CAN CAUSE THE GREASE TO BURN AND CAUSE
A FIRE.
(15) Apply a thin layer of Synthetic Ester base Grease-General Purpose Low Temp
- (Material No. 03HBD9) or Synthetic Oil base Grease-General Purpose Clay
Thickened - (Material No. 03GBB1) or Synthetic Oil base Grease-Landing Gear
Wheel Bearing Lithium Thickened - (Material No. 03GCB1) or Synthetic Oil base
Grease-General Purpose Lithium Thickened Low Temp. - (Material No. 03GBC1)
to the load-bearing surface of the axle nut.
(16) Apply a thin layer of Synthetic Ester base Grease-General Purpose Low Temp
- (Material No. 03HBD9) or Synthetic Oil base Grease-General Purpose Clay
Thickened - (Material No. 03GBB1) or Synthetic Oil base Grease-Landing Gear
Wheel Bearing Lithium Thickened - (Material No. 03GCB1) or Synthetic Oil base
Grease-General Purpose Lithium Thickened Low Temp. - (Material No. 03GBC1)
to the axle sleeve (2).
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 8 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
(17) Clean the inner surface of the wheel bearings (surface that touches the axle). Do
not apply grease on these surfaces.
Subtask 32-41-11-420-081-T
C. Installation of the Wheel
(1) Use the TROLLEY - WHEEL CHANGE, A/C to align the wheel (1) with the driving
keys on the brake rotors.
(2) Push the wheel (1) fully on the axle.
(3) Remove the PROTECTOR (F46754-1000) .
(4) Apply Synthetic Ester base Grease-General Purpose Low Temp
- (Material No. 03HBD9) or Synthetic Oil base Grease-General Purpose Clay
Thickened - (Material No. 03GBB1) or Synthetic Oil base Grease-Landing Gear
Wheel Bearing Lithium Thickened - (Material No. 03GCB1) or Synthetic Oil base
Grease-General Purpose Lithium Thickened Low Temp. - (Material No. 03GBC1)
to the threads of the axle.
(5) Install the axle nut (7) on the axle and tighten it with the ADAPTOR-
MLG (H47682) .
(6) In the cockpit, set the PARK BRK control switch to OFF.
(7) TORQUE the axle nut (7) to between 25 and 30 m.daN
(184.37 and 221.24 lbf.ft) while you turn the wheel in the same direction.
(8) Make sure that the wheel does not turn and loosen the axle nut (7) gradually.
(9) TORQUE the axle nut (7) again until you get a torque value
to between 5 and 10 m.daN (36.87 and 73.75 lbf.ft).
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 9 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
NOTE: It can be necessary to do steps (8) and (9) more than one time to get the
specified torque value.
CAUTION:MAKE SURE THAT YOU INSTALL THE BOLTS FROM THE INSIDE
OF THE AXLE NUT. THUS, THE WASHERS AND THE NUTS ARE
ON THE OUTSIDE OF THE AXLE NUT. IF YOU DO NOT OBEY
THIS INSTRUCTION, YOU CAN CAUSE DAMAGE TO THE MAIN
WHEEL.
(a) Install the bolts (8), the washers (6) and the new IPC -CSN (32-11-13-01-
210) nuts (5) or IPC -CSN (32-11-85-61-210) nuts (5) or IPC -CSN (32-11-
13-03-210) nuts (5).
(13) TORQUE the nuts (5) to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in).
(14) Install the new IPC -CSN (32-11-13-01-200) cotter pins (4) or IPC -CSN (32-11-
85-61-200) cotter pins (4) or IPC -CSN (32-11-13-03-200) cotter pins (4).
(15) Turn the wheel manually to make sure that it is installed correctly.
** ON A/C 162-200
Subtask 32-41-11-420-082-W
D. Installation of the Fan
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 10 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
NOTE: The locating pin (23) puts the joint (10) in the correct position. It locks
the joint so that it cannot turn on the wheel (1).
(b) TORQUE the screw (20) to between 0.28 and 0.34 m.daN
(24.78 and 30.09 lbf.in).
(c) Make sure that the grommet is in position. If the TPIS is not installed, make
sure that the obturator is installed on the grommet.
1 If the grommet is missing, refer to the applicable CMM and send the
brake cooling fan to the overhaul shop.
(d) Install the shroud (12) on the joint (10).
NOTE: Use the locating pins (11) on the joint (10) to put the shroud (12) in
the correct position.
NOTE: All the edge of the shroud (12) must touch the wheel.
NOTE: The TPIS hole location of the shroud (12) is aligned with the joint
grommet.
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 11 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
1 Install the debris guard (16). Make sure that you engage the splines (21)
of the tachometer drive shaft in the splines of the bushing (17).
NOTE: Use the locating pins (11) to put the debris guard (16) in the
correct position.
2 Install the screws (15) and the washers (14) or the news IPC -CSN (32-
48-51-04-035) tab-washers (14) (if installed).
3 TORQUE the screws (15) to between 1.6 and 1.9 m.daN
(11.80 and 14.01 lbf.ft).
4 Safety the tab-washers (14) (if installed).
** ON A/C 101-161
NOTE: The locating pin (23) puts the joint (10) in the correct position. It locks
the joint so that it cannot turn on the wheel (1).
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 12 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
(b) TORQUE the screw (20) to between 0.28 and 0.34 m.daN
(24.78 and 30.09 lbf.in).
(c) Install the shroud (12) on the joint (10).
NOTE: Use the locating pins (11) on the joint (10) to put the shroud (12) in
the correct position.
NOTE: All the edge of the shroud (12) must touch the wheel.
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 13 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE
JOB CARD MPD-TASK:
CEB - A318/A319/A320/A321 AMM TASK : 32-41-11-400-006-A
32-41-11 PB 401
TITLE:
A/C Reg.:
32-41-11-400-006-A - Installation of the MLG Wheel
** ON A/C 153-153, 167-167
MECH. INSP.
NOTE: Use the locating pins (11) to put the debris guard (16) in the
correct position.
3 Install the screws (15) and the new IPC -CSN (32-48-51-04-035) tab-
washers (14).
4 TORQUE the screws (15) to between 1.6 and 1.9 m.daN
(11.80 and 14.01 lbf.ft).
5 Safety the tab-washers (14).
** ON A/C ALL
5. Close-up
Subtask 32-41-11-860-117-A
A. Aircraft Maintenance Configuration
(1) Inflate the tire to the unloaded pressure (Ref. AMM TASK 12-14-32-614-001) .
(2) Lower the aircraft on its wheels (Ref. AMM TASK 07-12-00-582-002) .
(3) Make sure that the PARK BRK control switch is set to ON.
(4) Do a check of the pressure of the tire (Ref. AMM TASK 32-41-00-210-003) .
(5) Make sure that the work area is clean and clear of tools and other items.
(6) Remove the safety devices from the main gear (Ref. AMM TASK 32-00-00-081-
001) .
Subtask 32-41-11-865-117-A
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
** ON A/C 101-200
JCP Title: temporary job card package CERTIFICATE OF TASK / INSPECTION COMPLETION: Page 14 of 14
JCP Ref: reference DATABASE REV DATE: Nov 01/2018
CERTIFIES THAT THE TASK / INSPECTION HAS BEEN COMPLETED TO THE REQUIRED PRINT DATE: Feb 15/2019 00:07
STANDARD AND SUPPORTS THE FINAL MAINTENANCE RELEASE / CERTIFICATE OF RELEASE
TO SERVICE