Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
GENERAL
Version history:
Version 4 30.01.07 One manual test step added on page 3. Test specifications for
WCDMA phones updated on page 5
Version 3 29.08.06 Updates to availability of test scripts, GoNoGo test specifications
for GSM phones and WCDMA phones. Appendix III added.
Version 2 02.06.05 WCDMA specification added
Version 1 13.02.04 Initial version
The GoNoGo Test is required after all level 1 & 2 repairs and has to be
performed with the assembled phone to ensure the quality of serviced
products. The test shall be done for each, by the phone supported band and
network technology.
The supported equipment and links to the support pages of the manufacturer
you can find in the table below.
http://www.willtek.com/english/nokia
Yokogawa GSM / WCDMA VC230
http://www.yokogawa.com/tm/NOKIA/VC200/
Anritsu GSM / WCDMA MT8510B
https://www1.anritsu.co.jp/download/mservice/Login.asp
APPENDIX I
GoNoGo test specification for GSM phones
GSM test channel range specification (Please pay attention to the right attenuation)
GSM 850: Channel low range: 128 - 138, mid range: 185 - 195 , high range: 241 - 251 Serv. Channel = 128
GSM 900: Channel low range: 1 - 11 , mid range: 57 - 67 , high range: 114 - 124 Serv. Channel = 1
GSM 1800: Channel low range: 512 - 523 , mid range: 690 - 710 , high range: 874 - 885 Serv. Channel = 600
GSM 1900: Channel low range: 512 - 522 , mid range: 653 - 669 , high range: 800 - 810 Serv. Channel = 600
Manual teststeps Specification
Visual Inspection for refurbished phones according to "Definition of swap phones"
Visual Inspection without refurbishment check if assembling is completed and no dust to see
LED test Displ. LED and key. LED has to light up during switch ON
Monochrome-display test during power on phase every display-pixel has to come up black during switch ON
Color-display test during power on phase two defect pixels are allowed to be visible during switch ON
Key and joystick test every key and joystick has to trigger the right function
Charge function phone has to recognize a connected charger
Test steps for RF-Measurem. GSM-900/1800 Channel P.-Level Low Limit High Limit Unit
CALL TEST (Mobile station -> Base station) dial the number “1234567890#*”
GSM900 PEAK TX POWER Low 5 28.0 38.0 dBm
RX QUALITY Low 5 0 3
SACCH RXl=-75 Low 5 20 50
GSM900 PEAK TX POWER Mid 5 28 38 dBm
GSM900 PEAK TX POWER High 5 28 38 dBm
PHASE ERR MEAN RMS High 5 0.0 15.0 deg
TX PHASE ERR PEAK High 5 0.0 40.0 deg
TX FREQ ERR FREQ High 5 -150 150 Hz
TX POWER RAMP High 5 Pass / Fail
RX QUALITY High 5 0 3
SACCH RXl=-75 High 5 20 50
GSM900 PEAK TX POWER High 15 8.0 18.0 dBm
TX POWER RAMP High 15 Pass / Fail
Handover from GSM 900 to GSM1800 PASS / FAIL
GSM1800 Peak TX power Low 0 25 35 dBm
RX QUALITY Low 0 0 3
SACCH RXl=-75 Low 0 20 50
GSM1800Peak TX power Mid 0 25 35 dBm
GSM1800Peak TX power High 0 25 35 dBm
PHASE ERR MEAN RMS High 0 0.0 15.0 deg
TX PHASE ERR PEAK High 0 0.0 40.0 deg
TX FREQ ERR FREQ High 0 -250.0 250.0 Hz
TX POWER RAMP High 0 Pass / Fail
RX QUALITY High 0 0 3
SACCH RXl=-75 High 0 20 50
GSM1800 Peak TX power High 10 5.0 15.0 dBm
TX POWER RAMP High 10 Pass / Fail
END GSM1800 CALL / Base station PASS / FAIL
CALL TEST GSM 900 (Base Stat.->Mobile Stat.) IHF or Buzzer (Vibra) Test PASS / FAIL
AUDIO ECHO TEST (manually) PASS / FAIL
END GSM 900 CALL / Base station PASS / FAIL
Teststeps for RF-Measurem. GSM-850/1900 Channel P.-Level Low Limit High Limit Unit
CALL TEST (Mobile station -> Base station) dial the number “1234567890#*”
GSM850 PEAK TX POWER Low 5 28.0 38.0 dBm
RX QUALITY Low 5 0 3
SACCH RXl=-75 Low 5 20 50
GSM850 PEAK TX POWER Mid 5 28 38 dBm
GSM850 PEAK TX POWER High 5 28 38 dBm
PHASE ERR MEAN RMS High 5 0.0 15.0 deg
TX PHASE ERR PEAK High 5 0.0 40.0 deg
TX FREQ ERR FREQ High 5 -150 150 Hz
TX POWER RAMP High 5 Pass / Fail
RX QUALITY High 5 0 3
SACCH RXl=-75 High 5 20 50
GSM850 PEAK TX POWER High 15 8.0 18.0 dBm
TX POWER RAMP High 15 Pass / Fail
Handover from GSM 850 to GSM1900 PASS / FAIL
GSM1900 Peak TX power Low 0 25 35 dBm
RX QUALITY Low 0 0 3
SACCH RXl=-75 Low 0 20 50
GSM1900Peak TX power Mid 0 25 35 dBm
GSM1900Peak TX power High 0 25 35 dBm
PHASE ERR MEAN RMS High 0 0.0 15.0 deg
TX PHASE ERR PEAK High 0 0.0 40.0 deg
TX FREQ ERR FREQ High 0 -250.0 250.0 Hz
TX POWER RAMP High 0 Pass / Fail
RX QUALITY High 0 0 3
SACCH RXl=-75 High 0 20 50
GSM1900 Peak TX power High 10 5.0 15.0 dBm
TX POWER RAMP High 10 Pass / Fail
END GSM1900 CALL / Base station PASS / FAIL
CALL TEST GSM 850 (Base Stat.->Mobile Stat.) IHF or Buzzer (Vibra) Test PASS / FAIL
AUDIO ECHO TEST (manually) PASS / FAIL
END GSM 850 CALL / Base station PASS / FAIL
- For a triple-band phone, please test the supported third band (GSM 1800
or GSM 1900) separately according to the specifications above.
- For a quad-band phone please run all tests listed above.
APPENDIX II
There are two tests to be performed, the first measures the RF performance
parameters and the second is a simple check of audio performance and
general call capability in a voice call.
RF performance testing:
Tests steps are based on specifications from 3GPP TS 34.121. Limits here
are generally wider than 3GPP to allow for tester accuracy, operator
variability and test environment factors.
The following checks will be performed in a 12.2kbps RMC call. The tests
have to be done for each supported band on three different channels as
shown below.
GoNoGo test specification for WCDMA phones (shall be performed for each supported band)
Description Channel Low Limit High Limit Unit
Max TX Power (Aver.) Power Class 4 (21dBm) Low 17,0 24,0 dBm
Power Class 3 (24dBm) Low 19,0 26,0 dBm
TX ON Power (Open loop test normalized) Low -12 +12 dB
Inner Loop TPC / 10 times -1dB step Low -13 -7 dBc
Carrier Frequency Error Low -0.1 / -190 0.1 / 190 ppm/Hz
Error Vector Magnitude (RMS) Low 0 17.5 %
BER at –106.7 dBm Low 0 0.1 %
Max TX Power (Aver.) Power Class 4 (21dBm) Mid 17,0 24,0 dBm
Power Class 3 (24dBm) Mid 19,0 26,0 dBm
TX ON Power (Open loop test normalized) Mid -12 +12 dB
Inner Loop TPC / 10 times -1dB step Mid -13 -7 dBc
Carrier Frequency Error Mid -0.1 / -190 0.1 / 190 ppm/Hz
Error Vector Magnitude (RMS) Mid 0 17.5 %
BER at –106.7 dBm Mid 0 0.1 %
Max TX Power (Aver.) Power Class 4 (21dBm) High 17,0 24,0 dBm
Power Class 3 (24dBm) High 19,0 26,0 dBm
TX ON Power (Open loop test normalized) High -12 +12 dB
Inner Loop TPC / 10 times -1dB step High -13 -7 dBc
Carrier Frequency Error High -0.1 / -190 0.1 / 190 ppm/Hz
Error Vector Magnitude (RMS) High 0 17.5 %
BER at –106.7 dBm High 0 0.1 %
APPENDIX III
For GSM bands 900/1800/1900 GSM-tester Willtek 4107 plus coupler 4916
(Shield box 4921 is recommended to eliminate interference problems)
GSM/WCDMA-tester Willtek 3100 plus Willtek coupler 4916 and shield box 4921.
(Recommended to eliminate interference problems)
GSM/WCDMA tester Yokogawa VC230 plus coupler and shield box VC-shield
model 733062. (Recommended to eliminate interference problems)