Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. SCOPE
This NES stipulates the coating materials to be used on ferrous automotive parts. (Excluding the
non-ferrous metal parts and stainless steels.) The materials must conform to NES M 0301 (Substance Use
Restrictions).
Note: The units and numerical values expressed in this standard are based on SI units.
Conventional units are noted in { } for informative reference.
2. TYPES
The coating material types shall be as listed in Table 1. (1)
Table 1 Types
Applicable parts
Division Type Classification Symbol
example
Cation type Standard deposited coating materials CED
Suspension member
deposited Edge cover deposited coating materials CED-E
Deposited Suspension link
coating Edge cover thick film deposited coating
coating Brackets
materials(1) materials
CED-T
materials
Hub bolt
Anion type deposited coating materials AED
(Service parts)
Room temp. Within 30 min. at room
ET-1A
drying type temp.
Spray Engine block
Forced drying Within 30 min. at temp.
coating ET-1B Knuckle arms
type below 80°C
materials Brackets
Within 30 min. at temp.
Baking type ET-1C
Coating below 140°C
materials Room temp. Within 30 min. at room
ET-2A
for parts drying type temp.
Immersion
Forced drying Within 30 min. at temp.
General coating ET-2B Axle parts
type below 80°C
coating materials
materials(2) Within 30 min. at temp.
Baking type ET-2C
below 140°C
Room temp. Within 30 min. at room
ET-3A
drying type temp.
Brush
Forced drying Within 30 min. at temp. Ground surface of
coating ET-3B
type below 80°C chassis parts
materials
Within 30 min. at temp.
Baking type ET-3C
below 140°C
Within 30 min. at temp. Wiper motor
Powder coating materials ET-2D
below 140°C Coil springs
1
Note ( ): Utmost precautions must be taken when applying cation deposited coating materials to parts subjected to tension
(torsion bars, springs, etc.) due to the possibility for hydrogen embrittlement.
2
( ): As potential characteristics of casting and forging parts, the following issues are known.
<1> Since oxide scale is formed on the surface, adhesion of coating is not adequate.
<2> Since the extent of surface roughness is great, coating thickness may not be uniform.
<3> Since many casting/forging parts have a large heat capacity, it is difficult to apply baked finish.
From the reasons above, utmost precautions need to be taken to ensure the coating quality specified in this
standard.
- 1/7 -
M5083 [2016-N]
3. ELECTRO-DEPOSITION COATING MATERIAL
-2-
M5083 [2016-N]
3.2 Quality of coated film
The quality of deposited coating film shall be as listed in Table 3.
Use the test piece with chemical conversion treatment of SP120 specified in NES M 2020.
Remarks: The dry coated film thickness shall be 30 µm for CED-T, and 20 µm for others.
-3-
M5083 [2016-N]
4. GENERAL COATING MATERIALS
-4-
M5083 [2016-N]
4.2 Quality of general coated films
Quality of coated films shall be as listed in Table 5, 6, 7.
Use the test piece of SP120 specified in NES M 2020.
-5-
M5083 [2016-N]
Table 6 Coated Film Quality of General Coating Materials (Rust Preventive Performance)
Salt Spray Test
-6-
M5083 [2016-N]
ANNEX
[Revision in March 2016]
1. Revision objectives
Expressions which may cause misunderstanding have been reviewed.
-7-