Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
These are the PDMS Piping Commands which are used while modeling in the PDMS. Designer can use
this commands while modeling in PDMS. These PDMS piping commands are helps to designer while
modeling
1. Axes at CE= to check the axes of component like North, South, East, West
direction
2. Q axes at ph= to check the head of the branch of the pipe.
3. Q axes at pt= to check the tail of the branch of the pipe.
4. Q Hstu= to show the branch head tube attribute
5. Q Lstu= to show the branch tail tube attribute
6. Q Hbore= to check the arrive bore or diameter of the component
7. Q Tbore= to check the leave bore or diameter of the component
8. Q Spre= to check the specification of the particular component
9. Q pspec= to check material class of the pipe.
10. New elbow choo all= to create new elbow through command line
11. New tee choo all= to create new tee through command line
12. New gasket choo all= to create new gasket through command line
13. New flange choo all= to create new flange through command line
14. New olet choo all= to create new olet through command line
15. Unclaim all= to remove claim the by user so other user can work in that
pipe, equipment, member,structure.
16. Getwork= to refresh the design model. After get work all the change done any
user will show in the model.
17. Axes at hpos= To check the branch head axes
18. Axes at tpos= To check the branch tail axes
19. Q ltle= to check the length of the spool between the two component
20. Conn ph to fir member= to connect the branch head to first member of the
next branch by common line
21. Conn pt to fir member= to connect the branch tail to last member of the next
branch by common line
22. Q ori = to check the orientation of the component
23. Dist= to give the distance between two component
24. Clea= to give the spool length between the two component
25. Conn= connect to the member
26. Fconn= to component forcefully
27. Q styp= to check the component selection type
28. Q dtxr= to check the detail text description of the component
29. Q mtxx= to check the material of the component
30. Q mode= to check the mode weather it in forward mode or backward mode
31. Q para= to check the parameter of the component
32. Dir tow next= to connect the next member by direction
33. Q ref= to check the reference
34. Add all the pipe within vol ce 500= all pipes to added in the area 500 around
the selected component.
35. Incl= to include the component from one branch to other branch
36. Ori and p3 is up= to orientate the point 3 of the tee in up direction
37. Own= navigate the owner of component
38. Q angle= to check the angle of the component
39. Q atle= to check the length of the first tube of the branch
40. Attype ccnn= comment attachment without dimensions
41. Attype cccc= comment attachment with dimensions
42. Attype xxxx= to set the attachment for isometric break up
43. Ch ce= to check the data inconsistency
44. Dir tow next elb= to align the elbow with next elbow
45. Dir tow id@= to align the elbow by using mouse click on the component
46. Q hcon= to check head connection attached with which branch
47. Q tcon= to check tail connection attached with which branch
48. Q ispec= to check the insulation of pipe
49. Ispec nulref= to remove the insulation of the pipe
50. Mtoc dotd= to appear the component in doted in the isometric
51. Mtoc off= to remove the material off the component. With this command
52. material of the component will not appear in isometric
53. Nex conn= connect to next component
54. Nex thro ce= align the next component in same direction
55. Q p3 = to check the p3 point of the component
56. Q pa= to check arrive point
57. Q pl= to check the leave point
58. Attype flow= to create the flow direction attachment
PDMS commands Equipment Modeling
PDMS COMMANDS
PIPING COMMANDS
b. Q ATT
c. TCONN OPEN
d. Q STEXT