Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Interview Aptitude Reasoning English GD Placement papers HR Current affairs Engineering MCA MBA Online test Login
Explanation:
No explanation is available for this question!
2) What is the desirable safety factor prescribed for the pin type of insulators?
a. 5
b. 13
c. 10
d. 2
ANSWER: 10
Explanation:
No explanation is available for this question!
3) Why is the voltage rating of a multiple shell pin type insulator cannot be increased beyond a limiting
value?
Explanation:
No explanation is available for this question!
a. Radial
b. Parallel
c. Network
d. All of these
ANSWER: Radial
Explanation:
No explanation is available for this question!
5) Which component connects the substation to the area where power is to be distributed?
a. Distributors
b. Service mains
c. Feeders
d. All of these
ANSWER: Feeders
Explanation:
No explanation is available for this question!
6) The cost of material used in a distribution circuit per kVA of the distributed power varies as
Explanation:
No explanation is available for this question!
7) Name the cable which connects the distributor to the consumer terminals.
a. Distributors
b. Service mains
c. Feeders
d. All of these
Explanation:
No explanation is available for this question!
8) What is the permissible limit of voltage variations allowed in the distribution systems?
a. ± 2 %
b. ± 5 %
c. ± 10 %
d. ± 6 %
ANSWER: ± 6 %
Explanation:
No explanation is available for this question!
ANSWER: Where power is generated at low voltage and substation is located at the centre of the load
Explanation:
No explanation is available for this question!
10) What is the main advantage of ring main system over radial system?
a. i and ii only
b. ii and iii only
c. i and iii only
d. i, ii and iii
Explanation:
No explanation is available for this question!
11) The null point of a uniformly loaded distributor feed at equal voltage at both ends lies at
a. Mid point
b. Either end
c. Two third distance from one end
d. One fourth distance from one end
Explanation:
No explanation is available for this question!
12) In a distribution system, which of the following items shares the major cost?
a. Conductors
b. Earthing systems
c. Distribution transformer
d. Insulators
Explanation:
No explanation is available for this question!
Explanation:
No explanation is available for this question!
14) In a dc 3 wire distributor using having unequal loads on the two sides
Explanation:
No explanation is available for this question!
15) Why are the balancers fields cross connected in a three wire distribution system?
Explanation:
No explanation is available for this question!
16) Which distribution system is energised by two or more generating stations or substations?
a. Radial systems
b. Interconnected systems
c. Ring main systems
d. All of these
Explanation:
No explanation is available for this question!
a. One
b. Two
c. Three
d. All of these
ANSWER: Three
Explanation:
No explanation is available for this question!
18) If the voltage of the system is about 230 V, then what would be the highest and the lowest
permissible voltage?
Explanation:
No explanation is available for this question!
19) What will be the pd at point B if a pd of 300 V is maintained at a point A, for a 2 wire dc distributor
cable AB if 2 km long and supplies loads of 100A, 150A, 200A, and 50A suited at 500m, 1000m, 1600m,
and 2000m from the feeding point A. Each conductor has a resistance of 0.01 Ω per 1000 m.
a. 288 V
b. 287.6 V
c. 295.36 V
d. 291.2 V
21) A 2 wire dc street mains AB, 600 m long is fed from both ends at 220 V. Loads of 20 A, 40 A, 50 A and
30 A are tapped at distances 100m, 250m, 400m and 500m from the end A. If the area of cross section of
distributor is 1 cm2, what will be the minimum consumer voltage? If ? = 1.7 * 10-6 Ω cm.
a. 220 V
b. 215.69 V
c. 218.36 V
d. 222.58 V
22) A distribution system is shown in figure with load currents as marked. The two ends of the feeder
are fed by voltage sources such that Vp = Vq = 3 V, the value of the voltage Vp for a minimum voltage of
220 V at any point along the feeder is
a. 225.89 V
b. 222.89 V
c. 220.0 V
d. 228.58 V
23) A uniformly loaded dc distributor is fed at both ends with equal voltages. In comparison to a similar
distributor fed at one end only, what will be the maximum voltage drop?
a. One fourth
b. Half
c. One third
d. One sixth
24) A uniformly loaded dc distributor is fed at both ends with equal voltages. In comparison to a similar
distributor fed at one end only, what will be the drop at the midpoint be?
a. One fourth
b. Half
c. One third
d. One sixth
25) Installation of capacitors at suitable locations and of optimum size in a distribution system results in
a. i only
b. i and ii only
c. iii only
d. All of these
Explanation:
No explanation is available for this question!
Explanation:
No explanation is available for this question!
a. Reduce current
b. Increase current
c. Reduce voltage drop
d. Compensate for voltage drop
Explanation:
No explanation is available for this question!
28) Why is the floating neutral in a three phase supply considered as undesirable?
Explanation:
No explanation is available for this question!
29) A 300m ring distributor has loads as shown in the fig. The distances are in metres. The resistance of
each conductor is 0.2 W per 1000 metres and loads are tapped off at B, C, D. If the distributor is fed at A at
240 V, what will be the voltage at B?
a. 220.6 V
b. 236.9 V
c. 240.6 V
d. 235.97 V
Explanation:
No explanation is available for this question!
a. Balanced
b. Unbalanced
c. Both (a) and (b)
d. None of these
ANSWER: Unbalanced
Explanation:
No explanation is available for this question!
32) In a balanced 3 phase, 4 wire ac system the phase sequence is RYB. If the voltage of R phase = 230
∠ 0° volts, then what will be the B phase?
a. 230 ∠ - 120°
b. 230 ∠ - 90°
c. 230 ∠ - 90°
d. 230 ∠ - 120°
Explanation:
No explanation is available for this question!
34) A single phase AC distributor supplies two single phase loads as shown. What is the voltage drop
from A to C?
a. 4.5 V
b. 30 V
c. 31.5 V
d. 20 V
35) An industrial consumer has a load pattern of 2000 kW, 0.8 lag for 12 hours and 1000 kW UPF for 12
hours. What is its load factor?
a. 10.5
b. 0.75
c. 0.6
d. 2.0
Explanation:
No explanation is available for this question!
37) Strain and Shackle type insulators are provided on which type of plane?
a. Vertical plane
b. Horizontal plane
c. On the surface
d. All of these
Explanation:
No explanation is available for this question!
a. Pin type
b. Shackle type
c. Suspension type
d. Stay insulators
Explanation:
No explanation is available for this question!
39) Assembly of which type of insulators are used as strain type of insulators?
a. Pin type
b. Shackle type
c. Suspension type
d. None of these
Explanation:
No explanation is available for this question!
40) Which type of insulators is mainly used for low voltage overhead lines?
a. Pin type
b. Shackle type
c. Suspension type
d. None of these
Explanation:
No explanation is available for this question!
Related Content
High Voltage Engineering Test Set - 2 High Voltage Engineering Test Set - 1
Power System - Transmission & Distribution Test Se Power System - Transmission & Distribution Test Se
Power System - Transmission & Distribution Test Se Power System - Transmission & Distribution Test Se
Power System - Transmission & Distribution Test Se Power System - Transmission & Distribution Test Se
Power System - Generation Test Set - 6 Power System - Generation Test Set - 5
Power System - Generation Test Set - 4 Power System - Generation Test Set - 3
Power System - Generation Test Set - 2 Power System - Generation Test Set - 1
Switchgear and Protection Test Question - 3 Switchgear and Protection Test Question - 2
Switchgear and Protection Test Question - 1 Electrical Measurements & Units Test Questions - 9
Electrical Measurements & Units Test Questions - 8 Electrical Measurements & Units Test Questions - 7
Electrical Measurements & Units Test Questions - 6 Electrical Measurements & Units Test Questions - 5
Electrical Measurements & Units Test Questions - 4 Electrical Measurements & Units Test Questions - 3
Electrical Measurements & Units Test Questions - 2